When I try to instal the rpm I downloaded from canons support website after authentication the install process fails with the following error report: [PK_TMP_DIR|dir:///var/tmp/TmpDir.kLgXId] Repository already exists.
I believe the packages I download (cnijfilter-common-3.40-1.i386.rpm and cnijfilter-mp250series-3.40-1.i386.rpm) are fine--not corrupted.
I recently upgraded (fresh installed) from OpenSUSE 10.3 to OpenSUSE 11.3. One thing I noticed missing was support for my Canon MP600 printer. Searching around, I found a solution on a Finnish OpenSUSE support page (which I translated with Google):
Canon MP600 ei asennu
Here's the fix:
1. Download file Linux_Print_Filterv270.tgz from Canon Print Filter for Linux (rpm)
2. Unpack with: tar xvzf Linux_Print_Filterv270.tgz (this also has support for other printers, including MP610, MP510, IP3300, and IP4300).
3. Install cnijfilter-common-2.70-2.src.rpm
4. Install cnijfilter-mp600-2.70-2.i386.rpm
This errors out with missing dependencies:
# rpm -Uvh cnijfilter-mp600-2.70-2.i386.rpm
error: Failed dependencies:
libgdk-1.2.so.0 is needed by cnijfilter-mp600-2.70-2.i386
libglib-1.2.so.0 is needed by cnijfilter-mp600-2.70-2.i386
libgmodule-1.2.so.0 is needed by cnijfilter-mp600-2.70-2.i386
libgtk-1.2.so.0 is needed by cnijfilter-mp600-2.70-2.i386
libpng.so.3 is needed by cnijfilter-mp600-2.70-2.i386
libxml.so.1 is needed by cnijfilter-mp600-2.70-2.i386
5. I forced the installation using
zipper install cnijfilter-mp600-2.70-2.i386.rpm
Then select option "2" (break dependencies):
Solution 2: break cnijfilter-mp600 by ignoring some of its dependencies
Choose from above solutions by number or cancel [1/2/c] (c): 2
and it installs perfectly.
6. If you're using 64-bit openSUSE Linux (as I am), you need to copy the print filters:
mkdir -p /usr/lib64/cups/filter && cp -p /usr/lib/cups/filter/* /usr/lib64/cups/filter
7. Install the printer as usual.
I selected the MP610 CUPS+Gutenprintv5.2.4 simplified driver for my MP600 and printed a test page. The MP610 drivers work for MP600. There are about 4 of them, and I didn't try the others, but my guess is they will work also.
1st. I still haven't got a reliable working printer driver direct on linux.
2nd. I am currently using the driver via smb to a windows box.
Okay there is no x86_64 driver for the capt drivers, that I could find. But you can download the standard linux drivers, which also contain the source.
The easiest way to get a 64bit driver is to unpack the drivers.
You will find a directory Src. In there are two source packages.
Copy both to /usr/src/packages/SOURCE
unpack both in a temporary directory.
I can't say which other packages you need to compile and build all of this, but you will need the c++ compilers, and various -devel packages. I would just add them via yast as you go along.
Anyway off to work out how to get this working directly on linux reliably.
I need to install the driver and I downloaded the Canon install package. The instructions read:
# rpm -ivh [file name of common module for CUPS drivers]
This rpm package construct was used in the Fedora distro.
Does it also work in openSUSE?
The only other construct given was for a deb package.
I looked in YasT for the driver but it was not there.
I ran into a problem that seems to be related to: [URL] with an HP Desktop. The desktop has a Intel 82567LM-3 on board gigabit ethernet adapter which on a fresh install of 11.3 would not operate properly. The e1000e driver was properly detected however on loading, the ethernet interface was never initialized. My solution was to get the latest e1000e driver from intel.com: Network Adapter Driver for PCI-E Gigabit Network Connections under Linux*
[Code].....
I tried to install the ATI proprietary driver for an HD 5800 (Catalyst for Linux 64 bit, v. 10.8). The two main instruction sites are:
SDB:Configuring graphics cards - openSUSE
SDB:ATI drivers - openSUSE
I chose the hard way method. I downloaded the driver. Restarted SuSE 11.3 in mode 3. And as SU followed the method above, including adding the zypper programmes (which found some already installed and which installed a whole lot more). When I then attempted to run the install (sh ./atidriver-install-10.8-x86.x86_64.run) and selected automatic mode. It completed 82% and stalled attempting to install "Postprocessing Kernel Module".
I pressed control c to kill the process and attempted to re-install using the manual mode and then using the build mode. In both instances, same outcome. When I rebooted, and entered my password, the desktop did not load but sent me back to the username/password page. I can't get back in. Does not matter as I have backed up my docs.
