CentOS 5 Networking :: Configuring 5 To Use Gateway?
Mar 22, 2010
Recently my motherboard went out, I replaced it and booted centos 5. All went well except sound, video tuners and netoworking. The sound I re-configured, and have gotten tuners working but I am running into trouble with the new network card. The networking setup is;
DSL wireless router/modem IP 192.168.0.1 connected to XP computer through WIFI IP 192.168.0.3. all set to subnetmask 255.255.255.0 and with DNS servers 192.168.0.1 and 205.171.3.25 the XP computer is the only one that supports my wifi card. On wired LAN I share that connection to 4 devices. 3/4 work well, my cent os 5 box will not connect. here are the lan settings:
win xp: IP 192.168.0.60 255.255.255.0
mac 8.6: IP 192.168.0.34 255.255.255.0
blueray: IP 192.168.0.65 255.255.255.0
[code]....
View 9 Replies
ADVERTISEMENT
Apr 12, 2010
I have a requirement of switch between wireless network with a single wireless device. First it should be switched to adhoc mode and then after sometime switch to infrastructure mode to establish internet connection. Everything works fine except the gateway settings.
I have used:
system("route add default gw x.x.x.x dev wlan0") to set the gateway, where x.x.x.x is gatewayip address.
I have used this whenever switching happens in addition to ifconfig command to set the ip address and netmask. But this is not setting the gateway ip address. How to set gateway IP address?
System details below
OS :CentoS 5.3
Kernel :2.6.18
View 3 Replies
View Related
Jun 15, 2011
We have a sendmail server located in a DMZ that has normally been able to send SMTP traffic to whatever destination is listed in the address of any given e-mail message. A recent change in network configuration has introduced an e-mail gateway that all servers need to send smtp traffic to in order for the messages to go out to the Internet.
View 1 Replies
View Related
Apr 28, 2009
And I'm currently working on a new CentOS 5 install I've made on a computer I've got.. So I'm now trying to get that computer to reach my home network through one of my other computers, which have got XP installed. I've configured the XP computer to act as a gateway from one network card to another, and It works with another XP pc, but no luck with my CentOS 5. I used this link [URL] And I configured the correct network card.
So.. the IP of the XP machine is 192.168.1.70, which I have set as a static. So that the CentOS will find it. And I've connected the (fully working) network cable correctly.
What do I have to do?
I have configured the CentOS to recieve an IP dynamically. (dhcp).. Might that be the problem? (well.. one of the problems.. I've tried to set it to static.. ...?)
Is there more to it than this? I mean when I'm working on communication through an XP machine... ?
View 1 Replies
View Related
Jan 12, 2011
My company hosts five Servers with CentOS 5 installed in a Data Center. The Data Center assigns a VLAN to each customer so that they can organize customers and also count traffic. The VLAN assigned to my company is in the form 62.103.X.X with a subnet mask 255.255.255.240 so the IPs that we can use in our Servers are 13. The first IP in the VLAN (for example 62.103.1.1) is the Gateway and the rest, that are calculated from the subnet mask, are assigned to servers(62.103.1.2 up to 62.103.1.14).
The problem I have is that we have run out of IPs in our VLAN. We have used all IPs and we want some more. The Data Center can assign new IPs but not grow our VLAN IPs by expanding the subnet mask. So they gave us a new VLAN with some IPs (for example 62.104.X.X with a subnet mask 255.255.255.192) They told me that I had to use as gateway the gateway of the first VLAN 62.103.1.1 and assign the new IPs as usual. So I assigned to one of the CentOS 5 servers the IP 62.104.1.2 and set the gateway to 62.103.1.1. Unfortunately this did not work and we could not establish connectivity to the Internet.Is it possible to assign a gateway outside of the IPs that are in the subnet? Could it be a problem with the VLAN setup by the Data Center?
View 4 Replies
View Related
Jul 2, 2010
I posted it on another forum, but could not get response,So I have this cenOS, Ubuntu and windows operating system running on virtual machines.Now I gave them manual ip address, both ubuntu and windows machines can ping the default gateway, but not the CentOS.It should forward 0.0.0.0. to my cisco router address(192.168.5.254),
View 4 Replies
View Related
Jan 13, 2010
I have an HP BL460c G5 with 5.3 installed fresh
it can ping its own IP address just fine
its a bit slow but constant pinging the switch its connected to
and i get alot of Destination host unreachables(a few do get through) when pinging the gateway
port on the switch is hardcoded to GB/full. and the server itself reads that its connecting at GB/full.
