I am trying to access the internet via my ZTE AC2726 USB EVDO Modem in openSuSE Linux 11.3.
I have looked at the site How to configure ZTE AC2726 USB EVDO Modem on openSuSE Linux | bayuirawan.com but when I type the command:
As below,the following errors appear:
I have never connected to the internet using ZTE EVDO modem. I know it's being recognized but connection cannot be made.
View 9 Replies View RelatedI have bought a new USB modem from my service provider. The model they provided is "Huawei EC1260" Huawei Terminal. As usual the official support is for windows and mac.
I tried to install this device using two methods..
1) Set knetworkmanager settings to "traditional with ifup". Then in wireless setup there is a choice of having "usb" (A tick box). I selected that, and setup completed successfully but the knetworkmanager was not up(I did ifdown wlan0 (wlan0 was the wireless config name), ifup wlan0 and the rcnetwork restart.)
2) Again knetworkmanager was set to "traditional method with ifup. This times while adding the connection I specifically selected the type "USB", then clicked to finish the configuration. The configuration finished without any errors but when I checked the Network Configuration screen no USB device was added there.
Are there any specific steps to configure a USB modem
I have a Zoom 2920 internal hardware modem that worked well with Suse 10.0. In Suse 11.3 the modem config. overview lists 2 modems for this one board; #1- AT Modem and #2- Venus Modem (v90, 56K Flex). With #1 "edit" brings up modem parameters and the modem device line is blank. With #2 the device line shows /dev/ttys4.
When the provider parameters are entered, for either #1 or #2, the modem overview continues to list them as not configured but a third line "modem 0" is configured with the provider information at /dev/ttys4. The modem will not function.
What include support a driver for USB modem Huawei E219 (HSDPA/UMTS) and Huawei EC226 (3G/EVDO)?
View 1 Replies View RelatedMy EVDO (Mass storage cum Modem device) like USB Modems not working on Linux-2.6.10 kernel.I used usb_modeswitch-1.0.5.tar.bz2 package on Linux to flip from mass storage device to modem
View 3 Replies View Relatedhow should i install the EVDO modem in rhel 5.3?
View 1 Replies View RelatedI'm running Ubuntu 10.04 in South Africa and I am using a Neotel telephone device that connects with EVDO. I have followed instructions to get it working by typing: sudo modprobe usbserial vendor=0x1d09 product=0x4000.
I have also put it in /etc/init.d/rc.local to get it to load up on startup. This works and I am able to connect using the network manager. The problem is if I disconnect and then try to connect again later, it refuses to connect till I reboot and then it works, till I disconnect again.
I am planning to shift from ubuntu to fedora and i am using Data card for getting connected to internet. My data card is working fine with Ubuntu 10.04.
I have been using usbmodeswitch to make the device to be reconized as a modem rather that a storage devices in ubuntu 10.04. i have followed this link : [url] and it worked fine now when i repeated the same for fedora 13 it doesn't works.
I have installed tcl-8.5.8-1.fc13.i686.rpm , usb_modeswitch-1.1.4-1.fc13.i686 , usb_modeswitch-data-20100707-1.fc13.noarch and wvdial. in fedora 13 it never detected as a modem. i have also tryed using # modprobe usbserial vendor=0x1c9e product=0x9e00 also but this never helped.
I have been using an ethernet ADSL Westell modem for years and would like to upgrade to a newish Allied Telesyn USB Modem AT-AR206 in Fedora Core 10. The modem power goes on when plugged into my pc and lsusb shows that it has been recognized with this:
Bus 002 Device 003: ID 1110:9022 Analog Devices Canada, Ltd (Allied Telesyn) ADSL Loader
I used system-config-network but don't have the option of adding this new hardware.
How do I configure my network to use my DSL line?
I've recently come into possession of this modem which is supposed to be supported in linux kernels but I'm not sure how to set it up or detect where it is located (dev/ttxx)
View 5 Replies View RelatedI'm new to opensuse as well linux.today i installed suse 11.3 and installation completed.then i plug the usb modem (ZTE mf 100) and then nothing appears..i dont know what to do for configure the modem.
View 2 Replies View Relatedi have been able to get on line running other linux os using the terminal first i type sudo modprobe -r usbserial & enter followed by sudo modprobe usbserial vendor=0x1199 product=0x120 & enter the last command is sudo dmesg|grep -i ttyusb. I have done this for years and it always has got me on line after the above i open kppp and select for modem /dev/ttyusb0 and click to verify kppp recognizes my sierra wireless usb modem and that is all i have ever had to do, plug in the usb modem type the three commands it comes back with confirmation the modem is attached to ttyusb0, ttyusb1 & ttyusb2 in kppp i click /dev/ttyusb0 and click quarry and get on line with suse11.1 it is not so the first command sudo modprobe -r usbserial comes back with a fatal error but the second and third command give me the same results saying i have attached the usbmodem to ttyusb0,1 & 2. but i cannot configure it in kppp.
i have tried researching on line but cannot find a similar thread. I believe the way i described above has worked on lindows 5.0, and it is how i do it with Mint which i can get on line with today. so i hope one of the wonderful millions of linux users will direct me as to what i am doing wrong. i am running amd 785 4 gb ram msi mainboard ms-7549 my modem is sierra wierless modem 595u (vendor=0x1199 product=0x120) connecting through Sprint pcs which requires no user name or password.
