I resized my windows c drive to make another drive which also has Open SUSE 11.4 dual booting which was working fine.
After reboot I get missing operating system so I boot the live Opensuse DVD and the windows and Linux is still there so I tried the boot configure tool in YAST but get the error because of partitioning the boot loader cannot be installed properly
Can I make a boot floppy somehow? I now have a grub menu when it boot sup but do not know what to do now
I did a fresh install of SuSE 11.4 (WIN7 TOO) and changed my Larger HD1 to the first HD. I was installing and got this error first: the boot loader is installed on a partition that does not lie entirely below 128GB The system might not boot if BIOS supports only lba24 (result is error during install grub mbr) status loc dev/sdb6
I continued with the install and then got:
Yast2 error occured while installing GRUB ver 0.97 (640k lower/3072k upper memory) [minimal bash-like lineediting is supported? for the first word, TAB lists possible command completition anywhere else TAB lists possible completion of a device/filename] grub setup --stage2=/boot/grub/stage2 --force4-lba (hd0,5) (hd0,5) Error 25 disk read error grub> quit
I just tried to install Ubuntu 10.04 on my windows machine. Unfortunately there was an installation error and now the computer will not boot up in windows anymore (I get grub error 17). I had Ubuntu 7.04 before, but when installing 10.04, I deleted the 7.04 partitions. Is there a way to recover the ability to boot into windows?
I'm dual booting Windows 7 and openSUSE. I attempted to start up my computer, and got ERROR 17 on the GRUB loading page. I am assuming this is related to me disabling the openSUSE uninstaller on startup in Windows.installer seemed completely superfluous.
I am currently rebuilding a couple laptops and a desktop to dual boot Windows and Suse 11.2. Windows is installed on partition 1. On the laptops, the build goes fine and dual boot with grub is OK. No issues. But on the desktop, the exact same build (after all the on-line updates, etc) fails with "Operating system not found" on the final (and first) boot. It seems that the Suse 11.2 build is somehow resetting the active partition and the boot does not see grub or Windows. When I reset partition #1 back to "active, only Windows loads. So I guess I need to fix this by reinstalling grub. Or use the Windows boot loader.
(1) Where is grub located on my system?
(2) What partiton is the Linux master Boot record If I wanted to use the Windows boot loader and do the following command to grab the 512 bytes I need:
dd if=/dev/sna? of=grub.bin bs=512 count=1
My partition layout is below. This is output from gdisk.exe in DOS7. It's an 80gig drive.
I am trying to Dual-boot Windows & and OpenSUSE 11.4, and have run into walls all over the place. Here is what I did:
1. Windows 7 was already installed. (Don't like it, freezes all the time) 2. Installed OpenSUSE using default partition options. 3. Booted into OpenSUSE with no problem 4. Tried booting into Windows, no joy. 5. Got that figured out, now I can get into Windows. 6. GRUB is gone, so now I can't get back into OpenSUSE.
I saw a good quick fix for grub after win 7 updates over here
My question is, after WIN 7 sp1 it seems every update win 7 does borks grub and resets the system to boot from the Win 7 boot partition, Is there a way to prevent this or is it going to be a boot from CD and repair after every update?
Cause I know M$ isn't going to want to fix it as they don't like sharing systems.
I dual booted opensuse along with vista. I installed opensuse in extended partition, with grub and gave the option as "boot from extended partition". Now everything is fine. I am able to boot into suse as well as vista. Now how can I restore my vista bootloader? I want to uninstall openSuse. When I try restore mbr from hard disk. There is absolutely no change!
I would like to recover my grub installation in a dual boot system. if there is an easy way to recover grub using flash disk? If yes is your suggestion opensuse developed? (currently running 11.3) . It would be nice also to have some gui just to make things easier. If not I assume that then the only option is the boot from dvd. Is that right?
I had dual boot PC (openSuse 11.3 / Windows XP). Then I had to reinstall Windows XP, so I lost dual boot capability. (No Grub boot options screen, directly Windows boot.)How can I reinstall Grub (only Grub)?I tried by booting with the openSuse installation DVD, but no repair option appears as in older versions.
A few days ago I went to perform the Service Pack 1 Upgrade for Win 7. This crashed out with an error. On researching the problem I found a solution to fix the problem by marking the Windows partition as active. I did this (via Computer Mgmt -> Disk Mgmt). This allowed the SP1 upgrade to work, however on reboot I got an error BOOTMGR missing. This I rather rashly resolved by using the Windows 7 install DVD in Recovery mode to reinstall the Windows Boot manager via bootrec /Fixboot I thought I would then be able to use the Opensuse 11.2 install disk to fix grub.
