OpenSUSE Install :: Unable To Re-load Grub Following Windows 7 SP1 Upgrade On Dual-Boot?
Apr 28, 2011
A few days ago I went to perform the Service Pack 1 Upgrade for Win 7. This crashed out with an error. On researching the problem I found a solution to fix the problem by marking the Windows partition as active. I did this (via Computer Mgmt -> Disk Mgmt). This allowed the SP1 upgrade to work, however on reboot I got an error BOOTMGR missing. This I rather rashly resolved by using the Windows 7 install DVD in Recovery mode to reinstall the Windows Boot manager via bootrec /Fixboot I thought I would then be able to use the Opensuse 11.2 install disk to fix grub.
I use the Opensuse install disk and select Repair system -> Expert Mode -> Install New Boot Loader then select Other -> Reread Configuration from Disk. This adds Win 7 back into the grub menu. I then select OK and get the message "the bootloader was installed successfully". The problem then comes when I click my way through OK and Next to finish the install. At the end of the process I get the message "An error occurred during the installation" and I'm no further forward.
FYI the PC has a single SATA disk installed partitioned as follows:
dev/sda1 100Mb Win System Parkition
dev/sda2 Windows NTFS
dev/sda3 Windows FAT
View 8 Replies
ADVERTISEMENT
Jul 19, 2010
I installed ubuntu 10.04, aftert that i cluld not able to start windows xp,Please find the details about my hard disk
Disk /dev/sda: 40.0 GB, 40020664320 bytes
255 heads, 63 sectors/track, 4865 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
[code]....
View 2 Replies
View Related
Apr 24, 2010
I am unable to load Ubuntu onto computer as dual boot or inside windows. Thus scanned the CD and found it has 23 errors.Are these files suppose to be on the CD?casper, .disk, install, install, isolinux, pics, pool, pressed, autorun, md5sum.
View 4 Replies
View Related
Mar 23, 2011
I had a dual boot system with 3 partitions, Windows 7 on one partition, and Windows XP on another partition and a Data partition. I decided to load Ubuntu 10.10 on the Windows XP partition.During installation I selection manual partition, and deleted Windows XP.after successful completion of Ubuntu installation "Grub" directly boots into Ubuntu, it doesn't show me the OS selection screen. After following some forum posts I did an update grub
Code:
Generating grub.cfg ...
Found linux image: /boot/vmlinuz-2.6.35-22-generic
Found initrd image: /boot/initrd.img-2.6.35-22-generic
[code]....
View 8 Replies
View Related
Apr 20, 2010
HW config is: AMD Athlon 64 X2 5000+ Black Edition, MSI 785GTM-E45, 2X 1Gb Kingston HyperX PC2-8500. I have set up GRUB to dualboot openSUSE 11.2 and WindowsXP. Initially i had set up system with defaults: CPU@2600MHz (200X13) and therefore RAM@800MHz. Both openSUSE 11.2 and WindowsXP worked just fine. Memtest86 found no problems.
But after a while i decided to change this setup to: CPU@2500MHz (250X10) and therefore RAM@1000MHz, as it promised better overall performance. And now Windows still boots and works better then before. Memtest86 still can't find any problem. But openSUSE 11.2 hangs at boot. I've suspected cpufreq governor, but changing from Ondemand to Conservative in /sys/devices/system/cpu/cpu0/cpufreq doesn't help.
View 9 Replies
View Related
May 17, 2010
I recently performed a reinstall of ubuntu after mucking up my partitions, and I am running it dual booted with windows 7.
I recently performed a grub-pc update, but I didn't know what it was asking me to do during the process itself of updating the process.
It asked me at one point where to install grub, and I selected all my partitions because it suggested that if I didn't know. I think that may have damaged my windows section, which was also selection.
I've attached the output for:
Code:
Problem symptoms:
1) Weird upgrade error in apt-get
2) Unable to boot windows 7
3) Unable to activate proprietary drivers
4) Perpetually being reminded to restart
View 5 Replies
View Related
Jul 24, 2010
yestoday,after I upgrade,unable to boot windows xp. if I use grub ,windows xp can boot up.but now I want to use grub2, boot info script's results.txt is at below.
