OpenSUSE Install :: GRUB Error 17 On Single Boot System 11.4

Jun 29, 2011

I have a single boot system that was working great until this morning when it locked up. I was working as I always do when the system stopped responding completely. CTRL+F1 did not work to allow me into the back so I could log in and see what was happening.

CTRL+SHIFT+SysRq did not recover the system or interrupt what ever was causing the lock up.

SSH from another system failed as the client did not respond

So I had to do a hard boot and when I did I got this:

GRUB Loading stage1.5.

GRUB loading, please wait...
Error 17

Again this is a single boot system no Windows other than in VMWare inside the install. It is a multi drive with RAID set up workstation that I have at work. The short of it I am sole IT support as our companies ITS will not support Linux. In 5 years of operations with Linux at work this is my first issue, and I can't figure it out. I already tried the PartedMagic solution (ref = Re-Install Grub Quickly with Parted Magic) and that didn't work.

I re-installed the system completely even going to the extent to change my partition scheme just to make sure that wasn't the problem (which doesn't make sense as the system had been running for 46 days non-stop without a problem). Upon reboot after performing a complete security update I got the Error 17 message again.

Below is the output of fdisk -l

Code:
Welcome - Parted Magic (Linux 2.6.30.6-pmagic)

Most of the filesystem tools and partition programs featured by Parted Magic include man pages. To read a manual page, simply type man and the name of the tool. (Examples: 'man ntfsprogs' or 'man fdisk')

[Code].....

View 9 Replies


ADVERTISEMENT

OpenSUSE Install :: Clean Install 11.4 Dual Boot System Grub Error?

Apr 27, 2011

I did a fresh install of SuSE 11.4 (WIN7 TOO) and changed my Larger HD1 to the first HD. I was installing and got this error first: the boot loader is installed on a partition that does not lie entirely below 128GB The system might not boot if BIOS supports only lba24 (result is error during install grub mbr) status loc dev/sdb6

I continued with the install and then got:

Yast2 error occured
while installing GRUB ver 0.97 (640k lower/3072k upper memory)
[minimal bash-like lineediting is supported? for the first word, TAB lists possible command completition anywhere else TAB lists possible completion of a device/filename]
grub setup --stage2=/boot/grub/stage2 --force4-lba (hd0,5) (hd0,5)
Error 25
disk read error
grub> quit

View 9 Replies View Related

OpenSUSE Install :: Commands Make System Boot To Grub Shell Instead Of Grub Menu?

Apr 17, 2010

I started another thread about this to get help booting into openSUSE after Fedora rewrote my bootloader and deleted all other entries. I managed to fix it but I never did find out why the following commands caused my system to boot to the grub shell instead of the grub menu.

Code:
grub
root (hd0,3)
setup (hd0)
quit
reboot

Can anyone explain to me why these commands caused my system to boot directly to a grub shell? It's as if there were no /boot/grub/menu.lst files for it to use, but after I got everything back to normal, the files were still there.

If it helps, this is how the drive was setup before and now, except Fedora was on /dev/sda4 and has since been deleted.

Code:
Device Boot Start End Blocks Id System
/dev/sda1 1 262 2104483+ 82 Linux swap / Solaris
/dev/sda2 263 13316 104856255 83 Linux
/dev/sda3 * 13317 14621 10482412+ 83 Linux

View 6 Replies View Related

OpenSUSE Install :: Restart System Some Times It Shows Grub Error As 17 Or 15

Jul 25, 2011

when i restart my system some times it shows grub error as 17 or 15 and in that situation used the dvd rescue mode and run the commands

e2fcsk -f /dev/sd1
e2fsck -b 9130 /dev/sda1

but no use any one that how to trouble shoot these grub errors tell me commands need to be run there.

View 1 Replies View Related

OpenSUSE Install :: Where Is Grub Loaded On Dual-boot System

Jan 24, 2010

I am currently rebuilding a couple laptops and a desktop to dual boot Windows and Suse 11.2. Windows is installed on partition 1. On the laptops, the build goes fine and dual boot with grub is OK. No issues. But on the desktop, the exact same build (after all the on-line updates, etc) fails with "Operating system not found" on the final (and first) boot. It seems that the Suse 11.2 build is somehow resetting the active partition and the boot does not see grub or Windows. When I reset partition #1 back to "active, only Windows loads. So I guess I need to fix this by reinstalling grub. Or use the Windows boot loader.

(1) Where is grub located on my system?

