OpenSUSE Install :: Unable To Boot Into The OS - Error 25 GRUB Stage 1.5 ?
Jul 31, 2009
A few days ago I decided to ditch Windows for good. I read for hours about a Linux distro and settled on OpenSUSE.
I just need to say one thing. Linux is not for the feint of heart, and everywhere I turn (forums), I see computers riddled with error messages, frustrated people, and the list goes on.
I'm willing to work through this though since I feel that the benefits will outweigh anything that Microsoft can offer, so here goes.
Upon installing the new build of OpenSUSE, I encountered an error message that was fixed by hitting retry (I forgot the name, but I remember it being something like Etk3 or something of the sort).
My issue now is not being able to boot into the OS. I'm getting Error 25 from GRUB on stage 1.5
I've installed 11.1 over my Windows XP partition. I want XP no more. Additionally, I read the sticky and followed all the instructions. I also selected the KDE desktop (I still don't know the difference between that and GNOME despite Googling it several times).
View 9 Replies
ADVERTISEMENT
Jun 13, 2010
I installed opensuse 11.2 64bit on my external hard drive with the idea that this way the two OS would be completely seperate and I could just use suse when I felt like it. Everything boots fine for both OS when the hard driv is plugged in but when it is unplugged I can't get past a boot screen which says: Grub loading stage 1.5 Error 21 I have seen on another forum a fix using the windows install disk but I no longer have this. Is there some other fix I can use to make my laptop portable again.
View 9 Replies
View Related
May 2, 2011
Every time I start my computer, I get a message saying:
I press any key, and the start-up completes without further problems. The first line on the screen after I press any key is
I`ve looked on the web, and grub stage 1.5 seems to be where the size of the hard drive is identified. Problems often seem to be linked to partitioning. My hard drive has (since new) a 115GB and a 5GB partition.
When I try to access the 5GB partition, I get the following error message:
Linux 2.6.34-12-desktop i686
System: openSUSE 11.3 (i586)
KDE: 4.4.4 (KDE 4.4.4) "release 2"
View 2 Replies
View Related
Aug 22, 2011
I just installed LXDE by pluging the P-ATA drive into my current PC (with my 2 S-ATA drives being plugged in). Not worked first time, probably because I pushed the drive too hard into the old PC. Formatted again, installed LXDE again (this time my S-ATA drives plugged out). Works fine with the old PC, but when I try booting from my current PC now it says: "Grub loading stage 1.5 ... Grub Error 21". No menu, nothing ... And because I plugged my S-ATA drives out, when installing LXDE the second time, the config file, grub is probably searching for on the P-ATA drive, is somewhere in nowhere. Googled it 2 hours ... Yast2 Bootloader and grub-install are just trolling me. The drive I installed LXDE (32-bit) on, is an old P-ATA, with first 30 GB, then suddenly 80 GB (don't ask, I don't know either. First formatting was 500 MB swap and the rest Ext4. Second formatting was 1011 MB swap and the rest Ext4.
View 2 Replies
View Related
Jul 28, 2011
A few days ago I installed openSUSE 11.4 on a 1TB HP external hard drive. I have some very important files for school and personal work on my main hard drive, running windows 7, so I made sure the installation only affected my external hard drive. With the external hard drive plugged in it boots just fine but when it is un-plugged it says Grub loading stage 1.5. Error 21 and it won't do anything. This kind of pisses me off because there were no warnings and nothing was supposed to happen to my main hard drive. But this has already happened and now I want to know if there is any way I could fix it so I can boot windows 7 normally and still boot openSUSE with the external hard drive plugged in.
View 6 Replies
View Related
Jun 10, 2010
I have the computer hooked up to a TV via HDMI. The resolution of the booting process is set to 1280x720, and then KDM goes to the correct 1360x768.
Sometimes when I boot, the TV does not receive a signal until the boot stage reaches the KDM. I do not know how to reproduce this exactly.