Boot Info Script 0.55 dated February 15th, 2010
Boot Info Summary: => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in
partition #6 for /boot/grub.
sda1:
File system: vfat
Boot sector type: Fat16
Boot sector info: No errors found in the Boot Parameter Block.
[Code]....
View 1 Replies
View Related
Mar 20, 2011
I'm trying to install OpenSUSE 11.4 (64bit with the server options included) on my Mac (Core 2 Duo 2.0 Ghz with 2 GB memory). So I have sda2 the OSX, sda1 swap, sda3 is the bootcamp (windows), sda4 (ext4) and sda5(ext5). I installed rEFIt 0.14 first, then I reboot with DVD on. The installation setup resized the Windows partition from Bootcamp, and create 3 other partitions (the sda1,4 and 5). At the installation I choos MBR enable and "/" as home enable.
At the end of the installation I have the error about MBR, that can't mount, or create the mount point? I'll double check the exact message. Anyway, when I try to load OpenSUSE, is not working: can not load the system. I tried to find on the installation menu a repair (I thought that I can find an utility to fix the MBR). I don't want to choose other distribution, because I used SuSE before, and I really like it, and of course this way I can learn more about troubleshooting a Linux installation on different environment
View 9 Replies
View Related
Feb 10, 2011
On reboot the GRUB2 installer shows me the options for OS - I select Windows XP and then I get a blank screen with a flashing cursor - and nothing.. I CTRL ALT DEL and it reboots back to GRUB2 and I select UBUNTU and I log in. This is the first time I have tried to reboot Windows XP after fresh install of UBUNTU
[Code]....
View 9 Replies
View Related
Apr 30, 2011
I resized my windows c drive to make another drive which also has Open SUSE 11.4 dual booting which was working fine.
After reboot I get missing operating system so I boot the live Opensuse DVD and the windows and Linux is still there so I tried the boot configure tool in YAST but get the error because of partitioning the boot loader cannot be installed properly
Can I make a boot floppy somehow? I now have a grub menu when it boot sup but do not know what to do now
View 9 Replies
View Related
May 31, 2010
Two days ago i turned on my pc and suddenly there was a message:"Minimal Bash-like line editing is supported.For the first word,TAB lists possible command completions.Anywhere else TAB lists the possible completions of a device/filename.ESC any time exists...
When i googled this message it came out that this has got to do with linux (i have never used linux and i formated my disc once or twice since i bought it so i found it very strange that this problem is related to linux).Anyway,i found out that grub is the problem and that it isnt a big deal to solve it.I downloaded Ubuntu,booted it from the cd and followed the instructions...I typed in grub (in the terminal) and it told me to download it so i typed in "get-apt grub install" or something like that and it all went well,i was now in the grub directory.Then i typed " find /boot/grub/stage1" and it told me that the file was not found.
I have tried everything,i have downloaded the super rescue cd the fix the problem but i have still the same problem.
View 2 Replies
View Related
Apr 12, 2011
Finally made the switch over to ubuntu, but I needed to keep my windows7 for several reasons. Let just start by saying I have two hard drives, a 200gig(which holds my windows7 partition) and a 500gig(has a 100gig partition which has ubuntu on it). After finally getting 10.04 to install on the 100gig partition and everything running right, I tried to load up windows7 and got an error.
Something along to lines of "the partition does not exist". I believe I messed up on the last step on the install, as I might of just been careless. I remember reading somewhere that if using multiple hard drives grub may get messed up in one way or another. IS there a way to fix this and make grub realize that window7 is on another partition, or am I out of luck?edit: Id like to add that grub is recognizing windows7, it just will not load off the other partition(I think)
View 4 Replies
View Related
Apr 27, 2011
I did a fresh install of SuSE 11.4 (WIN7 TOO) and changed my Larger HD1 to the first HD. I was installing and got this error first: the boot loader is installed on a partition that does not lie entirely below 128GB The system might not boot if BIOS supports only lba24 (result is error during install grub mbr) status loc dev/sdb6
I continued with the install and then got:
Yast2 error occured
while installing GRUB ver 0.97 (640k lower/3072k upper memory)
[minimal bash-like lineediting is supported? for the first word, TAB lists possible command completition anywhere else TAB lists possible completion of a device/filename]
grub setup --stage2=/boot/grub/stage2 --force4-lba (hd0,5) (hd0,5)
Error 25
disk read error
grub> quit
View 9 Replies
View Related
Jan 24, 2010
I am currently rebuilding a couple laptops and a desktop to dual boot Windows and Suse 11.2. Windows is installed on partition 1. On the laptops, the build goes fine and dual boot with grub is OK. No issues. But on the desktop, the exact same build (after all the on-line updates, etc) fails with "Operating system not found" on the final (and first) boot. It seems that the Suse 11.2 build is somehow resetting the active partition and the boot does not see grub or Windows. When I reset partition #1 back to "active, only Windows loads. So I guess I need to fix this by reinstalling grub. Or use the Windows boot loader.
