I have installed CentOS in multi-boot set up.when i am trying internet thru win7,its working fine but when i am tryin to connect using CentOs,its not working.I have tried and changed the mac address to the one that is on windows(this worked fine with ubuntu) but the issue remains in CentOS.
View 8 RepliesI finally managed to install pppoe and pppoeconf. When I type command 'pppoeconf' , it invokes some window and I put username, passwd etc. But my net connection won't start. I have posting the output of various commands related to networking.ifconfig
Code:
eth0 Link encap:Ethernet HWaddr 00:0f:b0:4a:54:a7
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20f:b0ff:fe4a:54a7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1388 errors:0 dropped:0 overruns:0 frame:0
[Code]...
I have installed fedora 14 minimum install and I have configured my machine for Static IP but now i cant reach any external sites or repository, in fact all i can do is ssh to the box. below is the configuration in my /etc/sysconfig/network-scripts/ifcfg-eth0 file:
DEVICE="eth0"
BOOTPROTO="static"
BROADCAST="10.27.18.255"
IPADDR="10.27.18.117"
NETMASK="255.255.255.0"
[Code]....
and my DNS is setup to point to my ISP's primary and secondary DNS servers. I have brought the interface down then up after each change but still cannot ping anything.
I installed RHEL 5 today and set my network. Did it as follows:Eth0 connectionPrimary DNS 192.168.1.1When I click on Activate, it says:8139too device eth0 does not seem to be present, delaying initialization.This message shows no matter how many times I log out or restart.I don't know what the heck is the problem. I've done the essentials but still it's not working. I looked up on the net but people were saying things like ifconfig and lspci, and at the end still weren't able to solve it. I don't know all this since I'm new to Linux. Another important thing...after facing this same problem some time ago, I installed Centos which asked for internet settings right at the time of installation. And after logging in for the first time, I was able to use internet without any problem. How come internet works on Centos (which is a copy of RHEL) without any problems, but not working on RHEL itself?
View 14 Replies View RelatedI was able to connect to internet using PPPoE until I configured Samba network and set the machine as its server; does this two related? Is it possible there's a conflicting configuration, say DNS server config for example?
View 2 Replies View RelatedI installed the Centos 5.5 on a WM instance. Run out of space after doing the updates. It is very difficult to keep re-partitioning /
I tried to install a new instance but it doesn't let me configure the disc and it just goes and install the OS.
How can I use the good old installation options etc?
What happened to control? This became a control nightmare.
full steps of configuring mail server in CentOS 5.5.
View 4 Replies View RelatedI have ubuntu 9,10 and 7 repositorie disks I bought from osdisc.I installed ubuntu next to widows xp 3.I can't seem to connect to the internet or configure my system to do so.My us robotics usb 2.0 modem works great in xp but not at all in ubuntu.Is there someone out there willing to help me step by step?Or in anyway possible.Directions on how to or where to go for help.I'd really like to not be dependent on Microsoft completely. My telephone number is 903-566-3590. My fax is 9035660030. My address is 12862 Sandy Point Drive Tyler, TX 75707
View 1 Replies View RelatedI recently bought a dell inspiron 14 n4010 and i've installed windows and Ubuntu 10.04 in it. The problem is that i'm not able to access internet in my ubuntu. I'm using asianet broadband connection and i'm able to get internet in my desktop when i connect the cable to the system. But when i did the same with ubuntu 10.04 in my laptop, i'm not able to get internet access. I'm able to access internet in windows though. But i hate using windows.
View 9 Replies View RelatedI am using ubantu 10 and broadband where userid and passwd has been configured in router box. So when I connect this from windows its automatically connected (using ppp0e and dhcp), whereas in linux it could not connect.
View 2 Replies View Relatedis there a possibility to connect to my router admin zone from internet using wan ip? from lan I can do that using 192.168.x.x IP but when Im in work and something go wrong at home how can I check configuration of my router from outer world instead of lan?
View 7 Replies View RelatedI just installed a command line version of karmic to an old desktop. During installation, DHCP failed, so I attempted to configure manually (without really knowing what I'm doing) and wound up without a connection. I've been searching for solutions, but really don't understand what I need to do. A million thanks to anyone who can help me get up and running (or at least give me a push in the right direction).I can either connect the computer directly to the cable modem via USB, or directly to my wireless router via ethernet cable. I know what the ip address for my laptop (which is connected wirelessly to the router) but don't know if that would be the same for the desktop or not, and don't really know anything else.
