I would like to recover my grub installation in a dual boot system. if there is an easy way to recover grub using flash disk? If yes is your suggestion opensuse developed? (currently running 11.3) . It would be nice also to have some gui just to make things easier. If not I assume that then the only option is the boot from dvd. Is that right?
View 9 Replies
I am currently rebuilding a couple laptops and a desktop to dual boot Windows and Suse 11.2. Windows is installed on partition 1. On the laptops, the build goes fine and dual boot with grub is OK. No issues. But on the desktop, the exact same build (after all the on-line updates, etc) fails with "Operating system not found" on the final (and first) boot. It seems that the Suse 11.2 build is somehow resetting the active partition and the boot does not see grub or Windows. When I reset partition #1 back to "active, only Windows loads. So I guess I need to fix this by reinstalling grub. Or use the Windows boot loader.
(1) Where is grub located on my system?
(2) What partiton is the Linux master Boot record If I wanted to use the Windows boot loader and do the following command to grab the 512 bytes I need:
dd if=/dev/sna? of=grub.bin bs=512 count=1
My partition layout is below. This is output from gdisk.exe in DOS7. It's an 80gig drive.
1 = Windows-7
2 = /boot
3 = swap
[code]....
I did a fresh install of SuSE 11.4 (WIN7 TOO) and changed my Larger HD1 to the first HD. I was installing and got this error first: the boot loader is installed on a partition that does not lie entirely below 128GB The system might not boot if BIOS supports only lba24 (result is error during install grub mbr) status loc dev/sdb6
I continued with the install and then got:
Yast2 error occured
while installing GRUB ver 0.97 (640k lower/3072k upper memory)
[minimal bash-like lineediting is supported? for the first word, TAB lists possible command completition anywhere else TAB lists possible completion of a device/filename]
grub setup --stage2=/boot/grub/stage2 --force4-lba (hd0,5) (hd0,5)
Error 25
disk read error
grub> quit
My laptop setup is:
sda1: W7
sda2: FAT16
sda3: /boot
sda4: encrypted LVM with debian (everything besides /boot)
now I've re-installed W7 so grub was overwritten. I've tried the procedure which worked for me previously:booting with the netinst usb in rescue mode, choosing a root partition to mount, using grub-install to reinstall the grub:
Code: Select allmount /dev/sda3 /boot
grub-install /dev/sda
Now I'm on Jessie (stable), and this time this fails, and I am able to mount only sda3.grub-install doesn't exit so I'm assuming it has been replaced by `grub-installer'. also '/boot' doesnt exist so I created it manually.
Code: Select allmount /dev/sda3 /boot
grub-installer /dev/sda
The latter fails with
Code: Select all/dev/sda/proc not a directory
I have a dual boot Acer Aspire One, after reinstalling Windows back to "original factory", the way it was straight out of the box, it now will not boot up at all. It goes to the Windows start screen goes blank, and loops there infinitely. Is there a USB tool I can use to figure out what went wrong and recover either my Windows or Linux partition with out having to do a complete reinstall?
View 1 Replies View RelatedI resized my windows c drive to make another drive which also has Open SUSE 11.4 dual booting which was working fine.
After reboot I get missing operating system so I boot the live Opensuse DVD and the windows and Linux is still there so I tried the boot configure tool in YAST but get the error because of partitioning the boot loader cannot be installed properly
Can I make a boot floppy somehow? I now have a grub menu when it boot sup but do not know what to do now
I started another thread about this to get help booting into openSUSE after Fedora rewrote my bootloader and deleted all other entries. I managed to fix it but I never did find out why the following commands caused my system to boot to the grub shell instead of the grub menu.
Code:
grub
root (hd0,3)
setup (hd0)
quit
reboot
Can anyone explain to me why these commands caused my system to boot directly to a grub shell? It's as if there were no /boot/grub/menu.lst files for it to use, but after I got everything back to normal, the files were still there.
If it helps, this is how the drive was setup before and now, except Fedora was on /dev/sda4 and has since been deleted.
Code:
Device Boot Start End Blocks Id System
/dev/sda1 1 262 2104483+ 82 Linux swap / Solaris
/dev/sda2 263 13316 104856255 83 Linux
/dev/sda3 * 13317 14621 10482412+ 83 Linux
I am trying to Dual-boot Windows & and OpenSUSE 11.4, and have run into walls all over the place. Here is what I did:
1. Windows 7 was already installed. (Don't like it, freezes all the time)
2. Installed OpenSUSE using default partition options.
3. Booted into OpenSUSE with no problem
4. Tried booting into Windows, no joy.
5. Got that figured out, now I can get into Windows.
6. GRUB is gone, so now I can't get back into OpenSUSE.
I saw a good quick fix for grub after win 7 updates over here
My question is, after WIN 7 sp1 it seems every update win 7 does borks grub and resets the system to boot from the Win 7 boot partition, Is there a way to prevent this or is it going to be a boot from CD and repair after every update?