(1) Where is grub located on my system?
(2) What partiton is the Linux master Boot record If I wanted to use the Windows boot loader and do the following command to grab the 512 bytes I need:
dd if=/dev/sna? of=grub.bin bs=512 count=1
My partition layout is below. This is output from gdisk.exe in DOS7. It's an 80gig drive.
1 = Windows-7
2 = /boot
3 = swap
[code]....
View 9 Replies
View Related
Apr 1, 2011
I am trying to Dual-boot Windows & and OpenSUSE 11.4, and have run into walls all over the place. Here is what I did:
1. Windows 7 was already installed. (Don't like it, freezes all the time)
2. Installed OpenSUSE using default partition options.
3. Booted into OpenSUSE with no problem
4. Tried booting into Windows, no joy.
5. Got that figured out, now I can get into Windows.
6. GRUB is gone, so now I can't get back into OpenSUSE.
View 8 Replies
View Related
Jun 17, 2011
I saw a good quick fix for grub after win 7 updates over here
My question is, after WIN 7 sp1 it seems every update win 7 does borks grub and resets the system to boot from the Win 7 boot partition, Is there a way to prevent this or is it going to be a boot from CD and repair after every update?
Cause I know M$ isn't going to want to fix it as they don't like sharing systems.
I'm running
OpenSuse 11.4 Win 7 sp1 dual boot
View 3 Replies
View Related
Dec 12, 2009
I dual booted opensuse along with vista. I installed opensuse in extended partition, with grub and gave the option as "boot from extended partition". Now everything is fine. I am able to boot into suse as well as vista. Now how can I restore my vista bootloader? I want to uninstall openSuse. When I try restore mbr from hard disk. There is absolutely no change!
View 1 Replies
View Related
Nov 19, 2010
I would like to recover my grub installation in a dual boot system. if there is an easy way to recover grub using flash disk? If yes is your suggestion opensuse developed? (currently running 11.3) . It would be nice also to have some gui just to make things easier. If not I assume that then the only option is the boot from dvd. Is that right?
View 9 Replies
View Related
Jan 8, 2011
I had dual boot PC (openSuse 11.3 / Windows XP). Then I had to reinstall Windows XP, so I lost dual boot capability. (No Grub boot options screen, directly Windows boot.)How can I reinstall Grub (only Grub)?I tried by booting with the openSuse installation DVD, but no repair option appears as in older versions.
View 5 Replies
View Related
Sep 13, 2010
i have a toshiba laptop running Windows 7 64 bit and i would like to install openSUSE 11.3 64 bit on it. I downloaded the DVD version and would like to know how i should do it.
View 1 Replies
View Related
Dec 10, 2010
My main os, albeit only because of gaming, is windows 7, and I was looking to dual boot with 11.3. I couldn't find any documentation of this, so here it goes: Does the executable on the 11.3 disk install opensuse like wubi does ubuntu?
View 9 Replies
View Related
Apr 6, 2011
I am trying to dual boot windows 7 and openSuse. I have shrunk my main partition and it is now unallocated. When running the DVD at the disc section I got the message Delete partition /dev/sda1 (199.00MB) This is my windows system partition (NTFS)
Delete windows partion /dev/sda2 (261.49GB) This is my main partition C: (NTFS) (Don't want to delete this Resize impossible due to inconsistent fs. Try checking fs under windows. Delete windows partition /dev/sda3 (16.31GB)This is my recovery partition.(NTFS) I also don't want to delete this. Resize impossible due to inconsistent fs. Try checking fs under windows. Delete partition /dev/sda4 (103.34MB) HP tools (FAT32) (Not sure about this, but would rather keep it.
