I installed ubuntu 10.04, aftert that i cluld not able to start windows xp,Please find the details about my hard disk
Disk /dev/sda: 40.0 GB, 40020664320 bytes
255 heads, 63 sectors/track, 4865 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
[code]....
I am unable to load Ubuntu onto computer as dual boot or inside windows. Thus scanned the CD and found it has 23 errors.Are these files suppose to be on the CD?casper, .disk, install, install, isolinux, pics, pool, pressed, autorun, md5sum.
View 4 Replies View RelatedA few days ago I went to perform the Service Pack 1 Upgrade for Win 7. This crashed out with an error. On researching the problem I found a solution to fix the problem by marking the Windows partition as active. I did this (via Computer Mgmt -> Disk Mgmt). This allowed the SP1 upgrade to work, however on reboot I got an error BOOTMGR missing. This I rather rashly resolved by using the Windows 7 install DVD in Recovery mode to reinstall the Windows Boot manager via bootrec /Fixboot I thought I would then be able to use the Opensuse 11.2 install disk to fix grub.
I use the Opensuse install disk and select Repair system -> Expert Mode -> Install New Boot Loader then select Other -> Reread Configuration from Disk. This adds Win 7 back into the grub menu. I then select OK and get the message "the bootloader was installed successfully". The problem then comes when I click my way through OK and Next to finish the install. At the end of the process I get the message "An error occurred during the installation" and I'm no further forward.
FYI the PC has a single SATA disk installed partitioned as follows:
dev/sda1 100Mb Win System Parkition
dev/sda2 Windows NTFS
dev/sda3 Windows FAT
I managed somehow to successfully install a dual boot with Ubuntu 9.02 and Windows XP. Ubuntu was on a PATA drive and the WinXP was on a SATA drive. The SATA drive was configured to boot first. As I was having problems with Ubuntu I booted into WinXP, re-formatted the PATA drive, then restarted the computer and installed Ubuntu 9.10. It all went well.I rebooted the machine and the following message was on the screen:
GRUB Loading stage1.5.GRUB Loading, please wait....Error 17
I rebooted, changed the boot order so that the PATA disk (Ubuntu) started first, then the SATA(WinXP). Ubuntu loaded up the dual boot screen.I chose WINXP, but I was greeted with a black screen.I rebooted again and chose to load Ubuntu, which it did without a hitch.what I should do to restore my access to WinXP? Or should I start again? If so, how?
I have Ubuntu 10.04 LTS and Windows XP installed on my laptop. Usually when booting, I get the GRUB 2 menu and I can boot into either Ubuntu or XP.I was playing around with EasyBCD, then after trying to remove it I was unable to boot into Windows, I used a Windows 2000 CD recovery console to fix the MBR (using: fixboot and fixmbr).Now Windows starts up when I power on, but I don't get the grub menu anymore with an Ubuntu option. If I boot from the Ubuntu Live CD and try to mount my Ubuntu partition (/dev/sda5) I get this error:
mount: wrong fs type, bad option, bad superblock on /dev/sda5,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
[code]....
I have two separate hard disks, one having ubuntu 10.04 and one having Windows XP. I'm unable to get an option to choose from grub menu as to which operating system i want to boot into.
View 3 Replies View RelatedJust installed Slackware 13.37 and am trying to get dual boot to work properly. I have edited /etc/lilo.conf to point the Windows section to what I believe should be the correct partition (/dev/sda2) Here is the relevant section
Code:
# LILO configuration file
# Windows bootable partition config begins
other = /dev/sda2
[code]....
I have mounted /dev/sda2 to /ntfs-c as suggested during install and when I browse through there I see the files from my windows setup so it is in fact the correct partition. When I load Windows on boot, however, it is pointing to the recovery partition (/dev/sda1).
I had a dual boot system with 3 partitions, Windows 7 on one partition, and Windows XP on another partition and a Data partition. I decided to load Ubuntu 10.10 on the Windows XP partition.During installation I selection manual partition, and deleted Windows XP.after successful completion of Ubuntu installation "Grub" directly boots into Ubuntu, it doesn't show me the OS selection screen. After following some forum posts I did an update grub
Code:
Generating grub.cfg ...
Found linux image: /boot/vmlinuz-2.6.35-22-generic
Found initrd image: /boot/initrd.img-2.6.35-22-generic
[code]....