I use the Opensuse install disk and select Repair system -> Expert Mode -> Install New Boot Loader then select Other -> Reread Configuration from Disk. This adds Win 7 back into the grub menu. I then select OK and get the message "the bootloader was installed successfully". The problem then comes when I click my way through OK and Next to finish the install. At the end of the process I get the message "An error occurred during the installation" and I'm no further forward.
FYI the PC has a single SATA disk installed partitioned as follows:
dev/sda1 100Mb Win System Parkition dev/sda2 Windows NTFS dev/sda3 Windows FAT
Ubuntu 9.10 was set up to handle the booting selection - previously I thought it was xp but Ubuntu 9.10 "did" it. The system started out as a xp / ubuntu 9.10 dual boot on a 400gb drive. xp has 210gb, ub has 80 and their is a 100gb shared storage. Xp was installed first and then I followed a guide over at linuxconfig.org to get ub installed so that I could select which OS was wanted at boot. Ubuntu manages the boot up menu (Went back to look at my notes from the original setup) The owner tried to update to ub 11.04 and afterall was said and done the machine now boots to the message
error file not found grub rescue I can't say if 11.04 was properly installed or not. Ask whatever you like and I'll give the best answer I can. I think the xp install is okay but I can't say for certain as I don't know how to boot it outside the bootmanager at startup. Data has been saved so if I have to blow it all away and start over I can but I'm hoping I won't have to.
Recently I've installed Open Suse 11.3 along with Ubuntu 9.10 on my PC ( made it a dual-boot OS ). This morning while logged in, in Open Suse 11.3, found out that there were important update for kernel in Yast. So, did the update and then required to restart the PC. In the Grub/boot menu, I chose to log-in to Open Suse 11.3, but after a while it returned with " Error 15, file not found ". Luckily I was able to log-in in Ubuntu 9.10. Assumed that Error 15 is always related to misplaced or wrong configuration of Grub in the partition, I did several searching via Google, and found this possible solution HowTo Boot into openSUSE when it won't Boot from the Grub Code on the Hard Drive . So I tried the " Broken Grub menu: boot to the menu, drop to a console and boot openSUSE direct " method. But rightly after the " find /boot/grub/menu.lst " command as instructed in the solution, it returned with ( hd0,0 ) and ( hd0,4 ). Why there are 2 bootloader in the Grub ? Which bootloader should I choose ? And for convenience, here is my " menu.lst " folder that I get via Terminal in Ubuntu 9.10 :
A few days ago I decided to ditch Windows for good. I read for hours about a Linux distro and settled on OpenSUSE.
I just need to say one thing. Linux is not for the feint of heart, and everywhere I turn (forums), I see computers riddled with error messages, frustrated people, and the list goes on.
I'm willing to work through this though since I feel that the benefits will outweigh anything that Microsoft can offer, so here goes.
Upon installing the new build of OpenSUSE, I encountered an error message that was fixed by hitting retry (I forgot the name, but I remember it being something like Etk3 or something of the sort).
My issue now is not being able to boot into the OS. I'm getting Error 25 from GRUB on stage 1.5
I've installed 11.1 over my Windows XP partition. I want XP no more. Additionally, I read the sticky and followed all the instructions. I also selected the KDE desktop (I still don't know the difference between that and GNOME despite Googling it several times).
I have a single boot system that was working great until this morning when it locked up. I was working as I always do when the system stopped responding completely. CTRL+F1 did not work to allow me into the back so I could log in and see what was happening.
CTRL+SHIFT+SysRq did not recover the system or interrupt what ever was causing the lock up.
SSH from another system failed as the client did not respond
So I had to do a hard boot and when I did I got this:
GRUB Loading stage1.5.
GRUB loading, please wait... Error 17
Again this is a single boot system no Windows other than in VMWare inside the install. It is a multi drive with RAID set up workstation that I have at work. The short of it I am sole IT support as our companies ITS will not support Linux. In 5 years of operations with Linux at work this is my first issue, and I can't figure it out. I already tried the PartedMagic solution (ref = Re-Install Grub Quickly with Parted Magic) and that didn't work.
I re-installed the system completely even going to the extent to change my partition scheme just to make sure that wasn't the problem (which doesn't make sense as the system had been running for 46 days non-stop without a problem). Upon reboot after performing a complete security update I got the Error 17 message again.
Most of the filesystem tools and partition programs featured by Parted Magic include man pages. To read a manual page, simply type man and the name of the tool. (Examples: 'man ntfsprogs' or 'man fdisk')
Here the other day, I decided to try out 10.04 Alpha. But after I had done it, I weren't able to boot Vista anymore. When I choose it in the grub boot loader, it changes to only showing the word "GRUB", and nothing more happens. As a desperate attempt to fix it, and because I weren't happy using the Alpha, I then decided to switch back to 9.10, but the problem with booting Vista persists.
