I have a windows machine on my lan with a printer attached. I have samba running on my F11 laptop and I can use it to access shared files on the windows machine. But how can I use the printer from fedora? When I go to Administor>Printers then I just get an empty list, even after pressing 'rescan'. Do I have to change some firewall/samba configuration? If not then where else would I see the printer?
View 2 Replies
I'm running Fedora 11 and printing to both an HP Laser Jet 4Plus and HP Office Jet 7130 via a Windows 7 PC. I have a UID/PWD account on the PC that differs from that on the Fedora, also one that is identical UID/PWD to that used in Fedora. This has worked fine until "recently" (noticed it in ~last week or 2). Suddenly I'm being asked repeatedly to authenticate to print, neither account credentials are working. I get the message "Tree connect failed (NT_STATUS_ACCESS_DENIED)" and I get nowhere. I tried delete and reinstall the printers in Fedora, that works OK, can "see" them in setup on the Windows 7 host just fine. But can't get past the repeated authentications ...? I'm guessing something has changed in Fedora updates because this used to work with same Windows 7 PC in prior weeks.
View 1 Replies View RelatedI have a virtual Linux box with a static IP in the cloud.
I have remote sites that have networked PCs that normally act as terminals but also have more than one printer on the Windows Network.
I would like software on the Window's machine to access the known IP address of the server and advertise the printers on the network so they can be printed to with lpr or cups. I don't have a problem manually setting up the printers on Centos if that is necessary. (But I need to know how to do that as well).
I need to know if I can setup a VPN on Windows without it stopping regular internet traffic and how to do it.
I need to know all the steps (what to install, what to issue commands for) to make this happen without using a GUI if possible and if the GUI is easier I need to know which GUI to install.
I also do not have a problem with using a VPN router at the client side if that makes it any easier. Like a Cisco RV120W.
I want to print from my linux box to my win7 pc that has a shared printer. I have cups installed and tried to add pritner using samba, but was unsuccesful, gave me an error when trying to add. The guide i followed is: Yet another Linux to Windows printing tip -- Debian Admin The printer model is a dell 2330d laser printer, it is not in cups, so i added the ppd file i got off the dell support site. I am aware that there is a native suse driver, but i want to print to the windows printer.If possible I would like to know how to do this via command line instead of the GUI.
View 9 Replies View RelatedI am currently running Lucid on my system and can't seem to get my printer on a Windows XP computer to print documents sent from my Ubuntu computer. I can see the Windows XP computer in Nautilus under Network and can even access the shared files on the Windows computer with no problem. I have been able to install the Windows shared printer on my Ubuntu computer using System>Administration>Printing>Add>Network Printer>"Windows Printer via Samba" without any error messages. The problem is that whenever I send a printing job to the shared printer, the printer acts like it is going to start printing then automatically stops just right before the paper is going to be fed. I have memorized the noises my printer makes right before the paper gets fed. That is how I know it stalls right before the paper is about to be fed.
When I check the print queue on my Windows computer, its status is "printing", but it never does. I have tried this with two different HP printers (Deskjet 3940 & PSC 1410), and it is the exact same problem on both.
We want to print PDFs from a Linux server to a HP LaserJet 1320 PCL 6 which is attached to a Windows print server.
The command we use is
lp -d LaserJet sicl_rcpdebtnt_5.pdf
Problem is, the printout comes with the top 10% of the page not printed. i.e. the printing starts from about 10% of the PDF. The header and top information is not printed.
We tried the scaling option:
lp -o scaling=75 -d LaserJet sicl_rcpdebtnt_5.pdf
But that also has no effect. Only the characters become smaller but still the same problem is there.
What can we do to print the entire PDF in ONE page. When we open the PDF in Windows and print it we have to say Fit to printer margins for the printer's page scaling property.
How to set this in command line Linux?
I have a OpenSUSE 11 machine set up as a domain controller. I have set my printer up to be shared to Windows machines logging into the domain. I was able to install the printer to my Windows machines. When you go to the printers folder in Windows, it shows the printer but says "access denied" instead of the usual "ready". If I print to the shared printer the job will go through. I am thinking it is an authentication issue because if I log into Windows machine as "root" and let it build a profile, the printer doesn't show the "access denied" message. How do I allow other users to have access to the printer?
View 1 Replies View RelatedI apologize if I'm a little wordy. I'll give the problem, then a detailed list of my setup (to help troubleshoot). Problem: I can't print from Ubuntu 10.4 on my Win7 shared printer. I also can't connect to the Win7 computer sharing the printer (probably a related problem).