I decided to install the proprietary driver because the colours on the desktop corrupt after the 2nd boot following a clean install. i.e. on the initial boot the colours are fine. Second, this is the 3rd effort I have made to install the driver after a clean install of SuSE 11.3 and there is no change in outcome. So, my question: anyone any suggestion what is going on and how I can install the driver successfully? Or, do I not understand the new regime in SuSE 11.3 and should I not attempt to install a new driver.
I have spent ages looking at similar problems but not not quite the same. I have installed 11.4/Gnome (x86) and wanted to use my GT430 card. I went here: 'http://en.opensuse.org/SDB:NVIDIA_drivers' and used the 'one click' install for current cards. All went ok until I rebooted and I got a 'gdm[1239]: WARNING: GdmDisplay: display lasted 0.846578 seconds' message. I got five of these in succession until the 'gdm[1239]: WARNING: GdmLocalDisplayFactory: maximum number of X display failures reached: check X server log for errors' appeared and it popped me down to an init 3 login.
So, I deleted the blacklisting conf file so that I could get back in to Gnome on Nouveau (which I did ok). I then noticed there was no /etc/X11 Xorg.conf file so I ran /usr/lib/nvidia-xconfig to generate one (which it did) - but it made no difference. I am at a loss know after spending 8 hours on this. Any pointers would be greatly appreciated. My machine is still at fresh install state so even if I have to reinstall 11.4 it does not matter.
[Code]...
I couldn't find a driver for Canon i320 for Fedora 14. Is there any way to get the driver ?
View 3 Replies View RelatedWhere I can find a linux driver for my Canon ip1600 printer? I have scoured the internet and cannot seem to find one.
View 1 Replies View RelatedIn korokaa15x64 I can't install a canon mp260 combi because no driver is available. where I can find a driver for this common combi type?
View 5 Replies View RelatedDoes anyone have an idea of where i can find a driver for this printer? The system does not have one and if I try a driver for say the PIXMA MP220 which is CUPS + Gutenprint v5.2.4 [en] (actually, all the PIXMA drivers are that one) and I print the printer seems like it receives some command but nothing else happens. The printer says 'Printing from PC' and then goes back to the main screen.
View 5 Replies View Relatedi am running T43 Thinkpad box with Ubuntu 11.04. we have a canon network printer model i-SENSYS MF4570dn printer, and i am trying to install the UFR II driver which i downloaded from canon website. the problem i am facing is that when i install the driver with gdebi i receive error message saying: Dependency is not satisfiable: gs-esp.i tried to install ge-eps but it is not part of the repository for 11.04
View 7 Replies View RelatedI just bought a Canon MF4370dn printer. It comes with Windows drivers on a cd. I was able to configure it for Windows 7 but not for Linux. Where can I get a Linux (Fedora 13) driver?
View 3 Replies View RelatedI have done a fresh install of Ubuntu 8.04 on my partners desktop PC and am attempting to get her printer working, so far no luck. Ubuntu does not list a specific driver for this printer in 8.04 Printer is a Canon laserjet model L1112E according to the label on the printer itself but the printed instruction leaflet calls it a LBP 3000.Canon website offers a linux driver for lbp3000.
View 9 Replies View RelatedAs I try to install the driver for canon mp 160 driver, I realize that canon dun't open their drivers to open source. code...
I should follow something similar to http://forums.fedoraforum.org/archive/index.php/t-144423.html, right? i.e. download the rpms and rpm -Uvh in the same directory, right?
I am new to Linux and to make matters worse, am trying to install a new printer but cannot find the drivers for it. it is a cannon pixma mg 6120.
View 1 Replies View RelatedI am having a Canon 3108B printer But no driver/rpms for my fedora 9. I can going to install fedora 12. Can i download driver for this printer also? if so from Where?
View 1 Replies View RelatedMany have suggested that since Canon does not offer a Linux driver for the MX310, one could use the driver for the MP150. I tried that but found the results very sketchy. After a bit of digging, I found a driver from Canon for the MX340 which works extremely well for the MX310 and allows much better configuration. It wasn't easy to find, so here's the URL in case you want to try for yourself: [URL]
The package (located in the tar file) that worked for me is cnijfilter-mx340series-3.30-1-i386-rpm. Good luck!
where I can get a driver?This Printer worked fine with Ubuntu 10.10 and Mint 10
View 4 Replies View RelatedI am running Lucid 64bit on my laptop and been trying to install a canon printer driver LBP3200 on it. There are some comprehensive tutorials that I have been following and they worked on my desktop. However the last thing I have to do is
Code:
sudo update-rc.d ccpd defaults 50
which gives me the error
Code:
update-rc.d: warning: /etc/init.d/ccpd missing LSB information
update-rc.d: see [URL]
System start/stop links for /etc/init.d/ccpd already exist.
I checked in /etc and I do not have the rc.d dir! I have rc0.d through to rc6.d and rcS.d dir, but no rc.d one. Is this normal? and if so how can I get the correct file to start/stop the ccpd daemon for the printer? At the moment the print command brings up the printer icon for about ten seconds and then it disappears and nothing happens.