I was trying to install Backtrack - Ubuntu dual boot with ubuntu pre-installed. I created another partition for backtrack but now grub doesn't point to the correct file in order to start Ubuntu, and so only backtrack starts. How can I correct it? I am able to mount my Ubuntu Partition and the files at /boot/ (in the ubuntu partition) mentioned at menu.lst at /boot/grub/ on the backtrack partition seem to exist... Does anybody know what should I do? (e.g. point menu.lst to the /dev/sda1/boot/IMAGES or something?)
I am new to Fedora, having used Ubuntu for 2 years. However, I am a little dissappointed in the latest Ubuntu releases and want to try something new. So I installed Fedora 10 on my second hard drive, deleting Ubuntu. On my first hard drive, I have Vista installed. During installation I followed a guide for dual-booting and it said not to install Grub to the MBR of the Windows partition, so I followed that advice...
This caused a Grub error 15 on the next boot. I booted the Fedora installation from the second hard drive. My hypothesis is that the Grub bootloader of Ubuntu was still installed somewhere and it could not find the Ubuntu linux kernel. Therefore, it gave error 15. So I installed Vista again and am hesitant to try Fedora again... How can I install Fedora alongside Vista properly (as dual boot)?
Or should I stay away, because it is apparently too difficult for me? Is it worthwhile to make a separate /home partition as I read that it is preferred to do a clean install every release? Could I just do that with Gparted and then assign the partition as /home in the Anaconda installer? The downside is that I then need to create a swap and / partition too, right?
This will make the third time I have tried to load Ubuntu and it has wiped out my Win OS twice and am not sure it hasn't done it again. I installed a 40gb hdd as a slave, have XP on the master. In the process of installing I picked the drive that corresponded to the slave. Didn't understand the the names or titles Ubuntu used but proceeded and the installation went fine although I never saw a place to load Grub on the master drive. After rebooting a couple of times saw the option to click Esc for boot menu but the only choices given were Ubuntu, ubuntu recovery and ubuntu kernel. Can find no mention of my W OS. Have tried to unplug the slave drive but can't boot then as get error message of Grub error.
HW config is: AMD Athlon 64 X2 5000+ Black Edition, MSI 785GTM-E45, 2X 1Gb Kingston HyperX PC2-8500. I have set up GRUB to dualboot openSUSE 11.2 and WindowsXP. Initially i had set up system with defaults: CPU@2600MHz (200X13) and therefore RAM@800MHz. Both openSUSE 11.2 and WindowsXP worked just fine. Memtest86 found no problems.
But after a while i decided to change this setup to: CPU@2500MHz (250X10) and therefore RAM@1000MHz, as it promised better overall performance. And now Windows still boots and works better then before. Memtest86 still can't find any problem. But openSUSE 11.2 hangs at boot. I've suspected cpufreq governor, but changing from Ondemand to Conservative in /sys/devices/system/cpu/cpu0/cpufreq doesn't help.
I cannot count how many times I have re-installed squeeze, and do all kinds of fixes to grub, but no joy. Every time, there is this ntoskrnl.exe error, and to re-install it. I thought my WIN XP may be corrupted, so I reinstalled it, and updated it with sp3 and all updates. Then I re-installed squeeze (reformatting all partitions). At the end, the installer ask if I want to install grub to mbr. I replied yes. After reboot, only the 2.6.32.3-amd64 and the recovery kernels show up on the grub screen, no winxp.OK, I booted into squeeze kernel and looked at the /boot/grub/grub.cfg file, and there winxp is not included in /etc/grub.d/30_os-prober section. In terminal, I typed
#os-propber and it found winxp in /dev/sda1 then I typed #update-grub
and now /etc/grub.d/30_os-prober now show winxp.I rebooted, and winxp shows on the grub screen, and I chose winxp.It came back with "ntoskrnl.exe ...error... re-install ntoskrnl..."Here are the details:
I just installed Fedora15 on my laptop. When the installation completed, the system rebooted and gave me a Grub Error 17. I logged in the rescue mode and got the following output from
Code: fdisk -ls
Code: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0d8b0d8a .....
My system has Windows XP Pro SP2 installed on /sda1 and originally a 10.04 on /sdb1-3, now upgraded to 11.04. The Ubuntu system works fine (teething troubles with nvidia drivers on upgrade but fixed now), and the Windows system shows up in the grub menu, but when it's selected, I just get `GRUB Hard Disk Error' and nothing else. Windows installed properly, and booted successfully until I installed Ubuntu in the first place. I can still access the files on that drive from within Ubuntu.
I've tried fixboot in the Win Recovery Console, which sounded like it did something, but didn't fix the problem. This problem isn't new to grub2, by the way - I just haven't needed Windows in a year.