View 10 Replies
View Related
Feb 3, 2010
The install actually seemed to go pretty smoothlyIt's a dell pentium4 with 128mbyes it installed textuallyI start the gui with 'startx'but the question I have is for the more experienced CentOS people.when I login as rootI am trying to figure out how to get my machine onto the internet.I had figured the OS would have NO problem with a Linksys 10/100 pci cardsince the OS has the latest drivers and all.The system reports the NIC as a "ADMtek NC100 ethernet" card (eth0)it also reports that the status is "ok"Now, I've seen the NIC when it's plugged into a hub (during the O/S install)and it DOES make the hub's light flicker when it tries to "talk" to it.but when I have it plugged into my Cable Modem (for internet) it's not doing anything.
During the install I SAW the NIC making the hub lights flicker... so I know the interface WAS doing "something".but nowwhen I go into the gui and I try the NetWork Admin , and I try to "activate" the card.Nothing.Am I NOT doing something that I SHOULD be doing?fconfig? (at the command line?) ifup? I would have thought I'd "activate" it with the gui ok...I'll keep poking around.I'm just a little surprised is all. Ubuntu 8.1 had no problem "discovering" and using a wireless Linksys cardTHIS operating system is even newer
View 11 Replies
View Related
Dec 19, 2010
I could not able to configure the default gateway ip address onto the system. i use the route command (" route add default gw 192.xxx.xxx.xxx eth0 ") to add a default gateway onto the routing table but it is "disappear" in the routing table when i had restart the service network.
View 3 Replies
View Related
Jul 10, 2009
I have to servers online, both are connected to a virtual rack and both have public inet IPs. The thing is that I want the communication between the servers to be handled locally. This is my ifconfig from one of my servers,
eth0 Link encap:Ethernet HWaddr x:x:x:x:x:x
inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.248
inet6 addr: fe80::21d:9ff:fef1:e665/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:114342 errors:0 dropped:0 overruns:0 frame:0
[Code]...
View 1 Replies
View Related
Jan 24, 2011
i've got a select based application that wants to support a large number of mostly idle connections. the code is java and works on windows, suse enterprise linux, mac os x. it does not work on centos 5.5 (32-bit, 2.6.18 kernel, 1G of memory).
i've read and followed the directions in various articles about tuning linux for large numbers of connections (including the C10K problem), and gotten the number of sockets up to 3200.
these didn't make any apparent difference:
[URL]
on windows, i can get up to around 78,000.
on suse enterprise linux (a few years ago), i got up to 90,000. that's where i got bored and stopped.
on my mac laptop with os x (snow leopard), i got up to 10,500.
i have used ulimit -n 10240
my current goal is 10k sockets.
the test is that i'm opening one socket at a time until it fails. when it fails, many of the sockets which have already been opened also fail, in one giant cascade. sounds like a buffer / memory problem.
each group of 64 sockets gets a thread to manage select calls for them. thus i'm only using around 61 threads total when it fails.
View 3 Replies
View Related
Mar 31, 2011
configuring DHCP server with two NICs. I need DHCP server with 2 NICs:
eth1 - 192.168.103.11
eth2 - 192.168.123.11
The client also has two NICs and suppose to receive ip addresses eth1 from 192.168.103.0 and eth2 from 192.168.123.0 Here is the dhcpd.conf from dhcp server:
ddns-update-style interim;
authoritative;
ignore client-updates;
[code]....
View 2 Replies
View Related
Feb 16, 2010
I've search for info on configuring ndiswrapper for the BCM4318 Wireless card. All I've been able to find is information on Ubuntu and Debian, which don't seem to use the same methods for configuration. Has anyone configured ndiswrapper for this or any wireless card on CentOS 5? I've installed 5.4.
View 7 Replies
View Related
Nov 15, 2009
I have a desktop that has a d-link DWL-520 wireless card, which was working under Windoze. Today I installed Centos 5.4 on the system , which went cleanly. I then used Network Configuration to set up the wireless card. I specified to use DHCP, set the SSID and authentication password. When I tried to activate the card I get these error messages
Error for wireless request "Set Mode" (8B06): SET failed on device wlan0 ; Operation not supported. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0.
The hardware manager seems to have correctly identified the card and chipset, (Intersil Prism 2.5) and installed driver hostap_pci which came with the distro. This web site seems to suggest that this is the correct driver: [URL] searching forums I've found a few references to these errors, but they were from several years ago, and for different distros and cards. I did find a reference to using Network Manager to configure the card instead of Network Configuration. I started the NM service and configured a connection using it instead, but still no luck.
