Debian Configuration :: No Printing From LPR - Unknown Printer
Oct 19, 2010
I have installed an HP LaserJet 2200 network printer using CUPS successfully and can print test pages and stuff from OpenOffice, Evince etc. But no luck printing from lpr. Using lpstat seems to suggest all is well:
$ lpstat -t
scheduler is running
system default destination: HP-LaserJet-2200
device for HP-LaserJet-2200: socket://192.168.10.42:9100
HP-LaserJet-2200 accepting requests since Tue 19 Oct 2010 14:01:50 NZDT
printer HP-LaserJet-2200 is idle. Enabled since Tue 19 Oct 2010 14:01:50 NZDT
Ready to print.
If I now try to print 'test.txt' using:
$ lpr test.txt
nothing happens. Try calling the printer by name:
$ lpr -P HP-LaserJet-2200 test.txt
lpr: HP-LaserJet-2200: unknown printer
I have added my user name to the lp and lpadmin groups. Trying the above as 'sudo' results in the same result. The only thing I've noticed is that when printing something from OpenOffice, in the document print status I get the message 'Processing - not connected?', although printing still works.
I recentlty did a new install and the printer icon no longer shows up in the notification area when printing....I cannot figure out what is missing or did they omit this...
I've bought a HP Photosmart printer, HP Photosmart wireless e-All-in-One printer - B110a and i've got a problem installing it properly. I'm using Debian 6.0 Squeeze. When i connect the printer, Debian doesn't recognize my printer as the Photosmart B109 printer for unknown reason. When i go to the site of HP and search for a driver, it directs me to this site:I've downloaded that latest hplip file as a .run file and installed it. My printer is recognized proparly, but when i try to print a colored image, it comes out black/white. Something is not crrect. Does anyone recognize this problem with this type HP printer?
Just installed fedora 14 and do not have a printer config app. Im not sure what packages should be installed. I just came back to linux after years off. Lots different from redhat 6.
I recently installed office 2007 under wine, but since I have it no longer know what to open .doc or .xls files with, I was using Gnumeric but now when i go to Properties -> "Open with" there is no longer anything in the list and even when i attempt to add to the list nothing comes up. If anyone know what way you can manually add file types and associate them with programs
I'm using an up-to-date installation of Squeeze with the default Gnome desktop and am trying to print. My knowledge of configuring printers is very limited if it even exists. Since a friend of mine is able to print from her Ubuntu computer, my plan is to copy her. Here's how she does it. She goes under System->Administration->Printing on the desktop. Then a window pops up titled "Printing" that lists various printers that are supposed to exist. It's possible to add one by selecting Add->Printer. It asks for the root password and then a new window pops up titled "New Printer" which has a subwindow called "Select Device" In my case, the "Select Device" window has the following options to choose from:
- AppSocket/HP JetDirect - Internet Printing Protocol (ipp) - LPD/LPR Host or Printer
In her case, she has an extra option called "Windows Printer via Samba". This is the option that she uses. The other options don't seem to work for her. I'm assuming that I just need to install some package in order to make this option magically pop up for me. Does anyone know what package this may be? I currently have the packages smbclient, samba-common and samba-common-bin installed..........
After updating and subsequently restarting today, I can no longer bring up my wireless interface:
ifup wlan0 SIOCSIFFLAGS: Unknown error 132 Could not set interface 'wlan0' UP SIOCSIFFLAGS: Unknown error 132 SIOCSIFFLAGS: Unknown error 132 Failed to bring up wlan0
iwconfig lo no wireless extensions. eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID: off/any Mode: Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr: off Fragment thr:off Encryption key:off Power Management:off
on my dual HD5500/GT940M. I can not turn on Nvidia. just install bumblebee and got the error "unknown header type 7f" if I remove bumblebee, Nvidia 340 loaded but system run on HD5500, no way to use Primus or to switch to 2nd card.
Gnome-disk-utility doesn't show filesystem type, mount point, filesystem label, size¦ of my / filesystem.
I am running Debian Squeeze using lvm2. I have two HDDs and each has one primary partition, which are used as PVs. Having two VGs, each VG has it's own PV.
There are some LVs and all of them except the LV holding the swap space are formatted with XFS. Now gnome-disk-utility shows everything about my /home LV, another LV containing a whole Ubuntu installation,¦ only the / LV (and Swap LV, but I don't know what it is supposed to show there) is/are missing nearly all information.
