General :: Know Wireless Network EVDO Datacard Over Puppy System?

Jan 21, 2011

I have recently downloaded live cd of Puppy Linux and boot successfully from it. But, I could not connect my BSNL EV-DO datacard as no wireless network connection is detected by Puppy. What should I do? How can I configure my BSNL EVDO Datacard over Pupply Linux? Plz.

View 1 Replies


ADVERTISEMENT

OpenSUSE Network :: Internet Datacard Gets Disconnected After Sometime?

May 21, 2011

If i leave my laptop idle for sometime, my usb datacard connection gets disconnected. I know its a dial-up connection and if no application is accessing internet it disconnects on its own. The problem over here is when i click on the icon and click on activate it won't happen. So, i have to unplug the hardware and then re-insert it to make it work again.I went through a site, there they have mentioned a work around that is to keep a ping command always running. I'm fine with that, but why do we need to remove the hardware n re-insert it to make it connect to the internet again

View 3 Replies View Related

General :: Wireless Puppy On An Old IBM T30?

Mar 2, 2010

I'm fairly new to linux, I can't get puppy to connect to ANY wireless network, protected or not. The driver autodetected my wireless card (IBM high rate wireless LAN with modem II) as an Intersil Prism 2.5 chipset, but it will not work. I wonder if the driver is corrupted, or if I should just use ndiswrapper with the windows drivers. Obviously, I would prefer to use native linux drivers, but the wrapper will not tax the system too much if I use that option. I have heard that these laptops are very linux friendly, and I ran xubuntu on it for quite some time with no big problems. My home router is a Belkin F6D4230-4 V3. This thing will not show up at all, but my family's old linksys will, I can't connect to it either.

View 7 Replies View Related

General :: Hp 3050 Wireless Printer Don't Print From Puppy 5.1

Jul 24, 2011

I got a hp 3050J610 wireless all in one and hooked it up to my wireless network
and it works fine from windows vista from my hp notebook. I also run puppy 5.1
off a pen drive which runs fine on the laptop. Puppy sees my network fine and
goes on the internet from my satalite modem over the wireless network no problems.
I installed the wireless printer to puppy with the cups wizard without any errors or problems. Cups found the printer and correct ip address no problem. I used the 610c driver from the cups menu which I assume is the right one. I can't seem to find another one. It lists the printer and lists the right ip address. when I try to print it shows it is printing the print job but nothing happens at the printer. I look in the print manager and it shows the print job was done. I can ping the ip address and get a responce.

View 3 Replies View Related

General :: Puppy System Requirements (recommended) For Runescape On A Live USB?

May 20, 2010

I am wondering if you can play Runescape on Puppy Linux(Slackware) with Java, Flash, and the plug-ins are all installed, and i use a Live Usb. Is this possible? Recommended Requirements(and please don't write the bare minimum)

View 3 Replies View Related

OpenSUSE Network :: Configure ZTE AC2726 USB EVDO Modem 11.3

Nov 20, 2010

I am trying to access the internet via my ZTE AC2726 USB EVDO Modem in openSuSE Linux 11.3.

I have looked at the site How to configure ZTE AC2726 USB EVDO Modem on openSuSE Linux | bayuirawan.com but when I type the command:

As below,the following errors appear:

View 2 Replies View Related

Ubuntu Networking :: Setup ZTE CDMA 2000 IX EVDO Bsnl Wireless Terminal?

May 11, 2010

I started using linux ubuntu version9.04 2 days ago...And I am facing difficulties in configuring or using my bsnl ZTE CDMA 2000 IX EV-DO wireless data terminal in ubuntu... I can't install gnome-ppp on my system... installing it in offline mode. Also,I tried the following commands:

$ sudo aptitude update
$ sudo aptitude install wvdial gnome-ppp
# lsusb
#modprobe usbserial vendor=0x19d2 product=0xfffe $ sudo nano -w /etc/wvdial.conf

I made the following changes in my wvdial.conf file,

[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Stupid Mode = 1

[code]...

