OpenSUSE Install :: 11.3 With Open WLAN Does Not Work
Jul 17, 2010
I installed openSUSE 11.3 on my notebook (lenovo 510i, Intel Centrino Wireless-N 1000).When I connect to my home wlan with WPA2 there is no problem, but when I try to connect to an open WLAN without encryption, the essid is not set (seen with iwconfig wlan0). If I set it after rcnetwork start wlan0 with iwconfig wlan0 essid the_open_sid, it associates and dhcp is working fine.
Here are the messages that are produced during rcnetwork start wlan0:
Code:
Jul 16 13:51:48 job2 ifplugd(eth0)[4740]: ifplugd 0.28 initializing.
Jul 16 13:51:48 job2 kernel: [ 5819.161280] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X
Jul 16 13:51:48 job2 ifup: eth0 device: Intel Corporation 82577LM Gigabit Network Connection (rev 06)
code....
Is there a log with the wireless card setup commands that are used?
View 8 Replies
ADVERTISEMENT
Jul 6, 2011
Being in China has some disadvantages reagardings internet.To enjoy unfiltered speed and access I use my non mainland mobile phone card.
Using LAN works fine in the office.But if I connect the WLAN USB dongle except skype nothing works.
ifconfig
eth1 Link encap:Ethernet Hardware Adresse 00:1A:A05:26:C5
inet Adresse:192.168.1.3 Bcast:192.168.1.255 Maske:255.255.255.0
inet6 Adresse: fe80::21a:a0ff:fed5:26c5/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
code....
View 5 Replies
View Related
Jan 17, 2010
I have installed open SuSE 11.2 and would like to use my Fritz ups Stick.
I have read a couple of threads about this issue and I do not know if I can follow those solutions presented for oS 11.0 and earlier versions.
View 8 Replies
View Related
May 8, 2010
i installed suse (KDE) on my old notebook and now I'm trying to get the wlan to connect to our router and can't figure out how to get it to work. My card seems to work, the network manager even finds the router, but i just cant get a connection. I followed the steps of the "Getting Your Wireless to Work" thread and these are the results:
[Code]....
- i messed around a bit with the network settings and might have cluelessly broken something (or broken it more)
- i tried a usb-wlan-card as an alternative, which didn't work either, but could possibly have messed things up even more.
View 7 Replies
View Related
Nov 27, 2009
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
View 5 Replies
View Related
Oct 15, 2010
I've installed openSUSE 11.3 on my new HP 620 and it boots only when the WLAN card is swithched of in BIOS, otherwise the computer hangs up (processing udev with the last statement b43-pci-bridge...).
View 1 Replies
View Related
Feb 9, 2010
since if read all the forums threads, faqs an tutorials i could find, i hope to find some help here.
i just installed openSuse 11.2, KDE 4.3.1 a fews days ago to see what's it all about. i don't have any experience in writing code or anything besides the few little commands i've learnd through my research. the system is running on an old laptop (amd64 3000+) with enough RAM and HD. now i since my wlan-card is detected but won't work due to missing driver i tried this ndiswrapper-method. i used the ndis-version that was included in the openSuse-dvd with no success, then i de-installed this version to try manually. i downloaded version 1.55 from the ndiswrapper-website, logged into the console as superadmin and followed the install-intructions and for intances this tutorial. now i'm even stuck with the "make"-command as the console tells me "If 'make' is not a typo. in earlier attempts while trying to install the wlan-driver through the dvd-given ndiswrapper version i often got the error "makefile:23: kernel tree not found..."
as the welcome-note for this forum demands here's some output from the console linux-g6rk:/home/mat/ndis # lspci -nn
02:09.0 Ethernet controller [0200]: Linksys, A Division of Cisco Systems [AirConn] INPROCOMM IPN 2220 Wireless LAN Adapter (rev 01) [17fe:2220]dmesg|less [0.331220] aer 0000:00:02.0:pcie02: AER service couldn't init device: no _OSC support (i guess that's the line telling me that my wlan-card has no firmware as i found nothing else for that matter) i know there many threads about this topic but i've spend the last two days looking for answers and the stuff i found either didn't work or was explained so weird that i could make anything out of it.
View 2 Replies
View Related
Feb 12, 2009
I installed F10 today. From live-usb wlan worked fine, but after installing it doesn't find any networks. I tried to google this problem, but everybody says wifi works out of the box. Not for me.
Solved: I disappled wireless networking and appled it again. It found all networks.
View 1 Replies
View Related
Dec 7, 2009
I have installed Fedora 12 on my laptop.Installing my Broadcom BCM 4312 wireless drivers works just fine, but after a reboot I have to reinstall them. modprobe wl, modprobe wlan0 etc doesn't work either. I need to reinstall them every time I reboot.