Create swap volume /dev/sda1 (2.01GB)
Create root volume /dev/sda2 (20GB with ext4)
create volume /dev/sda3 (276.08GB for /home)
I also pressed created partition and clicked on the unallocated space but I got an error telling me that I either didn't have enough space or hadn't selected enough partitions. (The unallocated space was 20GB)
View 9 Replies
View Related
May 2, 2010
I am dual booting windows 7 and Ubuntu, and since the upgrade from 9.10 to 10.04 Windows 7 won't load.I tried the solution posted in another thread with a similar problem but to no avail.[URL]
View 9 Replies
View Related
Aug 18, 2010
Dual Booting my laptop and unable to change the Boot Records on the drive. Not because I dont know how, but my primary OS will fail to boot(win7).
I have drive partitioned as follows...
sda1 = Win7 system (default install)
sda2 = Win7 Main (default install)
sda3 = swap
sda4 = Extension (I think thats what its called)
sda5 = / (ext4)
What I need is a boot cd or perferably Grub installed on a 256MB Thumb drive with the options to load the installed system from sda5.
View 4 Replies
View Related
Nov 27, 2009
I just did an upgrade from 11.1 to 11.2 and can not boot to OpenSUSE any more. That happened when the first reboot was starting after finishing the upgrade from the DVD. I tried to find the issue and use the repair system with no luck yet. Now I get no gfx for grub
The only thing I managed is to add the windows boot section for windows but I can not seem to boot to opensuse. device.map:
Code:
(hd1)/dev/disk/by-id/ata-ST3160815AS_5RA2LTD0
(hd2)/dev/disk/by-id/ata-ST3160815AS_5RA2LQCJ
(hd0)/dev/disk/by-id/ata-Maxtor_6L160P0_L31AHTVG
device.map.old
[Code]...
View 9 Replies
View Related
Dec 3, 2009
I Need instructions on how to create a dual boot with Windows 7 already installed ...
View 2 Replies
View Related
Sep 29, 2010
Yesterday (Sept. 28) I managed to install openSuSE 11.3 on my Toshiba Satellite Pro C650 laptop, side-by-side with Windows 7 which was pre-installed. In brief I'd like to report the problems I had encountered up to yesterday.
1. Upon inserting the DVD and after the start of the installation the system would take me to non-GUI (Text) Mode and would finally respond with the message: "No repository found."
2. After that I tried to install openSuSE 11.2 and 11.1. There, although the installation went through smoothly, I had to deal with a new problem; when I selected to boot Windows 7 from the grub menu the system responded with the message:
rootnoverify (hd0,1)
chainload +1
BOOTMGR is missing
Upon booting the computer from the DVD with the Linux OS and before I hit ENTER I changed the Kernel by hitting F5 (or whatever key corresponds to Kernel at the bottom of screen) to "Failsafe mode". That did the job. The installation started and ended smoothly. Oh! one other thing I did is to edit the preselected disk partition and delete the swap partition since the disk has to have four and not five partitions.After that, I became root and edited "/boot/grub/menu.lst" file to correct the "(hd0,1)" for the Windows 1 to "(hd0,0)" since it is the first OS.
View 1 Replies
View Related
Nov 5, 2010
I am very much excited to try out openSUSE 11.3.. But i am very much afraid of losing my data in windows partitions without knowing the exact procedure to install it..here are my existing partition list... Please have a look at it and suggest me..
c : 40 GB
d: 120 GB
e: 140 GB
f: 140 GB
and i have some free space of 28 GB.It is unallocated.I want to install openSUSE into this free space.Now please tell me whether i can proceed with the default disk configurations given at the install time or do i have to modify and adjust the partitions or do i have to create partitions for the available free space.
View 9 Replies
View Related
Nov 11, 2010
I'm doing some research for a friend who wants to dual boot Windows 7 with a Linux Distro that has Perl inbuilt & also supports .MP3 and other popular codecs "out of the box"
From my limited research, OpenSUSE seems to fit the bill (as does Mandriva Powerpack).
Also, how easy is it to create a dual-boot with Windows 7 with this distro?
View 5 Replies
View Related
Mar 27, 2011
i have openSUSE 11.3 as my primary OS. and i want to be able to dual boot windows vista. from what i read i would have to reinstall the 11.3 to set up to dual boot. i may have that wrong.
View 2 Replies
View Related