I have a laptop that has a dual boot of Windows7/Ubuntu10.04. Ubuntu loads fine, but Windows 7 does not. It shows up in the Grub, but it will not load. I assume that the boot loader was messed up somehow, but I am not experienced at deciphering the boot info file. I was hoping someone might be able to take a look at the file and tell me what the issue might be, and also which part of the text indicates the problemBoot File:
Code:
Boot Info Script 0.60 from 17 May 2011
============================= Boot Info Summary: ===============================
[code]...
i have just installed Ubuntu 10.10 on a pre installed windows 7 system. Ubuntu is working really well but the only problem is that when I try to boot into windows,
I get the windows sign and then I get a black screen and windows does not load. It seems to be an easy problem to solve because I can actually boot windows 7 in
safe mode with no problems at all! The problem is there when I try to boot windows 7 normally. To be honest I only need windows for a project that uses MSQL server.
I'm having installation issues with linux. I'm trying to set up a dual boot with vista and linux. I prepared my computer by backing up my files and partitioning my hard drive, leaving 20GB for linux. I downloaded Linux Mint 7, and booted from USB (using the universal USB installer from pendrivelinux.com). All good, entered into linux and installed by following the prompts (selecting use largest unallocated partition to point linux to the partition). At this stage the screen cleared to just leave me with the desktop background.
I patiently waited for it to reboot which never happened. So I waited for 20mins or so, then shut the computer down because I couldn't think of what else to do. When I restarted (without using the livecd/usb) it just went straight to vista. I did a bit of reading and found it might have been something to do with vista taking over grub, and some of the tutorials suggested downloading EasyBCD. So I did that, here's the summary:
Code:
There are a total of 2 entries listed in the Vista Bootloader.
Bootloader Timeout: 30 seconds.
Default OS: Linux Mint 7
Entry #1
Name: Microsoft Windows Vista
BCD ID: {current}
Drive: C:
Bootloader Path: Windowssystem32winload.exe
Windows Directory: Windows
Entry #2
Name: Linux Mint 7
BCD ID: {default}
Drive: C:
Bootloader Path: NST
st_grub.mbr
Code:
Windows Boot Manager
identifier {9dea862c-5cdd-4e70-acc1-f32b344d4795}
device partition=C:
description Windows Boot Manager
locale en-US
inherit {7ea2e1ac-2e61-4728-aaa3-896d9d0a9f0e}
default {bbf9569e-31e5-11df-a844-91f7867d7949}
resumeobject {3fb6bf64-700d-11db-8409-0016d303c867}
displayorder {3fb6bf63-700d-11db-8409-0016d303c867}
{bbf9569e-31e5-11df-a844-91f7867d7949}
toolsdisplayorder {b2721d73-1db4-4c62-bf78-c548a880142d}
timeout 30
Windows Boot Loader
identifier {3fb6bf63-700d-11db-8409-0016d303c867}
device partition=C:
path Windowssystem32winload.exe
description Microsoft Windows Vista
locale en-US
inherit {6efb52bf-1766-41db-a6b3-0ee5eff72bd7}
recoverysequence {572bcd55-ffa7-11d9-aae2-0007e994107d}
recoveryenabled Yes
osdevice partition=C:
systemroot Windows
resumeobject {3fb6bf64-700d-11db-8409-0016d303c867}
nx OptIn
Real-mode Boot Sector
identifier {bbf9569e-31e5-11df-a844-91f7867d7949}
device partition=C:
path NST
st_grub.mbr
description Linux Mint 7
Now when I turn my computer on, I get options for vista and linux. Vista works fine, but if I select Linux Mint 7 I get an error that reads "cannot load from harddisk, insert systemdisk and press any key".
I have just installed Ubuntu, now when logging into my laptop i am able to sucsessfully load ubuntu but i am unable to load the original OS (windows 7).
The grub 1.9 bootloader gives me the option
When selecting this option it goes to a black screen with a - in the top left of the screen then the grub screen re-appears
I have ran the boot_info_script.
Code:
Boot Info Summary:
I have two hard disks sda and sdb. I have Windows XP installed on sda2 and Ubuntu 10.04 on sdb5. When I installed Windows XP, Ubuntu stopped booting. I tried to repair grub2 from a Live CD unsuccessfully. Now I have completely messed up my MBR of both HDDs. I just want to configure grub2 to load both OSes in dual boot mode.
View 9 Replies View RelatedI had 9.10 installed and I did an upgrade to 10.04. However I cannot see anymore my Windows Vista partition with grub.. I have a Toshiba laptop Satellite p305.This is my boot script output:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in [code].......