I have recently downloaded live cd of Puppy Linux and boot successfully from it. But, I could not connect my BSNL EV-DO datacard as no wireless network connection is detected by Puppy. What should I do? How can I configure my BSNL EVDO Datacard over Pupply Linux? Plz.
View 1 Replies View Relatedtrying to make my 3G modem (a ZTE MF622) work with OpenSUSE 11.2. KNetworkManager is recognizing it (so I suppose it's not on Storage Mode), I can create the 3G connection and connect, but I can't navigate on any sites (ping gives "unknown host" for any IP). Also, the KNetworkManager applet doesn't show anything on fields "Name servers" and "Domains" (they are blank). Tried some instructions from the internet here and there, but didn't have any luck.
View 9 Replies View Relatedi'm running suse 11.2 and using a ZTE mf627. thus far i can connect to the internet using usb_switcher/vwdial but i want to share it across a LAN. all the how-to's on connection sharing I've seen use the network manager/network settings, but the device doesn't show up in either
View 2 Replies View RelatedI'm trying a long time to configure my 3g modem to connect.I had tryied using the KDE Network manager and the modem stay in "Waiting authorization" for ever ^^.The KDE Network manager runs ok in Kubuntu.I had tryied download and install kppp, but kppp don't open my modem (/dev/ttyUSB01)Then how can I configure my modem?
View 1 Replies View RelatedI have a devolo MicroLink 56k Fun LAN modem, which I could configure in openSuse 11.2 as an DSL device. With 11.2 it worked fine. But it isn't possible in 11.3 to configure it, because I cannot set the dial up internet provider phone number for this DSL device.I also tried it to configure it as a modem, but then it used the /dev/modem device, which is the wrong device for this LAN modem.
View 3 Replies View RelatedI have a box with 1 ethernet card and Huawei E160 USB modem. So, I have configured eth0 interface with IP 192.168.1.1 and modem0 interface with dynamically assigned IP. Now, I'd like to share Internet from modem0 to eth0 and so to the rest of home local network.
I need your advice on how to do it. All the manuals I've read deal with two ethernet cards that have static IPs. It seems that YAST lacks the GUI for it, too. Also, I need the configuration to work even with no user logged in so I'm using ifup instead of NetworkManager.
I am using 11.4 gnome desktop on hp elitebook 8440w. I have a reliance netconnect plus usb modem. (ZTE AC 2726).
Initially it was recognized but didn't work. But now system is not recognizing it. What should i do. Please suggest.
Im new in this world of linux and suse. I have just installed the opensuse 11.2 in a Dell Inspiron 5160. Such laptop has a BCM4306 Wireless LAN controller. When I tried to configure a wlan connection, I found that the firmware was not installed. After looking in different forums, I installed the firmware b43. Now, my wlan card is abled to find the wireless of my router.
I have tried to configure a connection with YAST as well as with Network Manager, but both cases failled. Specifically, when I use Network manager, Im able to see in the applet my connection, how strong is the signal, but I see a yellow symbol (in one forum, such a box is shown with a green symbol).
I have check many time all about the secutity, encryption, and so one and all seems to be correct. But when I open the mozila firefox or the konqueror browser, no chance to surffer in internet. Now Im just a step to become crazy. The drivers are ok, the information about the router and the keys are ok, but in such a way, I am still harmloss.
I have just installed opensuse 11.3. I am absolutely new for Linux and for this forum. I have tried to open Network manager to configure my wlan. But its not starting. How to start network manager and configuring my wlan.
View 4 Replies View RelatedI'm going to come right out and say I am a complete novice with Linux/SUSE. The equipment I'm having a problem with is a little web-server that was purchased by my employer that has, quite suddenly, stopped functioning. I was changing the IP address within YaST, at which point the device offered to update itself, which I saw no harm in. Post-update, however, I was unable to so much as ping the device.
I tried "ifconfig eth0": "Error fetching interface information: Device not found." I went into network settings via YaST and found that there are two cards now listed as: RTL8111/8168B PCI Express Gigabit Ethernet controller Both IP addresses are "Not configured". The information pane, for both cards, cites:
RTL8111/8168B PCI Express Gigabit Ethernet controllerBusID : 0000:02:00.0 Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details. The only difference in either of the cards is the BusID (0000:02:00.0 and 0000:03.00.0)
I can neither edit nor delete either of these cards. As I mentioned, I am a total Linux novice, and am at a total loss for what to do next, or even how to find critical information about the system itself. I know enough to check dmesg, but not enough to have any clue what to look for in the output.
I am running a 3-G wireless USB broadband modem, and connecting with Network Manager, but I keep getting disconnected when idle after 5-6 minutes. I am used to using Kinternet to connect with my 3-G wireless USB broadband modem, and setting it up in Yast / Network / Modems, but was not able to configure my modem there (for some mysterious reason) so ended up using Network Manager instead.
