OpenSUSE Network :: No Wlan With FRITZ WLAN USB Stick N 2.4 On 11.2
Nov 27, 2009
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
View 5 Replies
ADVERTISEMENT
Jan 17, 2010
I have installed open SuSE 11.2 and would like to use my Fritz ups Stick.
I have read a couple of threads about this issue and I do not know if I can follow those solutions presented for oS 11.0 and earlier versions.
View 8 Replies
View Related
Mar 15, 2011
i have just installed a Fritz Wlan USB stick on a practically fresh Maverick 32 Bit install with ndiswrapper.(i used this guide [in german] [URL]...so far so well, problem is, i cant enable the wireless. As far as i can see, this is no "on-button" issue. The build in wireless is either dead or never been there. It shows in the output below, but the "wifi-on/off" button doesnt do anything to the LED thats supposed to turn on and in an case... no connection. I think basically what my problem is that i can't figure out how to enable the wireless (its greyed out in the network-manager) i also installed the 32Bit version of the driver on a 32Bit Notebook. below is some output of what i found on other threads to try:
[Code]...
View 9 Replies
View Related
Sep 30, 2009
I can't get my wlan running, although it already worked on my notebook (Dell Inspiron 1545) with opensuse 11.1. Then I installed debian and, I don't know how, it changed my kernel in grub from .pae to .debug (renameing in grub didn't help)
According to the messages scanning fails
My wlan-controller is:
Router is avm Fritz!Box and is working fine with other notebooks and the lan of the Dell
I loaded down and installed the driver from Bradcom (hybrid-portsrc-x86_32-v5.10.91.9.3.tar.gz)
dmesg came up with a failure: not ipv6 server found - so I deactivated it
Below find further info:
View 1 Replies
View Related
Jul 25, 2010
I can't get WLAN up on my Dell Mini 10v (BCM 4312)/openSUSE 11.3/LXDE. And yes, I have thoroughly read iwfingers's 'Getting your Wireless to Work'. After installing openSUSE 11.3 ifconfig can see eth0, l0 and wlan0. No WLAN running. dsmesq|grep firmware prompts me to '/usr/sbin/install_bcm43xx_firmware"
After having done that and reboot ifconfig can only see eth0 and l0. Installing broadcom-wl-5.60.48.36-7.pm.16.4.i586.rpm broadcom-wl-kmp-default-5.60.48.36_k2.6.34.0_12-7.pm.16.4.i586.rpm (current ones from Packman) does, Shall I try to install the drivers without installing the firmware first?
Why does broadcom-wl-kmp-default-5.60.48.36_k2.6.34.0_12-7.pm.16.4.i586.rpm install a new default kernel? Ubuntu Netbook Remix 9.04 had no problems with WLAN.
View 6 Replies
View Related
Apr 6, 2011
Brand new to the OpenSuse project. I'm have an old AMD Duron running 11.3 and I am having no luck in connecting to the www. I'm using a D-Link usb wireless adapter. I seem to have an IP address for the PC. here is the print from ifconfig:
wlan0 Link encap:Ethernet HWaddr 00:12:0E:45:75:F5
inet addr:192.168.2.7 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::218:eff:fec45:75f5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:246 errors:0 dropped:0 overruns:0 frame:0
[Code]...
View 3 Replies
View Related
Jul 6, 2011
Being in China has some disadvantages reagardings internet.To enjoy unfiltered speed and access I use my non mainland mobile phone card.
Using LAN works fine in the office.But if I connect the WLAN USB dongle except skype nothing works.
ifconfig
eth1 Link encap:Ethernet Hardware Adresse 00:1A:A05:26:C5
inet Adresse:192.168.1.3 Bcast:192.168.1.255 Maske:255.255.255.0
inet6 Adresse: fe80::21a:a0ff:fed5:26c5/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
code....
View 5 Replies
View Related
Nov 27, 2010
I have just installed opensuse 11.3. I am absolutely new for Linux and for this forum. I have tried to open Network manager to configure my wlan. But its not starting. How to start network manager and configuring my wlan.
View 4 Replies
View Related
Jan 23, 2010
recently ran into a problem with my internet access. Im using open suse 11.2 on a Dell Vostro 1520 laptop. I managed to get my wlan running and i can use firefox to access my router. In my router the laptop is also showing as connnected, dhcp reserved an ip for it.However if i try to browse the internet, no page is loading, actually no software that needs access to the web is working.