After installing karmic with Grub2 I am unable to boot into Archlinux partition. Grub2 has removed the last line of the Archlinux boot stanza! It used to read:-
[Code]....
Following the Grub2 tutorials I have tried editing /etc/grub.d/40_custom as follows:-
[Code]....
But no luck. Only way into Archlinux is to get into the edit shell and manually add the missing line and remove other stuff not needed. I have spent hours trying to resolve this issue and I am fairly p----d off
I just did an upgrade from 9.10 to 10.04 and now I can't boot into Windows 7 on this dual boot desktop. I usually do a clean install but with a laptop and desktop a copy of Windows 7 and Ubuntu on each machine it's getting very tiring with 4 os's so opted for the upgrade this time.
During the installation there was a window that game up about upgrading grub and what devices to install it on. The help box was not very complete and seemed to say to click all the check boxes which included the main drive and it's partitions including windows. During the install somewhere it said something like grub could not be installed on one of the devices which I think was sda6 which is probably the Windows 7 partition.
So how would I get the option of booting into Windows 7 on startup as now I only get a blank black screen when I click on the Windows 7 option upon bootup? I hope I don't have to reinstall one or both os's again from scratch as this is becoming to much work to do on two systems every 6 months, especially with the amount of programs I have installed.
I can only use the Live CD to operate Ubuntu. After typing in the command sudo fdisk -l, I get the following?
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
[Code]....
And when I boot without the Live CD, I get the following message in the GNU GRUB Version 1.98-1ubuntu7 window page.
I had a dual boot machine with fedora 12 and windows vista and I could use grub boot-loader to switch between two. Few days ago windows got corrupt and I have to reinstall it. I put windows 7 now and as usual it erased grub. So to reinstall I put the fedora 12 installation CD on and followed some usual setup steps. When I got the command line I issued the command "grub-install /dev/sda" (sda not hda because It showed bunch of sda, sda1..) but surprisingly it said grub command not found. I remember doing it before while it worked fine.
View 4 Replies View RelatedI have a netbook running Windows XP as standard. There is also a recovery partition which came from the factory.
In the past I installed Ubuntu (I think 9.something) from USB key and all worked fine. However my XP became corrupted and I needed to do a repair on it. After this, Ubuntu became removed from the boot select menu.
Since then, Ubuntu has become updated to 10.04, which I now cannot install.
The Live CD tells me there is a "file IO error" and simply stops installation at around 70%.
I did manage to get into Ubuntu from a Live USB using Wubi. However when I chose to install Ubuntu to a Harddrive, the option to "install side by side" was missing.
After reading on the forums, I did a chkdsk /f on Windows and tried again. Now my liveUSB does not show a boot menu!
When I select to boot from USB stick, the screen goes blank with a flashing cursor. Ctrl+alt+dlt reboots.
I'm really lost here! It seems when I fix one problem, another problem arises!
Also when trying to instal Ubuntu within Windows, the process goes through to 100% and asks me to reboot. When I do so, the option for Ubuntu does show in the boot menu. However when I select it, I get an error "Windows boot failed: file wubildr.mbr and status: 0xc00000f - something is corrupt".
I have just installed Ubuntu 10.4 x64 onto a machine with Vista Ultimate x64. When I boot the machine, the Windows option comes up in the GRUB menu. However, when I attempt to boot Windows, I receive the following error: No such device: de80ab9f80ab7d21. error: No such partition. Press any key to continue...
I looked around and found a similar issue at [URL] However, before trying to fix the issue by guesswork or via solutions that worked for a similar, though not necessarily identical problem. I've run the boot info script (see output below) mentioned several places on this site as a valuable input for boot problem tracking. how to get Windows to boot on my computer?
[Code]...
I'm trying to dual boot Win7 and Ubuntu WITHOUT using Grub. This is to support Bitlocker encryption.
I followed this guide, and now when I select Ubuntu I get a Grub> prompt and no ubuntu.
I feel like I'm halfway there, I just need to get Grub to load correctly or something.
if having a boot partition is recommended for dual boot installation of Ubuntu 10.04 and Windows 7 and why?
View 1 Replies View RelatedI am trying to install Ubuntu on a machine that already has Windows 7 on one partition. Obviously I intend to install it on the other free partition. So I downloaded the iso burnt it onto the disk and pop in the disk and the boot the machine. The installation screen comes up I selected the first option (Try Ubuntu without installation), I just see a prompt after a few seconds and then the screen goes blank and nothing happens. Unable to detect a signal, The monitor goes into standby. The same thing happens if I use "install Ubuntu" option as well. I downloaded minimal install version Ubuntu and tried to install with that. since its old school installation, the installation completed without any errors, but when I restart the grub come up and when I select to boot into Ubuntu, I see the same behavior i.e. the screen goes blank and never boots to anything. This is a machine on which I was using 10.4 until yesterday.