Otherwise the system is running perfectly well and the Debian / LV is shown normally in Ubuntu's disk-utlity, as well as all other LVs.
fdisk
Physical volume
Volume group
Volume group
lvdisplay
Logical volume
Logical volume
Logical volume
Logical volume
Logical volume
DebianCopy is a copy of my Debian installation (different fs label and UUID). DebianII (again different UUID and label) is a copy too, but there I tried out newer (testing) versions of udisks/lvm2/udev and right after the upgrade it showd everything as it should with the additional advantage of the newer udisks-version showing my VGs, but after a reboot it showed the same behaviour as before or even worse, because the information about other LVs was missing too.
In the end I even modified the fstab. Originally it contained the /dev/mapper/vgbay... entries and I replaced them with LABEL=... and finally with UUID=..., but it didn't make any difference either.
I have just upgraded to Jessie and everything seems to be OK apart from printing from a windows machine to my print share. This was working previously under wheezy. I can print a test page from Cups without any problems, but when I try and print from windows, Samba seems to crash completely and is constantly writing these messages to the logs. Then I lose access to the other shares, presumably while it repeatedly crashes.
STATUS=daemon 'smbd' finished starting up and ready to serve connectionsPANIC: assert failed at ../source3/printing/printing.c(486): pjob->jobid == jobid [2015/09/22 12:02:03.989596, 0] ../source3/lib/util.c:785(smb_panic_s3) PANIC (pid 3704): assert failed: pjob->jobid == jobid [2015/09/22 12:02:03.991930, 0] ../source3/lib/util.c:896(log_stack_trace) BACKTRACE: 27 stack frames:
I believe this has something to do with an mdadm update which was included in the release. When I configured the array, I didn't partition the disk devices, so maybe that has something to do with it. I am thinking of rebuilding the array and partitioning prior to build, but a quick fix would be referable.
And also something appears to have happened to the raid device since the update.
Prior to update, the array was /dev/md0 - now it is /dev/md/0 which is a symbolic link back to /dev/md0.
mdadm --detail --scan now reports /dev/md/0 where previously it reported /dev/md0
I created a new RAID1 array on a fresh system and immediately after the create, these messages appear at 5 minute intervals.
I have Ubuntu LTS 10.04.2 x86-64 running with default Cups installed. Now I am trying to print on a Canon iRC1021i network printer using a x64 PPD file. Trying to print a test page delivers a "server-error-internal-error".
After this I ran the debugging mode which delivered the troubleshooting.zip file.
I have an "HP Deskjet d1400 Series" using the "hpijs, 3.10.2 (color)" driver. When I attempt to print a test page from the CUPS web interface, it works. However, when I try to print from an application, such as Okular or Iceweasel, the only option is "Print to file". I have hpijs and hplip installed.
I have finally given up trying to get to a printer on my windowsXP pc to work with my linux box and need some assistance. The printer is a hp photosmart c5500 series. My linux box is running lenny and I have installed the cups and samba applications. The linux box is networked to the win pc on a win network using a eth0 link. The link works as I have internet and e-mail connections. I have configured the smb.config file as follows:
[Code].....
I have run the tests in the samba checklist and the connection is apparently working. Pings to the windows pc,, the notebook, and the linux box all return the proper results. The "smbclient -L w.x.y.z" return shows the windows shares that includes the above named printer. When I try to connect the printer using the kde cups wizard or get into the c drive on the windows pc I get the NT_status_access_denied message. I get the same return when I try the "smbclient //username:passwd@wincomputer" I downloaded the appropriate drivers from HP and tried the lpadmin comand and instructions in the Debian mini-Howto but get the return of "lpadmin: No such file or directory" when in fact all the files exist and have correct permissions etc. I have a Ubuntu OS running on a notebook computer (dual boot with windowsXP) with a wireless link to the same router that accesses the printer without a problem. The smb.conf file I am using is based on that I found in my Ubuntu OS but apparently something is different.
I have the printer Canon i-SENSYS LBP6020. I followed the instructions from the site URL....There are no errors, but when I try to print, nothing comes out of the printer.My system is: Debian GNU/Linux 8 (jessie)Here is some debugging information:
Error log while printing from a CANON LBP6020: URL.... Troubleshooting information while printing from CANON LBP6020: URL....