I have a dual boot System with Ubuntu 10.04 Netbook Remix and Windows XP SP3 on an Asus eeePC 1000HE. I had some troubles with updating kernels etc. and I ended up with following problem:
After grub reinstall, I am able to boot Ubuntu, also I can mount the windows partition properly. Trying to boot into Windows, I get the error:
Code:
It's all on one hard drive which doesn't show any errors:
Code:
Partition table entries are not in disk order
Code:
Some partitions don't show a file system because they are luks-encrypted.
As I mentioned earlier, I am able to mount sda1. I think the problem is that the Partition Boot Sector is corrupted, even though I am not sure if the ntfs partition is damaged at all or if GRUB is the problem.
As I said I had problems with a kernel update and therefore had to reinstall GRUB. I think, but I am not sure, that I accidentally installed GRUB on sda1 (the windows partition) instead of on sda. After I installed GRUB on sda again, I was able to boot linux and fixed sda1 with testdisk. Before, sda1 showed as four partitions (sda1p1, ... , sda1p4). I was not able to mount sda1 till I fixed it with testdisk. testdisk says the Boot Sector of sda1 is OK, so does ntfsfix.
Finally, an extract from my /boot/grub/menu.lst:
Code: ...
The Windows XP entry is added by myself. I don't know much about grub, so there might be the error.
I tried to keep it as short as possible (this is only the end of the story), I hope I didn't forget anything important. Please ask if there is something not clear.
I am in Tanzania with this netbook, so it is not possible to boot Windows CD and fix the windows partition with it, also I don't have a very fast Internet connection.
Is there a way to fix this without a Windows CD? Maybe it is just a dumb mistake in the menu.lst?
I had Ubuntu installed, i installed Debian and there was no dual boot. So i formated all the hard disk to install only Debian. It installed but at boot i get error: no such device and the grub rescue> prompt. i googled for a solution and nothing worked:
- i tryed reinstalling grub, not worked - i did the windows cd fixmbr trick, not worked - reinstalled debian with fixmbr the first step and nothing - tryed deleting with dd the mbr, not worked - reinstalled grub from debian rescue, not worked
what should i do? i can't access my computer? please tell me how should i fix it? the google guys will kill me because i put their servers on fire
After upgrading to 10.04 from 9.10 Win7 wouldn't startup any more. So I tried this HowTo: [URL] to restore Grub2. But now each time I boot up I get this two lines: error file not found grub rescue> I have NO idea what to do.
Im currently not an linux expert so I turn to this forum after several attempts to fix my issue with grub.
I had a dualboot single HD with both win7 and win8.1 when I decided to install debian wheezy from usb.
I deleted the win7 partition and installed debian there. The partition scheme is separate /home
After reboot I automatically get into the "Grub rescue mode" and now I´m stuck.
I tried the commands:
set prefix=(hd0,msdosX)/boot/grub/ Insmod normal
I have msdos1, msdos3, msdos5 and msdos6 but nothing is listing anything from the grub rescue mode.
I get the "UNKNOWN FILE SYSTEM" error and cant get past that.
I also tried booting into rescue mode from usb iso install but nothing happens when choosing to repair GRUB.
The listed devices in rescue mode are:
/dev/sda1 /dev/sda2 /dev/sda3 /dev/sda5 /dev/sda6 debian uses sdb 1-2 and sdb1 is the only option to Reinstall GRUB on but it gives me "Unable to install GRUB in /dev/sdb1 This is a fatal error" message /dev/sdb1 /dev/sdb2
I'm having serious troubles to install ubuntu-10.04.1. My raid is an hardware raid with intel chipset. Note that win7 is already installed and working with my raid. I made some space from windows, to install Ubuntu (40gb). First, I run the installer, everything seems to be fine. I choose to install Ubuntu were there is the most space free (sorry, I'm not sure about the real terms used there).
Then my partition with the vista loader appears. So the installer can see my raid, and should work fine (everything is detected correctly). But once I'm in the end of the installation (around 95%), a pop-up appears, and tells me that Grub can't install in /dev/sda and it's a fatal error. I can choose an another destination, but it doesn't seems to work.
I installed Windows 7 and then Ubuntu 10.10 64 bits. The Ubuntu installation went fine but when rebooting a "check disk" appeared and since then my PC keeps booting directly on Windows. I tried all the GRUB reinstallation methods of the GRUB2 Community Documentation with the live CD but none worked.
Below is the output of the Boot Info script found on several threads.
I installed Opensuse 11.3 on a separate partition to vista on my Acer 5115. It runs fine but the GRUB boot loader failed to show the Vista OS. I tried to add it by editing menu.As far as I can see (and I don't have much experience with these things) the Vista OS is there, on sda5, but doesn't boot correctly because the winload.exe is in the wrong directory. Why the sdax numbers are all rearranged is a mystery too, but I have reinstalled vista several times so that could be why.I don't have a vista recovery cd (wasn't given one), is there any way to fix this within opensuse (which works fine)?
