I've just got a TP-Link wn-851n PCI WLAN card, and the problem is that ubuntu can search for the network, but I can't join into the network after typing the password. I'm sure that it is correct as m Windows notebook is also using that network.
Taking a look in dmesg, and it start to loop this message after I joined the network.
Quote:
I have a desktop that has a d-link DWL-520 wireless card, which was working under Windoze. Today I installed Centos 5.4 on the system , which went cleanly. I then used Network Configuration to set up the wireless card. I specified to use DHCP, set the SSID and authentication password. When I tried to activate the card I get these error messages
Error for wireless request "Set Mode" (8B06): SET failed on device wlan0 ; Operation not supported. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0.
The hardware manager seems to have correctly identified the card and chipset, (Intersil Prism 2.5) and installed driver hostap_pci which came with the distro. This web site seems to suggest that this is the correct driver: [URL] searching forums I've found a few references to these errors, but they were from several years ago, and for different distros and cards. I did find a reference to using Network Manager to configure the card instead of Network Configuration. I started the NM service and configured a connection using it instead, but still no luck.
[Code]....
Could anybody confirm that the D-LINK DWA-556 wireless N PCI-E network card works with Lucid Lynx 64 bit? Im looking for a reliable wireless network card that if possible works out of the box on Lucid 64 bit, so far my search has lead me to the above card, If anyone has hands on experience of this card on lucid 64
View 2 Replies View RelatedAfter connecting to any host, the openssh client hangs after I type the password. The strange part is, it only hangs if when I use the wlan card. If I connect my phone to the computer and uses it to connect to my server, it works 100%.
If I use any other computer at the wireless network, it works 100%
If I use putty on the same machine, it works 100%
It is only a problem when I use the build-in wireless card, under openSuSE 11.3, on my Lenovo L512. (note that everything besides ssh works completely).
I have just installed Ubuntu 9.10 on an Acer TravelMate 290E. I've got internet connection through the Ehternet Cable, but when I plug in the D-Link WLAN USB device, although the system recognises it, it is disconnected. How can I connect the WLAN USB device adn get it to work?
View 5 Replies View Relatedi installed suse (KDE) on my old notebook and now I'm trying to get the wlan to connect to our router and can't figure out how to get it to work. My card seems to work, the network manager even finds the router, but i just cant get a connection. I followed the steps of the "Getting Your Wireless to Work" thread and these are the results:
[Code]....
- i messed around a bit with the network settings and might have cluelessly broken something (or broken it more)
- i tried a usb-wlan-card as an alternative, which didn't work either, but could possibly have messed things up even more.
I'm really new to Linux so this will probably sound like a pretty naive question to most users, but how do you change the root password?To install Java, I have to type # su into Terminal,which then asks for the password.What's weird is that when I start typing a password, no characters show up. I don't know if this is supposed to happen or not.I've found a bunch of different sites on the Internet that explain how to change the root password, but none of them seem to work for my specific work station.
I've got Ubuntu 9.10 64 bit. In the GRUB boot menu, I can choose to boot normal or in recovery mode (I'm led to believe older versions don't have this option).I've tried typing # sudo passwrd into Terminal, but I already have a root password set up apparently, so I can't change it there.
specific Ubuntu supported WLAN PCI-cards? This link shows a list of supported PCI-cards, but which is best: [URL] And the installation needs to be easy! I�ve tried installing these PCI-cards in my computer, useing Linux drivers, NdisWrapper, etc. Unforutately without any success:
- DWL-G510, Ralink Chipset, Ralink RT2561/RT61
- Realtek Semiconductor, RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller
I have bought a new laptop with win7 on it , I delete win7 and install ubuntu64 everything is ok but my wireless card won't work ( it is recognized) and even I can connect to INTERNET but nothing is download or upload so I have bought another usb wireless card but now when I connect this new card to my laptop it still tries to use the old one and so I could not connect to internet
View 4 Replies View RelatedI'm a new user of Ubuntu and I think I need some help but let me mention before that I got this up working on a Debian system.My current kernel version is $ uname -r 2.6.32-27-generic.The problem is that my wlan card is not working any more such that my system freezes every time I enable networking with the hardware switch on my laptop.Therefore I bought a USB - WLAN stick and try to get this working.
Network Manager has the option "enable wireless" greyed out if I disable the hardware switch.If I enable the hardware switch and remove the module of my wlan CARD before (modprobe -r iwl3945) it says "wireless disconnected" for all networks.
