I was able to connect to internet using PPPoE until I configured Samba network and set the machine as its server; does this two related? Is it possible there's a conflicting configuration, say DNS server config for example?
View 2 RepliesI finally managed to install pppoe and pppoeconf. When I type command 'pppoeconf' , it invokes some window and I put username, passwd etc. But my net connection won't start. I have posting the output of various commands related to networking.ifconfig
Code:
eth0 Link encap:Ethernet HWaddr 00:0f:b0:4a:54:a7
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20f:b0ff:fe4a:54a7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1388 errors:0 dropped:0 overruns:0 frame:0
[Code]...
I have a linux box (fedora) with two ethernet cards eth1 and eth2. On eth1 I successfully configured a PPPOE internet connection. Such that from the server I can browse the internet. On eth2 I wired it to a wireless router essentially to provide the wireless cloud. On eth2 I also configured dhcp, such that the Linux box is both PPPOE and DHCP server.However my clients on the LAN cannot access the Internet.
On passing the routing command I get
Destination Gateway Iface
196.44.x.y 0.0.0.0 ppp0
192.168.1.0 0.0.0.0 eth2 (my subnet)
0.0.0.0 0.0.0.0 ppp0.
The router (functioning as a wireless access point mainly) has a fixed IP address of 192.168.1.2 and eth2 has IP address 192.168.1.1. The dhcp file running on Linux has been set with option router (Gateway) 192.168.1.1. I cannot figure out how to correctly set the routing table such that my clients on wireless can access the internet cloud. I googled and googled but no solid solution. Any suggestions?
I have problem to access the Internet, with Ubuntu 10.04. In Windows I access the Internet in this way: Create a PPPoE Connection (with username and password), after this connect to a Wireless Network called WebSTAR (I have Wireless modem in my family PC), and connect to PPPoE Connection. After these steps the Internet works fine. .But I have same problems with Ubuntu. First I see the Network named "WebSTAR" but I can`t connect to it. And I try many times to join the Internet with "sudo pppoeconf" command in Terminal, but didn't work.
View 2 Replies View RelatedI need to implement at my sister this kind of connection: She is connected on Local area network that has about 50-80 pc's, but for internet access she must start an pppoe connection. For now when she wants to use lan she must put her local address (ps: they dont have dhcp), for pppoe she uses dhcp. Problem is that on that way she can't access lan and internet at the same time. She must disconnect from lan and then start pppoe connection and vice versa. I'm intrested if it is possible to have lan access at the same time as internet access. some kind of tunel through lan up to isp. I was googling little and so PPPoE tunneling. Is it that what I need here?
View 9 Replies View RelatedI'm having problems in accessing a storage device (NAS 200 Linksys) in a network via Ubuntu. I think the problem is with the configuration of Samba.
On my computer the login and password are the same in Ubuntu (9.04), samba and Win XP.
Under windows I view the device in the network and, when I click on its icon, a window opens with the directories that have access.
Under Ubuntu, I can see all the computers in my workgroup and the device. However when I click on its icon only a blank window is opened.
I share printers without problems.
In my settings for the samba security = user.
Does anyone know if there is any configuration that allows access to the NAS?
I have a server at home running as a file server and DHCP connected to a switch with a wireless AP in there as-well. with this setup I can access the files and do some configurations via SSH on the actual server anytime I'm able to get the wireless signal, now lately I felt the need to be able to do the same but this time over the internet. I've read somewhere already that I'm gonna need a router with port forwarding and NAT, then know the IP address of the server but my problem is once you start talking about routers then you need broadband connection which is something I don't have. Getting a router is not much of a problem but without ADSL like connection I guess its useless, what do I need to do?
View 7 Replies View RelatedI have trouble connecting to internet when connecting using pppoe-start, even though it says it's connected and the pppoe interface is there. I test the connection by sending a ping to a known IP address and got "destination unreachable".
View 2 Replies View RelatedI need a linux distro who provides the following:1) Has an partitioner who can resize fat , ntfs ,ext* , .....filesystems.2) Has an excellent hardware support3) The installer can install console or graphic mode 4) The updating can be done via console5) In console can be configured internet via: static IP , DHCP , PPPOE and preferably to have support for USB modems.