What's going on here regarding YAST being unable to configure my modem (even when Network Manger is disabled). But my main problem at this point is that my connection times out after about 6 minutes if I'm idle. This is a big problem for me because I type slow and frequently get disconnected while posting on message boards. Where are the idle time out settings are for Network Manager? I can't seem to find them.
I just loaded 11.2 & Kde 4.3. Installed both Kinternet and Kppp. My modem is a USR PCI HW modem 2976. Hardware Info shows it connected to /dev/ttyS4. I configured the modem with Yast as modem0. The user access box is checked for Kinternet Both Kppp and and Kinternet will dial out.
The connect response comes back from the ISP and either of the dialers will hang and the dial tone comes back. The firewall is showing modem0 in the External section. Nothing changes if I shut the firewall off.There's nothing in the dmesg I could find. Could this be a pppd permission problem?
My machine is running on a dual-boot Windows Vista/openSUSE 11.2 scenario. I have been trying to get my Huawei E1550 to work on Linux for the past few days trying numerous methods suggested in other forums from people with the same problem, but I have not produced any fruitful results.
Plugging in the USB modem results in Linux detecting it as a CD-ROM. I have installed usb_modeswitch in attempt to switch it to a modem, but Linux still fails to recognize it. Windows Device Manager and lsusb both give ProductID=1001 and VendorID=12d1 connected to USB1. I'm guessing since Windows detects the correct IDs, the Linux versions should also be correct. In any case, I ran usb_modeswitch with the Default IDs for /etc/usb_modeswitch.conf, which gave 0x1446 as the ProductID, not 0x1001. Upon running usb_modeswitch, the product ID could not be found so the program fails and quits asking if it's connected (and it is).
Just to test, I also ran wvdial which unsurprisingly did not detect the modem and could not send the init strings. All commands were done using root privileges. Also note that when after usb_modeswitch is run and upon plugging in the USB, NetworkManager pops up near the tray saying "attached" but still shows the device as a CD-ROM.
I have an external usb dial up modem. lsusb shows: Bus 001 Device 002: ID 2001:f10d D-Link Corp. [hex] Accent Communications Modem How do I set this up? It probably needs a driver, how do I check it, or better yet, can I get yast to tell me if it recognizes the modem or needs firmware? I know linux and dial up is like the seventh circle of hell. Just wondering if there was a snowball's chances of getting this working. Sorry if this is the wrong section to ask in. Seemed like as good as any when I checked.
View 9 Replies View RelatedI have a US Robotics serial modem, and I have smpppd enabled in system services, with wvdial and kppp installed. When I try to set the modem up using yast, I keep getting hung up by the different screens. First a screen that asks if I need to dial a number to get out. I have to dial 9, so I have that entered. Then a screen that asks for "country" and "provider."
When I try to enter anything, nothing shows in the boxes, so I go to a screen that asks for the phone number, provider, user name and password. When I enter those, it goes to a screen that wants "Connection Parameters", with default settings and the "buttons" at the bottom of the screen "muted," or flattened out, i.e. unusable. That makes it impossible for me to set the information as saved, so it's back to the beginning and sart over, with the same results over and over. How do I get the modem so it dials out?
I got a new cable modem so I could get rid of the one I've been leasing from the cable company. It is a Motorola sb6120. Everything is fine with the ISP, it's approved for operation on their network, the only hitch was I had to use my Windows laptop to run their activation software.
At any rate, with the new modem installed, I hop on my Linux box and go to work. I'm seeing some terrible delays in looking up names. When I look with firebug, all the dns lookups for new names are taking 15+ seconds. First I just think maybe the names aren't cached or something is weird for a minute and it will get better, but no. After several restarts and then a couple days persevering with the new cable modem, all DNS queries are still terribly slow (including zypper, mail client, web client).
Suddenly I remember an issue I was having with, I believe version 11.1 when I first installed it. For just the computer on my network with a fixed IP address, DNS resolution was slow like this and if I disabled IPv6 then all was well. I believe there was even a patch issued back then for gethostbyname() that was supposed to fix the issue? So, when I disable IPv6, DNS lookup is back to normal. The two Linux computers on my network had been working fine with IPv6 and the old modem, though, and the Windows box is still working fine even with the new modem.
I can disable IPv6 and make it fast again, but really why should I have to?
If I connect with a 3g modem or with wireless sometimes the resolving does not work. This happens on opensuse 11.2. nslookup and dig works but nor ping nor ssh nor any other network application does work If I modify the /etc/resolv.conf after connecting to a wireless network for example it does not work even the dns are known And more strange if the resolver works and I modify /etc/resolv.conf with known dns the resolver does not work anymore. BTW: the dns entry from the wireless is 192.168.1.1 and I do not have any idea how the wireless ap is configured... so it could be in this case that dns is not forwared only allowed to use 192.168.1.1 but the other case is a 3g modem which not even the propagated dns entries works in the bad case
View 9 Replies View Related