Fedora Installation :: Install Software Crashes Immediately After Select US English On First Screen
Mar 15, 2010
When I attempt to install the OS on my PC, the install software crashes immediately after I select US-English on the first screen. I'm copying the entire error report below. My system is configured as follows: Gigabyte P35-DS3R motherboard with 4G RAM. (FYI, I'm using the 32-bit LiveCD just because I may need a 32-bit OS for some purposes. I know this means I may not be able to use all of my RAM.) There are 3 500G hard drives connected to the computer. /dev/sda and /dev/sdb are RAID-1 mirrors via the on-motherboard ICH9R RAID chip. The logical partitions show up as /dev/dm-1, /dev/dm-2, /dev/dm-3, /dev/dm-4, and /dev/dm-5. When I type `fdisk -l`, I can see sda, sdb, and dm-* all separately. (I can provide the full output of `fdisk` if anybody wants to see it.)
/dev/sdc is a standalone drive without RAID.
I want to install Fedora on /dev/dm-2 with swap on /dev/dm-5. Currently, /dev/dm-1 and /dev/sdc2 each contain a separate installation of WinXP. I suspect the problem is with detecting RAID, thus I have deleted most of the error report that doesn't seem to concern storage detection.
[code]....
View 4 Replies
ADVERTISEMENT
Jun 20, 2011
I have a Fujitsu Amilo Pi 3525 notebook with 4 GB RAM and I am trying out Fedora 15 64-bit. When I boot from the CD, it reboots at the point where plymouth should exit and X should start. There are no obvious error messages from the console; it just reboots. Here is the hardware spec. for this laptop: [URL]
This notebook has been generally reliable and runs 64-bit Ubuntu without any problems. I am planning to test the CD in another host (although the media check did not fail) and at least try the 32-bit version (even though I know it can't address of the RAM). As experiences with Linux go, it feels a little early to hit a brick wall so early in the process.
View 3 Replies
View Related
Jun 27, 2011
Two days ago I finally upgraded from Fedora14 (x64) to Fedora15 (x64). [A bit of backstory: I first tried the preupgrade method, I always try it but for some reason it always fails (gives me errors about dependencies that it cannot solve), so as usual I downloaded the full DVD and upgraded using it. It usually works but, as usual, the first time I boot I have to boot in runlevel 3 because after the update my Nvidia drivers aren't up to date with the kernel, so using runlevel 3 I was able to yum update both Kernel and Kmod-nvidia packages; after that I could finally reboot and enjoy the new Gnome3 interface]
When I was finally able to boot in graphical mode (see above), everything worked fine: I had my Gnome3 desktop in front of me, programs worked, all my settings from Fedora14 were still there, all installed programs were still working etc etc. Of course, PackageKit listed a bunch of updates that I needed to do (more than 700 actually), so obviously I gave it the thumbs up to update; unfortunately, some dependencies could not be resolved, to be precise they are dependencies for the packages Mono, RPM and VLC (more details later).......
View 14 Replies
View Related
Mar 24, 2009
i'm using Fecore Core 8, and i'm wondering how to get a package to change my keyboard from English to Hangul/Korean and back to English.
View 5 Replies
View Related
Sep 16, 2009
bug with nautilus 2.26.3? It seems to be an issue on the gnome side rather than on Fedora's side because a Debian bug report has pretty much the same error that I'm getting.
[URL]
View 13 Replies
View Related
Jul 1, 2010
I installed openSUSE 11.2 on my Compaq 2170US laptop. When I select it from the grub menu, everything acts normally until the login screen, which freezes immediately (i.e. before I can select my user account or type in my password).I installed from the full openSUSE DVD and chose the GNOME desktop. Before installing, I took openSUSE for a test drive with the GNOME LiveCD and everything seemed to work fine.
