wifi card:atheros ar5007egOS: openSUSE11.4My laptop can't connect on network after system hibernate. It has been asking me for enter the wifi password. But when I input the wifi password it still can't connect on network. I have to reboot it.
View 3 Replies
I'm moving from other distros. and I'm currently loving openSUSE and I'm probably going to stick with it for a long time.I have already googled for this, but I found no solution, but I figured this should be a common problem... Does google searches inside this forum?Now... for my problem, whenever I hibernate (suspend to disk) or sleep (suspend to ram) I can't resume my wireless connection nor connect to another.I don't know if this is an issue if I use cables, because I simply don't with my netbook:The hardware in question is an ASUS 1005HA eee pc, running openSUSE version is 11.3 fully updated. Didn't mess with wireless connections, nor kernel or hibernate settings
View 9 Replies View RelatedI clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View RelatedI recently installed suse 11.4 x64 onto my hp tx2000 tablet. everything has been working great including the wifi card. It's a broadcom 4328 a/b/g/n/bluetooth card and it was using the broadcom-wl driver. Earlier today i plugged in an usb wifi adapter to test whether it worked on suse plug and play. Well after plugging in and using this wireless adapter, my internal wifi card is no longer visible to the system. I've tried lspci and its not displayed. I booted into a different suse install and it wont work there. My bios does not seem to have a disable feature and the killswitch is in the correct position. The bluetooth is working but the wifi is not. In lspci i used to see "hp integrated (wireless+bluetooth)" and "broadcom 4328..." but now only the former.
View 9 Replies View Relatedi've installed openSuse 11.2 on my laptop (dell studio 15).Today at work i tried to connect to the wireless network, but i couldn't. First, the network card wasn't being recognized, but after a long time trying i was able to set it up, for this i used this command:
Code:
zypper in broadcom-wl broadcom-wl-kmp-desktop
So now, the networkmanager detects all the networks around, but i cannot (or i don't know
[code]...
I recently got a lenovo w510 laptop and I installed openSUSE 11.3 KDE on it. the wireless works fine at home (802.11g WPA2) when I go to work I have tried to set up the wifi for the 802.1X PEAP network but it doesn't look like it even tries to connect.
The work network set up is as follows. non-brodcasting SSID (do I need to tell network manager of this? I manually enter the SSID no problem)
Dynamic WEP 802.1X
PEAP
blank anonymous identity
no CA cert (I suspect this might be the problem)
PEAP v 1
MSCHAPv2
I have verified my username and pw several times, as well as the SSID. Just yesterday I helped a co-worker get on the network under ubuntu and it worked like a charm.
The Hardware profile displays the wifi card as a "WiFi Link 6000 Series" It is an intel card.
I just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies View RelatedRT2500 wifi card could not connect to wireless router using WPA personal.OS - RHEL4; Dell Inspiron C600; interface detected ra0
View 12 Replies View RelatedWhen i click the networks icon on the toolbar, these options popup:
Wired Network - (disconnected)
Wireless Networks (device not ready--firmware missing)
VPN Connections
I can click VPN connections and that's it. How do i get the firmware needed to connect to a wireless network?
It's tooken me this long to get Ubuntu and now I can't connect T_T
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies View RelatedWhen i click the button to connect to a wireless network this message apears:Network management disabled
View 1 Replies View RelatedHi I have istalled a D-Link wireless adaptor - with the help of this forum.
It is up and running - the light flashes and lsusb identifies it correctly, so does iwconfig.
I can, however, not connect to the network, and I noticed the following errors on boot up.
Trigering udev events: /sbin/udevadm trigger -- type: failed /etc/rc.d/rc.M: wlan0 Error for wireless request; "Set Nickname" (8BIC) information; "Any ESSID" Set failed on device wlan0; operation not supported.