View 7 Replies
View Related
Jan 16, 2010
my network was a dream to set up under ubuntu 9.10. all i had to do was enter pass key, then that was it. Works brilliantly.
Different matter with studio. The thing I notice in network connections is, it doesn't want to retain my pass phrase, if I go back into properties the phrase is blank. As far as I can tell the wireless card has been reconcognized and is communicating with router.
My system is: asus p5ql-vm epu, intel core2 duo 2.8 e7400, 4gb 1067 ddr2 ram, belkin f5d7050 v4000, edimax router.
Here is the info requested in the sticky:
kevin@ubuntu:~$ lsusb
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 003: ID 045e:00dd Microsoft Corp.
Bus 008 Device 002: ID 046d:c501 Logitech, Inc. Cordless Mouse Receiver
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
code....
View 3 Replies
View Related
Feb 21, 2010
On my HP TX2500 laptop, dual-booting Vista and 9.04, Ubuntu installation found the WLAN and it works fine.I installed VirtualBox with Vista as the host and 9.04 as the guest. Wired Ethernet works fine but it didn't seem to find my WLAN. What more do I need to do?
View 1 Replies
View Related
Feb 14, 2011
My net-book is working properly with Debian squeeze 2-6-32-5-686, only the wlan does not work. After typing lsusb I have got the message: lsusb : Bus 002 Device 002 : ID 160a:3184 VIA Technologies, Inc. VIA VNT-6656 [WiFi 802.11b/g USB Dongle]
So I obtained the driver package : VT6656_Linux_src_v1.19_12_x86. I followed the instructions ( make install... ) - but the result is only a lot of error messages. Mayby I am using the wrong driver package for the squeeze kernel - I don't know.
View 9 Replies
View Related
Apr 7, 2010
just click the [Computer] button at the left-bottom corner of the GNome desktop, the menu will shown, now press the printscreen button [PrtSc], nothing happen. no screenshot was made.or open any application , then click the menu like [file], let the menu list shown, then press [PrtSc] button, same thing, nothing happen.
View 8 Replies
View Related
Nov 7, 2010
I am trying to edit a postinfo.xsl in my root file dir, and with the command:
frank@linux-avnb:~> sudo gedit
(gedit:14150): Gtk-WARNING **: cannot open display: frank@linux-avnb:~>
I get the following. what am i doing wrong?
View 3 Replies
View Related
May 21, 2010
I installed squeeze and followed the instructions concerning b43-fwcutter and obtained firmware for my broadcom wlan interface. So my wlan worked for a while, but it just ceased functioning, for no obvious reason.
# lspci | grep WLAN
04:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
# dmesg | grep b43
[1.283080] b43-pci-bridge 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[1.283092] b43-pci-bridge 0000:04:00.0: setting latency timer to 64
code....
View 8 Replies
View Related
Mar 31, 2010
I just installed 9.10 on a brand new Dell Vostro 1520. The WLAN card does NOT work out of the box.
Here is what you have to do.
After install and rebooting insert the live CD
Go to software sources (system > software sources)and check the "officially supported restricted copyright" box
You are then asked to update the available software list, do so.
You will receive an error message since you are not (yet) connected to the internet and all the other repositories are not available.
Now you should be notified that restricted drivers are available, if not you can go to system > hardware. Anyway, now you should be able to activate the Broadcom STA driver. After rebooting you can connect to available wireless networks.
Alternative (in case you are not asked, which happened to me on another Vostro system) system>administration>syaptic package manager
Search for broadcom
Mark b43-fwcutter and bcmwl-kernel-sources for installation
Reboot (who said there is no rebooting required in linux)
The adapter should be up and running ...
View 4 Replies
View Related
Jul 23, 2011
Why doesn't encrypted WLAN communication work for me? I've got an HP Probook 6555b with Ubuntu 11.04 32-bit. When I set my WLAN router to unencrypted I'm able to connect. But if I choose WPA-PSK-TKIP or WPA2-AES or WPA-PSK & WPA2-PSK I can't connect. Ubuntu prompts me to enter my encryption key. I enter it. It runs for a while and then prompts me again. The little icon at the top right of the screen next to the speaker symbol is where I can see it trying to connect.
View 2 Replies
View Related
Sep 2, 2009
I have just updated KDENetwork to this level and now my F10 doesn't find any wifi connection. By the way, I have been working with F10 for some months without any problem on wlan.
iwconfig now says:
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
[code]...
View 1 Replies
View Related
May 26, 2011
i compile from broadcom wlan driver,when i use default F15 kernel (clean install F15)
Code:
$ uname -r
2.6.38.6-26.rc1.fc15.i686.PAE
[code]...