(2) What partiton is the Linux master Boot record If I wanted to use the Windows boot loader and do the following command to grab the 512 bytes I need:

dd if=/dev/sna? of=grub.bin bs=512 count=1

My partition layout is below. This is output from gdisk.exe in DOS7. It's an 80gig drive.

1 = Windows-7
2 = /boot
3 = swap

[code]....

View 9 Replies View Related

OpenSUSE Install :: Grub Dual Boot Error

Apr 30, 2011

I resized my windows c drive to make another drive which also has Open SUSE 11.4 dual booting which was working fine.

After reboot I get missing operating system so I boot the live Opensuse DVD and the windows and Linux is still there so I tried the boot configure tool in YAST but get the error because of partitioning the boot loader cannot be installed properly

Can I make a boot floppy somehow? I now have a grub menu when it boot sup but do not know what to do now

View 9 Replies View Related

OpenSUSE Install :: Recover Grub Installation In A Dual Boot System?

Nov 19, 2010

I would like to recover my grub installation in a dual boot system. if there is an easy way to recover grub using flash disk? If yes is your suggestion opensuse developed? (currently running 11.3) . It would be nice also to have some gui just to make things easier. If not I assume that then the only option is the boot from dvd. Is that right?

View 9 Replies View Related

OpenSUSE Install :: Unable To Boot Into The OS - Error 25 GRUB Stage 1.5 ?

Jul 31, 2009

A few days ago I decided to ditch Windows for good. I read for hours about a Linux distro and settled on OpenSUSE.

I just need to say one thing. Linux is not for the feint of heart, and everywhere I turn (forums), I see computers riddled with error messages, frustrated people, and the list goes on.

I'm willing to work through this though since I feel that the benefits will outweigh anything that Microsoft can offer, so here goes.

Upon installing the new build of OpenSUSE, I encountered an error message that was fixed by hitting retry (I forgot the name, but I remember it being something like Etk3 or something of the sort).

My issue now is not being able to boot into the OS. I'm getting Error 25 from GRUB on stage 1.5

I've installed 11.1 over my Windows XP partition. I want XP no more. Additionally, I read the sticky and followed all the instructions. I also selected the KDE desktop (I still don't know the difference between that and GNOME despite Googling it several times).

View 9 Replies View Related

OpenSUSE Install :: Grub Error 18 - Unknown File System - Running From External Hard Drive

Jan 11, 2011

It started when I wanted to dual boot Windows 7 and Opensuse off of my netbook (No DVD/CD drive) I tried install suse from an external hard drive and I botched it. I ended up erasing EVERYTHING off of my internal netbook hard drive. Windows and all.

Well, I had a couple of other computers so I studied up and eventually successfully installed OpenSUSE 11.2 on my external hard drive (11.3 being the one that I accidentally erased everything with, so kinda scared of it) and now I want to install openSUSE 11.2 on my internal netbook hard drive.

I can not use disks

I can not use a flash drive (For some reason, even if I make it bootable, it will not load up, this could be because it's actually a 8GB microSD card that is placed in a USB card reader.)

I can not use an external hard drive because that's what I'm running suse off of.

I've tried reading up on how to install suse on another drive off of the hard drive and I've gotten as far as whenever I boot up the netbook with the suse external hard drive connected it will ask to boot into OpenSUSE, the Fail Safe, or to install OpenSuse. When I select to install it it gives me the Error 18 Unknown File system.

I've tried formatting the internal hard drive twice. One as NTFS and again as EXT4. Neither seems to effect it other than when it's ext4 I can open it and it contains a Lost and Found folder.

When I interrupt the boot sequence by pressing c and going to the terminal and I use the root (hd +TAB command it tells me I have a hd0 and a hd1. The hd1 only has 1 partition which is ext4, which I'm assuming hd1 is the internal hard drive (I'm not sure how to check) and the hd0 is the external hard drive, which has three partitions. One with an unknown file system and two with ext4. When I try to enter the set up from the terminal it gives me the same error for any thing I put it (e.g. root (hd0,0) gives the same error as root (hd0,1), or root (hd0,2) and root (hd1,0)

Something like it cannot locate these two files I'm assuming it needs to boot. If anyone finds this relevant I'll retry it and post the files its missing.