[Code]....
View 15 Replies
View Related
Mar 4, 2011
I need to setup two ethernets in my Centos box. OK no problem both ethernet and 1 virtual works perfect. eth0, eth1 and eth1:0. I'm trying to set up diferent routes for eth0 and eth1/eth1:0 I need eth0 has a 192.168.1.1 gateway and eth1/eth1:0 192.168.1.100 gateway.I think I've tried almost every thing but always get one gateway for all the eth.These are my config..
/sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:XX:XX:XX:XX:XX
inet addr:192.168.1.168 Bcast:192.168.1.255 Mask:255.255.255.0[code]......
View 7 Replies
View Related
Jun 16, 2009
I have a CentOS 5.3 box with three network interfaces in it. Each interface is attached to a separate VLAN and I want traffic to stay on each network segment.What I can�t figure out is why I cannot get each interface to have its own gateway and everything gets sent through the default gateway.The basically takes my possible 3Gb total bandwidth and throws it down a single 1Gb pipe.Then on top of that, if I take down the interface (ifdown) that has the current default gateway,I loose contact to the other two interfaces.When I look at the routes, each one of the interfaces shows the gw as 0.0.0.0 and defers to the default route. So I delete the route and try to add a new route with:
[root@testsan ~]# ip route add 10.1.15.0/24 via 10.1.15.1 dev eth2
but end up with the error:
RTNETLINK answers: Network is unreachable
[root@testsan sysconfig]# cat network
NETWORKING=yes
NETWORKING_IPV6=no[code].....
View 5 Replies
View Related
Aug 12, 2010
I'm trying to configure SNMP service to send traps to SNMP server. I've installed net-snmp-utils, now I need to configure the "snmpd.conf" file...
View 2 Replies
View Related
Aug 9, 2011
I have a CentOS running. It is important to have my CentOS available when I am remotely connected to a VPN router. I tried to add a default gateway to the VPN router, but after reboot it goes away. How can i put this as permanent?
ip route add 192.168.2.3 via 10.0.0.1 dev eth0
View 2 Replies
View Related
Oct 5, 2009
I installed syslog-ng-3.0.3-1.rhel5.i386.rpm and at first blush it appears to be working fine to /var/log/messages. However it doesn't seem to be doing any other ancillary logging as defined in syslog-ng.conf (I've had to mod /etc/init.d/syslog-ng to look in /etc). e.g.
destination d_auth { file("/var/log/secure"); };
filter f_filter3 { facility(authpriv); };
log { source(s_sys); filter(f_filter3); destination(d_auth); };
I'm using a syslog-ng.conf which has served me well in the past (v1.6.9 on fedora).
View 1 Replies
View Related
Aug 11, 2010
where i can learn configuring DNS and apache
View 1 Replies
View Related
May 26, 2010
I've set a two-node cluster using Pacemaker/OpenAIS. I have only one network and if I break this one, the communication between node is interrupted ... With a ClusterIP resource, when network is breaked, then each node start the ClusterIP => 2 same IP .. Is there a way to define the prefered location of a resource when connection between these nodes is broken ?
A <==> B
If one of the node lose the network, then follow a previously written rule : start resource on A (for example). B will know than it's not the prefered node and so, will stop to serve. Possible ? This is because if both node are connected, but a problem between these node occur and client can join both node ... then the split brain is problematic ... A better solution is to add a rule when the split-brain occurs : all node wich can't reach the gateway have to stop all resources ... And so, if it's A wich lose the network, service will start on B and only B without any problem ...
View 1 Replies
View Related
May 7, 2010
I have installed CentOS in multi-boot set up.when i am trying internet thru win7,its working fine but when i am tryin to connect using CentOs,its not working.I have tried and changed the mac address to the one that is on windows(this worked fine with ubuntu) but the issue remains in CentOS.
View 8 Replies
View Related
Jul 11, 2011
I am trying to get a Linux (Slackware 13.37) working in a Windows networking environment. The IT support for this organisation does not extend to Linux support, so I'm limited in what help I can get for this.
I'm trying to get to the point where I can get to the internet to download what I need on this Linux machine.