View 3 Replies
View Related
May 1, 2011
I just installed version 11.4 on my system of a toshiba satellite l505d-es5025 64bit.My wlan will not show up at all.I installed ndiswrapper, and all of the wlan from yast.
View 2 Replies
View Related
Feb 15, 2010
Am all of 2 days old on Opensuse 11.0 having just installed it on my old PC. All my experience has been with XP/Vista and Macs and it took some courage to finally try this out. My Belkin F5D9050 wireless(g+ MIMO) usb network card is recognised in yast but does not connect to the internet. On reading through forums I understand that this adaptor uses RAlinks RT73 chipset and support for should already be available in the OS. Is this correct ? If not, where do I get the driver for this and how do I install this. As per the Belkin site, Opensuse driver support isnt listed. Am struggling due to the unfamiliar environment and am not aware of terminal commands.
View 1 Replies
View Related
Apr 22, 2010
I get connected to the internet via a router. The router dials to my provider and is connected to my computers via LAN and WLAN (mostly WLAN, see below). A few days ago I installed Suse11.2 to an old laptop (connected both ways: ethernet with wire and wireless ethernet).
The access to the online repositories worked only after I added the LAN-Adapter (Eth0) to the Demilitarised Zone of the firewall (I did also with the WLAN Adapter).
1. Is this normal?
2. Should I add the network devices now to an other zone?
I want to update my main laptop now from openSuse11.1 to 11.2 via new installation (from DVD) and make this installation right.
Or should I install only the data on the DVD and update after the installation via Yast?
(My main laptop has also an loose contact at the ethernet adapter.)
Greetings pistazienfresser
Now I am using (on my main laptop = Samsung X20) openSuse 11.1 and Gnome 2.24.1 (mostly, 1 account is using KDE) and Kernel Linux 2.6.27.45-01.1-pae. "/home" is on an separated partition (as part of an extended partition). I have also 2 NTFS partitions for Windows XP (System and Data), and a FAT, a root (/) and a swarp partition. My router is a AVM fritzbox 7270 (firewall should be included).
View 6 Replies
View Related
Aug 16, 2010
I'm trying to install the drivers for my Wlan card, I've downloaded the drivers in the tar.gz-file from Broadcom and untar-ed it in my /home/<username>/hybrid_wl-folder and cd'ed to it and I try to run "make" but I get an error: KBUILD_NOPEDANTIC=1 make -C /lib/modules/'uname -r' /build M='pwd' make: *** /lib/modules*2.6.31.5-0.1-default/build: No such file or directory. Stop make: *** [all] Error 2
I'm getting really desperate, I need my Wlan on Wednesday. I'm following the README but this is what I get.
View 7 Replies
View Related
Nov 12, 2010
I'm unable to get into my university's WLAN network. LAN works just fine, but sometimes it's quite convenient to be able to access stuff wirelessly. It doesn't seem to be a hardware problem, because if I configure my computer according to our computer department's instructions it works fine with Ubuntu (currently I carry around a stick to get into the Internet when I really need it and don't have a cable). Some info:
My device:
Broadcom WLAN controller on a Lenovo G560
My system:
OpenSUSE 11.3 64-bit
The drivers are installed, I can get into normal private networks, but have never managed to get into the university network except for with Ubuntu.
The university instructions tell me to use the following settings:
Security: WPA Enterprise
Authentification: TTLS
Inner Authentification: PAP
Username: My username
Password: Password
CA Certificate: Deutsche_Telekom_Root_CA_2.pem
In the KDE instructions, they tell you to write "anonymous" into the anonymous identity field, but in the GNOME instructions it says to leave it blank. In Ubuntu, I leave it blank and it works.
I've got the recommended settings, which also work in GNOME.
I'd ask the tech support here, but I am the tech support We've got it working with other systems, like I said, but not with SUSE, and I'm a SUSE fan.
