General :: Cannot Reach The Internet After Configuring Static IP
Jan 13, 2011
I have installed fedora 14 minimum install and I have configured my machine for Static IP but now i cant reach any external sites or repository, in fact all i can do is ssh to the box. below is the configuration in my /etc/sysconfig/network-scripts/ifcfg-eth0 file:
DEVICE="eth0"
BOOTPROTO="static"
BROADCAST="10.27.18.255"
IPADDR="10.27.18.117"
NETMASK="255.255.255.0"
[Code]....
and my DNS is setup to point to my ISP's primary and secondary DNS servers. I have brought the interface down then up after each change but still cannot ping anything.
View 4 Replies
ADVERTISEMENT
Aug 2, 2011
I used my computer this morning, but when I returned this evening, I am unable to reach the internet. Also the light on the mobo where the ethernet cable is plugged in is steady yellow.
My limited experience would tell me it is a hardware failure, but it seems so strange with nothing happening during the day. How might I best diagnose the problem?
View 8 Replies
View Related
Aug 29, 2010
I think that i lost my memory, because i completely forgot how to accomplish this.
I have a WEB/MAIL server configured to work on a static IP address, lets say 200.11.22.33.
Now I wanna point a domain to that server to get the services up and running, lets say mydom.com ...
The static IP Address is assigned by my Internet Provider.
I'm lost in the part of connecting the domain with the server.
I have the domain DNS pointing to the ISP name servers, but I don't remember if this is the correct way, or if I have to setup my own DNS server.
View 4 Replies
View Related
May 7, 2010
I have installed CentOS in multi-boot set up.when i am trying internet thru win7,its working fine but when i am tryin to connect using CentOs,its not working.I have tried and changed the mac address to the one that is on windows(this worked fine with ubuntu) but the issue remains in CentOS.
View 8 Replies
View Related
Dec 16, 2010
I finally managed to install pppoe and pppoeconf. When I type command 'pppoeconf' , it invokes some window and I put username, passwd etc. But my net connection won't start. I have posting the output of various commands related to networking.ifconfig
Code:
eth0 Link encap:Ethernet HWaddr 00:0f:b0:4a:54:a7
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20f:b0ff:fe4a:54a7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1388 errors:0 dropped:0 overruns:0 frame:0
[Code]...
View 10 Replies
View Related
Apr 5, 2011
I installed RHEL 5 today and set my network. Did it as follows:Eth0 connectionPrimary DNS 192.168.1.1When I click on Activate, it says:8139too device eth0 does not seem to be present, delaying initialization.This message shows no matter how many times I log out or restart.I don't know what the heck is the problem. I've done the essentials but still it's not working. I looked up on the net but people were saying things like ifconfig and lspci, and at the end still weren't able to solve it. I don't know all this since I'm new to Linux. Another important thing...after facing this same problem some time ago, I installed Centos which asked for internet settings right at the time of installation. And after logging in for the first time, I was able to use internet without any problem. How come internet works on Centos (which is a copy of RHEL) without any problems, but not working on RHEL itself?
View 14 Replies
View Related
Feb 27, 2011
I use Fed 14. I have China Telecom internet. The wired dsl connection works fine, but the wireless won't work. It has WPA security. The password taken from beneath the router is n2nqrcqx. This password is accepted. Network Manager says I am connected to ChinaNet-TRtk, but in fact, I can't reach the internet via wireless. If I disconnect the cable, I can't get through. I have the settings on automatic dhcp. I have nothing in BSSID, I don't know what that is. I unchecked the box 'require ipv4 addressing for this connection to complete' Ditto that for ipv6.
View 2 Replies
View Related
Mar 4, 2010
I recently upgraded my HP DV7 to 11.2. I did the install with wired network connection, my WiFi is always on as well. Install went fine, ran updates via YAST. I am running KNetworkManager, it loaded, configured eth0 and wlan0, prompted me for WEP keys and showed both connections working OK. I later found that when eth0 was disconnected, wlan0 was still connected but I could not reach internet sites. My router address was set as the gateway address and the DNS server address. Following several items on the forum, I tried 'dig' and 'route' commands.