The situation is this (*fictitious addresses used) -My Linux machine uses a fixed IP address (10.100.150.21)
My Windows machine uses a DHCP assigned IP address (10.100.150.213)Both Linux and Windows machine are configured to access the gateway server (10.100.150.1)So, I can ping the Linux machine from the Windows machine and vice-versa.I can ping the gateway machine from the Windows machine.I can browse Windows Shares on the network via SMB from the Linux machine.I CANNOT ping the gateway machine from the Linux machine with the Destination Host Unreachable message being the error message.
For actual internet access I need to access a proxy server but since the Linux machine can't even ping the gateway server, it fails to ping the proxy.Now, I have been told the gateway is a HW based router and for Windows machine they use some software for authentication to connect to the network. This software isn't available for Linux, so that's why I've been told to use a fixed IP address.My experience of networking is pretty basic and most of the Linux setup is done via running Slackware's setup program.
View 12 Replies
View Related
Jul 31, 2011
I installed the Centos 5.5 on a WM instance. Run out of space after doing the updates. It is very difficult to keep re-partitioning /
I tried to install a new instance but it doesn't let me configure the disc and it just goes and install the OS.
How can I use the good old installation options etc?
What happened to control? This became a control nightmare.
View 2 Replies
View Related
Feb 10, 2009
Am using Icefaces1.7.2 in tomcat5.5.23 in Centos5( jdk 1.6.06 and jre 6u11 and no X window system in my server ).. Am getting the error(java.lang.Error: Probable fatal error: No fonts found) when am using the functions getFontMetrics() and drawString() methods in my Captcha Image Generation programs. I am only using the fonts that me retrieved using ge.getAllFonts() ( i.e., the fonts available in the system ).
View 6 Replies
View Related
May 13, 2009
I've got a server with several different virtual hosts on them, e.g. host1.com, host2.com, host3.com.
Is there a way I can set up an email alias just for an individual domain?
e.g. I want to set up help@host2.com, but not to have help@host1.com or help@host3.com.
I can't see how to do this in the /etc/aliases file...
View 2 Replies
View Related
Jun 30, 2011
I've installed CentOS 5.6 to my laptop, primarily to use some simulation programs. With much help of google I'm getting my hardware and software to work quite well, but I still have some troubles.My first problem is my Synaptics-Touchpad. It is extremely sensitive and I am not able to scroll. Is there any application which allows me to configure it properly? Before CentOS, I've tried openSUSE 11.4, where there was an application especially for configuring synaptics touchpad (dont't remember the name though). In general, the "feeling" of the touchpad was way much better under openSUSE, but I can't define that properly. I have a bluetooth mouse (Dicota Blue Light) conntected to my laptop, which is working fine except for the scroll wheel, which doesn't work at all. How can I activate it?
View 3 Replies
View Related
Jan 17, 2011
full steps of configuring mail server in CentOS 5.5.
View 4 Replies
View Related
Nov 26, 2009
I am using Centos 5.4 on an Intel DG451D Main Board. Two SATA drives in RAID1 mode via the main board's built in AHCI controller. It seems to work just fine but I would like to be able to monitor the state of my drives and controller, especially during a re-build and make configuration changes etc if possible, so new drives can be added etc from within the OS. Is there a way to do this within Centos or am I stuck with using just the BIOS configuration system? Apologies if this is a stupid question - I am pretty new to this and have spent several hours trying to find a solution to my question but to no avail.
View 1 Replies
View Related
Nov 10, 2010
i have linux server application based on centos 5 that run httpd daemon from /usr/local/pf/conf/httpd.conf which is generated from the /usr/local/pf/conf/templates/httpd.conf.apache22 file
the problem is every time i run my linux server application i am not able to access phpmyadmin unless i stop my linux server application which is stop it httpd daemon then start "service httpd start"
i have been told by forum moderator to create an alias for my phpmyadmin in Virtual Host but it stil dont work, i am not able access my phpmyadmin site
this is what i have done to solve this problem
- open /usr/local/pf/conf/templates/httpd.conf.apache22 file then look for <VirtualHost *:%%admin_port%%>
- add Alias /phpmyadmin "/usr/share/phpmyadmin" (Failed)
- add Alias /phpmyadmin /usr/share/phpmyadmin (Failed)
- add Alias /phpmyadmin "/usr/share/phpmyadmin/" (Failed)
[Code]....
NB : my phpmyadmin is install on /usr/share/phpmyadmin with /etc/httpd/conf.d/phpmyadmin.conf as phpmyadmin configuration file
why i still cant open my phpmyadmin site ? or why i cant run phpmyadmin together with my linux server application because it use the same daemon (httpd daemon)
View 1 Replies
View Related