Cause I know M$ isn't going to want to fix it as they don't like sharing systems.
I'm running
OpenSuse 11.4 Win 7 sp1 dual boot
I dual booted opensuse along with vista. I installed opensuse in extended partition, with grub and gave the option as "boot from extended partition". Now everything is fine. I am able to boot into suse as well as vista. Now how can I restore my vista bootloader? I want to uninstall openSuse. When I try restore mbr from hard disk. There is absolutely no change!
View 1 Replies View RelatedI had dual boot PC (openSuse 11.3 / Windows XP). Then I had to reinstall Windows XP, so I lost dual boot capability. (No Grub boot options screen, directly Windows boot.)How can I reinstall Grub (only Grub)?I tried by booting with the openSuse installation DVD, but no repair option appears as in older versions.
View 5 Replies View RelatedA few days ago I went to perform the Service Pack 1 Upgrade for Win 7. This crashed out with an error. On researching the problem I found a solution to fix the problem by marking the Windows partition as active. I did this (via Computer Mgmt -> Disk Mgmt). This allowed the SP1 upgrade to work, however on reboot I got an error BOOTMGR missing. This I rather rashly resolved by using the Windows 7 install DVD in Recovery mode to reinstall the Windows Boot manager via bootrec /Fixboot I thought I would then be able to use the Opensuse 11.2 install disk to fix grub.
I use the Opensuse install disk and select Repair system -> Expert Mode -> Install New Boot Loader then select Other -> Reread Configuration from Disk. This adds Win 7 back into the grub menu. I then select OK and get the message "the bootloader was installed successfully". The problem then comes when I click my way through OK and Next to finish the install. At the end of the process I get the message "An error occurred during the installation" and I'm no further forward.
FYI the PC has a single SATA disk installed partitioned as follows:
dev/sda1 100Mb Win System Parkition
dev/sda2 Windows NTFS
dev/sda3 Windows FAT
I wish to add more OS to my dual boot system with suse (sda) and windows7 (sda). The plan is to add Linux Mint(sda), PC BSD (sda), Fedora (sdb) and Solaris (sdb). I wish to remove grub2 from mint and install grub legacy, not sure whether it will work or not. I will be reinstalling grub from suse dvd. It gives me a free hand for adding boot entries. I wish to know whether I can remove grub2 and install grub legacy. In grub2 all boot related folders are stored in more than 1 place like /boot and /etc and subfolders.
View 9 Replies View RelatedI'm trying to install OpenSUSE 11.4 (64bit with the server options included) on my Mac (Core 2 Duo 2.0 Ghz with 2 GB memory). So I have sda2 the OSX, sda1 swap, sda3 is the bootcamp (windows), sda4 (ext4) and sda5(ext5). I installed rEFIt 0.14 first, then I reboot with DVD on. The installation setup resized the Windows partition from Bootcamp, and create 3 other partitions (the sda1,4 and 5). At the installation I choos MBR enable and "/" as home enable.
At the end of the installation I have the error about MBR, that can't mount, or create the mount point? I'll double check the exact message. Anyway, when I try to load OpenSUSE, is not working: can not load the system. I tried to find on the installation menu a repair (I thought that I can find an utility to fix the MBR). I don't want to choose other distribution, because I used SuSE before, and I really like it, and of course this way I can learn more about troubleshooting a Linux installation on different environment
I would like to remove openSUSE (11.3) from my dual boot (/Windows) system. In the old days, the install CD used to have an option for that, but now my DVD doesn't have anything, or perhaps I overlooked?
View 7 Replies View RelatedI'm having serious troubles to install ubuntu-10.04.1. My raid is an hardware raid with intel chipset. Note that win7 is already installed and working with my raid. I made some space from windows, to install Ubuntu (40gb). First, I run the installer, everything seems to be fine. I choose to install Ubuntu were there is the most space free (sorry, I'm not sure about the real terms used there).
Then my partition with the vista loader appears. So the installer can see my raid, and should work fine (everything is detected correctly). But once I'm in the end of the installation (around 95%), a pop-up appears, and tells me that Grub can't install in /dev/sda and it's a fatal error. I can choose an another destination, but it doesn't seems to work.