Error Message:
1.) I click on Places, Network, Windows Network. I get an error that says "Unable to mount location, Failed to retrieve share list from server."
2.) I click on System, Administration, Printing, Add, Printer, Network Printer, Windows Printer via SAMBA, Browse..., and I get this error "No Print Shares, There were no print shares found. Please check that the Samba service is marked as trusted in your firewall configuration. To do this select System->Administration->Firewall from the main menu."
Network Configuration: I have a wireless/wired network (using a router) where the Ubuntu machine connects wirelessly and the Win7 machine connects wired. The Win7 machine is on a Win7 homegroup and custom named "workgroup". There is a username/password to log into the Win7 Machine. My other Win7 laptop connects just fine to the Win7 desktop's shared printer (and network drives). I know it isn't a issue of it not working (at least with other Win7 machines)
Problem: I'm assuming there is probably a setting in Win7 that needs adjusting (although I've looked at about everything I can find). I also don't know much about Ubuntu so it could very well be something I need to setup in Ubuntu. I checked already to make sure that SAMBA and the smbfs plugin is installed.
How can I get my MacBook running OS/X on my wireless network to recognize and print to an HP OfficeJet 6110 printer attached to a desktop workstation that's running Ubuntu Linux 11.04. It had no problems finding the printer when it was attached to a Windows machine, but you know about Windows...
View 3 Replies View RelatedI have a 64 bit laptop and i am using the 64 bit version of ubuntu 10.10. i am wanting to setup a lexmark x4650 printer which has wifi built in and can do wireless printing. i have the driver from lexmark installed but it is the i386 version which i know is the 32 bit version. and i know that 32 and 64 bit versions don't work so well together. i've gone through all kinds of help on these forums and for some reason when go to print a test page, it comes back with an error statement. i will have to try it again so i can post it verbatim.
i have a similar thread in the 64 bit thread so if it can be locked or deleted and have just this one, that would be cool. this same printer is not connected to any computer for it's wireless printing ability. it is a stand alone but all of my families laptops can use it since they have the software on theirs. they are using windows 7 which is what i have also, but i am switching to linux since i am not a fan of microsoft at all. i despise everything they do. i love linux and the community around it and i just want to get this printer setup so i can make the last and final switch. this is the only thing holding me up.
I've recently decided to migrate the infrastructure in my workplace from ubuntu to fedora, every thing except the printers went perfectly. When I try to print as an user It just throws an generic error and stops, as a root it doesn't even show the error.
This is the debug log:
Code:
D [28/Apr/2010:04:22:03 +0200] cupsdSetBusyState: Dirty files
D [28/Apr/2010:04:22:03 +0200] cupsdReadClient: 12 POST / HTTP/1.1
D [28/Apr/2010:04:22:03 +0200] cupsdSetBusyState: Active clients and dirty files
D [28/Apr/2010:04:22:03 +0200] cupsdAuthorize: No authentication data provided.
D [28/Apr/2010:04:22:03 +0200] cupsdReadClient: 12 1.1 Get-Jobs 1
D [28/Apr/2010:04:22:03 +0200] Get-Jobs ipp://localhost/printers/ .....
It worked fine in debian and ubuntu, so we can assume that the drivers are ok, any ideas?
i recently installed fedora 14 xfce and i have a printer laserjet p1007 hp connected. the printer gets detected but there is an error while installation (i.e when i run hp-setup) it gives an error that some binary drivers missing. i refreshed the package list also. but still the driver does not get installed..
View 1 Replies View RelatedI have recently installed Fedora 13 dual booted with windows 7. Everything on both OS's works fine with the exception of Linux printing. I am using a Netgear WGPS606 print server. (it works fine on Windows 7). I have, from Linux pinged the server (192.168.1.200) and have gotten a response for each string sent but following the usual procedure [System-Administration-Printing then Add (a printer)- Expand Network Printer etc.] The response is that there is no printer found at that address. (the firewall was disabled).
View 4 Replies View RelatedI am a new convert to Fedora with very little knowledge of Linux in general. I have managed to install Fedora 11 on my Advent 8315 laptop and I have wireless connection via my Belkin Wireless N modem router. I have always been able to setup Windows networking successfully but Fedora is much more complex, using terminology that I am not familiar with. What I need to do to achieve networking with my Windows computer? I especially want to network to my Canon printer which is connected to the Windows PC.
View 6 Replies View RelatedI am trying to share my printer with a windows xp machine.Samber server and configuration tool is installed. Still I have no clue how to get this to work. The printer is setup and working on my Fedora desktop.as anyone done this before and can give a step by step description on how to setup a Linux printer on a network (home-network) with windows.I already searched for it but non of the tutorial were clear enough or missing something.