I have just set up the above OS, however, installation did not find my network and therefore APT additional software & security updates could not be accessed.The network was simple to setup post installation.I have uncommented a few sources in the sources list file but obviously that does not,in itself, suffice to get accessability. I am also unable to configure my supported HP printer and I assume that can only be done with an additional package via APT.
I run Debian Squeeze but I have the system installed step by step from minimal installation. So I'm not sure if I have forgotten basic packages important for printing. I open system-config-printer to add a new network printer. In the list of the Network Printers after some seconds it appears the HP Color LaserJet 2600n. I chose it and hit Forward. A new window opens that says that system is searching for Drivers and finally I'm ready for printing.
I am unable to figure out how to set up a net work printer with new squeeze installation. I have used cups ver 1.3.8 on lenny and have never had any difficulty, this new version 1.4.4 I'm unable to gain any ground with.I did a purge and re-install with no luck?
I installed the Gnome desktop CD1 AMD 64 version of Debian Squeeze. I installed samba and python-smbc. I am missing samba printers in my system-config-printer. Anyone know why? [url]
Our Canon MX340 printer is WiFi connected using an IP address. This works well except that whenever the printer is turned off (for any reason) it chooses another IP next time it is turned on. As near as I can tell, it has two IP numbers: 192.168.1.64 and 192.168.1.65 Is it possible to enter both in the CUPS configuration so that CUPS will find the printer whichever number it is using?
I use a 'wifi hotspot' provided by my mobile (android) phone for internet/email and to connect to my wifi capable HP p1102w printer. Installation and use of the printer worked perfectly until I bought a new phone, again android with 'wifi hotspot' capability. The wifi connection on my new phone works fine for internet and email but it totally fails to detect my printer.
I have tried to detect and connect to the printer using system-config-printer and using the HP utility hp-setup. Both fail to detect the printer on the 'new' wifi network.
The old network connection which detects the printer as expected gives the following output:
Code: Select allpat@debian:~$ ifconfig eth0   Link encap:Ethernet HWaddr 6c:3b:e5:91:ec:0c      UP BROADCAST MULTICAST MTU:1500 Metric:1      RX packets:0 errors:0 dropped:0 overruns:0 frame:0      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0      collisions:0 txqueuelen:1000      RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[Code] ....
The new (problematic) network connection which fails to detect the printer gives the following output:
Code: Select allpat@debian:~$ ifconfig eth0   Link encap:Ethernet HWaddr 6c:3b:e5:91:ec:0c      UP BROADCAST MULTICAST MTU:1500 Metric:1      RX packets:0 errors:0 dropped:0 overruns:0 frame:0      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0      collisions:0 txqueuelen:1000      RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
reason my Debian 5 system will not stop printing blank pages. I've got the CUPS system installed, and I've gone to the control page and canceled everything. I've also turned the printer off and restarted it several times. Every time it comes back online it starts printing blank pages again. My paper does not need to be heat treated. It's fine as it is. So, how to I stop this waste of electricity and printer MTBF? What else might be sending commands to the printer besides the CUPS system?
I have a printer connected locally to my Debian box. It runs fine via cupsd.I am also running a Windows 2003 VMware guest which I would like to use the printer (use as a local printer, not a network printer).
VMware offers a connection via USB, so it should work. The printer I have plugged locally into the Debian host is recognised by the Windows 2003 guest, but it won't print. I get an error message saying that the printer is still connected to the host OS, and that I need to remove (or presumably disable) the host driver before the guest can use the printer.
So how can I find out which printer driver/module is being used by the Debian host to connect to this printer? And what is the best way to temporarily disable it, while my VMware guest is running?
how to get clients connecting to an office printer. during a migration from windows server to debian/samba.
We have:
5 windows XP machines one Windows Server 2003 machine, PDC of the old domain One debian Samba PDC (of TEST domain)/print server (with CUPS installeD) running in a virtual machine hosted by the windows server One Toshiba eStudio 3511 printer
Using the CUPS control panel, I've been able to autodetect and add the printer, and it appears as an available share in SWAT for samba. However, the driver isn't perfect. CUPS could only supply drivers for the 3510c, not the 3511.
However, clients on the TEST domain are unable to access it. Doing so gives an error about a local policy preventing a connection to the print queue. I've tried googling this error and the fix that comes up in every result about changing a point and print policy setting, does not work.
however, I've been able to work around the issue. by first logging in as local administrator, navigating to the domain server, then inputting the domain root account credentials at the prompt. That allows me to attempt to connect to printers, but with a different error
"The server for the printer does not have the correct driver installed...."
