I just installed version 11.4 on my system of a toshiba satellite l505d-es5025 64bit.My wlan will not show up at all.I installed ndiswrapper, and all of the wlan from yast.
View 2 RepliesI have just installed opensuse 11.3. I am absolutely new for Linux and for this forum. I have tried to open Network manager to configure my wlan. But its not starting. How to start network manager and configuring my wlan.
View 4 Replies View RelatedI have searched around a bit for a knetwork manager issue I am having on my opensuse 11.2 32 bit install. My wireless card is an 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) I am currently using the Broadcom wl driver
I am on the Internet with this machine as I am typing using the older "ifup" method. I am having great difficulty connecting to the Internet when I use knetwork manger though. The strange part is when I am connected to my router with knetwork manager, I can log into my Router, but I can not get to any web-page/ping any outside address.
so far the best (I was able to locate) advice I was able to get is located in this post. < Broadcom wireless, partchy internet - openSUSE Forums > following a posted how to to disable IPV6 (I suspect this may be the issue??), I was unable to locate modprobe.conf, or modprobe.conf.local, even after I updated via updatdb. I gave a shot at entering in "disable_ipv6=1" into "menu.lst". However, this did not solve my issue with knetwork manager. If my network information is needed when I am "connected" utilizing knetwork manager
I'm trying to search for more wireless networks but i cannot find a way to make network manager search for more wireless networks. It only displays 2 wireless networks and none of them is mine, even though I've got my wireless router at less than 1 meter from my PC.
View 2 Replies View RelatedI deleted all APs in my Wireless Section of network manager. After that, the whole network manager icon disappeared. I added the icon back on the panel, but I don't think its the right one. It doesn't do the two green cicles thing when I connect my ethernet wire in. It also doesn't show any wireless AP when I left click on the icon. It doesn't even have an X mark on the bottom left of the icon when no network is detected
View 1 Replies View RelatedI'm unable to get into my university's WLAN network. LAN works just fine, but sometimes it's quite convenient to be able to access stuff wirelessly. It doesn't seem to be a hardware problem, because if I configure my computer according to our computer department's instructions it works fine with Ubuntu (currently I carry around a stick to get into the Internet when I really need it and don't have a cable). Some info:
My device:
Broadcom WLAN controller on a Lenovo G560
My system:
OpenSUSE 11.3 64-bit
The drivers are installed, I can get into normal private networks, but have never managed to get into the university network except for with Ubuntu.
The university instructions tell me to use the following settings:
Security: WPA Enterprise
Authentification: TTLS
Inner Authentification: PAP
Username: My username
Password: Password
CA Certificate: Deutsche_Telekom_Root_CA_2.pem
In the KDE instructions, they tell you to write "anonymous" into the anonymous identity field, but in the GNOME instructions it says to leave it blank. In Ubuntu, I leave it blank and it works.
I've got the recommended settings, which also work in GNOME.
I'd ask the tech support here, but I am the tech support We've got it working with other systems, like I said, but not with SUSE, and I'm a SUSE fan.
i installed suse (KDE) on my old notebook and now I'm trying to get the wlan to connect to our router and can't figure out how to get it to work. My card seems to work, the network manager even finds the router, but i just cant get a connection. I followed the steps of the "Getting Your Wireless to Work" thread and these are the results:
[Code]....
- i messed around a bit with the network settings and might have cluelessly broken something (or broken it more)
- i tried a usb-wlan-card as an alternative, which didn't work either, but could possibly have messed things up even more.
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
I have a Broadcom B4312(I believe) wireless card and installed the drivers for it, but under the Wireless tab in Network Connections, it doesn't show "wlan0" or anything similar to "eth0"(which it shows under "Wired"). I ran iwconfig and this is what I got:
[Code]....
So decided to try a fresh install as ubuntu was having issues every update for me. Regardless i can't seem to get my wireless working and i'd really appreciate some help as i have no idea what i'm doing.