I've been searching for awhile and can't find any threads that can solve my problem. From other threads, however, I have noticed that I should probably include my menu.lst, listed below

Code:

I have also ran the boot info script and received the RESULTS.txt file it generates. Listed below

Code:

View 9 Replies View Related

OpenSUSE Install :: System Freezes After GRUB (Normal Or Failsafe) Boot Splash Screen

Apr 17, 2011

I noticed that after making my build in suse studio my system freezes immediately after GRUB ( Normal or Failsafe) boot splash screen. I also noticed that this happens only with the specified kernel below. I'm not sure when using Kernel 2.6.37, one had the same problem. I never used it. The original kernel 2.6.34 had no problems such as the one I have described. My systems has no further problems only that it takes several restarts to go past the "Freeze". Below is a list of my system specs:

openSUSE 11.3
Kernel-pae 2.6.38.2-4.1 from Kernel Stable.
GRUB 0.97-174.1 from openSUSE 11.4
Upstart 0.6.5-33.1
xorg-x11-server 7.6_1.9.3-142.1 from X11:xorg 11.3 repo.

The GRUB from openSUSE 11.4 has been very stable and non-problematic. I will be buying an Intel core i5-2500K in a few months that's why I need the latest kernel and XOrg-X11-server. What could be causing the freezing?

View 6 Replies View Related

OpenSUSE Install :: Error After Boot \ When Start The System, Opensuse Is Not Open With This Lines?

Jul 4, 2011

I set up opensuse 11.4. I updated nvidia 6600 drivers from vendor. Everything is good until automatic kernel update. When I start the system, opensuse is not open with this lines.

/etc/rc.status: line 1: /bin/ash : no such file or directory
bash: ./etc/sysconfig/chron : cannot execute binary file
X_MOUSE_CURSOR : Undefined variable

[code]....

View 3 Replies View Related

OpenSUSE Install :: 11.3 - Red Error: "the Boot Loader Installed On A Partition That Does Not Lie Entirely Blew 128 GB .The System Maight Not Boot"

Mar 29, 2011

i want to install opensuse on my new lap top i partition my hard (600gb) with 5 parts:

c: 97 gb
d: 150 gb
e: 150 gb
f: 100 gb
g: 50 gb
and 38 gb unlocated part

in opensuse instalation , the yast makes a 2gb for swap 14gb = root , 21 gb = home, but in Instalation Overview under Booting has a red error: the Boot loader Installed On a Partition that does not Lie Entirely Blew 128 GB .The system maight Not Boot;

View 1 Replies View Related

OpenSUSE Install :: Can't Boot To Single User

Jul 3, 2009

No idea why this happens but on a couple of systems I'm unable to boot into single user, either as runlevel S or runlevel 1. This is true for the Failsafe image and the regular system image alike.

The major symptom is that it seems the initrd image is started and then the system hangs when it tries to transfer control to the inittab.

I am able to boot into the system with runlevel 2 or higher. I am also able to boot into the single-user rescue DVD image.

how to add the rescue DVD boot image to my secondary IDE drive so that I have a guaranteed way into the system?

View 4 Replies View Related

OpenSUSE Install :: 11.4 Boot Fail After Install "Error Loading Operating System"?

Jul 13, 2011

I have installed openSuSE 11.4 32-bit on my PC. Installation went okay, but when I shut down the system and started later it does not load.

My computers have;
- Intel Pentium Dual Core processors
- Asus motherboards
- Onboard VGA, Sound, NW
- 2 GB DDR2 RAM
- 80 GB SATA HDD
code....

What happens is, the first screen appear (where it instructs to press DEL to go to BIOS), then the system hangs us displaying "Error Loading Operating System". There nothing works, except the CTRL+ALT+DEL. Press CTRL+ALT+DEL, same cycle repeats.

View 9 Replies View Related

General :: Change From A Dual Boot System To A Single Boot System?

Jul 20, 2010

I just recently installed ubuntu 9.10 in my upstairs computer. It is a single boot system.Downstairs I have a dual boot system. I have windows vista and ubuntu 9.10 installed. It worked fine. I wanted to make this a single boot system and uninstall ubuntu 9.10. I cannot get rid of the grub bootloade

View 14 Replies View Related

OpenSUSE Install :: Grub Does Not Boot / Just Showing A Black Screen Written 'Grub'?

Feb 26, 2010

I've been running openSuse 11.2 for a while on my notebook.Today I turned it off at work and came home. When I tried to turn it on, it boots, shows a black screen written 'GRUB' and then NOTHING. It doesn't complete the boot process.