I very strongly suspect that the 3510 driver actually will work, but it's just not being shared properly. The printer driver share folder is /var/lib/samba/printers, and that directory contains only a few empty subfolders. CUPS did not place the driver there as I would expect, and that is where clients are looking for it.
The thing is, I have no idea where CUPS DID put the driver.
On the old domain, the printer uses drivers for es4511, and looking on the toshiba site, this seems to be what they provide. The Toshiba Site provides a huge variety of drivers, including several windows ones, a universal driver, and a CUPS PPD. Cups asks for an optional PPD during install and I tried supplying that. It said installed successfully, but didn't change anything.
I've tried pasting the windows drivers into /var/lib/samba/printers/W32X86 too, and likewise with other drivers from toshiba's site. but this doesn't change anything either, so I'm at a bit of a loss.
how to install/setup drivers on a samba PDC, for windows machines?
Also relevant, my smb.conf: anyone see any possible causes of problems? # Samba config file created using SWAT # from UNKNOWN () # Date: 2010/08/19 13:03:07
I'm running Fedora 11 and printing to both an HP Laser Jet 4Plus and HP Office Jet 7130 via a Windows 7 PC. I have a UID/PWD account on the PC that differs from that on the Fedora, also one that is identical UID/PWD to that used in Fedora. This has worked fine until "recently" (noticed it in ~last week or 2). Suddenly I'm being asked repeatedly to authenticate to print, neither account credentials are working. I get the message "Tree connect failed (NT_STATUS_ACCESS_DENIED)" and I get nowhere. I tried delete and reinstall the printers in Fedora, that works OK, can "see" them in setup on the Windows 7 host just fine. But can't get past the repeated authentications ...? I'm guessing something has changed in Fedora updates because this used to work with same Windows 7 PC in prior weeks.
I'm having trouble with printing a PDF that is in landscape mode. When I tell Okular or Adoble Reader to print a document in landscape mode, the text is Illegible. If I tell it to print as portrait mode, then I can read the text but the end is cut off and there is no way for me to tell Okular or Adobe Reader what the margins are. That option was grayed out.
I'm having another problem: When I cancel the job from the CUPS interface, it says it canceled the job but the printer keeps going and finishes whether I want it to or not. With 11.2, I was able to have it set up so that when I told it to stop the printer, it did so right away. Why can't I get the printer to stop in the middle of a job if I see something wrong with it so that I don't have to waste ink?
How do I stop a printer from printing? Here's what happened- I started to print some PDF stuff and then changed my mind. The printing job hadn't finished so I just clicked on the printer icon and selected QUIT. Well, of course that didn't work so I just turned the printer off......same result- when I turn the printer back on it keeps on printing the same stuff. How do I stop the printer from continuing and delete all print jobs?
I am unable to add my USB printer via the YaST2 Printer Configuration setup tool in openSUSE 11.3. The printer, a Dell Color Laser 1320c, was last used with openSUSE 11.2, and setup was entirely uneventful. No driver is provided by Dell, so I used the Fuji Xerox DocuPrint C525A Linux driver. The problem: To add a print queue in 11.3, a Connection must be specified (parallel, USB, network, etc). However, the configuration wizard fails to show the presence of the USB print device.
[Code]...
This printer was working just eight weeks ago under 11.2, and 11.3 is obviously able to detect its presence and identify it correctly. I feel certain the solution is simple, but I haven't found documentation that provides the answer.
I have a windows machine on my lan with a printer attached. I have samba running on my F11 laptop and I can use it to access shared files on the windows machine. But how can I use the printer from fedora? When I go to Administor>Printers then I just get an empty list, even after pressing 'rescan'. Do I have to change some firewall/samba configuration? If not then where else would I see the printer?
In December I finally filled up my root partition and broke Suse 11.1. I therefore resized my partitions and installed Suse 11.3 on /root. I didn't not touch my /home partition.
Last week I had a paper jam in the printer. This has been cleared and as far as I know the printer is now fine. However the printer will not print. In url, it says printing has been paused, but I cannot find resume printer/printing anywhere.
I have tried Google, but the instructions do not appear to match where I would find 'resume printer'.I am able to provide further information.
