Ubuntu Networking :: Vista Prints Test Page But Nothing Else?
Oct 18, 2010
I've installed Ubuntu 10.10 on an old box to use as an office print/fax and file server. I tried the server edition but I had no chance with command line programming so I've just used normal Ubuntu.
Ubuntu itself is working fine and I've installed my HP Officejet printer and it's fully working on the Ubuntu box. SAMBA and CUPS are installed.
I've then added the printer onto my Vista machine and here's where the fun starts. The Vista box sees the printer on Ubuntu, adds it with no problem and happily prints test pages, but I can't get it printing anything else.
I can't for the life of me find any reason why it would print a test page, but not print from Word, adobe or even a browser.
I'm struggling on installing a KONICA-MINOLTA printer magicolor 4695MF printing properly with Linux Mint Debian Edition (up to date). The test page works fine...
KONICA-MINOLTA delivers 2 PPDs: one for standard printing and one for OpenOffice printing (available on the KONICA-MINOLTA support site).
Leaving a side the one for OpenOffice which is poor in using the capabilities of the printer, I concentrate only on the global one (M4695PX.ppd).
It's much more difficult for other applications, starting with EVINCE: some PDF files are printed properly (i.e. those generated in OpenOffice by the CUPS PDF printer), others come out as one only blank page, regardless to the original length of the document.
So documents received from 3rd party may be "printable" or not. And trust Murphy, the most critical aren't printed...
Attached, the troubleshooting file generated by [system-config-printer] => [URL] ...
I have 2 pc connected to a HP officejet j6480 1 pc connect by usb the other is eth via a router. The eth pc will not print anything but a test page. It it open a print box but won't give a option to print. The other pc is also on the same router. USB print fine.
What is my problem? I have a page (one page - text an graphic) to print. When I sent it to my printer it prints OK. When I sent it agian, the output is totally garbled. When I sent it again (a third time) it is OK. Sent it again (4th time) it is garbled. Sent it again ... you get the picture ;-). Alternating good and bad pages.
What is my setup? I run Fedora 14 with Cups 1.4.6. The printer is a HP Deskjet 940C. It is connected to a linksys wireless print server. It is configured in CUPS to use ipp printing. The driver I use in Cups is 'CUPS+Gutenprint v5.2.6 Simplified (color, 2-sided printing)'.
i'm setting up apache on 5.3. i can access the apache test page without a problem from the server via URL... But i can't figure out how to access this page from another computer within the domain (for when i upload my home page.
I just installed a Brothers HL2170W printer on my desktop which is running Ubuntu 1004 I had no problem with the install and it is working. The problem is when I send a page to print it takes 5 minutes before it prints. Does anyone know if this is normal or if there is a fix. I have the printer connected with a USB cable.
I know my driver works and that cups is up and running, because I can print off test pages to my heart's content, but I can't get any actual documents printed. I'm connected over the network at work to a Japanese NEC MultiWriter 3650n (it seems to be Japanese-only---I could find on drivers was in Japanese). It shows up in System=>Administration=>Printing. I set it as the default printer, and, as I said, it prints off test pages without a hitch. But whenever I open, say, a PDF and try to print it, the document appears to get sent, but never actually prints, and never shows up in the print queue (while the completed test pages do).
I installed my epson stylus tx420w through cups web interface. I used the PPD file provided by the driver recommended in linuxprinting.org.But when I try to print the test page (or anything else), nothing is printed. According to the diagnostics, the printer status is "Processing page 1...", but it won't go beyond that.I've already tested it, it's fine. But won't work in ubuntu. Don't know what's going on.
I am trying to set up a web page for the business and we have had the website or domain for a while but no one has put anything on it. I have never done anything like this before so i typed in the website and got the apache test page saying that i should add this: /var/www/html/
1) i'm not really sure what to add it to 2) i've tried adding it to the website url and that comes up with invalid page 3) could someone please explain in simple terms how i can get on to the webpage so i can start adding content to it?
I have set up a local server running 10.04. I have cups installed and running. I can access the server via 192.168.28.200:631 webapoge. I can print test pages from that site. But when I try installing the networked printer on a client, the printer will install but I can't get the test page to print.
I had installed and checked lamp stack last night but today when I type http://localhost the fodora test page for apache didn't come up. It is just blank. I had also configured apache to load after every boot.
I just installed openSUSE 11.4 on my 2 home machines. My home network lies behind a nat router but I still use the external zone setting for my firewalls. In the past to enable network printing between the two computers I opened TCP and UDP port 631. Yast would then see the remote printer, set it up and all was good. This time Yast sees and sets up the remote printer as usual. When I print the test page nothing happens. Checking the cups admin page at localhost:631 on the host machine shows the printer is set up to share but nothing is in the print que. Printing works just fine on the host computer.
I recently built a server from an old box using Ubuntu Server 9.10. This is my first server and I am very new to the server world.I have an Epson Stylus NX400 connected via USB. I have managed to configure it to the point where I can see the printer listed on my client laptop and can print a test page. However, I cannot print anything else. When I access the job history through the CUPS adminI can see that the print jobs were recognized and marked as complete, even though the printer never physically engaged.
Can't access localhost test page, but opens localhost page when I use full dns, at least from local network machines?
Running slackware13.1, Httpd2.2.15, 2wire gateway. Firewall web&http pinholes for ports 80,443. Port 80 is working.
Code:
Returns error:
Quote:
Code:
Code:
Added 4400host.net to Resolve DNS on 2Wire Gateway(Never had to do this before to access httpd test from same machine or network machine?
Changed HTTPD.conf
Code:
Code:
Quote:
"It Works!"
Never encountered this before, usually httpd test worked for "localhost" with minimal effort. I am concerned to procceed with this odd behavior. Has anyone else encountered this configuration is?
I have a couple of large-format printers (Epson R2400, HP 9650) which I only use infrequently. If they are not used very often, they dry out, the print heads get packed up, it's an expensive mess to deal with when times comes to run off some prints. The printers are physically connected to a Windows machine to which my Ubuntu computer is networked.It would be helpful if there was a utility that could initiate a test page print job on the machines, which could be scheduled to run once a week or so. I've had no luck finding such a thing for Windows
I've recently installed F15 LXDE RC from the livecd and connected my USB Brother All-In-One MFC-5440cn printer. After following the Brother installation page, the Cups & LPR drivers are installed but when I'm in the cups page (http://localhost:631/admin), the printer will not print a test page or print from any application. The LCD panel on the printer does show 'receiving data' but nothing comes out. The last version of Fedora I had running was F13 and the same printer worked fine.
Are there any other printer drivers I need to install besides the Brothers? The printer does show up in the Print Manager but nothing prints. I did have this same type of issue with Mageia Beta 1 and ended up installing a2ps, which wasn't included in the original print drivers, and it is now printing. So I had to install a2ps with F15 but still no print output. Something must have changed with the recent distros causing this. After looking at the output of dmesg I see this:
Code: WARNING! power/level is deprecated; use power/control instead [14.867397] udev-configure-printer[587]: add /devices/pci0000:00/0000:00:13.2/usb1/1-3/1-3.2/1-3.2:1.0 [14.867991] udev-configure-printer[587]: parent devpath is /devices/pci0000:00/0000:00:13.2/usb1/1-3/1-3.2 [14.869115] udev-configure-printer[587]: Device vendor/product is 04F9:016D [14.880470] udev-configure-printer[587]: MFG:Brother MDL:MFC-5440CN SERN:- serial:BROM5F412304 [14.880520] usbcore: registered new interface driver usblp [15.902920] udev-configure-printer[587]: failed to connect to CUPS server; giving up .....
Any idea why it's failing to connect to Cups or any idea how to find out? Is it possible to have too many USB devices connected? I'm using a 4 port usb hub in use and also using a usb mouse/keyboard connected.
I use .htaccess to deny all ip addresses except certain to an internal wiki on a subdomain.
Code:
If access is denied to the homepage users are shown the Fedora test page instead of my own custom 403 error page. When I go to a page - not home - I see a standard 403 error page.
Code:
Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request. Apache/2.0.54 (Fedora) Server at wiki.domain.com Port 80. What am I missing here? Seems like my ErrorDocument is not being reached..
I'm using Opera on openSUSE 11.2, and whenever I test java (using this page), it says "Applet crashed." Is there something special I need to do to get java to work properly?
I have been given an old Canon BJC-4310SP printer. Performing the "built-in" test print works perfectly. Using the standard CUPS installation procedure (in Debian Lenny) also worked without a hitch. The new printer was correctly identified, CUPS suggested the appropriate driver and then installed and configured the printer as directed. But asking CUPS to print its test page crashed with the following message: "Unable to open parallel port device file: Permission denied".
I have a FC11 box, with an HP prineter attached. I trying to print from my laptops after I have setup samba and shared the printer , It was working fine when I was installing FC4 and FC5. I am not sure what is missing. when I tried to print from the XP box I got "Test pge failed to print" error.
I'm using fedora 14. And I have installed apache, PHP and MySQL. I tried testing PHP with phpinfo(). But when I view it view my browser (localhost/test.php) it just shows the code itself instead of displaying the phpinfo page. This is the content of my test.php page.
i opened up my browser to surf the web and a page popped up i had never seen before.Apache 2 Test page powered by centos. Any address i put into my firefox browser won't come up and i'm stuck on this test page and,i can't locate it on my computer to remove it.How do i get rid of it and more importantly how did it get on my computer in the first place?
I am trying to install mysql 5.1.44..so i downloaded the binary package, i extracted it and then followed the instructions that were in the manual but i keep getting this error when running this command
Installing MySQL system tables... 100315 20:07:27 [Warning] Can't create test file /var/lib/mysql/mosty.lower-test 100315 20:07:27 [Warning] Can't create test file /var/lib/mysql/mosty.lower-test
After a reinstall of 10.10, I am able to turn on file sharing and so I set up a shared folder.
Windows Vista can see this folder but in my network place, there is only one icon, and it's a "Windows Network" icon. Upon clicking on that, I can see the local network, "Rompus Room".
When I click on Rompus Room, nothing happens for a while, then I get a message saying, "Opening "ROMPUS ROOM". Then I get the final message, "Unable to mount location", followed by, "Failed to retieve share list from server"
I have created mobility of 20 nodes and vbr traffic using following attached script I executed the file as ns234 vbr.tcl I got the vbr.tr and vbr.nam but I was unable to load the graph using matlab <trgraph> I thought problem with is vbr.tcl script.
i am able to try ubuntu and everything works fine until i try to install. the menu comes up to the first page where it tells you to plug in your machine and make sure there is enough disk space and network connectivity. when i hit next on this page the mouse icon changes but the next page never loads. the longest i let it hang there was 2 hours. ive tried multiple times with the same result.
im running from a flash drive on an ASUS Eee PC 1001P-PU17