View 9 Replies View Related

Ubuntu Installation :: Initial Boot On System - GRUB Rescue - Error: No Such Disk

Feb 11, 2010

I am fresh to Ubuntu and am having trouble getting it to boot on my system. I normally run XP, but recently added a second internal hard drive and installed Ubuntu on it. The installation went fine and upon initial reboot I received -

GRUB loading. error: no such disk grub rescue>

I am wondering if there is an issue between two different operating systems upon boot. I am not familiar with GRUB commands.

View 4 Replies View Related

OpenSUSE Install :: Red Line Of Error Msg During Boot System Console Stolen At Line: 266 SuSE11.4?

Apr 29, 2011

...../etc/init.d/before.local...System Console Stolen at line: 266 This line of red warning consistently appears immediately after something that ended with /etc/init.d/before.localThis is during the boot.Have anyone see it before ?It appears both in kernel versions:2.6.37.6-0.5-desktop2.6.37.1-1.2-desktop

View 3 Replies View Related

Ubuntu :: 10.04 Grub Install - Cannot Boot Into Original System

Jun 8, 2010

I just installed 10.04 to the second hard drive on my system, and stupidly installed the new grub to the first drive, which has my standard 9.10 OS on it. Now I cannot boot into my original system. All of the files across both disks are still intact and mountable. I'm not new to linux in general, but I'm not exactly knowledgeable, either...

View 9 Replies View Related

General :: Unable To Boot Windows / Grub Error Saying GRub Loading Stage2 Read Error

Jul 8, 2011

I am new to Linux. I have installed RHEL 5.4 on my PC with preloaded Windows XP.

Windows was set as the first boot kernel. So if i do not choose which OS to be loaded it will load Windows by Default.

Today I got an error saying GRub Loading Stage2 read error.

View 9 Replies View Related

OpenSUSE Install :: Grub Boot / Unable To Change The Boot Records On The Drive?

Aug 18, 2010

Dual Booting my laptop and unable to change the Boot Records on the drive. Not because I dont know how, but my primary OS will fail to boot(win7).

I have drive partitioned as follows...
sda1 = Win7 system (default install)
sda2 = Win7 Main (default install)
sda3 = swap
sda4 = Extension (I think thats what its called)
sda5 = / (ext4)

What I need is a boot cd or perferably Grub installed on a 256MB Thumb drive with the options to load the installed system from sda5.

View 4 Replies View Related

OpenSUSE Install :: LVM - Can't Boot Into X Window - Only GRUB Command Line During Boot

Nov 4, 2010

Out of curiosity and stupidity, I configured 2 extended partitions to LVM in gparted. Now, I can't boot into X window, and there's only GRUB command line during boot.

View 5 Replies View Related

Ubuntu :: Grub Error 15 - Couldn't Combine Two Unallocated Spaces Under Single Partition

Apr 9, 2011

i found in some thread that Swap space wasnt really necessary for RAM of over 1 GB, and true to it, i wasnt using using much of my 4GB allocated for swap ever so i deleted it ( dunno if it was wise, but didnt face any problems when i first deleted). today, i found out from another thread on a way to extend the size of /home directory if it was on a seperate mountpoint, and if space was available on my hard disk.

i just had 1 GB allocated to home directory and it used to fill up quite rapidly (due to cache from google chrome). I made a backup of my home directory contents, and i deleted the /home partition through the Disk utility. Somehow i couldnt combine the two unallocated spaces under a single partition why is that? (My plan was to combine that 1GB and the 4GB from the earlier swap space to use a 5GB home partition.) then i restarted and ever since i have been seeing the Grub error,and am not able to access my operating systems normally. GRUB Loading stage 1.5 Grub loading, please wait Error 15 . i am attaching the results.txt from my system obtained by booting through a liveCD. Something tells me that the way ive been following has been a roundabout one or a very inefficient one. how can i restore my system to normalcy

View 9 Replies View Related

OpenSUSE Install :: Boot 11.4 On Dualboot Nvdia G7600 Based System - Fresh Install "system Console Stolen At Line"

Apr 22, 2011

I tried to update one of my home machines with a fresh install. This is far from new to me so I did not expect any problem. But I was proven wrong. First: did install the system as usual. First anomaly: system blocked during the install process but did restart it flawlessly one I tried to eject the DVD from the player. It needed actually that intervention to retake working. It then went to install and froze during the first system start. I rebooted with failsafe settings, it then correctly configured. I reached a beautiful desktop. I performed the updates from the update repository and I joined the nvidia proprietary driver repository (which updated to the G02 driver).