View 3 Replies View RelatedI have latest ubuntu and I have made 3 vm's for them.
VM 1: with 2 NIC cards, one is NAT connected directly through my host machine to the internet with ip address 192.168.190.142. Second NIC card is "host only" with ip address 192.168.0.10
VM 2: with 1 NIC card, "host only" and ip address 192.168.0.100
I want VM 2 to connect to the internet but through VM 1. for this I used following configuration in
Code:
/etc/network/interfaces,but it is not working[code]....
I have given my VM 2 the gateway of VM 1 but it is not going through.P.S: both machines are pinging each other properly.
I have latest ubuntu and I have made 3 vm's for them.
VM 1: with 2 NIC cards, one is NAT connected directly through my host machine to the internet with ip address 192.168.190.142. Second NIC card is "host only" with ip address 192.168.0.10
VM 2: with 1 NIC card, "host only" and ip address 192.168.0.100
I want VM 2 to connect to the internet but through VM 1. for this I used following configuration in
Code:
/etc/network/interfaces
but it is not working
Code:
auto lo
iface lo inet loopback
auto eth1
code....
I have given my VM 2 the gateway of VM 1 but it is not going through.
P.S:
both machines are pinging each other properly.
In windows, when I use an HSPDA modem, internet traffic will be automatically directed through it. Everything will go back to normal once broadband connection is disconnected. In fedora 12 this is not the case, internet traffic will still go through the lan interface. Is there a way to mimic windows behavior in linux?
View 3 Replies View RelatedI configure my server just like on the link found in novell i hope some can help me here. my client is able to recieve DHCP address and everything is working fine on the network how ever my client cannot pullup any website, but my server is able to pullup whats wrong on this one.
Cool Solutions: HOW-TO: Set Up a SUSE 10 Machine As a Router
I have to servers online, both are connected to a virtual rack and both have public inet IPs. The thing is that I want the communication between the servers to be handled locally. This is my ifconfig from one of my servers,
eth0 Link encap:Ethernet HWaddr x:x:x:x:x:x
inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.248
inet6 addr: fe80::21d:9ff:fef1:e665/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:114342 errors:0 dropped:0 overruns:0 frame:0
[Code]...
Are there detailed instructions for Suse 11.2, anywhere, on installing a hardware dial-up modem and configuring it to get an Internet connection?
View 2 Replies View RelatedI installed syslog-ng-3.0.3-1.rhel5.i386.rpm and at first blush it appears to be working fine to /var/log/messages. However it doesn't seem to be doing any other ancillary logging as defined in syslog-ng.conf (I've had to mod /etc/init.d/syslog-ng to look in /etc). e.g.
destination d_auth { file("/var/log/secure"); };
filter f_filter3 { facility(authpriv); };
log { source(s_sys); filter(f_filter3); destination(d_auth); };
I'm using a syslog-ng.conf which has served me well in the past (v1.6.9 on fedora).
where i can learn configuring DNS and apache
View 1 Replies View RelatedRecently my motherboard went out, I replaced it and booted centos 5. All went well except sound, video tuners and netoworking. The sound I re-configured, and have gotten tuners working but I am running into trouble with the new network card. The networking setup is;
DSL wireless router/modem IP 192.168.0.1 connected to XP computer through WIFI IP 192.168.0.3. all set to subnetmask 255.255.255.0 and with DNS servers 192.168.0.1 and 205.171.3.25 the XP computer is the only one that supports my wifi card. On wired LAN I share that connection to 4 devices. 3/4 work well, my cent os 5 box will not connect. here are the lan settings:
win xp: IP 192.168.0.60 255.255.255.0
mac 8.6: IP 192.168.0.34 255.255.255.0
blueray: IP 192.168.0.65 255.255.255.0
[code]....
Am using Icefaces1.7.2 in tomcat5.5.23 in Centos5( jdk 1.6.06 and jre 6u11 and no X window system in my server ).. Am getting the error(java.lang.Error: Probable fatal error: No fonts found) when am using the functions getFontMetrics() and drawString() methods in my Captcha Image Generation programs. I am only using the fonts that me retrieved using ge.getAllFonts() ( i.e., the fonts available in the system ).
View 6 Replies View RelatedI've got a server with several different virtual hosts on them, e.g. host1.com, host2.com, host3.com.
Is there a way I can set up an email alias just for an individual domain?
e.g. I want to set up help@host2.com, but not to have help@host1.com or help@host3.com.