I just tried to install Ubuntu 10.04 on my windows machine. Unfortunately there was an installation error and now the computer will not boot up in windows anymore (I get grub error 17). I had Ubuntu 7.04 before, but when installing 10.04, I deleted the 7.04 partitions. Is there a way to recover the ability to boot into windows?
View 1 Replies View RelatedI installed Windows 7 and then Ubuntu 10.10 64 bits. The Ubuntu installation went fine but when rebooting a "check disk" appeared and since then my PC keeps booting directly on Windows. I tried all the GRUB reinstallation methods of the GRUB2 Community Documentation with the live CD but none worked.
Below is the output of the Boot Info script found on several threads.
[Code]...
Gnome is falling apart and I've had a lot of nagging problems that I couldn't overcome.I'm thinking of wiping the OpenSuse partitions and doing a clean install without wiping the windows partition.I initially setup using the 11.0/XP dual boot FAQ in the How To forum.I have my Home directory backed up on an external HD. Might try KDE next go-round or KDE & Gnome as separate users. I have 11.2 i586 installation DVD.
View 2 Replies View RelatedI just installed SUSE 11.2 as dual-boot with WinXP on an older system that has a 160GB PATA drive and a 500GB SATA RAID drive. I left about 80GB on the PATA drive unpartitioned to accommodate SUSE. During the initial installation attempt, SUSE was determined to install on the RAID drive instead of the PATA drive, so I disabled the SATA drivers in the BIOS to force the installation on the PATA drive. This was successful, but now there is no access to the RAID drive from SUSE because there is no driver and it is not mounted. I reactivated the SATA drivers in the BIOS and the RAID drive reappeared in WinXP with everything intact. The SATA drives now appear in SUSE under Hardware Information as "/dev/sdb" and "/dev/sdc" and the listed driver is "sata_sil".
So how do I get the RAID drivers installed in SUSE and then mount the drive so it can be browsed/modified from Dolphin? I would also like to be able to browse/change this drive from other computers on my home network through samba, just like with WinXP.
I recently bought a portable with a Windows 7 system.I want to install openSUSE 11.3 but I also want to keep Windows 7 - so I need to install a dual boot system.On my desktop I have GRUB with Windows XP and openSUSE 11.3 and all works fine.How do I proceed ? I did not find much documentation yet, but maybe I looked in the wrong places.
View 7 Replies View RelatedI have a dual boot laptop with OpenSUSE and Ubuntu. The boot loader used is Ubuntus Grub that came with the Ubuntu installation.
I have done a zypper dup and upgraded to OpenSUSE 11.4. When I reboot my system I can no longer boot into OpenSUSE, Grub says something about a missing kernel.
I think I understand whats wrong here; the OpenSUSE entry in Grubs table hasn't been updated with the changes brought in by the zypper dup (new kernel i guess).
I'm I correct to assume this? How do I fix the problem? Booting into Ubuntu I tried to find /boot/grub/menu.lst to examine it by I cannot find it. I know Ubuntu use a newer version of Grub, does it have a different file layout?
So heres the thread i had a while back ( url) that had you guys help me setup the pretty standard dual boot of Win 7 and Ubuntu. I have 2 hard drives, main one (640gig) and backup (80gb). I have Win7 installed on the 640 and ubuntu on the 80.
So i have tried installing the SP1 twice today and it has failed. When i click on details on why it failed, it says: url
I can only imagine that this has to do with my Dual Boot. Is there anything i can do or am i stuck? I THINK that my grub and master boot and all that was on the second hard drive and it is the first drive in line to boot up...so i thought i wouldnt have any issues. Not totally sure though.
Im tempted to just remove Ubuntu, its cool to say i have it, but i honestly havent loaded up onto it more than 5 times since i installed it. When you have windows already...its near impossible to want to get onto a free OS that doesnt have the codecs or programs and im not familiar with it. If it was all i had though, (aka didnt own Windows) then obviously it would be my main OS and im sure id love it and have is customized and perfect.
I've installed Ubuntu on my new desktop alongside Windows 7 (each OS is on a separate drive), I seem to have run into a small problem. Let me start with what I did:
- Unplugged 1TB drive from the PSU, BIOS was not seeing my formatted (and thus empty) 500GB drive and I couldn't put it into the boot order at all with the 1TB turned on.
- Loaded up the boot CD and was able to install Ubuntu 10.1 on my 500GB drive.
- Did a bit of configuring, shut my PC off and plugged my 1TB (with Windows 7) drive back in. I tried to see if I could now see my Ubuntu drive in BIOS but nothing is there - just the Windows drive is in the list of available drives to boot from (along with DVD-ROM and USB).