View 12 Replies View RelatedI have been able (with some hair pulling and gnashing of teeth) to print from outside the LAN to the printer connected via USB to the desktop computer at home, until the last upgrade. The laptop will forst say the printer may not be connected, but eventually (usually) after a while says the job was sent to the printer. The log files on the desktop - serving as the printer server have an error message in cups/error_log that I am not familiar with, and don't believe I have seen before. I am sure if I could decipher that error and figure out how to change the behavior to get rid of it, it would once again work. Printing from within the LAN is a no-brainer as it has been for the last several releases. The error that I get when trying to print outside the LAN (via the internet) is:
cupsdAcceptClient: 12 from <WAN IP>:631 (IPv4) Unable to encrypt connection from <WAN IP> - GnuTLS internal error. I am missing something as far as authentication from the laptop to the desktop. how to fix it.
I have a machine running fedora 10 that has a printer in cups that i want to share to the windows machines on the network.I cant find any mention of shareing printers in the cups interface
View 1 Replies View RelatedI am trying to set up printing on my Fedora 14 laptop, on my home network.
Details:
- Home network, single subnet, the desktops are connected to the switch portion of my Linksys via Ethernet and all have static addresses. Name resolution between them is via hosts file entries. The router is running wireless (WPA2/AES/DHCP) to accommodate my laptop which is dual boot XP Pro and Linux Fedora 14.
- The printer is an HP Deskjet F4180 printer. It is attached via USB to a Windows XP Pro box and shared. The XP box is wired and static ip.
- I am able to see all the shares and print to the shared printer from any of the Windows boxes, wired and wireless, including my laptop when I run Windows on it.
- My Fedora 14 is working fine on wireless, using Network Manager and KDE desktop. I am able to access all the Windows shares on both of my wired desktops. One desktop is XP Pro, the other is Windows 7.
This is what happens when I try to set up printing on Fedora:
- I go to Administration / Printing and click to Add a Printer.
- I am prompted for the root password twice, which I put in.
- I select Network Printer / Windows printer via samba and click on Browse...
- It finds my WORKGROOUP and machine name mig29 and prompts for user ID and password which I type in.
[code]....
the user ID and logon on Fedora is different from the one on Windows. During setup I am prompted for credentials. It seems to me that somewhere down the line Fedora supplies not the credentials I supply but my local user ID and password and it obviously fails.
I have a FC11 box, with an HP prineter attached. I trying to print from my laptops after I have setup samba and shared the printer , It was working fine when I was installing FC4 and FC5. I am not sure what is missing. when I tried to print from the XP box I got "Test pge failed to print" error.
View 9 Replies View RelatedI just upgrade to Fedora 11.
I have problem in installing the printer, no matter add printer in local network or Windows Printer via Samba.
The summary is as follow:
I have download a printer driver and had installed but got error when I tried to printer a test page.
I have a problem with a bad entry in my system-config-printer on my notebook computer which I think is interfering with my ability to print. I run fedora 10 on several systems in my house. On one desktop, I have a printer hosted which I think I have successfully setup for wireless network sharing (an HP895) using IPP.My problem seems to be a bad entry in my system-config-printer on my notebook computer which seems to stall when I try to print from applications (Firefox for example.) on the notebook. If I open up "Printing", I have 3 printers listed... one of them is for when the printer is attached directly to the notebook, one of them is the working printer description "printer" and the 3d is the bad entry. If I click on the bad entry to try to delete it, I don't have that option, but If I try to look at the "properties" for that entry, system-config-printer stalls (as do other applications when the printing dialog box starts up, and I have to force them to shut down.)
I will attach some screenshots and a copy of my /etc/cups/printers.conf file.How do I get rid of this "bad entry" in the system-config-printers GUI ? It doesn't seem to exist in the printers.conf file.
I have installed Fedora 12 with latest updates. My problem is printing from Winstar Networking USB 2.0 Server (WS-NSU62P). This device is attached with LAN cable to Windows XP machine. HP LaserJet 2200d is connected on WS-NSU62P with USB cable. This printer works fine with Windows clients (when you add printer with standard procudure for WinXP OS). Before adding the printer I have to install some drivers witch i found on install cd. I didn't found any drivers for Linux. Specification has info about supported protocol on WS-NSU62P (Network Protocol IPX, TCP/IP, NETBUEI, APPLETALK, LPR, smb (Over IP)
How to set my Printer configuration in Fedora 12 to enable printing from HP LaserJet 2200d connected on Winstar Networking USB 2.0 Server (WS-NSU62P)?
I'm having trouble with printing a PDF that is in landscape mode. When I tell Okular or Adoble Reader to print a document in landscape mode, the text is Illegible. If I tell it to print as portrait mode, then I can read the text but the end is cut off and there is no way for me to tell Okular or Adobe Reader what the margins are. That option was grayed out.
I'm having another problem: When I cancel the job from the CUPS interface, it says it canceled the job but the printer keeps going and finishes whether I want it to or not. With 11.2, I was able to have it set up so that when I told it to stop the printer, it did so right away. Why can't I get the printer to stop in the middle of a job if I see something wrong with it so that I don't have to waste ink?
How do I stop a printer from printing? Here's what happened- I started to print some PDF stuff and then changed my mind. The printing job hadn't finished so I just clicked on the printer icon and selected QUIT. Well, of course that didn't work so I just turned the printer off......same result- when I turn the printer back on it keeps on printing the same stuff. How do I stop the printer from continuing and delete all print jobs?
View 2 Replies View RelatedI have installed an HP LaserJet 2200 network printer using CUPS successfully and can print test pages and stuff from OpenOffice, Evince etc. But no luck printing from lpr. Using lpstat seems to suggest all is well:
$ lpstat -t
scheduler is running
system default destination: HP-LaserJet-2200
device for HP-LaserJet-2200: socket://192.168.10.42:9100
HP-LaserJet-2200 accepting requests since Tue 19 Oct 2010 14:01:50 NZDT
printer HP-LaserJet-2200 is idle. Enabled since Tue 19 Oct 2010 14:01:50 NZDT
Ready to print.
If I now try to print 'test.txt' using:
$ lpr test.txt
nothing happens. Try calling the printer by name:
$ lpr -P HP-LaserJet-2200 test.txt
lpr: HP-LaserJet-2200: unknown printer
I have added my user name to the lp and lpadmin groups. Trying the above as 'sudo' results in the same result. The only thing I've noticed is that when printing something from OpenOffice, in the document print status I get the message 'Processing - not connected?', although printing still works.
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_NZ.UTF-8, LC_CTYPE=en_NZ.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
In December I finally filled up my root partition and broke Suse 11.1. I therefore resized my partitions and installed Suse 11.3 on /root. I didn't not touch my /home partition.
Last week I had a paper jam in the printer. This has been cleared and as far as I know the printer is now fine. However the printer will not print. In url, it says printing has been paused, but I cannot find resume printer/printing anywhere.
I have tried Google, but the instructions do not appear to match where I would find 'resume printer'.I am able to provide further information.
I have an HP C4795 printer and lately when I print something nothing happens until I reboot and then the printer will print. How can I fix this problem? This was printing from Okular pdf reader.
I'm running openSuse 11.3 KDE 64 bit.
I am not sure if this is the right place for this or not, but I am having a problem getting my HP6300 series all in one printer to print photo's with proper colors, all colors seem to run. I have hplip installed and set up to print photo's and it still prints colors like runs instead of correct.
View 9 Replies View RelatedI have a brand new Canon MF4350d printer/copier/fax/scanner installed and shared on XP that I can't get working on Ubuntu!
XP prints test pages fine. Ubuntu sees the XP shared printer, it sends print jobs, and the XP machine even receives the print jobs (I can see them "spooling" in the XP print manager) but then nothing happens. The job leaves Ubuntu showing 150k but then shows 50 bytes when received in XP before disappearing from the queue.
How I got to where I am...
There was no native driver in Ubuntu for the printer, so I downloaded Canon linux drivers source and compiled (including make install) based on some other threads I've found such as this one.
Compiling left me with PPD files that seem to be specific to the MF4350, although their names show MF4350z not MF4350d. I'm not sure why there were three different files with slightly different names (CNCUPSMF4350ZJ.ppd, CNCUPSMF4350ZK.ppd, and CNCUPSMF4350ZS.ppd).
I added the printer manually using the Ubuntu printer browser setup (Samba) and selected the .PPD files manually. I've tried all three different .PPD files to no avail.
I've toggled bi-directional comm. and tried different print drivers on XP. Nothing's worked yet.
Been using ubnutu gnome for a loooong time and my printer (Canon MX340) has been running just fine, configuration and usage.
I now switch to kde. configure my printer the same way i would under gnome and as soon as i send a job, it processes for about 3 seconds and just marks "stopped" under status. nothing goes through anymore!!
i've updated from 4.5 to 4.6 with backports and nothing is happening on there either.
im running maverick amd64 and using the i386 drivers (with dpkg -i --force-all) which are still recognized even under kde.
p.s.: the printer normally runs as wireless standalone (no samba/cups involvment whatsoever)