I then rebooted the machine and now I am in trouble. In normal mode the system (dual boot Opensuse, XP) does not boot at all and freezes immediately after hitting enter as before. In safe mode it goes further but does not reach X anymore. It blocks with the following line statement: "system console stolen at line 266". I then tried "startx". But the system goes into a scrolling loop that does not allow me to read the output. how to get at least the error message of the loop? I read some line passing by that the system might have an X11 authorization problem.

Athlon Phenom X4 905e
Nividea G7600 graphic card
Former system installed and running flawlessly: 11.1

View 9 Replies View Related

General :: GRUB Boot - Error: Attempting Boot From Hard Drive (c GRUB)

May 16, 2011

we have an oracle application server on red hat 4.6 upon booting it comes up with error: attempting boot from hard drive (c GRUB)

View 2 Replies View Related

Ubuntu Installation :: Failed Install (dual Boot) Grub Error 17

Dec 4, 2010

I just tried to install Ubuntu 10.04 on my windows machine. Unfortunately there was an installation error and now the computer will not boot up in windows anymore (I get grub error 17). I had Ubuntu 7.04 before, but when installing 10.04, I deleted the 7.04 partitions. Is there a way to recover the ability to boot into windows?

View 1 Replies View Related

OpenSUSE Install :: System Boots To Grub Instead Of Kernel?

Apr 14, 2010

I installed Fedora 13 on a separate partition and it deleted all of my openSUSE entries in grub. Or the boot menu, whichever is correct. From another thread, I found these commands and tried it:

Code:

grub
root (hd0,3)
setup (hd0)
quit
reboot

hd0,3 contained one of my openSUSE installs. Everything went well and grub accepted all of these commands except quit. So I used esc and rebooted. The reboot brought up the grub shell again. I could find no way to boot anything. Then I used the 'repair installation' option from the 11.2 dvd and installed a new boot loader for /dev/sda2 which contains 11.2.

This was successful, so I went to the YaST bootloader tool and added /dev/sda3 (Milestone 5) and /dev/sda4 (Fedora) and rebooted. But these two partitions still boot into grub instead of loading the correct kernel.

View 7 Replies View Related

OpenSUSE Install :: Grub Error After Install And First Reboot?

Dec 21, 2010

I tried several times to install sue 11.3 on a amd 64 system by configuration a soft raid1 by this order:

md0 /boot
md1 /
md2 swap

or my problem, after configuration and install over the dvd and yast installation menu, after the first reboot I have a grub error -> nothing found.If i try to setup suse 11.2 over the same method, it works.after a system upgrade to 11.3 all is working fine. The only problem is by installing directly the 11.3 I also re-download the dvd and try over the netcd and it's all the time the same error.I searched in the forum but nothing found (perhaps i do a wrong search)

View 2 Replies View Related

OpenSUSE Install :: GRUB Error 17 On External HDD

Apr 9, 2011

I recently decided to try out openSUSE 11.4 with gnome and install it on my external USB HDD. To do so i followed this guide here SDB:Installation on external hard drive - openSUSE

Unfortunately after finishing the install when trying to boot into the system i got GRUB error 17. The only thing i did differently from the guide was placing the /boot partition after a ~800 GB NTFS partition with my data.

I tried to solve the problem by reinstalling the system with different settings than before. After completing all of the steps in the guide mentioned i disabled booting from MBR and enabled booting from /boot partition. Also set the installer to write generic boot code to MBR.

Though after the installation i realized that grub is not loading at all this time and went on to fix it by completing the steps here SDB:All about GRUB - openSUSE . After doing so i'm back to GRUB error 17.

View 9 Replies View Related

Ubuntu Installation :: 10.04.1 Install Fails To Boot -> Error: Out Of Disk, Grub Rescue

Jul 13, 2011

Downloaded Ubuntu 10.04.1 Desktop AMD64, tried to install it to a cleand HDD using the whole HDD, i.e. gave it permission to use the whole HDD. Installation process appeared to run OK but when it came to the restart it just fired up the message

error: out of disk
grub rescue>

I've searched this forum and found numerous references to these error messages but cannot make head nor tail of the diagnostic suggestions. Apart from anything else they suggest strings of command lines which I don't understand and can't enter anyway since they don't correspond to my keyboard layout (if I hit > or ) something completely different appears on the screen). Is there someone here who can provide a step-by-step solution in lay language ? Or is there such a thing as a bootable file which can be downloaded and inserted into my CD drive to correct this problem ?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved