OpenSUSE Network :: Internet Datacard Gets Disconnected After Sometime?
May 21, 2011
If i leave my laptop idle for sometime, my usb datacard connection gets disconnected. I know its a dial-up connection and if no application is accessing internet it disconnects on its own. The problem over here is when i click on the icon and click on activate it won't happen. So, i have to unplug the hardware and then re-insert it to make it work again.I went through a site, there they have mentioned a work around that is to keep a ping command always running. I'm fine with that, but why do we need to remove the hardware n re-insert it to make it connect to the internet again
View 3 Replies
ADVERTISEMENT
Sep 29, 2010
I got problem in my internet every time when system is boot or network is disconnected i have to enter the DNS address(number) primary and secondary
View 7 Replies
View Related
May 2, 2010
My friend has 2 pcs, one connected to the internet and the other one used to connect (when he had windows installed) to the internet through the first one using internet sharing, now i installed ubuntu on both and the network between them has been created but it wont connect, the internet icons just animates for like a minute then says "wired internet disconnected" in other words it failed to connect.
View 1 Replies
View Related
Oct 7, 2010
I am using redhat linux os rhel 5.3. i am not able to connect to internet via my new tata indicom datacard in this operating system...how can i configure it to work...i am using vmware to run this operating system...
View 2 Replies
View Related
Dec 25, 2010
I am using MTS datacard. I have usb_modeswitch installed and have configured the wvdial.conf file. When I do sudo wvdial cdma, the IPs and DNS addresses are also allocated but I still cant access internet.
The reply to dmesg | grep -e 'tty' -e 'modem' is:
[Code]...
View 1 Replies
View Related
Dec 25, 2010
I am using MTS datacard. I have usb_modeswitch installed and have configured the wvdial.conf file. When I do sudo wvdial cdma, the IPs and DNS addresses are also allocated but I still cant access internet.
Code:
dmesg | grep -e 'tty' -e 'modem'
is:
Code:
[ 0.000000] console [tty0] enabled
[ 11.098238] USB Serial support registered for GSM modem (1-port)
[ 11.098352] option 6-1:1.0: GSM modem (1-port) converter detected
[code]....
View 1 Replies
View Related
Jan 31, 2010
Since 11.2, I am using Knetworkmanager for getting connected to the internet.But is getting disconnected on its own every now and then. I used Kinternet when I was on 11.1 and it worked fine, Infact I would prefer kinternet over knetworkmanager anyday. But in suse 11.2, having both KDE3 and KDE4 libraries does make system work unexpectdly. I tried installing Kinternet once but after that kontact kept crashing (because of clashes between kdelibs3 and kdelibs4).Can anyone help me finding out the problem in knetworkmanger.. here is entry in /var/log/NetworkManager when I got disconnected..
Code:
Jan 31 14:38:27 linux-9psh NetworkManager: <info> (ttyUSB0): device state change: 8 -> 7 (reason
[code]...
View 1 Replies
View Related
Aug 29, 2011
I have OpenSuse 11.3 with VirtualBox on it, and with installed Oracle DB (on host OS).. but, sometimes this computer is disconnected, without it's gateway (adsl router)... and in that case, I cannot ping from virtual OS to host OS, or another virtual OS. I tried to use 'Host only' option within VirtualBox, but it doesn't work. What should I do? It seems that virtual machines requires some kind of gateway/router, but since machine is disconnected, it's not working.. how could I fix it?
View 4 Replies
View Related
Jan 21, 2011
I have recently downloaded live cd of Puppy Linux and boot successfully from it. But, I could not connect my BSNL EV-DO datacard as no wireless network connection is detected by Puppy. What should I do? How can I configure my BSNL EVDO Datacard over Pupply Linux? Plz.
View 1 Replies
View Related
Feb 7, 2010
how to use vodafone datacard on suse 11.1?
View 4 Replies
View Related
Jun 7, 2010
My Ubuntu web server is left on all the time, sometimes I notice that it is disconnected from the network so I have to goto the server and re-enter the password in the network connections, this allows me back onto the network. Why is the server being disconnected? (The computer is running all the time because if it re-starts the terminal window is open on the screen). And how can I stop it from happening? It's got to the point where I need to check it every hour which really defeats the purpose of having it!
View 1 Replies
View Related
Dec 3, 2010
Is there anyway I could use KISMET without getting disconnected from a network. I mean now whenever I start kismet, I lose my network connectivity. I dont want that. is there any possible workaround for this?
View 3 Replies
View Related
Jan 28, 2009
I'm using Xubuntu and i have set up my DSL connection manually. I get disconnected from the Internet within 2-3 minutes. I have to again select eth0 from the network icon in the taskbar. it connects well but gets disconnected again and again. I don't face such problem when i use Win XP.
Any idea what might have gone wrong ?
View 4 Replies
View Related
Jul 5, 2011
OpenSuse 11.4 Asus Netbook 1000H Following other members in the forums I have installed Opensuse 11.4 on the Netbook. In the early days Ubuntu Netbook Remix worked well for me. But this has been discarded, and the "one size fits all" Ubuntu had become slow and cumbersome. So..... onto my post. Opensuse is working well. The install went beautifully.
It detected the Wireless Internet and I am able to get on line. I also need to share the Internet connection to a desktop. This is done via a small network switch. Thus far I cannot do this. I tried to use ifup to configure a static ip but this busted my Wireless configuration. I went back to knetwork manager. Then I tried to set up the wired network using knetwork manager and under IPV4 "share" the connection. But this blanks out any possiblity of a static address and substitutes dhcp. My desktop cannot ping the this dhcp address. Ubuntu had this thing called Firestarter? - from memory. This configured the system to sharing the network.
View 7 Replies
View Related
Feb 14, 2010
I recently installed Ubuntu. I just installed ndiswrapper so I could install my wireless PCI [COLOR=blue ! important][COLOR=blue ! important]card [COLOR=blue ! important]drivers[/COLOR][/COLOR][/COLOR]
I did that and it is recognized and so is the network I want to connect to. But for some reason, it just wont connect. It will spend a long time trying to connect, but then just says "disconnected". It's not like I have a bad connection or anything. My internet on Windows is fast.
View 3 Replies
View Related
Jul 10, 2010
Our area was hit by a power surge and I cannot get the internet connection to work? What can I do. I'm using an AT&T modem which is connected to a netgear router.
View 4 Replies
View Related
Dec 30, 2010
I recently updated my ubuntu to the newest version 10. I have a DSL router with a password. When I try to connect to the net it will try to connect for about 5 or so min then say that I am disconnected. I cannot remember what option I had before to connect but its not on this version.
View 4 Replies
View Related
Apr 12, 2010
I installed Suse 11.2 on clean HD. I cannot connect to the internet. Seems like Suse didn't install drivers for on board ethernet card. It is a Marvell Yukon 88E8056. I'm new to this and don't know how to install the drivers.
View 3 Replies
View Related
Sep 10, 2011
I have SUSE 11.0 set up to act as a router/firewall for my home network to the internet through a cable modem attached to an Ethernet card. When I was laid off several years back, I found information that let me connect my network to an ISP via a standard serial modem. I am considering going to the Sprint U1901 4G USB modem and dropping cable internet. Sprint claims the U1901 is Linux compatible. My thoughts are that using the 4G modem should be similar to the old dialup modem. I had a script that connected to the internet whenever internet traffic was detected. Unfortunately, I did not save notes on what I had done to setup the modem to dial automatically, and I have been unable to locate information that seems good to set this up again. I already know that all I had to do to get routing working was simply replace the internet port in the firewall/routing script with the port for the modem. So I assume that is rather trivial.
Would you please point me to a doc, perhaps SuSE specific, that gives reasonable directions on how to set up a "dial on demand" ISP connection? I assume that the 4G modem will be very similar to my old serial modem so that a dial on demand script will work. I did find a dial on demand howto, however, it did not seem to apply.
View 3 Replies
View Related
Feb 9, 2011
This is not the common problem that's on the stickied thread. I'm able to connect to my wireless network perfectly. I switch between Windows to game and Linux for desktop, coding, and hosting, so I can tell it has something to do with ubuntu 10.10. When I'm connected to my wireless network, at random times, my internet begins to slowdown, then I get disconnected from the internet, but the taskbar says I'm connected. This problem only happens in ubuntu and not Windows for some strange reason.
The applications that are usually open do not cause it, because it still does it even though I have little applications open (Google Chrome, gedit). When I'm on Teamspeak 3, I notice my ping rises to the 1000s randomly, and I get disconnected. Once again that only happens on Ubuntu.
View 6 Replies
View Related
Jun 25, 2010
In short: browsing the internet with domain names does not work. The long version: I've configured my network with DHCP and ifup. Ping works on my internal net and with servers in the internet. Dig work's too! I get the right IP to the requested domain. When i try to access the internet using firefox or even wget i get an DNS error. For example wget is showing the following error: Resolving heise.de... failed: Name or service not known. wget: unable to resolve host address 'heise.de'
Again dig show me the right IP and if i add the entry to /etc/hosts it work's too! I've even tried it with manually setup of ip address, nameserver and default gateway but with the same result. Switching off the firewall has no effect on this problem, too.
View 9 Replies
View Related
Jul 11, 2010
Look Buddies,an interesting issue.
Once i just remove X11 libraries , gdm , gnome libraries and network-manager applet. from the ubuntu 9.10.
after these uninstallations, i used my internet successfully through text interface browsers which is links
but i understood graphical interface are important for my work.
Once again i installed
1. xfce4
2. network-manager applet
Everything Graphics,X11 sessions and accessing internet is working fine.
i can even browse through Mozilla firefox.
But my Network-Manager applet is always show as disconnected in taskbar. I understood some kind of understanding between network -configuration files and network-manager applet are broken
Why is the Network-Manager Applet is not responding?
View 1 Replies
View Related
Jan 5, 2011
I install from openSUSE-11.3-NET-x86_64.iso. Installation was succesfull, but after install all packet on test internet / update was error. And after log in in installed system internet not work. I use router with DHCP
View 8 Replies
View Related
Feb 25, 2011
I'm on opensuse 11.4 (11.3 won't work with my monitor).
My computer gets internet through wireless and I want to share that internet through its ethernet port. So far I've tried using Knetworkmanager to create a network bridge between my wireless and wired connections. I created a new wired connection and shared it using the ip address settings. I was able to get both connections active, but the device hooked up via ethernet had no internet connectivity.
I also tried this command:
echo 1 > /proc/sys/net/ipv4/ip_forward
but another test resulted in the same fashion (no internet on wired). I believe anything I add to /proc should have an immediate effect, correct?
View 9 Replies
View Related
Feb 9, 2010
I have a desktop computer running OpenSUSE 11.2 with two network cards installed. I would like to use both cards for connecting to the internet using different networks. The setting would be the following: eth0 is the main (default) card, almost all programs should use this NIC for connecting to the internet. eth1 is used only by a few programs, which have setting for selecting which network interface to use. The two NIC's are connected to different networks, so the IP address of the NIC's, the related subnet masks and gateways are also different.
Saying short, I would like to have the two NIC's as they would be in two separate computers. I can set the IP address and subnet mask of the NIC's. The main problem is that I can only declare one gateway. How can i setup this? I do not use network manager, I configure network cards using yast, but if needed I can of course use ifconfig directly.
View 9 Replies
View Related
Jul 30, 2010
I'm having a strange problem with my network connection/DNS. I turn computer the on and it recognizes and connects to wireless or wired but I can't access any Internet resources or my router. If I ping the default gateway, I get no response and I get DNS errors from any network services that run at start up. If I stop and start the network daemon then it all works fine until the next time I turn on my laptop. It does this for both wireless and wired connection.
I've tried to edit the network interface information in YaST but it says that configuration is handled by knetworkmanager and I have no idea where that information is accessed. I should point out that it all worked fine until I tried to connect to open WAP at my school and couldn't so I connected to the wired network. Next morning I had this problem when connecting to my home network. My questions are 1. What could be the cause of this error and 2. where does one configure the network interfaces when using knetworkmanager
View 4 Replies
View Related
Jan 31, 2011
I often use an Ethernet cable to connect my computer to another computer for various purposes. But when I do that, I cannot use the internet even though I'm still connected to a WiFi access point. I'm presuming that's because openSUSE is trying to reach the internet through the Ethernet cable, which has precedence over WiFi.Is there a way to enable internet usage via WiFi while I'm connected to another computer over Ethernet?
View 9 Replies
View Related
Mar 12, 2011
I have no Internet Access with Firefox
I first tried an upgrade from 11.3 to 11.4 and lost Internet Access, so i re-loaded 11.4 from scratch on clean partitions.
I am connected to my wireless WPA2/PSK connection, have an IP, am able to see the network.
I turned off and disabled the SUSE firewall.
I tried setting Firefox proxy settings to auto and to none, i dont use proxy.
I am currently posting this through an SSH connection to my 11.1 server from the new install of 11.4 on a Dell latitude D600 laptop (not using the on-board Broadcomm that is an issue for a later date).
I am running out of ideas anyone got a clue.
View 9 Replies
View Related
May 21, 2011
how to connect my network data card to run internet on openSuse..
View 4 Replies
View Related
Dec 18, 2010
I have just installed Ubuntu 10.10 64bit on my laptop Toshiba Satellite A665-S6065 and I can connect to wired network but I can not connect to wireless network "Network Connections disconnected". Im following this post http://ubuntuforums.org/showthread.php?p=6183681
1. Machine Brand and Model (PC/Laptop): Toshiba Satellite A665-S6065
2. Wireless Brand, Model and Wireless Chipset:
Code:
lspci
Output:
Code:
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
[Code]...
View 3 Replies
View Related