I am getting an error message as:

Wvdial configuration 1.60
/dev/modem: command not found
/dev/modem: command not found
/dev/modem: command not found

View 1 Replies View Related

Fedora :: How Are Using BSNL EVDO Data Card - First Click On Application - System Tools

Oct 22, 2010

I found lots of pepole who belongs to India and using BSNL Data card wants to connect Internet from fedora so I thought post a thread which will help all how are using BSNL EVDO Data Card. At first click on application - System Tools - Terminal enter the following code on your terminal

Updated part starts here When I was using Fedora 10 I post this thread on that time gedit worked properly with "su" Now here if you are using Fedora 14 and by using su gedit is not appearing then try

Code:
su -
instaed of only "su" hope gedit will work properly. If dose not work then you can follow the next post instructions. Or you can ask in the forum for I am updating "su" by "su -" If you are using earlier version you can try by only "su" or "su-" if none of this works then follow next post. Just remember you have do this in a single terminal and step by step to avoid maximum uses of "su" or "su -"

[Code]...

View 2 Replies View Related

General :: Configured System To Connect To A Wireless Network On Bootup?

Mar 16, 2011

I have configured my system to connect to a wireless network on bootup, but now every time I boot I have to wait and watch it connect (it outputs some dhcp connect stuff) which delays the boot process. is there any way to just initialize the script and then go on with the boot process instead of letting it output some pointless crap and waiting for it to end?

View 5 Replies View Related

General :: Datacard Goes Online But Doesn't Gives Internet Access (Fedora 14)

Dec 25, 2010

I am using MTS datacard. I have usb_modeswitch installed and have configured the wvdial.conf file. When I do sudo wvdial cdma, the IPs and DNS addresses are also allocated but I still cant access internet.
The reply to dmesg | grep -e 'tty' -e 'modem' is:

[Code]...

View 1 Replies View Related

Installation :: When Installing Puppy - Get Stuck After Searching For Puppy Files

Jun 21, 2009

I am new to Linux and I am trying to install puppy on an old IBM thinkpad 600X (10gb hd, 196mb ram) When installing puppy from a cd, it loads up and does the kernel stuff before "Searching for Puppy files in computer disk drives" - this takes about 10 minutes before saying "pup_421.sfs not found. Dropping out to initial ramdisk console" then it goes to "/bin/sh can't access tty; jon control turned off". then it stays like that and doesn't continue.

View 8 Replies View Related

Networking :: Realtek Rtl8192u Driver Locks Up System (Puppy 4.3.0, Fresh Install)?

Jan 20, 2010

I've got a Puppy system running version 4.3.0 that I'm trying to get on the home network. I'm using a D-Link DWA-130 (H/W revision C), which has a Realtek RTL8192U chipset. I got the drivers off of D-Link's website, and they compiled and installed just fine, but when either a) I try to connect to the network, or b) while I'm browsing the web, the system locks up completely. No mouse, no keyboard, no Ctrl-Alt-Bksp to get out of X, nothing.

I'll outline my steps: Install Puppy using a "Full" HDD install (not "Frugal"). Copy the "devx_430.sfs" file (which I got from the Puppy website) from a thumb drive to the "my-documents" folder (although the exact location proabably doesn't matter). Mount it, cd to the mounted directory and execute "cp -a --remove-destination ./* /" and "sync". Copy the kernel source for 2.6.30.5 ("kernel_src-2.6.30.5-patched.sfs4.sfs") to the same directory. Mount it and execute the same commands as before. Copy the folder containing the RTL8192U drivers ("rtl8192u_linux_2.6.0006.1031.2008") to the root directory (i.e. "/"). cd to the folder in the terminal and run "make", "make install".Reboot the machine. Set up networking using the Puppy Internet Connection Wizard. HERE'S WHERE IT SCREWS UP: It connects, but after a while (e.g. just after logging into LQ through it, as a test) it freezes the entire system.

I have to do a hard reboot ("panic button"), then a soft reboot (for some odd reason the usb module won't load after a hard reboot, so the mouse won't work) to get the system working again, only to have it lock up again once it connects to the network.

Are these drivers broken? Outdated? Is there anything I can do to fix this? EDIT: I should add that this only occurs when the adapter is plugged in. If I boot the system with it unplugged, it works fine (probably because it never loads the kernel module).