View 1 Replies
View Related
Jul 28, 2010
I have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
View 3 Replies
View Related
Feb 7, 2011
under 'System Settings < Keyboard & Mouse' I've already set the option 'Double click to open files and folders' but it doesn't seem to work with Dolphin.
View 4 Replies
View Related
Feb 7, 2011
I am using nx client and I would like to ask your help. Is it possible when I connect from home to my work's computer (using nx client) to see the exactly same desktop-taskbar and open programs as I left them in my work computer.
Imagine that you are at work using your computer. You lock the keyboard and you go home(you didn't turn it off). You go home and you login to work's computer. What I want to see is the same if I was just unlocking works's computer. IS that possible and how?
View 9 Replies
View Related
Jul 4, 2011
I set up opensuse 11.4. I updated nvidia 6600 drivers from vendor. Everything is good until automatic kernel update. When I start the system, opensuse is not open with this lines.
/etc/rc.status: line 1: /bin/ash : no such file or directory
bash: ./etc/sysconfig/chron : cannot execute binary file
X_MOUSE_CURSOR : Undefined variable
[code]....
View 3 Replies
View Related
Apr 11, 2010
The following message comes up when I boot up: Logging in user Warning: Cannot open ConsoleKit session: Unable to open session: Launch helper exited with unknown return code 0. When I press OK, the system completes the start up and everything looks normal. But when I try to connect to internet, I get the following message:
KNetworkManager cannot start because the installation is misconfigured. System DBUS policy does not allow it to provide user settings; contact your system administrator or distribution. KNetworkManager will not start automatically in future. If I reboot the system, I logg in successfully. So far the problem has appeared approximately upon every second time I boot up. Rebooting the system seems to take care of it.
Don't know what info is of interest. I'm using
Opensuse 11.2
KDE 4.4.2 (Factory)
After upgrade from 4.4.1 to 4.4.2 it worked fine for a week or so.
View 9 Replies
View Related
Sep 14, 2010
I just reinstalled my OpenSuse 11.3 with the GNOME desktop. As soon as I was done installing and I was on a fresh desktop, I installed the Yast updates that were available, rebooted, and now I can't login to any of my User accounts. Whenever I try to login, it tells me that it is "Unable to Open Session".o any of you know how I can fix this without having to reinstall all over again
View 1 Replies
View Related
Mar 6, 2011
I am trying to Install Open Suse 11.3 (burned as an ISO DVD) along with existing Win 2008 R2 OS. When I try to boot from the DVD it just logs in to Win2008 though boot from CD/DVD is enabled in the boot sequence. So i tried to mount the ISO and run from Windows ! BUT I get an error before installation starts telling that Win2008 R2 is not supported in open suse installer! Is there anything I can do to overcome this and install/retain both OS? In fact I am even trying to c hange my win2008 from R2 to Enterprise to see if I can overcome the problem!
View 9 Replies
View Related
Mar 22, 2011
I have installed OpenSuSE 11.4 on an HP DV6 laptop computer without problem. However when I boot the machine I get diagnostic messages immediately. First has anyone installed 11.4 on one of these HO machines? What diagnostic messages do you want to see to solve the problem?
View 3 Replies
View Related
Mar 16, 2011
I Have downloaded the ATI Drivers for my GPU From url.ymp But When I try to open the file This Message Appears :
This has happened After I Have Updated My Packages using
Code:
zypper update
View 3 Replies
View Related
Apr 11, 2010
yesterday i set my thinkpad t43p up with open suse, but i need to install my wlan...
i can't find the 12key big no to connect to my DSL telephone connection...
View 3 Replies
View Related
Apr 18, 2011
While it worked out of the box in 11.3, openSUSE 11.4 does not recognize my TP-Link TL-WN821N any more.
Googling a bit, apparently the old ar9170 driver is deprecated and supposedly a new driver carl9170 is integrated in the kernel now, but since it is not working this cannot be quite right.
Unfortunately, I do not understand much of the instructions given at the above two URLs: Should I try to install the old ar9170 driver? If so, I found older, pre-11.4 posts here that seem to indicate that is not so simple as just copying a firmware file somewhere, so how can I install it in openSUSE 11.4? Or should I rather try getting the new carl9170 to work? If so, how can I do this if it is already supposed to be part of the kernel?
The 11.3 Net-Install (from CD) recognised that USB-WLAN-Stick all by itself, installing 11.3 just fine through the air. With 11.4 it didn't work. So I borrowed a WLAN bridge for a couple of days and installed 11.4 now (32bit plain install plus Packman), but even after the install, plugging in that Stick does not do anything.
View 9 Replies
View Related