View 9 Replies
View Related
Mar 29, 2010
I have searched around a bit for a knetwork manager issue I am having on my opensuse 11.2 32 bit install. My wireless card is an 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) I am currently using the Broadcom wl driver
I am on the Internet with this machine as I am typing using the older "ifup" method. I am having great difficulty connecting to the Internet when I use knetwork manger though. The strange part is when I am connected to my router with knetwork manager, I can log into my Router, but I can not get to any web-page/ping any outside address.
so far the best (I was able to locate) advice I was able to get is located in this post. < Broadcom wireless, partchy internet - openSUSE Forums > following a posted how to to disable IPV6 (I suspect this may be the issue??), I was unable to locate modprobe.conf, or modprobe.conf.local, even after I updated via updatdb. I gave a shot at entering in "disable_ipv6=1" into "menu.lst". However, this did not solve my issue with knetwork manager. If my network information is needed when I am "connected" utilizing knetwork manager
View 9 Replies
View Related
May 8, 2010
i installed suse (KDE) on my old notebook and now I'm trying to get the wlan to connect to our router and can't figure out how to get it to work. My card seems to work, the network manager even finds the router, but i just cant get a connection. I followed the steps of the "Getting Your Wireless to Work" thread and these are the results:
[Code]....
- i messed around a bit with the network settings and might have cluelessly broken something (or broken it more)
- i tried a usb-wlan-card as an alternative, which didn't work either, but could possibly have messed things up even more.
View 7 Replies
View Related
Jan 12, 2010
My Dell Vostro 1520's Dell Wireless 1397 WLAN Mini-Card must not have been set-up correctly, as the Network Manager won't even let me select the wireless tab. Please just explain to me, step by step, what exactly I must do to make it work! Additionally, I can't figure out how to disable my Touchpad's Tap to Click funtionality, which must be done if I'm to effectively use my current KDE installation of openSUSE
View 9 Replies
View Related
Jul 23, 2015
Since a recent update on Stretch, I have been unable to use the network-manager to connect to my home wireless network on my laptop. It was working fine before. I did not change any settings on the WLAN router. I can still connect to other wireless networks at work and university, just not this particular one at home. All other non-Debian devices in my household are still able to connect just fine.While figuring this out, I have tried connecting manualy with ifup but I don't really know how that works. Right now there is only the loopback entry in /etc/network/interfaces.
Below is the output of syslog, when gnomes network-manager is trying to connect, but fails.
Code: Select allJul 19 20:01:57 debian NetworkManager[6705]: <info> (wlan0): Activation: starting connection 'Affenbande'
Jul 19 20:01:57 debian NetworkManager[6705]: <info> (wlan0): Activation: Stage 1 of 5 (Device Prepare) scheduled...
Jul 19 20:01:57 debian NetworkManager[6705]: <info> (wlan0): Activation: Stage 1 of 5 (Device Prepare) started...
[code]...
View 14 Replies
View Related
Dec 27, 2010
I bought an USB-WLAN stick, which does not recognize any network. A Ralink 802.11 bg WLAN Stick works fine, but the Ralink 802.11 n WLAN Stick does not work unfortunately. Both get recognized by the nm-applet of network manager but only the first one recognizes my network and is able to connect to it.
[Code]....
View 2 Replies
View Related
Nov 24, 2010
I have found instructions but they are not working. I am new to Ubuntu and have only had a few classes that dealt with Fedora and CentOS. So I am rather new to Linux in general. The drivers say they are compatible with linux kernel 2.6 and later so I am going to assume they should work with ubuntu--am I correct in this assumption? If so, when one installs anything in ubuntu should one be set as the admin?
View 4 Replies
View Related
Jul 20, 2009
Recently, I had the courage of installing Fedora 11 on my laptop while risking of trashing my Windows XP. Fortunately, the installation went fine and windows and fedora seems to be working together. But I needed to reinstall Fedora because I didn't do the partitioning right. After that the problem arises. I couldn't connect to the wlan. The first installation it was working fine. Now I can't. I select the network, enter the password and then it just says "Disconnected" or something like that then nothing else happens. So I had to reinstall it again thinking I did something wrong on the installation. But still it wasn't working. But it seems to be working when I boot from the live cd. I must have messed up my network configuration.
View 7 Replies
View Related
Dec 11, 2010
recently I risked a look to the Linux world and I'm happy so far, but now I've got a Problem, I'm unable to solve by myself. I installed Mint (Julia) on my old Laptop to test Linux. The Laptop has a very old PCMCIA WLAN Card with a Realtek rtl8180 chipset. Everything seems to run perfectly so far with one exception: the WLAN doesn't find any Network to connect although the card and the driver seem to be installed correctly.
Here some code from the terminal:
Code:
lspci
00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M]
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:03.0 Modem: ALi Corporation M5457 AC'97 Modem Controller
[Code]...
View 1 Replies
View Related
Apr 11, 2010
yesterday i set my thinkpad t43p up with open suse, but i need to install my wlan...
i can't find the 12key big no to connect to my DSL telephone connection...
View 3 Replies
View Related
Apr 18, 2011
While it worked out of the box in 11.3, openSUSE 11.4 does not recognize my TP-Link TL-WN821N any more.
Googling a bit, apparently the old ar9170 driver is deprecated and supposedly a new driver carl9170 is integrated in the kernel now, but since it is not working this cannot be quite right.
Unfortunately, I do not understand much of the instructions given at the above two URLs: Should I try to install the old ar9170 driver? If so, I found older, pre-11.4 posts here that seem to indicate that is not so simple as just copying a firmware file somewhere, so how can I install it in openSUSE 11.4? Or should I rather try getting the new carl9170 to work? If so, how can I do this if it is already supposed to be part of the kernel?
The 11.3 Net-Install (from CD) recognised that USB-WLAN-Stick all by itself, installing 11.3 just fine through the air. With 11.4 it didn't work. So I borrowed a WLAN bridge for a couple of days and installed 11.4 now (32bit plain install plus Packman), but even after the install, plugging in that Stick does not do anything.
View 9 Replies
View Related
Jun 6, 2010
I dual boot windows xp and ubuntu 10.04 LTS and the wireless card works perfectly fine in xp so I know its not a hardware/network issue. In ubuntu, it detects wireless networks, will connect to network and work for about 20 seconds.
[Code]....
and it continues on after this alternating between a normal 20ms and high ping over 200ms. The connection refuses to load anything off the internet/local network.
View 5 Replies
View Related
Jul 5, 2010
I've just got a TP-Link wn-851n PCI WLAN card, and the problem is that ubuntu can search for the network, but I can't join into the network after typing the password. I'm sure that it is correct as m Windows notebook is also using that network.
Taking a look in dmesg, and it start to loop this message after I joined the network.
Quote:
View 1 Replies
View Related
Mar 11, 2010
I have a new Dell laptop that I installed OpenSUSE on, but can't get the Dell WLAN card (Broadcom) to activate. I can see it in the hardware listing, and I can attempt to set it up using iwconfig, but when I do an ifconfig it does not show, and when I do a ifconfig wlan0 it tells me the interface is not installed. I feel like I am missing something basic, but just can't seem to put my finger on it.
View 9 Replies
View Related
Jul 17, 2010
I installed openSUSE 11.3 on my notebook (lenovo 510i, Intel Centrino Wireless-N 1000).When I connect to my home wlan with WPA2 there is no problem, but when I try to connect to an open WLAN without encryption, the essid is not set (seen with iwconfig wlan0). If I set it after rcnetwork start wlan0 with iwconfig wlan0 essid the_open_sid, it associates and dhcp is working fine.
Here are the messages that are produced during rcnetwork start wlan0:
Code:
Jul 16 13:51:48 job2 ifplugd(eth0)[4740]: ifplugd 0.28 initializing.
Jul 16 13:51:48 job2 kernel: [ 5819.161280] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X
Jul 16 13:51:48 job2 ifup: eth0 device: Intel Corporation 82577LM Gigabit Network Connection (rev 06)
code....
Is there a log with the wireless card setup commands that are used?
View 8 Replies
View Related
Oct 15, 2010
I've installed openSUSE 11.3 on my new HP 620 and it boots only when the WLAN card is swithched of in BIOS, otherwise the computer hangs up (processing udev with the last statement b43-pci-bridge...).
View 1 Replies
View Related
Jan 20, 2010
on kde4 with knetworkmanager I cannot get past the wep security key on my home router. Every other wlan works, ethernet works, settings are definitely correct because it works with windows, other computers.And on the same computer even with gnome networkmanager! Also it used to work fine earlier. Behavior the same with different users including root, regardless of using kwallet or not. Networkamanager tries to connect and after one or two minutes throws the setting window back at me. I uninstalled and re-installed and deleted all related files I could think of. I even tried a complete fresh installation of opensuse only keeping the /home partition, so the problem must be lying there I guess. But then why all users?
PS opensuse 11.2
kde networkmanager 0.9.svn1043876-1.1.1
View 1 Replies
View Related