Am having intermittent connectivity issues with my stock Atheros AR5212 on my Thinkpad X61 using Ubuntu 10.04. Am wondering if there is a known to be good b/g min-PCIe card that I can replace my AR5212 with that would be more solid in Ubuntu?
View 2 Replies View RelatedI have been using FC10, it works well with wlan for sometime and goes inactive after some time and hence network goes unavailable. Even after few attempts to reconnect doesn't help. Rebooting helps in bringing it back temporarily.
View 7 Replies View RelatedI have 2 wlan cards. wlan0 and wlan1. wlan0 is in AP mode(Master mode) using hostap. wlan1 is connected to another wireless network and is in Managed mode. Now I want to make a bridge between wlan0 and wlan1. I do it like that:
ifconfig wlan0 0.0.0.0
ifconfig wlan1 0.0.0.0
brctl addbr mybridge
brctl addif mybridge wlan1
can't add wlan1 to bridge mybridge: Operation not supported
It doesnt work, because wlan1 is in managed mode. But Windows 7 can bridge 2 Wlan cards when one is AP and another one is STA. How to do it in Linux?
I upgraded Ubuntu to 11.04 I can NO longer connect wirelessly using my BCM4312 WLAN Card. It connected with no problems before dist upgrade using Ubuntu 10.04. Im really not sure why I cannot connect. I cannot even see my router in edit wireless connections settings. I can however see my neighbours routers who are using WPA2 encryption. But I cannot see my router.
I have uninstalled and reinstalled The Broadcom STA proprietry wireless driver several times using Additional drivers. This did not fix my issue.
I am connected by ethernet at the moment so I do have internet connection.
I'm trying to join a wireles lab that I've setup with WEP encryption, but I'm unable to join. (I've tried on two different distros: ubuntu, and backtrack) same result.
here are the commands:
Code:
ifconfig wlan0 down
iwconfig wlan0 mode managed
iwconfig wlan0 essid MYNET
iwconfig wlan0 key XXXXXXXX
iwconfig wlan0 channel 3
dhclient wlan0
tries to contact dhcp but none responde to request, and when I do iwconfig, it shows as not associated
I'm having trouble setting up new Alix URL... system with a wireless card. I got the card from an old working Buffalo AirStation router. The card is a WLI-MPCI-G54 and is using Broadcom BCM4306 chip. I've installed Debian on the system.My goal is to make a wireless access point by using hostapd authentication service. I thought it might be a good idea to verify that the wlan-card is working properly first, but it can't seem to detect my local wlan.
View 1 Replies View RelatedI have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
I'm using Ubuntu 9.10 on a Lenovo ThinkPad T61 using an Intel PRO/Wireless 3945ABG. My laptop's ability to connect to a wireless network stopped last night, and I'm not sure why. It's definitely something on my end, as my roommate can connect to the internet on a Windows box. I can wire in without a problem, but that's a pain and my Ethernet cable got lost in the shuffle when I moved back to school. I've been able to get into this network before and nothing about it has changed. I've been able to hibernate and restart and such and nothing has ever needed to be reset.
The router's a D-Link WBR-2310. Wicd and Network Manager see the network (I'm back to using wicd) , but wicd appears to get stuck at "Obtaining IP address..." and says "Unable to connect: Cannot obtain IP address". I know my password is correct (I set up the router and I'm the CS undergrad in the apartment so I manage it), lspci sees the wireless card, ifconfig and iwconfig return information about the interface, dmesg|grep wlan0 doesn't seem to have anything terribly out of the ordinary, but here's that output:
Code:
allyanncah@taliesin:~% dmesg | grep wlan0
[ 23.514202] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.609016] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 38.756143] wlan0: direct probe to AP 00:24:01:cb:4e:7e (try 1)
[ 38.758791] wlan0: direct probe responded
[ 38.758796] wlan0: authenticate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.760587] wlan0: authenticated
[ 38.760609] wlan0: associate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.763318] wlan0: RX AssocResp from 00:24:01:cb:4e:7e (capab=0x431 status=0 aid=1)
[ 38.763322] wlan0: associated
[ 38.765502] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready .....
I've tried:
- reinstalling wicd
- uninstalling wicd and installing network-manager
- restarting
- shutting down and booting back up
- restarting the router
- sudo /etc/init.d/networking restart
- taking the interface down and back up with ifconfig
I haven't changed anything recently in regards to my wireless card, and all the fixes I've tried are things I've done before without an issue. The only thing I'm wondering about is if doing a hard reset might have broken something (I know this is a cardinal sin, but there's a whole 'nother problem I haven't been able to fix with the OS hanging every once in a while over a VPN daemon when it tries to shut down or restart -- I've left it for hours to see if it actually gets anywhere and no luck, won't do a soft reset). I'm nervous about reinstalling the driver just because I've never had to do it and drivers are a finicky business. I imagine there's a config error somewhere?
I have a TP-Link WN851n ver2 with the ar922x chip. This just seems to drop out. it sometimes connects but not reliable. It is just plain annoying. I have to run windows to get any wifi to work properly.
View 1 Replies View RelatedI have a Dell Inspiron 1525 laptop using Dell Wireless 1395 WLAN Mini-card (This is what Windows Vista says I have). I have installed Ubuntu as dual boot with existing Windows Vista. Wireless is not working in Ubuntu but working flawlessly in Windows.
Here is the output using CODE: lspci.
hai@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
02:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
02:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12)
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
hai@ubuntu:~$
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
I have a Dell Latitude D800 with a Dell Wireless 1350 (802.11b/g) WLAN miniPCI Card. I need to install wireless on this laptop but I see no wireless card when I know I have the above wireless card. Here are some commands that I ran that I might prove useful:
[Code]....
Inspiron 1525 - Wireless 1395 WLAN Mini-Card I passed two days browsing the net looking for a solution to my problem but no way.. Im running ubuntu 10.10 in my inspiron via VirtualBox and my wireless card is not detected by ubuntu.. I installed the bcmwl6.inf driver with the wrapper and it show me in wireless window that the hardware is not present.. So checked that in the terminal by typing :
Code:
lshw -C network
*-network
description: Ethernet interface
product: 82540EM Gigabit Ethernet Controller
[Code].
My Dell Vostro 1520's Dell Wireless 1397 WLAN Mini-Card must not have been set-up correctly, as the Network Manager won't even let me select the wireless tab. Please just explain to me, step by step, what exactly I must do to make it work! Additionally, I can't figure out how to disable my Touchpad's Tap to Click funtionality, which must be done if I'm to effectively use my current KDE installation of openSUSE
View 9 Replies View RelatedI have a D-Link Air DWL-520 wireless card on my desktop computer. It runs well with Windows, but doesn't seem to work with Ubuntu. I am using Lucid Beta 2. I have tried googling, but have not come across any clear solutions on how to make it work.
View 1 Replies View RelatedUbuntu 10.4 with wireless card TP-Link TL-WN321G the driver installed and it connect to the wireless network but no internet access. I checked everything about the wireless information and everything is fine nothing wrong and the ip address is fine, am new to ubuntu and I don't know how to uninstall or reinstall the driver so I bought another wireless adapter Xtech this one the ubuntu didn't recognize it and I have the cd it came with but the driver is like make file and configure and .a or .c I really want to use ubuntu but without an internet connection no use of it!
View 1 Replies View RelatedI bought an USB-WLAN stick, which does not recognize any network. A Ralink 802.11 bg WLAN Stick works fine, but the Ralink 802.11 n WLAN Stick does not work unfortunately. Both get recognized by the nm-applet of network manager but only the first one recognizes my network and is able to connect to it.
[Code]....
recently I risked a look to the Linux world and I'm happy so far, but now I've got a Problem, I'm unable to solve by myself. I installed Mint (Julia) on my old Laptop to test Linux. The Laptop has a very old PCMCIA WLAN Card with a Realtek rtl8180 chipset. Everything seems to run perfectly so far with one exception: the WLAN doesn't find any Network to connect although the card and the driver seem to be installed correctly.
Here some code from the terminal:
Code:
lspci
00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M]
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:03.0 Modem: ALi Corporation M5457 AC'97 Modem Controller
[Code]...
very much like everybody i am also waiting for centos 5.3, because 5.2 could not sit on my notebook due to obvious driver issues. would anybody tell if centos 5.3 support my x3100 graphics card and bcm 4311 wlan card?
View 5 Replies View RelatedI had Ubuntu 8.04 and the D-Link Wireless WNA-1330 PCMCIA card worked just fine. I upgraded to 10.04 and it fails. I can see the network of wireless routers in my neighborhood, but when I try to connect on WEP 40/128bit with my hex key of my router, it tries to connect but can't get a DHCP address. I cannot ping the router in that state, of course. I have two other 10.04 laptops (with built-in wireless) and they connect just fine, as does a Windows Vista laptop. I also tried the pci=noapi item in /boot/grub/menu.lst, but that failed to show any results either. The card lights up like it should, and acts just like it did with 8.04 on the lights, but it doesn't connect. I end up seeing the "Enter your WEP password" dialog again and again unless I hit Cancel.
View 1 Replies View Related