View 1 Replies View RelatedI just got a Toshiba Mini NB305-310 and tried to install Ubuntu 10.04 on it using the .iso file on a flash drive. When I try to boot into Windows XP, the loading screen comes up for a second, flashes blue, then restarts the computer. I'm able to boot up in Ubuntu, but it takes a LONG time with the screen black before it goes to the Ubuntu loading screen. I saw in an earlier post that it's helpful to post the output of the Boot Info Script, so I've posted it below. I'm new to the forums, so if I'm doing anything wrong, please let me know:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in
partition #5 for /boot/grub.
[code].....
I am trying to run a dual boot system with Windows 7 and an Ubuntu 9.10 installation from a live CD. I am running this on a Dell Inspiron M5030. Both operating systems have installed fine however whenever I run Windows the computer subsequently fails to run Grub upon rebooting and gives the following error message:
Grub loading
the symbol 'ob_bioslgrub?+E?U? Not found
Aborted press any key to exit
The unrecognised symbols are different each time. I have also had (' ') and ('ee*??S ') and ('un'). I cured this initially by reinstalling Ubuntu but after looking at the support documentation have now found that I can cure it temporarily by simply reinstalling Grub using the command:
sudo grub-setup -d /media/dd5d6cd6-cb80-40e0-baf3-13ae1ebe17a4/boot/grub -m /media/dd5d6cd6-cb80-40e0-baf3-13ae1ebe17a4/boot/grub/device.map /dev/sda
I can then run Ubuntu fine, however upon running Windows again the problem reoccurs and Grub will not run.
I have a fairly old Dell Dimension 8400 with two disks. I have Windows XP on the first disk (750GB) and have a second unused 200GB disk that I installed Ubuntu 10.10 onto.
Here are the problems I had:
1) After the install, the computer would only boot into Linux. I had no options at all at boot up for which OS to boot into.
2) I verified that my 750GB WinXP disk was still intact (/dev/sda). I tried created a file for WinXP in /etc/grub.d taken from the 40_custom file. I added a menuentry section to it and ran grub-update. grub-update complained about an error ddf1 invalid # of disks in RAID partition.
3) Ubuntu didn't seem to know about my Linksys AE1000 wireless adapter. And since I has no Wireless on the computer, I couldn't download drivers.
4) I rebooted the computer after trying to update grub and now my PC boots into Windows again.
I expected to install Ubuntu and then have grub2 give me a choice of WinXP or Linux. Why did it intitally boot only into Linux, and why did it strangely revert back to WinXP later on?
I just set up a dual boot on a system with fedora 12 and XP. XP in on one hard drive (sda) and Fedora on a second hard drive (sdb).
I installed grub on the Fedora disk so as to not touch the windows disk at all.
Prior to installation, in the bios, I set the Fedora disk (sdb) first in the boot sequence, and then XP (sda) so that the grub loader would boot up by default. (If I set the windows drive first then the system bypasses grub and loads straight into windows.)
My system can now boot up into Fedora fine, but if I select windows from the grub loader menu I just get a blinking cursor - windows will not boot.What do I have to do so that grub can boot into XP?
I installed Ubuntu 11.04 on a separate partition, with Grub being in it own partition. When I start the PC only windows Xp is available. So how do I get grub or Ubuntu load with windows xp boot loader? I tried with Live cd, the sudo grub but then it says command not found. I think its because Ubuntu 11.04 uses grub 2.
View 1 Replies View RelatedI have a 160 GB hard disk with three partitions (All NTFS):
C: (30 GB) (WINDOWS XP system partition)
D: (60 GB)
E: (60 GB)
I want to install Ubuntu on another drive (D: in this case). I have backed up all my data on D: drive. What are the steps in doing so and does Ubuntu support NTFS? If it does then will I be able to read and move data between all the drives without any problem (while running either of operating systems)?
I tried to set up a dual boot system on two separate hard drives. I installed Windows XP first (because doing so in past experience has made it easier) on the PATA 20 GB hard drive configured as slave on the first IDE channel. Then I installed Ubuntu 9.10 on the PATA 80 GB hard drive configured as master on the first IDE channel along with an NTFS partition on this drive:
[Code]...