Using a hp pavilion dv5 1235dx.So my network card does show up it's a broadcom 4312 pci id 4315.Installed the b43 & wl drivers but it didn't help. The hardware switch is stuck at orange but in ubuntu it would function despite this(sometimes ).
I recently installed OpenSUSE 11.2 and everything works fine except wi-fi card, of course. The problem is that after installation the system recognized the card (is was listed in network devices in Yast) but I was unable to enable it through network-manager applet. Though the device could make scanning through terminal (found article in docs but didn't fully understand wpa_gui). Then i was stupid enough to delete the device from Yast list to try to reinstall it. So the problem is that i simply can't do this cause i see no way to re-detect. That is the goal is to at least turn back to post-install system state and try to enable wifi card again.
View 9 Replies View RelatedWhen I attempt to connect to a wireless network, the network manager asks me for the network's password, then says 'setting network address' for 20 or so seconds, then asks me for some random Hex or ASCII key in the same type of window I put the password in (Secrets for Noel -- KDE Daemon). Since a key is already typed into the window, I press OK, which then causes the network manager to go back to 'setting network address', then the window pops up again and keeps repeating itself.
I'm running Opensuse 11.4 with KDE, and my driver is ath9k. I don't know much about linux so please don't tell me to 'recompile this' or 'change this setting' without explaining how to do it. Please help, I've been unable to connect to wireless in OpenSUSE for 2 weeks now.
All settings are correct as far as i can tell. The wep key works on all my windows boxes. When i have connect automatically enabled it never tries to connect. if I go to edit it it pops kde wallet up i put in credentials. wallet goes away then nothing happens. if i double click connection to my router also nothing happens. I have the wep key in there and i even made it visible to make sure.
View 5 Replies View RelatedHaving a hard time getting NM to detect wireless usb device: Linksys model WUSB600N. Here are a few commands I do know about.
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
[code]....
Since a recent update on Stretch, I have been unable to use the network-manager to connect to my home wireless network on my laptop. It was working fine before. I did not change any settings on the WLAN router. I can still connect to other wireless networks at work and university, just not this particular one at home. All other non-Debian devices in my household are still able to connect just fine.While figuring this out, I have tried connecting manualy with ifup but I don't really know how that works. Right now there is only the loopback entry in /etc/network/interfaces.
Below is the output of syslog, when gnomes network-manager is trying to connect, but fails.
Code: Select allJul 19 20:01:57 debian NetworkManager[6705]: <info> (wlan0): Activation: starting connection 'Affenbande'
Jul 19 20:01:57 debian NetworkManager[6705]: <info> (wlan0): Activation: Stage 1 of 5 (Device Prepare) scheduled...
Jul 19 20:01:57 debian NetworkManager[6705]: <info> (wlan0): Activation: Stage 1 of 5 (Device Prepare) started...
[code]...
My Dell Vostro 1520's Dell Wireless 1397 WLAN Mini-Card must not have been set-up correctly, as the Network Manager won't even let me select the wireless tab. Please just explain to me, step by step, what exactly I must do to make it work! Additionally, I can't figure out how to disable my Touchpad's Tap to Click funtionality, which must be done if I'm to effectively use my current KDE installation of openSUSE
View 9 Replies View RelatedI am using an HP laptop dv8000 series FYI. I started with a fresh install of OS11.2. The first thing I tried was to connect to a network through the gui net manager. This got me nowhere (nothing detected). I then noted that the card was not getting any signal/not functioning. My card is enabled from on the laptop.
I connected my laptop via ethernet and executed this command:
Code:
sudo /usr/sbin/install_bcm43xx_firmware
which returned no errors and seems to have completed successfully.
Using the dmesg | grep firmware command I now get the following:
Code:
SuSE-Laptop:~ # dmesg | grep firmware
[41.246079] b43 ssb0:0: firmware: requesting b43/ucode5.fw
[41.268643] b43 ssb0:0: firmware: requesting b43/pcm5.fw
[41.320790] b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
[41.369098] b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
[41.591065] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
SuSE-Laptop:~ #
Now the option to enable wireless in my systray (I know wrong name) has become unselectable. Now what do I do?
I recently installed 11.3, I was able to get my wireless working. However only using the "traditional method with ifup", I could not connect with network manager. I remembered last time I installed 11.2, it was suggested that the wired connection was taking precedence, which was the initial reason I went the traditional route. I changed the wired connection to "on cable connection" and the wireless to "boot time" but still no luck. So are both methods fine and its just a matter of preference, I would prefer to use knetwork manager.
View 2 Replies View RelatedThis is a brand new install of 11.4. While trying to set u p for wireless, when I click on network manager it does not open. Do I need to re-install? I am using a Toshiba Satellite , dual booting with XP. The install was seamless, and picked up all my files from the previous distro. Now the big bugaboo, wireless, but I can't seem to get oout of the starting gate if I can't get to network manager?
View 2 Replies View RelatedHow do you install network manager in LXDE. I need to choose from a list of available wireless networks.
View 2 Replies View RelatedI have a rtl8192e card and the drivers and everything are set up properly. I can not connect to WEP encrypted networks using network manager. I can however connect using iwconfig and dhcpcd. I uninstalled network manager and installed WICD and have the same problem. It will connect to the access point when it is configured with WPA, but not WEP which we need to use for the other computer. In the status bar of WICD it looks like it is trying to configure the encryption as WPA no matter what I select. I've looked in the config files for WICD and can't see anything that would do it.
View 3 Replies View RelatedEvery single time I enter the network manager to edit connections is crashes on exit. I am running opensuse on an Asus eee PC 1000HE with an Atheros network card. The crash report follows :
Distribution: openSUSE 11.2 (i586)
Gnome Release: 2.28.2 (null) (SUSE)
BugBuddy Version: 2.28.0
System: Linux 2.6.31.12-0.2-default #1 SMP 2010-03-16 21:25:39 +0100 i686
[code]....
As an extra point. I wish I could disconnect individual networks instead of just disabling networking to disconnect. I think the newer version of the network manager does this.
I have an Atheros ar5007eg wireless card, and I haven't had problems with this card in GNOME. However, when I made the switch to KDE recently, I can't connect to any wireless networks. A wired connection works fine (that's how I'm writing this), but when I try to connect to any wireless network, it hangs at Acquiring IP Address, then asks me for my WEP key again, I enter it, and the process starts over. I tried using WICD, but I'm not sure if I set it up properly.
View 2 Replies View RelatedInstalled openSUSE 11.3 over an existing 'very stable' 11.2 installation and started experiencing wireless connectivity issues immediately. Network Manager would show connected 100% - 92% but I would lose connectivity to mail, browser and messenger(s). This disconnect would last less than 30 secs but would occur every 2 to 4 minutes.
dmesg reported:
[ 3663.672098] iwl3945 0000:03:00.0: Failed to get channel info for channel 3 [1]
[ 3664.101085] iwl3945 0000:03:00.0: Failed to get channel info for channel 3 [1]
[ 3664.529050] iwl3945 0000:03:00.0: Failed to get channel info for channel 3 [1]
BTW Channel 3 is the channel my wifi is broadcasting on. I've tried other channels and other computers and it is only openSUSE 11.3 having an issue. I am also using WPA2. Modifying the Global Options in Network Settings from User Controlled with NetworkManager to Traditional Method with ifup seemed to stabilize most of the issues, but I do notice occasional drops. I've also switched from Network Manager to wicd to provide some UI while dealing with this issue. Since iwl3945 drivers are now in the kernel I don't know if I should try to revert to an older driver or if there is another issue.
I just installed OpenSuSE 11.3 on an old IBM T20 I had kicking around and I'm using a Proxim Wireless PCMCIA Card (Atheros AR5001X). Since this laptop does not have a DVD drive I installed the system using the Netboot CD and have the SuSE 11.3 ISO on an NFS/SAMBA file server. The issues appeared after the first reboot, the adapter no longer worked. I resorted to using the wired interface to finish the install.
Once the system was up followed the trouble shooting steps outlined in various places and found the ESSID is not being picked up by the ifup scripts. Not sure if it matters but I have ESSID broadcasts turned off on all my WAPs.
The ESSID is in ifcfg-wlan0. To get wireless working I have to manually issue iwconfig wlan0 essid "xxxx"..
Both networkmanager and ifup fail..
My wireless device is an integrated Dell Wireless 1397 WLAN Mini-Card, I am unsure about the driver I have in use. I am sure I have a driver installed because the configuration screen shows my network. I currently have the computer plugged into my network via CAT 5 but I would like to be able to use the wireless (obviously.) I am using Open SuSE version 11.2 and I have run the updater. I could not see my wireless network before running the updater and I can now so I know that the updates have helped but I am again stuck. I have tried to search the wireless forum and I have tried to tinker with the settings in YaST , but nothing seems to be working. Reading the Welcome page of the wireless forum, I tried the Broadcom chip-set advice:
[Code]...
I have read and taken to heart the advice given for receiving help and if any more is needed I will gladly give it. I have a small amount of experience with SuSE Enterprise edition so I can understand some technical stuff but I am best at following specific instructions.
I have just installed openSuse 11.4 KDE 64-bit on a Dell M1330. When I click on my networking panel, it says WLAN interface is unavailable. I've followed the steps in the stickied post and found the WLAN hardware info, a screenshot of which is below:Uploaded with ImageShack.usNext it says to do this - you need to look at the logs, in particular the info in /var/log/boot.msg. To see this, you need YaST => Miscellaneous => System Logs and select boot.msg.In YaST there is no such option for system logs under miscellaneous, so I can't do that. The results of the sudo /usr/sbin/iwlist scan command produce the following:
root's password:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
I have a minor problem with Knetwork-manager. When I boot up, it won't connect to my wireless router automatically. I have to right-click the taskbar icon, disable wireless, then enable wireless, then it connects fine.It remembers the password fine and once it's connected, it's flawless. It's just the minor issue of having to effectively 'switch the internet on' rather than it just being connected when I turn on my laptop.
I'm using Opensuse 11.2, KDE 4.3.1 (didn't have this issue with 11.1). I've tried the latest Kubuntu (9.10) and knetwork-manager worked flawlessly but I didn't like the rest of the OS so I came back to Opensuse If I restart, suspend or hibernate it usually connects okay, it just seems to be when I boot from 'cold'.
I've tried nm-applet but same problem. I also tried wicd but it didn't really like my system. I've changed my wireless router recently as well with no change, so I don't think it's that. As I say it's a minor problem, it's not really an issue for me to turn it on each time but it would be nice to clear it up. I've googled and searched since 11.2 was released but haven't found any answers and my linux skills are still a bit lacking.
Am all of 2 days old on Opensuse 11.0 having just installed it on my old PC. All my experience has been with XP/Vista and Macs and it took some courage to finally try this out. My Belkin F5D9050 wireless(g+ MIMO) usb network card is recognised in yast but does not connect to the internet. On reading through forums I understand that this adaptor uses RAlinks RT73 chipset and support for should already be available in the OS. Is this correct ? If not, where do I get the driver for this and how do I install this. As per the Belkin site, Opensuse driver support isnt listed. Am struggling due to the unfamiliar environment and am not aware of terminal commands.
View 1 Replies View Relatedso far i testet 4 wlan cards (prism, ?zytel?, realtek and another realtek) they all work without a problem with kubuntu. but with ubuntu they dont want to build up a connection to my router. it looks like the passphrase is wrong..he asks me after a short time to reenter the phrase. but the phrase isnt wrong(copy pasted) the phrase has some special characters but only '=' and a few '!'. so i doubt that that could be the problem im pretty sure there are more people out there who have the same problem. I hope someone knows a solution :/
edit: i did some searching and found this... seems to be a major problem[URL]...