I can't see how to do this in the /etc/aliases file...
i've got a select based application that wants to support a large number of mostly idle connections. the code is java and works on windows, suse enterprise linux, mac os x. it does not work on centos 5.5 (32-bit, 2.6.18 kernel, 1G of memory).
i've read and followed the directions in various articles about tuning linux for large numbers of connections (including the C10K problem), and gotten the number of sockets up to 3200.
these didn't make any apparent difference:
[URL]
on windows, i can get up to around 78,000.
on suse enterprise linux (a few years ago), i got up to 90,000. that's where i got bored and stopped.
on my mac laptop with os x (snow leopard), i got up to 10,500.
i have used ulimit -n 10240
my current goal is 10k sockets.
the test is that i'm opening one socket at a time until it fails. when it fails, many of the sockets which have already been opened also fail, in one giant cascade. sounds like a buffer / memory problem.
each group of 64 sockets gets a thread to manage select calls for them. thus i'm only using around 61 threads total when it fails.
configuring DHCP server with two NICs. I need DHCP server with 2 NICs:
eth1 - 192.168.103.11
eth2 - 192.168.123.11
The client also has two NICs and suppose to receive ip addresses eth1 from 192.168.103.0 and eth2 from 192.168.123.0 Here is the dhcpd.conf from dhcp server:
ddns-update-style interim;
authoritative;
ignore client-updates;
[code]....
I've installed CentOS 5.6 to my laptop, primarily to use some simulation programs. With much help of google I'm getting my hardware and software to work quite well, but I still have some troubles.My first problem is my Synaptics-Touchpad. It is extremely sensitive and I am not able to scroll. Is there any application which allows me to configure it properly? Before CentOS, I've tried openSUSE 11.4, where there was an application especially for configuring synaptics touchpad (dont't remember the name though). In general, the "feeling" of the touchpad was way much better under openSUSE, but I can't define that properly. I have a bluetooth mouse (Dicota Blue Light) conntected to my laptop, which is working fine except for the scroll wheel, which doesn't work at all. How can I activate it?
View 3 Replies View RelatedI have installed CentOS on my system.When I am trying to activate internet,its not working.I tried to change the mac address to what i use for win7 but CentOS is not accepting that address.It throws error like:"unexcepted mac address".same address works fine with win7 and ubuntu.I am using cable modem for a standalone pc.
View 4 Replies View RelatedI am using Centos 5.4 on an Intel DG451D Main Board. Two SATA drives in RAID1 mode via the main board's built in AHCI controller. It seems to work just fine but I would like to be able to monitor the state of my drives and controller, especially during a re-build and make configuration changes etc if possible, so new drives can be added etc from within the OS. Is there a way to do this within Centos or am I stuck with using just the BIOS configuration system? Apologies if this is a stupid question - I am pretty new to this and have spent several hours trying to find a solution to my question but to no avail.
View 1 Replies View RelatedI've search for info on configuring ndiswrapper for the BCM4318 Wireless card. All I've been able to find is information on Ubuntu and Debian, which don't seem to use the same methods for configuration. Has anyone configured ndiswrapper for this or any wireless card on CentOS 5? I've installed 5.4.
View 7 Replies View Relatedi have linux server application based on centos 5 that run httpd daemon from /usr/local/pf/conf/httpd.conf which is generated from the /usr/local/pf/conf/templates/httpd.conf.apache22 file
the problem is every time i run my linux server application i am not able to access phpmyadmin unless i stop my linux server application which is stop it httpd daemon then start "service httpd start"
i have been told by forum moderator to create an alias for my phpmyadmin in Virtual Host but it stil dont work, i am not able access my phpmyadmin site
this is what i have done to solve this problem
- open /usr/local/pf/conf/templates/httpd.conf.apache22 file then look for <VirtualHost *:%%admin_port%%>
- add Alias /phpmyadmin "/usr/share/phpmyadmin" (Failed)
- add Alias /phpmyadmin /usr/share/phpmyadmin (Failed)
- add Alias /phpmyadmin "/usr/share/phpmyadmin/" (Failed)
[Code]....
NB : my phpmyadmin is install on /usr/share/phpmyadmin with /etc/httpd/conf.d/phpmyadmin.conf as phpmyadmin configuration file
why i still cant open my phpmyadmin site ? or why i cant run phpmyadmin together with my linux server application because it use the same daemon (httpd daemon)