I have a Canon PIXMA iP1200 and Ubuntu does not recognise it. Need a driver for this printer?
View 6 Replies View RelatedI'm using Ubuntu Lucid Lynx 10:04 64 bit, with kernel 2.6.32-24-generic, and want to use my printer Canon iP1880. I've tried looking on the internet and found: the use of 32 bits drivers for Linux on Linux 64-bit platforms. I've followed the procedure given but still failed to run the printer properly. There may still be the wrong procedure that I did, could you help me again to repeat what procedures I need to do, till now,I still don't know how to uninstalling that drivers? Are there other ways that may be successful so I can use my printer, if I practice?
View 1 Replies View RelatedDid some one solved the problem how to install Laser Printer Canon LBP2900 at Squeeze? The driver (version 2.20; in the documentation stays that they were tested some of previous versions at Debian 5.04 or like) I found at the Canon's site doesn't wish to be installed at Squeeze, but somehow I succeeded at Ubuntu 10.04 and Ubuntu 10.10...
View 6 Replies View RelatedI have downloaded all drivers from canon website for linux or Ubuntu . My computer find this printer which suppose to be the right one but nothing happen ? usb://Canon/iP2600%20series. do I need more drivers or files to work in Ubuntu ?
View 1 Replies View RelatedI have followed the Nvidia driver guide exactly. I did not see any errors during the four-step process. However, on the last reboot the system gets as far as the fedora "f" on the startup screen and hangs. This appears completely fatal. I have tried the procedure a couple of times now and the result has been to reinstall Fedora 14 from scratch each time. I have been able to access the system files after the crash using the system rescue option on the installation disk. I am on the Gnome X86_64 installation. My graphics card is NVIDIA GeForce GTS 240.
View 14 Replies View RelatedHow to get this scanner to work with Ubuntu 10.10
It's connected and printer is working through the scanner.But i can't get the system to recognise the scanner.
I'm all new to Ubuntu, and i thought it was easy and terminal is a totally new thing to me.
Is there a workaround to get this scanner to work through graphical interface install, or is terminal wisdom needed...
I am inquiring about an error i have run into when i tried to make the driver "Ralink 2750 usb enhanced drvier". I downloaded it from this site [URL]... My wifi card according to lsusb is a 2570 Ralink Technology, Corp. 802.11g WiFi. I extract the package inside my /home/user/Downloads directory, using tar -xvf /home/user/Downloads/rt2570-k2wrlz-1.6.4.tar.bz2 That works fine and extracts the file, but once i change the working directory to /home/user/Downloads/rt2570-k2wrlz-1.6.4/Module and run the 'make' command, i receive the following error.
[code]...
I'm having issues installing the nvidia-96 driver package on the new Lubuntu 11.04. I have a GeForce4ti 4200 card and have had that driver package install successfuly on numerous flavors of Ubuntu over the years.
apt-get spits out the following error:
Code: The following packages have unmet dependencies: nvidia-96 : Depends: xorg-video-abi-8.0 but it is not installable Depends: xserver-xorg-core (>= 2:1.8.99.905-1ubuntu3) but it is not going to be installed
Meanwhile, a check of the currently installed xserver-xorg-core through apt-cache shows:
[Code]...
The nouveau driver does work, but I would really like full 3d acceleration like I have had in the past.
I am a newbie to linux and having a hard time installing drivers for my card (gtx 260). I'm following this guide: [URL]. So do you edit the grub.conf file in etc first and then do the yum install kmod-nvidia? I've gone through this a few times, and each time when I think I've followed the steps and reboot, I get nothing. A blinking white cursor once and then a bunch of texts saying failure to mount and sleeping forever another time.
View 2 Replies View RelatedHad mythbuntu/xbmc running for 4 months with vdpau and all the same hardware. I killed it with an update and thought it'd all be easier To build it the 2nd time -- wrong! Fresh install of mythbuntu lucid off cd, Asus p5g43t-m pro, nvidia gforce 9500 gt
What I tried so far...Different drivers with the hardware app thingee. Multiple times -- Purge nvidia, purge nouveau, blacklist list of other video stuff with extra line after, stop gnome, manual install various drivers - 195.xxxxx or Synaptic install various drivers. Tried updates, adding avenard and daily build repos. Everything in combinations. Outcome remains consistant. Lo res error start, can't load nvidia driver, selected but not in use, xorg.conf needs editing.
I'm getting the same error messages as the common nvidia help posts describe but the solutions aren't working for me.
4 days of this, 3 installs plus a shot at Mint, and no progress. I'm pretty frustrated. I'd consider returning to karmic if I didn't think the updates would pork the nvidia driver all over again.
Last install of 9.10 there was a required edit of vmalloc=256M and a shut off of cx18. That's been fixed in lucid? What else ccould it be?