I found that
Code:
HPDV7-Linux:/etc # dig [URL]
; <<>> DiG 9.6.1-P3 <<>> [URL]
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 28307
;; flags: qr rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 0, ADDITIONAL: 0 .....
;; Query time: 12 msec
;; SERVER: 192.168.10.1#53(192.168.10.1)
;; WHEN: Thu Mar 4 07:01:19 2010
;; MSG SIZE rcvd: 69
returned a valid URL for that server - DNS seemed to me working properly via my router.
I found that
Code:
route
returned:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.10.0 * 255.255.255.0 U 2 0 0 wlan0
loopback * 255.0.0.0 U 0 0 0 lo
No default route showing.
I then opened the Network Manager connection editor, went to edit for the wireless connection and found under the IP_Address tab, Routes option box that both
Code:
Ignore automatically obtained routes
and Use only for resources on this connection were enabled, I believe by the install process.
Unchecking these yielded
Code:
HPDV7-Linux:/etc # route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.10.0 * 255.255.255.0 U 2 0 0 wlan0
loopback * 255.0.0.0 U 0 0 0 lo
default DD-WRT.capenet 0.0.0.0 UG 0 0 0 wlan0
and internet connectivity now working.
View 1 Replies
View Related
Aug 2, 2011
I used my computer this morning before leaving for the office, but when I returned this evening, I am unable to reach the internet. Also the light on the mobo where the ethernet cable is plugged in is steady yellow.
My limited experience would tell me it is a hardware failure, but it seems so strange with nothing happening during the day. How might I best diagnose the problem from within Ubuntu (10.04)?
View 4 Replies
View Related
Mar 31, 2010
I was able to connect to internet using PPPoE until I configured Samba network and set the machine as its server; does this two related? Is it possible there's a conflicting configuration, say DNS server config for example?
View 2 Replies
View Related
Feb 3, 2010
Suse 11.2 > updated Feb 2 using the Update UI applet.
I had internet connectivity prior to installing the updates. Now I can't reach the internet since installing the updates. I can reach my router, log in to the router I also ping the router but I can not ping the WAN side ip on the router.
When I boot into redmond, no issues, which is what I'm using as I write this.
I have security enabled, WPA2 Personal, not that I think that is an issue as I can reach the router, my server, network printers, and PC's.
I am running a Linksys router but have replaced the standard Linksys software with DD-WRT v24-sp2 build date 12/28/09 std. One note, DD-WRT does hand out IpV6 address but I have disabled FF from using IpV6 address along with the network connection configuration applet from accepting them. (I don't remember the applets name)
In the redmond world this would be a certificate error, is this the same type of an issue? If so how do I fix it?
View 9 Replies
View Related
Feb 12, 2010
I have a Windows XP virtual machine under Virtualbox PUEL 3.1.2. I have always been able to browse the Web or do anything else I wanted over the network.
Suddenly, the guest XP machine can't reach the Internet any more. There is no indication of any problem with the network connection. I checked my router, and the virtual machine is indeed getting assigned an IP address. So why can't it reach the internet?
Yes, the virtual network adapter is in bridged mode. It always worked that way before. I can see local network shares from the virtual XP machine, and even reach the Apache server running on the host OS (Ubuntu 9.10 64-bit).
Also possibly significant: Even though the virtual XP machine is detected by the router & assigned an IP address, the printer attached to the virtual XP machine cannot be seen by another Windows machine (a real one, not virtual) on the network. I never had a problem sharing the printer before. I have to share it from a virtual Windows XP machine when I'm running Ubuntu because there are no Linux drivers available (it's a Winprinter).
View 2 Replies
View Related
Sep 21, 2010
I have set up my guest OS in VirtualBox so that it has a static ip and is using a bridged adapter. As a result, I can see the webserver that's hosted in guest from my host OS's web browser. However, for some reason my current setup does not allow my guest to reach the internet. What settings do I need to enable both?
View 1 Replies
View Related
Jul 11, 2011
I've installed apache2 on ubuntu 10.04 and everything works fine, but when I use functions that needs to connect to Internet, it doesn't work. Is there a simple setup I've forgot? I've been searching and looking for a solution, but I'm stuck!