View 3 Replies
View Related
Jul 10, 2010
ok so i jut installed ubuntu from an old live cd, i had to upgrade it twice to get it currant, and i also have a win 7 os on my box. Now when I try to boot I only get as far as the grub loading screen where an error 17 pops up, google says thats because it can't boot the selected boot partition but i cant even select my windows partition. im on the old live disk right now.
Here's a screenshot of a sudo fdisk -l command [url]
View 9 Replies
View Related
Aug 18, 2010
Dual Booting my laptop and unable to change the Boot Records on the drive. Not because I dont know how, but my primary OS will fail to boot(win7).
I have drive partitioned as follows...
sda1 = Win7 system (default install)
sda2 = Win7 Main (default install)
sda3 = swap
sda4 = Extension (I think thats what its called)
sda5 = / (ext4)
What I need is a boot cd or perferably Grub installed on a 256MB Thumb drive with the options to load the installed system from sda5.
View 4 Replies
View Related
Mar 27, 2010
My laptop is running Fedora 12. I installed BackTrack 4 onto an external USB hard drive using a LiveCD. Now when I boot my laptop. I get this: GRUB Loading stage1.5. GRUB loading, wait Error 21. I never touched anything with my internal drive. When I was reviewing what partitions the installer was going to format, the swap partition for my internal drive (Fedora) was set to be formatted even though I did not specify this. Fedora never used to show GRUB loading at all. Screen was blank until Fedora starting loading. Maybe this means that this is a copy of GRUB from my BackTrack disc? I ran 'fdisk' to look for anything suspicious and under /dev/sda1 (internal drive, boot partition) it says "Partition 1 does not end on cylinder boundary."
View 9 Replies
View Related
Jul 8, 2011
I am new to Linux. I have installed RHEL 5.4 on my PC with preloaded Windows XP.
Windows was set as the first boot kernel. So if i do not choose which OS to be loaded it will load Windows by Default.
Today I got an error saying GRub Loading Stage2 read error.
View 9 Replies
View Related
Jun 11, 2010
I have installed latest kubuntu (10.04) on sda7, ext4 , and i selected the advanced feature of the installer to install kubuntu bootloader on sda7. 11.1 is on sda5 .First , it destroyed my 11.1 grub bootloader on mbr . I managed to restore it with the 11.1 installation DVD. Now i try to boot kubuntu from the sda7 bootloader, without success . I searched the forums and tried some hints i found but found no similar problems. Here are the different entries i tried on grub (mbr) , content of the /boot/grub/menu.lst :
Code:
# Modified by YaST2. Last modification on ven. juin 11 15:41:32 CEST 2010
default 0
timeout 3
gfxmenu (hd0,4)/boot/message
##YaST - activate
[Code]...
View 9 Replies
View Related
Nov 4, 2010
I was messing with some boot loaders which accidently disabled grub and I was remained with windows 7 boot loader only.How can I restore grub?I am using Opensuse 11.3
View 8 Replies
View Related
Jul 20, 2010
I started my laptop this morning with no problems. It was doing a file system check which I quit (pressing C) after about 30%. The only problem I had was wired networking didn't seem to be working (though wireless was). No problem: this happens sometimes and a restart fixes it. After restart: the GRUB screen hangs at "Loading stage 1.5" for ages before issuing Error 25. Try a restart. Same thing. And again. I'm on Lucid 10.4, no other OS installed, Toshiba laptop that up to now has had no problems with the last two versions of Ubuntu.
View 1 Replies
View Related
Dec 22, 2010
I've installed FreeBSD (sdc1) and DesktopBSD (sdc4). When I try to boot DesktopBSD it boots FreeBSD.here is menu.lst
###Don't change this comment - YaST2 identifier: Original name: other###
title FreeBSD 8.1
rootnoverify (hd2,0)
chainloader +1
###Don't change this comment - YaST2 identifier: Original name: other###
title DesktopBSD-1.7-amd64
[Code]...
I guess the chainloader boots 1st ufs slice and ignores the other. I've installed GrUB in FreeBSD and when I try to boot with different menu 'configfile /boot/grub/menu.lst' it returns error 17. This is probably due to inability reading ufs.
View 9 Replies
View Related
Jan 6, 2010
I'm trying to install ubuntu from a CD. I believe it is version 8.4 The install seemed to go fine and I rebooted my computer and immediatly after start up I get a message that says: Grub Loading stage 1.5.
Grub loading, please wait... Error 18
I have no idea what this means or what to do and Im not the most computer savy guy. My computer is stuck and will do nothing at this point.
View 3 Replies
View Related
May 28, 2010
I reinstalled Mac OSX and my Mac files on my 24" intel core 2 duo iMac from a Time Machine backup. The Linux and Swap partitions appear to be unaffected. However, rebooting into Linux 8.04 stops at the Grub stage.
View 7 Replies
View Related
Apr 27, 2011
I did a fresh install of SuSE 11.4 (WIN7 TOO) and changed my Larger HD1 to the first HD. I was installing and got this error first: the boot loader is installed on a partition that does not lie entirely below 128GB The system might not boot if BIOS supports only lba24 (result is error during install grub mbr) status loc dev/sdb6
I continued with the install and then got:
Yast2 error occured
while installing GRUB ver 0.97 (640k lower/3072k upper memory)
[minimal bash-like lineediting is supported? for the first word, TAB lists possible command completition anywhere else TAB lists possible completion of a device/filename]
grub setup --stage2=/boot/grub/stage2 --force4-lba (hd0,5) (hd0,5)
Error 25
disk read error
grub> quit
View 9 Replies
View Related
Apr 30, 2011
I resized my windows c drive to make another drive which also has Open SUSE 11.4 dual booting which was working fine.
After reboot I get missing operating system so I boot the live Opensuse DVD and the windows and Linux is still there so I tried the boot configure tool in YAST but get the error because of partitioning the boot loader cannot be installed properly
Can I make a boot floppy somehow? I now have a grub menu when it boot sup but do not know what to do now
View 9 Replies
View Related
Apr 28, 2011
A few days ago I went to perform the Service Pack 1 Upgrade for Win 7. This crashed out with an error. On researching the problem I found a solution to fix the problem by marking the Windows partition as active. I did this (via Computer Mgmt -> Disk Mgmt). This allowed the SP1 upgrade to work, however on reboot I got an error BOOTMGR missing. This I rather rashly resolved by using the Windows 7 install DVD in Recovery mode to reinstall the Windows Boot manager via bootrec /Fixboot I thought I would then be able to use the Opensuse 11.2 install disk to fix grub.
I use the Opensuse install disk and select Repair system -> Expert Mode -> Install New Boot Loader then select Other -> Reread Configuration from Disk. This adds Win 7 back into the grub menu. I then select OK and get the message "the bootloader was installed successfully". The problem then comes when I click my way through OK and Next to finish the install. At the end of the process I get the message "An error occurred during the installation" and I'm no further forward.
FYI the PC has a single SATA disk installed partitioned as follows:
dev/sda1 100Mb Win System Parkition
dev/sda2 Windows NTFS
dev/sda3 Windows FAT
View 8 Replies
View Related
Jun 29, 2011
I have a single boot system that was working great until this morning when it locked up. I was working as I always do when the system stopped responding completely. CTRL+F1 did not work to allow me into the back so I could log in and see what was happening.
CTRL+SHIFT+SysRq did not recover the system or interrupt what ever was causing the lock up.
SSH from another system failed as the client did not respond
So I had to do a hard boot and when I did I got this:
GRUB Loading stage1.5.
GRUB loading, please wait...
Error 17
Again this is a single boot system no Windows other than in VMWare inside the install. It is a multi drive with RAID set up workstation that I have at work. The short of it I am sole IT support as our companies ITS will not support Linux. In 5 years of operations with Linux at work this is my first issue, and I can't figure it out. I already tried the PartedMagic solution (ref = Re-Install Grub Quickly with Parted Magic) and that didn't work.
I re-installed the system completely even going to the extent to change my partition scheme just to make sure that wasn't the problem (which doesn't make sense as the system had been running for 46 days non-stop without a problem). Upon reboot after performing a complete security update I got the Error 17 message again.
Below is the output of fdisk -l
Code:
Welcome - Parted Magic (Linux 2.6.30.6-pmagic)
Most of the filesystem tools and partition programs featured by Parted Magic include man pages. To read a manual page, simply type man and the name of the tool. (Examples: 'man ntfsprogs' or 'man fdisk')
[Code].....
View 9 Replies
View Related
Feb 6, 2010
not sure what happened, yesterday i installed the new kernel and played around a bit by uninstalling some older kernels. Everything was fine but now i cant boot into ubuntu any more. I have a Dual boot and Grub let me boot into windows. for linux grub gave error 17 (if i remember correctly).o i popped in the LiveCD and tryed gparted to check for errors (nothing changed). I tried rewriting grub from the live cd and that made matters worse.
Code:
grub> find /boot/grub/stage1
find /boot/grub/stage1
[code]....
View 3 Replies
View Related
Aug 4, 2010
I'm trying to install Debian Lenny on my new Dell XPS 8100 Desktop with 2 x 1To SATA HD. (No Windows or any other OS install is present on the system) The Bios allows me to change the SATA mode to either "ATA" or "RAID"
- When SATA mode is set to RAID, the installation goes without issues, but when it comes to load into the system, I've got that Stage 1.5 Grub Loading... Error 2 problem. I assume this is due to the Bios "RAID" configuration. I then switched the SATA mode to "ATA" in the Bios and now I can see the menu that allows me to boot my debian install but that part actually fails too saying "ALERT /dev/sda1 does not exist"
- When SATA mode was set to ATA, I tried to re-install the system but this time my drive was not recognized by the installer: "No common CD ROM drive"
View 2 Replies
View Related
Sep 2, 2009
I installed windows and haven't been able to boot to fedora since. Without a boot disk my machine complains 'BOOTMGR is missing'. If I use a boot disk to access grub on another linux partition (/dev/sda5) I can try to boot my fedora install using its old grub.conf settings. However this gives me the grub error:
Code:
root (hd0,0)
Filesystem type is ext2fs, partition type 0x83
kernel /boot/vmlinuz-2.6.29.6-213.fc11.x86_64 ro root=UUID=63608748-e626-4a3f-9232-c836524f606f rhgb quiet
Error 2: Bad file or directory type
Darn grub thinks the file system type is ext2fs - this makes me think windows might have written something (perhaps its bootloader) to the first partition rather than the MBR.
View 10 Replies
View Related
Nov 10, 2009
I just upgraded by box from Fedora Core 9 to Centos 5.2. Finally!I have a 500GB SATA drive, it's partitioned into three equal size slices, hda1 through 3. The old Fedora was on hda1, I installed the new Centos on hda3. I instructed the installer to write the MBR to /dev/hda, not /dev/hda3. Fdisk says I have sector 0 unused.First, the system wouldn't boot - it just looped through the BIOS, rebooting over and over again. The BIOS sees the disk, but it never loaded Grub. I tried re-running grub-install /dev/hda, and not I get a Grub Error 17 after stage 1.5 loads.
I can boot from rescue OK, the grub.conf man menu.lst look fine, it's pointing to "root (hd0,2)". It's either the BIOS that can't find the MBR, or the MBR can't find Grub.When I looked at the disk with fdisk after the install, hda1 was still marked bootable, hda3 was not, so I swapped bootable flags but that has not made a difference. I also appended the new grub to the old grub thinking I could get the MBR (if it is there) to load the old grub and thence find the new Centos, but that didn't work either.Mobo is an old Shuttle AK35.Any ideas? Did I mess up by not telling the system to put the MBR on /dev/hda3? Is there a way to fix this without reinstalling?
View 2 Replies
View Related
Jun 4, 2011
So I have 2 ide hdds but whenever they are both connected, grub gets stuck at GRUB loading stage 1.5. how can I resolve this problem?
both are Maxtors with ext4 fs. primary is 20 gb and secondary 80 gb.
Jumpers are set to cable select.
Boot order in bios is correct. (primary first, secondary isn't in the list at all)
View 8 Replies
View Related
Nov 27, 2010
I decided to install Ubuntu on my desktop after the setup went well on my laptop and I liked the OS. I already had Windows 7 and Backtrack 9 installed on my HDD, so when I was in setup I took the 200gb partition for BT9 and formatted SDA5 to ext3 with "/" as the root. Then checked "format" and selected SDA5 from dropdown list and continued to install.Everything went smooth in the installation and I was prompted to reboot which I did assuming I would soon see a GRUB screen. Instead I got an error saying
"Grub loading stage1.5.
Grub loading, please wait...
error 15"
and then the computer just freezes. I've tried to boot from CD but I just get "CD-ROM Boot Priority ...Boot Ready" and then after about 30 seconds it tries to boot from the HDD and I get the same error.I've read that I need to configure GRUB somehow but I have no idea how to do that and I can't boot anything from a CD because it just waits and then jumps to the HDD. I guess what i'm asking is if there is a way to configure GRUB from the BIOS menu or make it possible to be able to boot from a CD.
View 9 Replies
View Related
Feb 24, 2009
I'm running Debian testing and after a recent software update, suddenly I can no longer boot into my single Linux kernel image anymore. I did look at the software update before I did it and I don't believe that it removed any software packages. When I try to boot into my linux 2.6.26-1-amd64 image, I get the following message from grub:"error: unknown command `initrd'"..The same error appears if I try to boot into single-user mode. I have a Windows XP partition on the same hard disk and I am still able to boot into that from grub. I've searched the net and haven't really found my same problem replicated anywhere. I would imagine that the problem is just that somehow the initrd package got removed in my last software update, but again I don't recall seeing any software that the update planned to remove.
Any thoughts on how I would go about fixing this problem? Since I'm unable to get into Linux at all, I imagine I'll have to use a LiveCD to get in and fix the problem, but I don't know where to begin looking.
View 8 Replies
View Related
Feb 26, 2010
I've been running openSuse 11.2 for a while on my notebook.Today I turned it off at work and came home. When I tried to turn it on, it boots, shows a black screen written 'GRUB' and then NOTHING. It doesn't complete the boot process.
View 9 Replies
View Related
Apr 17, 2010
I started another thread about this to get help booting into openSUSE after Fedora rewrote my bootloader and deleted all other entries. I managed to fix it but I never did find out why the following commands caused my system to boot to the grub shell instead of the grub menu.
Code:
grub
root (hd0,3)
setup (hd0)
quit
reboot
Can anyone explain to me why these commands caused my system to boot directly to a grub shell? It's as if there were no /boot/grub/menu.lst files for it to use, but after I got everything back to normal, the files were still there.
If it helps, this is how the drive was setup before and now, except Fedora was on /dev/sda4 and has since been deleted.
Code:
Device Boot Start End Blocks Id System
/dev/sda1 1 262 2104483+ 82 Linux swap / Solaris
/dev/sda2 263 13316 104856255 83 Linux
/dev/sda3 * 13317 14621 10482412+ 83 Linux
View 6 Replies
View Related
Feb 19, 2010
I made an xubuntu disk.loaded it and rewrote my hardrive.on a pretty old averatec laptop. 3/4 of the install it gives a a io error and stops the install.I tried to reinstall from the screen again but got the same error.So I rebooted and it skips everything and goes straight to a grub loading stage 1.5, grub loading error 17. It even skips the live cd.I also tried to do it thru a usb stick but that gets ignored too.
View 3 Replies
View Related