This is where I've run into my problem. What I want is to have a nice GRUB boot menu at the start like any other dual-boot system but just have the two operating systems on separate drives altogether.I did it this way because I was having issues with the advanced partition menu on the boot CD so just went ahead and followed the KISS method by unplugging the Windows drive.
I was told by a friend that if I put my Ubuntu drive into the first position in my boot order and the Windows drive in the second, then I could boot into Ubuntu and run a GRUB update command (he told me to google it) and that would create the necessary GRUB that had the entries for Windows 7 and Ubuntu.Both operating systems are 64-bit, I imagine that might make a difference in whatever help you guys can offer me. I love the hell out of both OS's and want to be able to use them interchangeably.
I have just downloaded Ubuntu 11.04 and am trying to install it on a dual boot system with Windows Vista. I get as far as "Allocate drive space" but there are no partitions to choose from. I currently have Windows and Linux Mint on the hard drive and want to install Ubuntu in the same partition as Mint to overwrite it.
View 9 Replies View RelatedThis is the third time I try unsuccessfully to install Debian as a second OS on a hard drive. When it gets to the end of the installation process the installer asks whether I want to go ahead with the Grub Boot Loader, I choose yes. The end result is however that I can't boot that partition within the hard drive -- i.e., Debian. Can someone tell me what is going on? Should I not use the Grub Boot Loader when I have more than one operating system on a machine? Should I not install Grub on the Master Boot Record (MBR)?
View 3 Replies View RelatedI have a single boot system that was working great until this morning when it locked up. I was working as I always do when the system stopped responding completely. CTRL+F1 did not work to allow me into the back so I could log in and see what was happening.
CTRL+SHIFT+SysRq did not recover the system or interrupt what ever was causing the lock up.
SSH from another system failed as the client did not respond
So I had to do a hard boot and when I did I got this:
GRUB Loading stage1.5.
GRUB loading, please wait...
Error 17
Again this is a single boot system no Windows other than in VMWare inside the install. It is a multi drive with RAID set up workstation that I have at work. The short of it I am sole IT support as our companies ITS will not support Linux. In 5 years of operations with Linux at work this is my first issue, and I can't figure it out. I already tried the PartedMagic solution (ref = Re-Install Grub Quickly with Parted Magic) and that didn't work.
I re-installed the system completely even going to the extent to change my partition scheme just to make sure that wasn't the problem (which doesn't make sense as the system had been running for 46 days non-stop without a problem). Upon reboot after performing a complete security update I got the Error 17 message again.
Below is the output of fdisk -l
Code:
Welcome - Parted Magic (Linux 2.6.30.6-pmagic)
Most of the filesystem tools and partition programs featured by Parted Magic include man pages. To read a manual page, simply type man and the name of the tool. (Examples: 'man ntfsprogs' or 'man fdisk')
[Code].....
I noticed that after making my build in suse studio my system freezes immediately after GRUB ( Normal or Failsafe) boot splash screen. I also noticed that this happens only with the specified kernel below. I'm not sure when using Kernel 2.6.37, one had the same problem. I never used it. The original kernel 2.6.34 had no problems such as the one I have described. My systems has no further problems only that it takes several restarts to go past the "Freeze". Below is a list of my system specs:
openSUSE 11.3
Kernel-pae 2.6.38.2-4.1 from Kernel Stable.
GRUB 0.97-174.1 from openSUSE 11.4
Upstart 0.6.5-33.1
xorg-x11-server 7.6_1.9.3-142.1 from X11:xorg 11.3 repo.
The GRUB from openSUSE 11.4 has been very stable and non-problematic. I will be buying an Intel core i5-2500K in a few months that's why I need the latest kernel and XOrg-X11-server. What could be causing the freezing?
So my computer has ubuntu 9.10 installed 1st and I want to install win 7 in a separate partition. Basically, ubuntu 1st, win 7 later so far from what I learned from search results, grub 2 have problem with win 7 installed later and what was recommended was install win 7 before ubuntu. how ever I do not have the time to start over again because there are too many things to back up or install again. can I simply revert grub 2 to grub 1 again and resolve the problem?
View 7 Replies View RelatedI want to set up grub for a dual boot system of xp and vista. The thing is that I have vista installed and would have to install it ance again after setting up XP in order to use the microsoft bootloader. And secondly I slowly want to get into linux...
This is how I tried it: I have four partitions on my HD and want to install the Bootloader on /dev/sda3. I started up the ubuntu live cd, mounted partition3, opened the console and tried this command line which I found in a tutorial
grub-install --root-directory=/media/hda3 --recheck /dev/hda However I get the following error message:
mkdir: cannot create directory '/media/hda3/boot': No such file or directory