View 9 Replies
View Related
Feb 20, 2010
I need a linux distro who provides the following:1) Has an partitioner who can resize fat , ntfs ,ext* , .....filesystems.2) Has an excellent hardware support3) The installer can install console or graphic mode 4) The updating can be done via console5) In console can be configured internet via: static IP , DHCP , PPPOE and preferably to have support for USB modems.
View 8 Replies
View Related
Aug 3, 2010
I am struggling with what might be a minor problem. I have a home computer which I would like to setup as a webserver and hence give it a static IP address. It is connected to by wire to a router that is connected to the WAN via PPPOE. If I enable the network card on DHCP it works fine in browsing the web. If I now set it to static IP address it does not brown. Essentially I use the command setup to run the static IP setup. I then set my IP address to 192.168.254.X , the subnet mask 255.255.255.0 and the default gateway to 192.168.254.1 (this is the router connected to the WAN). I am able to ping the router, however when I try and browse on static it does not work. Your help will be most appreciated as this has taken way too long to solve and I have Googled as much without success.
View 5 Replies
View Related
Jan 30, 2010
I'm trying to give some windows users a permanent connection to a samba share behind a firewall over the public Internet. I know I can give them access with something like winscp (which they have done) but really I'd like to do it with a VPN so it seems seamless to the user. However I have no idea how to set up the server to support this and am finding the documentation a bit confusing. The samba share is on a Debian box and the firwewall is a Linksys WRT54GL.
View 1 Replies
View Related
Jun 17, 2010
I wanted to give my computer a Static IP so that I can easily connect to it from other computers: ie Mythbuntu.This is what I did. I set it with a static to 192.168.1.107. My gateway is set to 192.168.1.1, and 255.255.255.0 for the subnet mask. I'm using default settings on a Linksys wireless router.I've rebooted several times.Nowthen, I can connect to the computer from my laptop via the IP.Even my Iphone can connect to the computer through that IP, so I've successfully set it's IP to static, but I cannot connect to the internet.
View 9 Replies
View Related
Jan 20, 2010
I have ubuntu 9,10 and 7 repositorie disks I bought from osdisc.I installed ubuntu next to widows xp 3.I can't seem to connect to the internet or configure my system to do so.My us robotics usb 2.0 modem works great in xp but not at all in ubuntu.Is there someone out there willing to help me step by step?Or in anyway possible.Directions on how to or where to go for help.I'd really like to not be dependent on Microsoft completely. My telephone number is 903-566-3590. My fax is 9035660030. My address is 12862 Sandy Point Drive Tyler, TX 75707
View 1 Replies
View Related
Jun 11, 2010
I recently bought a dell inspiron 14 n4010 and i've installed windows and Ubuntu 10.04 in it. The problem is that i'm not able to access internet in my ubuntu. I'm using asianet broadband connection and i'm able to get internet in my desktop when i connect the cable to the system. But when i did the same with ubuntu 10.04 in my laptop, i'm not able to get internet access. I'm able to access internet in windows though. But i hate using windows.
View 9 Replies
View Related
Mar 26, 2011
I am using ubantu 10 and broadband where userid and passwd has been configured in router box. So when I connect this from windows its automatically connected (using ppp0e and dhcp), whereas in linux it could not connect.
View 2 Replies
View Related
Apr 21, 2010
is there a possibility to connect to my router admin zone from internet using wan ip? from lan I can do that using 192.168.x.x IP but when Im in work and something go wrong at home how can I check configuration of my router from outer world instead of lan?
View 7 Replies
View Related
Jan 11, 2010
I'm having an issue with a new install of 9.10. I've set the ip address in /etc/network/interfaces and I've also set DNS servers in /etc/resolv.conf.
The issue I am having is that no address resolves, nor can I ping outside of my LAN. I've wanted to avoid using the GUI network setup because it hasn't been saving the information correctly. Here are how the files look code...
I don't know what eth1 is; I only have 1 ethernet connection in that machine, so I'm thinking it may have something to do with that. However if the machine is using eth1 (which has no address) than it follows that I shouldn't be able to locally ssh or vnc into it, right?
View 2 Replies
View Related
Jan 12, 2011
I set up a static IP address yesterday, following the instructions at the top of this page and since my machine no longer connects to the internet (although all other machines are connecting fine, so I know it's a result of this change).
View 6 Replies
View Related
Jan 10, 2011
I am trying to get a Slackware server up and running. I got a static IP working kinda. The computer gets a response when I ping the router but not the internet. Basically it can communicate with other computers on the network but nothing outside of the network. Its not a problem with the router because I have a couple other computer with static IPs. Also the network card works fine as it can get on the internet fine normally.
[Code]....
View 9 Replies
View Related
Feb 23, 2010
I just installed a command line version of karmic to an old desktop. During installation, DHCP failed, so I attempted to configure manually (without really knowing what I'm doing) and wound up without a connection. I've been searching for solutions, but really don't understand what I need to do. A million thanks to anyone who can help me get up and running (or at least give me a push in the right direction).I can either connect the computer directly to the cable modem via USB, or directly to my wireless router via ethernet cable. I know what the ip address for my laptop (which is connected wirelessly to the router) but don't know if that would be the same for the desktop or not, and don't really know anything else.
View 3 Replies
View Related
Jun 18, 2010
I have latest ubuntu and I have made 3 vm's for them.
VM 1: with 2 NIC cards, one is NAT connected directly through my host machine to the internet with ip address 192.168.190.142. Second NIC card is "host only" with ip address 192.168.0.10
VM 2: with 1 NIC card, "host only" and ip address 192.168.0.100
I want VM 2 to connect to the internet but through VM 1. for this I used following configuration in
Code:
/etc/network/interfaces,but it is not working[code]....
I have given my VM 2 the gateway of VM 1 but it is not going through.P.S: both machines are pinging each other properly.
View 1 Replies
View Related
Jun 18, 2010
I have latest ubuntu and I have made 3 vm's for them.
VM 1: with 2 NIC cards, one is NAT connected directly through my host machine to the internet with ip address 192.168.190.142. Second NIC card is "host only" with ip address 192.168.0.10
VM 2: with 1 NIC card, "host only" and ip address 192.168.0.100
I want VM 2 to connect to the internet but through VM 1. for this I used following configuration in
Code:
/etc/network/interfaces
but it is not working
Code:
auto lo
iface lo inet loopback
auto eth1
code....
I have given my VM 2 the gateway of VM 1 but it is not going through.
P.S:
both machines are pinging each other properly.
View 8 Replies
View Related
May 18, 2010
In windows, when I use an HSPDA modem, internet traffic will be automatically directed through it. Everything will go back to normal once broadband connection is disconnected. In fedora 12 this is not the case, internet traffic will still go through the lan interface. Is there a way to mimic windows behavior in linux?
View 3 Replies
View Related
Feb 17, 2009
I am a windows user with no linux experience prior to Friday. Im setting up a music server (SqueezeCenter) running Fedora 10.
With the help of posts of this site Ive made good progress with complicated stuffnamely getting Samba and VNC working. My Fedora machine and my windows machines now see each others shared files, and I can control my Fedora machine from my windows machine. (The Fedora machine will ultimately be headless.)
But Im having trouble with a seemingly simple issue setting up my Fedora box with a static IP address. With DHCP enabled on my network Ethernet adapter, all works fine. I then used the System>Administration>Network menu to disable DHCP and to assign the same IP address that DHCP chose. When I do this, two cases need to be distinguished:
1. If I keep the box checked for Controlled by Network Manager, the Network Manager Applet reports a network connection, I nevertheless cannot access the internet, but my Fedora machine is able to communicate with my Squeezebox music player (connected to my network via my DSL modem Ethernet connections, and with a fixed IP address). 2. If I uncheck the box Controlled by Network Manger, then the Network Manager Applet reports no network connection and my Fedora machine is not able to communicate with my Squeezebox music player (and I of course have no internet connectivity).
Ive seen references on other posts suggesting that the Network Manager service be disabled. But I see no way to manually configure the network.
View 4 Replies
View Related