View 11 Replies View Related

Fedora Networking :: 12 - Can't Connect System To Wireless Network

Feb 9, 2010

I'm running the 64-bit version of Fedora 12 on a MacBookPro5,1 system. I am unable to connect to my wireless network, which shows up in the list of available wireless networks.

I will enter my password and the system will try for several seconds to establish a connection and then fail.

I know the network is fine because I can connect to it when I boot the computer in Mac OS X.

What can I try that will allow me to connect to my wireless network under Linux?

View 1 Replies View Related

Networking :: Can't Connect Fedora 12 System To Wireless Network

Feb 8, 2010

I'm running the 64-bit version of Fedora 12 on a MacBookPro5,1 system.

I am unable to connect to my wireless network, which shows up in the list of available wireless networks.

I will enter my password and the system will try for several seconds to establish a connection and then fail.

I know the network is fine because I can connect to it when I boot the computer in Mac OS X.

What can I try that will allow me to connect to my wireless network under Linux?

View 4 Replies View Related

Fedora Networking :: F12: Broadcom Wireless Does Not Detect Any Network On X86_64 System

Dec 8, 2009

I have a Broadcom Corporation BCM4312 802.11b/g (rev 01) wireless card. I installed these packages:

broadcom-wl-5.10.91.9.3-1.fc12.noarch
akmod-wl-5.10.91.9.3-3.fc12.6.x86_64
kmod-wl-2.6.31.6-145.fc12.x86_64-5.10.91.9.3-3.fc12.8.x86_64

[code]....

uname -a says:

Linux boz.alafkhar 2.6.31.6-145.fc12.x86_64 #1 SMP Sat Nov 21 15:57:45 EST 2009 x86_64 x86_64 x86_64 GNU/Linux

and:

# lsmod | grep wl
wl 1278432 0
lib80211 6436 2 lib80211_crypt_tkip,wl

[code]....

My networkmanager understands that the card is installed. But it can not find any network. Also iwlist scan gives me no result. I did not have this problem on earlier fedora releases. Recently I upgraded to F12 from F11. I should mention that I have another USB DLink wireless card and when I plug it, everything works fine with that card. I also tested wl_apsta driver using fw-cutter. I did not work neither.

View 6 Replies View Related

Fedora Networking :: Wireless Configuration Does Not Show Up In System-config-network

Sep 1, 2010

This may fall under the "ain't broke don't fix it" category but it's driving me nuts. I've got the Broadcom 4322 wireless adapter in my laptop and it works fine with broadcom-wl driver and kmod. However there is no ifcfg-eth1 file and the card does not show up in system-config-network.

View 2 Replies View Related

OpenSUSE Wireless :: Wifi Card Can't Connect On Network After System Hibernate?

Sep 15, 2011

wifi card:atheros ar5007egOS: openSUSE11.4My laptop can't connect on network after system hibernate. It has been asking me for enter the wifi password. But when I input the wifi password it still can't connect on network. I have to reboot it.

View 3 Replies View Related

OpenSUSE Install :: Use Vodafone Datacard On Suse 11.1?

Feb 7, 2010

how to use vodafone datacard on suse 11.1?

View 4 Replies View Related

OpenSUSE Network :: Linksys Wireless WMP600N - Error Suse 11.2 - System Freezes

Feb 13, 2010

I bought the wireless PCI network card WMP600N from Linksys. I tried to connect with my router, but no success. The correct driver is installed(RT2800), the necessary package WPA_supplement is also installed. My providers settings are WPA-PSK with a shared key. Key encryption is TKIP. I can't choose TKIP in the Yast network menu. so i chose passphrase.

the weird thing is that the wifimanager says WEP is on but it's not, at least not in my router and i did not setup WEP to. see picture 6. i had to use manual boot "ifup wlan0" because when i use boot at startup the whole systeem freezes. anyway, when i use ifup wlan0 as root in the konsole, the system also freezes. i have explained it clearly, please take a look a the pictures.

step1
step2
step3

step4 After pressing enter the system freezes.

View 9 Replies View Related

Networking :: Unable To Configure Wireless Network On Dell Laptop And Oracle System / Fix It?

May 26, 2010

I am a first time Linux user - though I've Unix and Windows experience. So though I can follow your most tech instructions, I'll need some hand-holding.