Lower down I get
Starting rt2870 drivers . . . /etc/rc.d/rc.inet1: wlan0 information "Any ESSID"
Error for wireless request "Set Nickname" (8BIC) set failed on device wlan0 : Operation not supported
I have on two occassions seen sugstions to use wicd, but how do I use that?
i've been looking into OpenSuse for a while now, and finally got around to installing it, so far so good however i can't get my Laptops' wifi card to work, i can use my Eth0 chord but thats all. My laptop model is:Toshiba Satellite L755 with a intel pentium processorMy Network card is:02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01)Please get back to me on what i need to do to fix this, so i have a flawless installation
View 1 Replies View RelatedI have just installed openSuse 11.4 and have been trying to get my Edimax EW-7711In wireless card to work. I have downloaded and installed NDISWRAPPER but when I type ndiswrapper -i /path/to/rt2860.inf I get a message saying that this is the incorrect driver. However this driver drives the card for both Fedora 14 and Ubuntu 10.10, both using ndiswrapper, so what may be the problem with openSuse 11.4?
View 8 Replies View RelatedWireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
i am running on suse 11.3 on a laptop i missing the wireless under network it said not connected i done everything that is writte n i have acer aspire 5742 intel core i3 370m
[Code]...
I have a Laptop PC Acer Aspire 1710 and OpenSuse 11.2 installed on it I tried to setup my wifi card but it doesn't workI checked the log system log file.Apparently the driver cannot be loaded :
<6>[ 8.556483] b43-pci-bridge 0000:03:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
<6>[ 8.560204] ssb: Sonics Silicon Backplane found on PCI device 0000:03:03.0
<6>[ 8.581966] cfg80211: Calling CRDA to update world regulatory domain
[code]...
i have an Acer aspire 4920 laptop with opensuse11.3 installed and wifi card has identified home wifi, but for some reason when i enter the wpa-psk key it doesnt connect.i have been at this problem for several days and scanning the net for answers, without joy.i dont know about the command or terminal line, i have tried to type in commands but i get no joy.
View 4 Replies View RelatedI recently installed Suse 11.4 on my Dell Latitude 2110 netbook using the KDE live distribution, and, after that, the Broadcom wireless ceased to work. To enable the wireless connection, I have to press Fn + F6. If I do it now, the wireless led indicator turns on for a couple of seconds, then turns off again. Moreover, the option to enable the wireless connection in the network manager is greyed out
lspci output:
Code:
0c:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)
iwconfig output:
Code:
wlan0 IEEE 802.11abgn ESSID:off/any
Mode: Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit: 7 RTS thr: off Fragment thr:off
Encryption key: off
Power Management: off
dmesg output:
Code:
[8.330963] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.
[8.362403] brcm80211 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[8.362422] brcm80211 0000:0c:00.0: setting latency timer to 64
output of rpm -qa | grep broadcom:
Code:
broadcom-wl-kmp-desktop-5.100.82.38_k2.6.37.1_1.2-7.pm.8.1.x86_64
broadcom-wl-5.100.82.38-7.pm.8.1.x86_64
Is there a tutorial for how to set up a wifi connection for complete newbies to openSUSE? My laptop sees other routers, but won't let me connect to mine. I set WEP, HEX, type in the key, and then nothing happens. On the list it says this is unsecured, even though I have selected WEP.
View 2 Replies View RelatedI have an Atheros ar2427 chip in my Asus EEE 1001P and I'm using WICD to configure it. I can scan for wlans, but I can not connect. I installed the compat wireless package from yast and I downloaded the source from the compat wireless site and tried to compile it (which seems to be the solution for Ubuntu) but I got an error and an interesting warning
Code:
Linux linux-0yl2.site 2.6.34-12-desktop #1 SMP PREEMPT 2010-06-29 02:39:08 +0200 i686 i686 i386 GNU/Linux
[code]....
how to connect my network data card to run internet on openSuse..
View 4 Replies View RelatedAfter having scoured the internet and the forums for advice, I am still not able to connect via Wireless, which is being controlled by Network Manager.The following is info I obtained from running a script that I obtained reading these forums:
* Hostname: linux-8qpz.site
* Run date and time: Sun Oct 24 10:12:58 EDT 2010
---------------------------------------------------
[code]...
Im a Linux newbie and am running OpenSuse 11.3 (Gnome, 2.6.34.7-0.5-desktop Kernel) and Ive an Asus N13 wifi dongle (linux compatible). I currently connect using my laptopś internal wifi but I bought the dongle due to trouble with weak signal. It came with some sort of code that can be "compiled" but I havent got a clue how to do that (and I have been researching this matter for quite some time now). I then came across a post where someone with the same USB stick created and added only two small files to his filesystem and it worked...for him (maybe becasuse he was on a different Distro )
Ralink RT2870 USB Stick and created the two files mentioned in the post (network_drivers.rules and network_drivers.conf) and placed them in ETC... etc, etc! I rebooted the system but NetworkManager only lists it as "device not ready" ... So now back to square one.
[Code]...
I have a Dell Latitude E6500 running Opensuse 11.3. As far as I can tell the module for my wireless card is loaded correctly and it's working:
Code:
sudo lspci | grep -i wifi
0c:00.0 Network controller: Intel Corporation WiFi Link 5100
Code:
[ 556.642557] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:d
[ 556.642560] iwlagn: Copyright(c) 2003-2010 Intel Corporation
[Code].....
The funny thing is that it works fine in a Fedora installation, which has an older kernel and older drivers, on the same laptop. The fact that the indicator light doesn't come in when the physical switch is turned on suggests it's something to do with that switch.
1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
I currently have a WiFi network at home that serves two PC's, a Laptop (all SUSE 11.3) and a couple of WiFi radios. I also use IPCop as the Firewall. The system currently uses 802.11g, but the PC's and Laptop really struggle to achieve any reasonable internet data speeds, particularly as their RF range to the Wireless Router is very disappointing, so I have a couple Wireless Access Points. Unfortunately, whilst these WAPs might slightly improve RF coverage, connecting to the Router via one of them only serves to slow down the internet upload and download speeds even further. (Not much point in paying for expensive 4M internet access if I am only achieving a typical download of 500-600k!)
I want to completely replace my 802.11g with 802.11n - to both improve range and throughput. I'm looking at the 'Netgear Range Max Dual Band Wireless-N Gigabit Router' as this also has 2.4GHz (my WiFI radios are only 2.4GHz compatible). Unless, of course, anyone has any good reason to recommend I DON'T purchase it? My problem is that I am struggling to find up to date, accurate information that can advise me on which 802.11n (2.4GHz and 5GHz) PCI cards, PCMCIA and USB Adapters are compatible with SUSE.
I moved to Berlin recently and I got wireless internet through an access point. I'm supposed to use the laptop's built-in wireless netcard to access the internet. This usually works in windows (connection falls out from time to time), but I have yet to make it work in linux. I'm using OpenSuse 11.3 64-bit and the Knetwork manager. Most of the settings in the network manager are correct, but it keeps wanting to use system certificates for the server. By that I mean it keeps checking 'Use CA System certificates'.
So I can't choose the CA-certificate supplied by my internet provider. I keep removing the check-mark and pointing it to the 'hotzoneCA.der' certificate. I also got a 'personal' certificate, in lack of a better word. Its called 'jacob_collstrup.p12'. The Knetwork manager seems to accept the 'jacob_collstrup.p12' certificate, but not the other one.
I just put the certificates in a folder like this /jacob/home/hotzone/zertifikate/ I can see the network fine using the Knetwork manager, and the signal strength seems ok. Not too good, but it shouldn't be a problem. I might have messed up the system, since I first tried this guide, prior to experimenting with Knetwork Manager:
1. (had to run this one as su)
Code:
wpa_supplicant -w -i wlan0 -c /etc/wpa_supplicant.conf -Dndiswrapper -dd �t
2. (This was supposed to be put in a wpa_supplicant.conf file)
Code:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
opensc_engine_path=/usr/lib/opensc/engine_opensc.so
pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so
pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so
[Code]...
I cant seam to find out how to get my card to work i cant find out how to install the driver or finding the wifi card on the system.
View 9 Replies View RelatedI'm running the 64-bit version of Fedora 12 on a MacBookPro5,1 system. I am unable to connect to my wireless network, which shows up in the list of available wireless networks.
I will enter my password and the system will try for several seconds to establish a connection and then fail.
I know the network is fine because I can connect to it when I boot the computer in Mac OS X.
What can I try that will allow me to connect to my wireless network under Linux?