View 8 Replies View RelatedI have a fedora 10 box with two network card on eth0 I have a pppoe connection to the internet, on second card eth1 I share my internet connection end I set up a samba server but I don't know if the settings are good. How to do this settings right to work fine, the ip are assigned by dhcp I don't use any static ip .When I try to browse the internet from the other computers some site's like {.com ; .org ; .info} are block, other site from {.ro} are working. Someone tell me something about turn off all my filters, but I don't know where to find this filter to turn it off. And when I use samba I can't have and internet access or vice versa. My network look like that:
Code:
eth0
|<--pppoe connection
|
MyComputer
(fedora 10)
|
eth1
|
switch
|
comp.1 comp.2
Win OS MacOS
I have installed CentOS in multi-boot set up.when i am trying internet thru win7,its working fine but when i am tryin to connect using CentOs,its not working.I have tried and changed the mac address to the one that is on windows(this worked fine with ubuntu) but the issue remains in CentOS.
View 8 Replies View RelatedI have installed fedora 14 minimum install and I have configured my machine for Static IP but now i cant reach any external sites or repository, in fact all i can do is ssh to the box. below is the configuration in my /etc/sysconfig/network-scripts/ifcfg-eth0 file:
DEVICE="eth0"
BOOTPROTO="static"
BROADCAST="10.27.18.255"
IPADDR="10.27.18.117"
NETMASK="255.255.255.0"
[Code]....
and my DNS is setup to point to my ISP's primary and secondary DNS servers. I have brought the interface down then up after each change but still cannot ping anything.
I installed RHEL 5 today and set my network. Did it as follows:Eth0 connectionPrimary DNS 192.168.1.1When I click on Activate, it says:8139too device eth0 does not seem to be present, delaying initialization.This message shows no matter how many times I log out or restart.I don't know what the heck is the problem. I've done the essentials but still it's not working. I looked up on the net but people were saying things like ifconfig and lspci, and at the end still weren't able to solve it. I don't know all this since I'm new to Linux. Another important thing...after facing this same problem some time ago, I installed Centos which asked for internet settings right at the time of installation. And after logging in for the first time, I was able to use internet without any problem. How come internet works on Centos (which is a copy of RHEL) without any problems, but not working on RHEL itself?
View 14 Replies View RelatedI have wireless adapter USB rt1878 working fine.I have to setup pppoe to make internet connection?I need this help?
View 3 Replies View Relatedi run into a very annoying thing, usually take less than a second to connect to the internet using pppoe-start but today after a new installation of slackware 13.1 take a couple of secs to connect.
now:
# pppoe-start
Connected!
usually:
# pppoe-start
. Connected!
i'm using kernel-generic-smp-2.6.33.4, i even rebuilt the rp-pppoe package but it's the same thing. same behaviour was also in the previous release using kernel 2.6.29.6 due the broken forcedeth in that version of kernel, but on ArchLinux using the same version of kernel works normally.
I have wireless adapter USB rt1878 working fine.I have to setup pppoe to make internet connection?I need this help?
View 1 Replies View RelatedI have a ppoe internet connection. I was easier and faster to configure it in Yast than in Windows XP. When
The provider here sometimes goes through some problems and the connection may disappear and return at any unexpected moment. In Windows there is a icon on system tray that dysplays such information and I know when the connection is gone. It also allows me to try to reconnect manually. Where do I find these information on Opensuse here do I manage to reconnect. In Windows it was also possible to set the connection to re-dial automatically when it was out. It was very useful if it failed in the middle of a download, the system reconnected and the download manager retried until download resumed. Is there some way to adjust opensuse to reconnect automatically when connection fails or some software that does it? Furthermore, is there a good download manager that works in Opensuse that pause, accelerates downloads and retries when connection fails?
i have a routed and a PPPoE type internet connection, recently i tried a thing in terminal with the pppoeconf option since the network manager has problems with connectiong to the internet with a pppoe DLS connection, or anyway in my case it does not work. Ok i did the pppoeconf thing i inserted my pass and my user and left the program to do its thing, ok it all worked fine but then i restarted my system and suddenly the network manager did not want to recognize my network it hat as options some weird ipupdown options for connection and when i tried the pppoeconf thing again it did not work. what could i do to reactivate at least one way my connection, if i understood correctly the terminal type connecting and the network manager are two different things. now i am using my router and it should connect but the network manager still does not see the connection.
View 3 Replies View RelatedI cant get my wired internet connection to work. The command 'dpkg -s pppoeconf' returns ' installed ok installed'. My connection is through a router which is probably in a semi-bridge mode and I need to dial a connection to get the net started. The connection Auto eth0 is setup properly with the correct cloned MAC Address (that of my laptop).
I've also executed 'sudo pppoeconf' and ran the whole series of steps which towards the end said that my connection will be set on boot. However, the net doesnt work directly and I dont know how to dial manually either. 'sudo ifup eth0' returns 'interface eth0 already configured'. I tried some 10-15 threads but none worked. Ubuntu is handicapped without internet.
i configured my laptop (running UBUNTU 10.04 LTS) for my broadband (bridge mode). I did that using PPPOE CONF command. Everything goes ok but only prob is i have to run this command and configure my net every time i restart my system. What i need is it should connect to the net whenever i use the PON DSL-PROVIDER and must turn off by using POFF..
View 1 Replies View Relatedi have to different routers in my home. One is at&t dsl modem other is dlink wireless n router.
I have my ubuntu server connected to my att modem as this is the only way I can get it to work. As I can only connect to my server from the outside of my home.
Problem is my desktop and laptops use the dlink because its faster and giver me more bandwidth so everything in my home is wirelessly connected to it.
I use ubuntu as web server, proxy server, and dns server. I have all my computers useing the proxy server my just inputting my proxy address as 192.168.1.0 which is my ubuntu address. But my computers use 192.168.0.0 as this is how dlink is setup.
So anyone know how I can get all my pc's on the network 192.168.0.0 to connected to my samba server which is on 192.168.1.0? Can I setup my dlink dir-615 as a access point? So that it shows up in the 192.168.1.0 network. Or can i configure my pc's to look into the 192.168.1.0 network to see the samba server?
We need to implement ntlm for apache[URL]... Apparently this requires joining our linux host to our domain. however we have two active directory servers in seperate domains, one ads is for users only, the other is for computers only. Testing kerb and joining your linux host to the domain requires you enter in a user that has permissions to join the domain on ADS. But how do I join a computer to a domain where my account does not exist, the ADS that only contains computers is the one I need to join.
View 2 Replies View RelatedI am trying to configure samba for anyone of the scenarios in the subject. here's what my smb.conf looks like:
Code:
workgroup = RnD
[Samba Share]
comment = Samba share on Ubuntu!
path = /srv/sharedfolder
available = yes
[code]....
The error while trying to connect to the share is:
smbd/service.c:make_connection_snum(1082) Can't become connected user!
I would like to configure an access to folder
/fileserver
for two services : Samba and VSFTPD
How to do it ? How to create folder rights that samba and ftp user will have an access (read/write/delete) to all directories in /fileserver.
My system is CentOS. I`m starting samba and vsftpd like a root (/etc/init.d/vsftpd start etc.)
installed ubuntu 8.10 64bit on left over parts for file serving with windows 7, tried the sample config file that installed with it with no luck, then tried new config file, looking at the samba.org website and other peoples configurations i came up with this
[global]
netbios name = NETBIOS_NAME
workgroup = workgroup
security = user
[code]....
I'm trying to configure Samba with a GUI. I also can't find smbcontool, which I used on my previous 9.10 installation. Is the same thing available for 10.04? I can't seem to find it, no matter how many repos I enable.
View 3 Replies View RelatedFirst off I would like to install a GUI for samba. After that I want to set up my network so that router stays as the server for the network I have four windows computers already hanging off of the router. This machine which has Slackware on it is hardwired, directly connected, to the router via cat-5 cables. I have samba installed already and I just need to configure it correctly.
View 4 Replies View RelatedI am using samba from a windows client to put some rights access on FTP server on Linux. created a folder and I want that a user can write in that folder (put a file for example), but, once he did that, he can't delete or rename the file.
View 5 Replies View RelatedI have just configured samba on suse linux. I can see it in the windows workgroup but i cannot access it. When it says the server is not accessible. You might not have permission to use this network resource.I have attached a copy of smb.conf
View 2 Replies View Relatedsamba quit working after win7 I'm new-ish to linux(not using ubuntu tho, but servers)i don't know what PID is.. i just installed a new ubuntu server of an old computer, for file sharing in workgroup with samba, and a little apache server running webmin is also running, giving me an error when restarting samba all worked very well untill i used win7 to access the \server this blog post have a fix for vista7? connecting to samba, but wont fix my problem after i connected to the share with win7 nothing seems to work
Quote:
# service samba status
* nmbd is running
* could not access PID file for smbd
and this:
# service samba start
* starting samba deamons [fail]
restart wont work, neither do reboot the server. I am clueless some of my research is pointing me to /var/run/ and there is no smbd.pid there, not in any folder (nmbd.pid exist) i found something
# service samba reload
* Reloading /etc/samba/smb.conf smbd only
No process in pidfile `/var/run/samba/smbd.pid' found running; none killed.
[ OK ]
i dont have any smbd.pid in the samba dir, should i create a new one.. and where do i get the PID -id that should be inside?