Need help getting my wireless network to work on my newly installed Oracle Linux on Dell laptop.

Not sure what wireless card is installed, or it's mac address (though I can boot into windows and get that info, I don't want to - it'll be kind of a let down if I can't fix it all thru Linux).

Install has detected a Broadcom wired card, but not the wireless. Funny thing is that it detected the Bluetooth.

View 3 Replies View Related

General :: Way To Prevent Network Manager From Storing Password For Wireless Network

Sep 27, 2010

Our corporate wireless network uses continuously changing passwords with RSA tokens.So every time we need to connect to the wireless we need to enter a new password off the RSA token. For extra fun using the wrong password a couple of times in a row causes the users account to be locked.Network manager automatically stores and reuses the password, with the net result that it is constant getting my account locked.Is there some way to prevent it from storing my password for that network?

View 1 Replies View Related

Ubuntu Networking :: Unable To Connect BSNL 3G USB Datacard In 11.04?

May 7, 2011

Ubuntu 11.04 isn't detecting BSNL 3G USB Datacard. I was using 10.04 earlier & could easily install it then. But now 11.04 isn't detecting the USB datacard, so I'm unable to connect to internet for updates

View 9 Replies View Related

Networking :: Cant Connect To Internet Via Tata Indicom Datacard

Oct 7, 2010

I am using redhat linux os rhel 5.3. i am not able to connect to internet via my new tata indicom datacard in this operating system...how can i configure it to work...i am using vmware to run this operating system...

View 2 Replies View Related

Fedora :: My Wireless Isn't Working - Network Configuration On System-administration The Interface It Appears As Inactive

Dec 10, 2009

I have b43 wireless. In network Configuration on system->administration the interface it appears as inactive it appers in hardware also as b43 associated to wlan0 but i cannot have access to any wireless network. What i have to do to put this b43 to work.

View 11 Replies View Related

Ubuntu Installation :: In Windows 7 (64 Bits) File System Installer - Cannot Detect Wireless Network

Nov 28, 2010

Ubuntu in Windows 7 (64 bits) File system installed using Wubi I got Ubuntu 10.04 LTS intalled using Wubi. That means Ubuntu resides inside Windows file / folder system. It also means Ubuntu does not have its own partition. Here is what I found out:

1) It cannot detect wireless network unlike Win 7 on this same laptop. However, when I plug in ethernet cable, it was able to detect it. Is there a fix this problem?

2) I cannot see Windows folders. How do access windows folder from Ubuntu side and vice versa?

3) I forgot to set the disk space for Ubuntu during install and I think the default is 17 GB.Would this cause me problems? If so, what do I need to do? How do I expand the disk space for Ubuntu?

View 1 Replies View Related

OpenSUSE Wireless :: When Click The Button To Connect To A Wireless Network This Message Apears:Network Management Disabled?

Mar 23, 2010

When i click the button to connect to a wireless network this message apears:Network management disabled

View 1 Replies View Related

Networking :: Datacard Goes Online But Doesn't Gives Internet Access (Fedora 14)

Dec 25, 2010

I am using MTS datacard. I have usb_modeswitch installed and have configured the wvdial.conf file. When I do sudo wvdial cdma, the IPs and DNS addresses are also allocated but I still cant access internet.

Code:

dmesg | grep -e 'tty' -e 'modem'

is:

Code:

[ 0.000000] console [tty0] enabled
[ 11.098238] USB Serial support registered for GSM modem (1-port)
[ 11.098352] option 6-1:1.0: GSM modem (1-port) converter detected

[code]....

View 1 Replies View Related

General :: Download Puppy 5.2 - Than Put It On A Dvd ?

Feb 22, 2011

How would I download puppy linux 5.2, then put it on a dvd.

View 2 Replies View Related

General :: More 15 Partition In Puppy ?

Apr 27, 2011

I have installed on sda16 but not see in puppy with pmount why?

View 1 Replies View Related

General :: Can't Get Puppy 4.3.1 To Work Right On E-Bay?

Oct 15, 2010

I can't get Puppy 4.3.1 to work right on E-Bay. some info is missing on sale page....anybody been able to post ad?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved