I have 2 pc connected to a HP officejet j6480 1 pc connect by usb the other is eth via a router. The eth pc will not print anything but a test page. It it open a print box but won't give a option to print. The other pc is also on the same router. USB print fine.
View 1 RepliesI'm struggling on installing a KONICA-MINOLTA printer magicolor 4695MF printing properly with Linux Mint Debian Edition (up to date). The test page works fine...
KONICA-MINOLTA delivers 2 PPDs: one for standard printing and one for OpenOffice printing (available on the KONICA-MINOLTA support site).
Leaving a side the one for OpenOffice which is poor in using the capabilities of the printer, I concentrate only on the global one (M4695PX.ppd).
It's much more difficult for other applications, starting with EVINCE: some PDF files are printed properly (i.e. those generated in OpenOffice by the CUPS PDF printer), others come out as one only blank page, regardless to the original length of the document.
So documents received from 3rd party may be "printable" or not. And trust Murphy, the most critical aren't printed...
Attached, the troubleshooting file generated by [system-config-printer] => [URL] ...
I have set up a local server running 10.04. I have cups installed and running. I can access the server via 192.168.28.200:631 webapoge. I can print test pages from that site. But when I try installing the networked printer on a client, the printer will install but I can't get the test page to print.
View 1 Replies View RelatedI've installed Ubuntu 10.10 on an old box to use as an office print/fax and file server. I tried the server edition but I had no chance with command line programming so I've just used normal Ubuntu.
Ubuntu itself is working fine and I've installed my HP Officejet printer and it's fully working on the Ubuntu box. SAMBA and CUPS are installed.
I've then added the printer onto my Vista machine and here's where the fun starts. The Vista box sees the printer on Ubuntu, adds it with no problem and happily prints test pages, but I can't get it printing anything else.
I can't for the life of me find any reason why it would print a test page, but not print from Word, adobe or even a browser.
I just installed a Brothers HL2170W printer on my desktop which is running Ubuntu 1004 I had no problem with the install and it is working. The problem is when I send a page to print it takes 5 minutes before it prints. Does anyone know if this is normal or if there is a fix. I have the printer connected with a USB cable.
View 2 Replies View RelatedI've recently installed F15 LXDE RC from the livecd and connected my USB Brother All-In-One MFC-5440cn printer. After following the Brother installation page, the Cups & LPR drivers are installed but when I'm in the cups page (http://localhost:631/admin), the printer will not print a test page or print from any application. The LCD panel on the printer does show 'receiving data' but nothing comes out. The last version of Fedora I had running was F13 and the same printer worked fine.
Are there any other printer drivers I need to install besides the Brothers? The printer does show up in the Print Manager but nothing prints. I did have this same type of issue with Mageia Beta 1 and ended up installing a2ps, which wasn't included in the original print drivers, and it is now printing. So I had to install a2ps with F15 but still no print output. Something must have changed with the recent distros causing this. After looking at the output of dmesg I see this:
Code:
WARNING! power/level is deprecated; use power/control instead
[14.867397] udev-configure-printer[587]: add /devices/pci0000:00/0000:00:13.2/usb1/1-3/1-3.2/1-3.2:1.0
[14.867991] udev-configure-printer[587]: parent devpath is /devices/pci0000:00/0000:00:13.2/usb1/1-3/1-3.2
[14.869115] udev-configure-printer[587]: Device vendor/product is 04F9:016D
[14.880470] udev-configure-printer[587]: MFG:Brother MDL:MFC-5440CN SERN:- serial:BROM5F412304
[14.880520] usbcore: registered new interface driver usblp
[15.902920] udev-configure-printer[587]: failed to connect to CUPS server; giving up .....
Any idea why it's failing to connect to Cups or any idea how to find out? Is it possible to have too many USB devices connected? I'm using a 4 port usb hub in use and also using a usb mouse/keyboard connected.
I have a couple of large-format printers (Epson R2400, HP 9650) which I only use infrequently. If they are not used very often, they dry out, the print heads get packed up, it's an expensive mess to deal with when times comes to run off some prints. The printers are physically connected to a Windows machine to which my Ubuntu computer is networked.It would be helpful if there was a utility that could initiate a test page print job on the machines, which could be scheduled to run once a week or so. I've had no luck finding such a thing for Windows
View 9 Replies View RelatedI have a FC11 box, with an HP prineter attached. I trying to print from my laptops after I have setup samba and shared the printer , It was working fine when I was installing FC4 and FC5. I am not sure what is missing. when I tried to print from the XP box I got "Test pge failed to print" error.
View 9 Replies View RelatedI have a problem printing to my HP printer.
What is my problem? I have a page (one page - text an graphic) to print. When I sent it to my printer it prints OK. When I sent it agian, the output is totally garbled. When I sent it again (a third time) it is OK. Sent it again (4th time) it is garbled. Sent it again ... you get the picture ;-). Alternating good and bad pages.
What is my setup? I run Fedora 14 with Cups 1.4.6. The printer is a HP Deskjet 940C. It is connected to a linksys wireless print server. It is configured in CUPS to use ipp printing. The driver I use in Cups is 'CUPS+Gutenprint v5.2.6 Simplified (color, 2-sided printing)'.
I just installed openSUSE 11.4 on my 2 home machines. My home network lies behind a nat router but I still use the external zone setting for my firewalls. In the past to enable network printing between the two computers I opened TCP and UDP port 631. Yast would then see the remote printer, set it up and all was good. This time Yast sees and sets up the remote printer as usual. When I print the test page nothing happens. Checking the cups admin page at localhost:631 on the host machine shows the printer is set up to share but nothing is in the print que. Printing works just fine on the host computer.
View 2 Replies View RelatedAfter some effort, finaly managed to get my Canon PIXMAiP4200 printer connected as a network printer. (I connect it through the USB printer port on a DLink DI-524UP router) Everything seems ok so far, except that I cannot find any means of specifying that printing should start from the last page.
View 2 Replies View RelatedI'm using Opera on openSUSE 11.2, and whenever I test java (using this page), it says "Applet crashed." Is there something special I need to do to get java to work properly?
View 1 Replies View RelatedI am trying to set uamsung clx2160N as a standalone network printer on my home network. It is a printer with standalone network capability and is connected directly to my router and has a static IP number. We have a few Windows computers at home and they had no problem detecting the printer, installing the drivers and working. Unfortunately my Ubuntu computer recognises the printer and I can even access it's setup and diagnositcs through its IP number. However when I try to add it as a printer, drivers for it cannot be located. #ve tried setting it up three ways:1. Using Samsung's own setup package - finds printer and all the details it needs to work but offers no drivers2. Using Ubuntu's printer setup - recognises printer but stalls at Searching for Drivers dialog3. Trying to *** printer using CUPS - no problem finding and recognising printer, but when I come to search for the driver I get Internal Server Error.
I have of course been trying to do all of these as root. That's the limit of my knowledge reached and searches on the net aren't helping me either. The printer works fine directly connected via USB, so the drivers are on the computer somewhere. How do I get them set up to use the printer on the network?
I have a parallel port printer connected using usb->parallel adapter. Sometimes the printer prints sometimes it doesn't.
A job will go the print queue and then sit there for ages. Sometimes if I unplug and then replug the usb->parallel cable the printer will print other times it will print half the document then freeze until the cable was unplugged and replugged again.
The printer never shows up in the list using lsusb (only my usb mouse and scanner do).
The printer is an hp deskjet 690c and worked fine under WinXP through a normal parallel cable. The one thing I haven't tested (but will test tomorrow) is the usb->parallel cable in XP.
I successfully added/shared a network printer in SUSE 11.3 32 bit, but when I try on the 64 Bit box it didn't work out very well.What ports need to be open ? Is it necessary to open port 631 in YAST->Firewall->Advance- >UDP and IPP ?(TCP 631 already open) What services need to be running? Here is the error log :
[16/Dec/2010:19:25:43 -0500] [cups-polld xxx.xxx.xxx.xxx:631] CUPS-Get-Printers failed: Forbidden
XXX is my server IP
I have two different ways to print to my HPOfficejet Pro 8500. They look like two different printers to the software.
When I attempt to print a PDF file one of these prints a mirror image; the other cuts approximately 1/2 inch from the top of the page.
OpenOffice.org files appear to print without problems.
I have openSUSE 11.2 and HPLIP 3.9.8
I have my Epson C46 working on my Ubuntu 9.10 machine, my XP machines are showing the printer as ready and will send a test page to the Ubuntu printer but it doesn't arrive at Ubuntu - doesn't show in the print job list on Ubuntu but does in XP??
File sharing is now working in both directions.
I have an HP J4680 all in one that, for some reason, does not process the print job immediately when I send it. When I open my printer's properties it will list the printer's state as idle and when I go into the print que it tells me the job is scheduled for . . . (some time) which is, I think, about 5 min later by the clock on the task bar. I've been all over the settings and don't see anything that looks like it applies to that. Usually I've been restarting the printer and computer and then it will print when I send the job. Tonight I waited until the time and it did print according to the scheduled time. I need to find a way to always have it print right when I send the job.
View 2 Replies View RelatedWe have an HP F4135 printer which has worked fine for at least 2 years, now, but it has started acting up since installing Ubuntu on our computers.
We had been running Windows XP on the computer to which the printer was connected, but ever since we "upgraded" to Ubuntu the printer has been printing green in place of black whenever using it to print any sort of document from Firefox. This isn't black mixed with green; it's a bright, lime green.
For some reason, it works fine when it's printing something directly from the computer's hard drive, like a document, .pdf file, etc. It's only when printing from Firefox that it starts messing up, whether it be a file opened temporarily from a website or the direct contents of a web page.
We've tried adjusting the printer settings and the only thing that makes a difference is changing the Printout Mode from Normal (Color Cartridge) to Normal Grayscale (Black Cartridge). This seems to be the only thing to stop it from printing in green, but that really isn't a good fix, since it makes all the other colors turn to black, which isn't really fixing the problem.
I'm running a standard 13.1 32 bit install with an HP deskjet 990C, run off of USB. Until today everything has printed properly. Now nothing prints. Nothing has been installed unless it came through slackpkg, and yes it is still on the correct setting for arch and revision. CUPS shows printer as installed, accepting jobs an idle. No error messages are appearing but nothing is reaching the printer. The info I can glean is from the error logs in CUPS:
[Code]....
All seems well in Ubuntu printer setup and drivers. Cups, hpijs hplip etc., system finds printer and sets it up and from system/administration/printing the printer shows up with the right description Hp deskjet d2600 on local host. when I try to print I get message "started job" and another message "finished job" but nothing prints. The log Var/log/cups/error_log shows only one thing that I think is wrong "cupsd authorize:no authentication data provided". my user name john and one other Andy (I installed) show up in lp group. I could attach the whole error_log file if it would help. I am new to Linux but love it. I used Windows NT for years. I am the administrator on the box. Don't know what to try next.
View 11 Replies View RelatedI have successfully gotten my Canon MX300 Printer to work with CUPS. The printer works great, but for some reason it prints out white lines incredibly slow. The printer acts as if it is printing out actual text, e.g. if I have half a page of empty space, it prints it line by line for some reason... Anyone know what may cause this? I know that CUPS is not ideal with all printers, but it did not do this at first actually.
View 2 Replies View RelatedJust recently got a few printers connected to the network at my shop and I've managed to get them connected in with samba for the linux clients. Whenever I try to print from one of the clients, the printer will click on and whiz away, but only prints on the first page stuff that looks like this:
Code:
%!PS-Adobe-3.0
%%BoundingBox: 38 24 574 768
%%Title: Enscript Outpu
%%For: User N
It seems to me that the printer isn't processing the postscript data properly (or I'm just not sending it in the right format) but I'm at a loss as to how to go about fixing it.
I would like to create a dedicated Samba print server. I have two printers on my LAN, one printer came with its own NIC and the other is on a Win server box. I would like to setup Samba so that I can just access that server (Samba printer server) and both network printers will show up on there for me to connect to. On that note, can I also load the drivers on my Samba server? Drivers for different Windows flavours and also Mac OSX drivers.
View 1 Replies View RelatedI have an HP Printer which prints black horizontal lines after each line or colors an entire blank line black, so a blank page will come out all black. Others who have access to the Printer are able to print well, without any problem.
View 1 Replies View RelatedI've encountered some problem in setting my printer HP D1560; the printer pulls in paper but prints no image. how to set it running under WinXP?
View 5 Replies View RelatedI'm using Ubuntu 10.04, and I have an HP D1660 printer. The printer has already been added, and HPLIP is installed. I can't get anything to actually come out of the printer, even though I can send a job to the printer. Does this have anything to do with CUPS?
Here are some of the last error log messages after using the printer troubleshooter (I only included some because it's a long list):
I have two Linux machines both running Debian (I do not want Windows to be involved at all). One is a desktop and one is a laptop. I desire to connect a not-yet-purchased printer/scanner combination machine only to the internal LAN via my router (Linksys WRT54G) via Ethernet cable, or via wireless if the printer/scanner has that capability. I want to be able to print to that printer (and scan from its scanner) by only having to turn on the printer/scanner and only one of the other computers, and not have to have both Linux machines turned on in order to print and/or scan.
So my questions are:
When I look at specific models of printers, what should I be looking for in their specifications that indicates that this configuration is possible (i.e., should I be looking exclusively for printers that say they are "wireless printers" or "network printers")?The reason I ask this question: In my online searching, I thought "networked printer" or "stand-alone network printer" meant just that, but what I found instead are pages and pages of instructions on how to connect the printer locally to a Linux machine, with the associated setup to allow that Linux machine to serve print requests coming from other machines on the LAN. And that approach is not what I want to do (with the notable exception of temporary setup to validate that the printer is responding to requests for printing and scanning from Linux).
Are there particular brands, makes, or models that I would have better luck in getting to work in this manner (i.e., "better stick with HP or Xerox")? Am I kidding myself that a combination printer/scanner would work in the same fashion and still be relatively easy to set up on both Linux machines without resorting to some Windows-centric approach? Result of my searching so far (I have not worked my way through all of these in detail, but plan to): References to local printer connection which is not what I want:
Setting_Up_a_Network_Printer_using_CUPS
Set up a network printer using cups
Set up a printer
The post inside Setting_Up_a_Network_Printer_using_CUPS that starts with "running an HP Photosmart 8450 as a stand-alone networked printer" (where is the permalink?) is as close as I could get, but I am concerned that the instructions given are specific to the HP Photosmart 8450, or specific to the HP vendor, versus for all printers that can be connected to an Ethernet network (not that being locked into HP is going to be a problem necessarily, but I would like to know why if that is the case). Linux compatible printers says "Have a look at LinuxPrinting for known working drivers for printers data base. Also buy from a linux friendly company, ie HP, Brother, Epsom." Later in that thread, someone said Definitely don't buy canon.
I do not have the hardware to do this yet. I simply want advice on what route to take before I make the investment. If I had the money I would simply invest in a wireless combo setup, but I unfortunately do not. I do however have an idea. I am currently stuck with a standalone system that is running XP strictly for the use of magicjack. I was thinking I could hook up this combo machine to that computer and network it in via that. However, would the scanning capability only reside in the hardwired computer or could I do a network scan somehow?
View 2 Replies View RelatedI want to setup my Epson Stylus (515W)-A letter before the 5 but not sure what. Basically when I open CUPS I click on add on new printer, I enter add printer but then the page says access denied. Also this is a network printer.
View 2 Replies View Related