View 4 Replies
View Related
Jan 8, 2011
I have Suse 11.3 KDE and every time I opened an mp3 file, Amarok opened and closed immediately reporting a new bug everytime. So I followed this thread Amarok Not Launching I have uninstalled Amarok through Install/ Remove software. But I am not able to find this folder to delete, as mentioned in above post: Delete the directory ~/.kde/share/apps/amarok
View 9 Replies
View Related
Apr 24, 2011
When I am trying to start Tuxmath, it only show the initial screen for a second or two, and shuts down. From the console I get this error message:
[code]...
View 2 Replies
View Related
Oct 11, 2010
On a fresh install of the Meerkat release candidate, I've installed the latest VirtualBox (3.2.8-64453, not open source version). When I run it, I get a user-agreement notice box as expected.
But, (1) sometimes immediately thereafter, or if not, then (2) as soon as I move the mouse pointer or (3) after I use the PageDown key to get to the bottom of the agreement text and use a key combination for "I agree," my Ubuntu user session crashes and I have to log in again.
The only other weird symptom I'm having is that I cannot set visual effects to anything but "None" (if I attempt to, I get an alert "The Composite extension is not available").
Perhaps there's a video-related problem underlying both issues, i.e., the X server is failing in both cases?
View 9 Replies
View Related
Dec 29, 2010
I am trying to install ubuntu in a machine in which XP was already installed.The GRUB is not displayed and MS Windows is runing immediately after first screen.I installed these drives' mount points
/ as primary
/boot logical
/home logical
I would like to not waste time with experiments, and different tutorials are not clear and coherent about primary , logical and mounting points.
View 2 Replies
View Related
Nov 28, 2008
I'm a fairly new linux user and I seem to have a problem with ubuntu 8.10 after installing it.To make sure everything was working fine before i could do a dual installation, i ran the live cd and it worked like a charm.Everything works fine in the live cd....the internet, sound, graphic drivers (even the special effects seemed to be work fine)I thought wow...after having a bitter experience with Ubuntu 8.04 and 7.10 (I couldnt install those at all coz of driver issues and stuff) I thought this is it!So I used the wubi installer to install ubuntu in my D drive (I didnt wanna use C just to be safe as the primary OS is installed there). Gave it a healthy space of 15 gb. Finished the installation and the rebooted.I went inside Ubuntu which started doing its installation and copying of files and stuff. So far so good.....
And then once it finished its installation and copying of files (100 %), the screen went blank and i see a cursor blinking. I thought maybe its restarting and thats why it must be doing this.I wait for nearly 10 mins and nothings happening except for the cursor blinking on the black screen. I press the caps lock key to see if anything is processing. Nope. So i manually shut it down and then load ubuntu.It loads like 20-30%....rests for a while....and then it loads a bit (not completley)....after that it takes me to a command line asking me for my password and username.I enter those correctly. But it doesnt get me into the main GUI screen yet.
It shows me a lot of the this error msg:
-bash: /dev/null:Permission denied
I'm still in command line (or terminal to be precise). So i use 'startx' (something which i learned from my csci labs ) to start a new session. It showed signs of starting a new session (i can see the mouse pointer and stuff) and then poof....back to the command line again.So I shut it down and load it again in recovery mode. It shows signs of the same symptoms in the splash screen (going very slow after 20-30 % ) and then this time, before i'm asked for my username and password in the command line, it shows a lot of warnings: fake daemon running (or something like that) and i cant even use startx!So i didnt know what to do, uninstalled ubuntu and did a fresh installation (wubi and in the same D drive). Reboot. Install and copy files 100% and then a blank screen again with the dreaded cursor blinking. I still wait for about 10 mins and nothing yet happens. So I manually shut it down (again) and then load ubuntu and unsurprisingly i have the same problem as what i described before....doesnt load properly and i'm not able to come out of the terminal.
View 2 Replies
View Related
Apr 5, 2010
I'm new to Fedora (not linux) and I was wondering how I would go about doing a minimal install of fedora 12. I downloaded the live disc but it doesn't give me installation options (I'm new to minimal installs so I don't know that much). I also searched all over looking for a fedora minimal install iso, something similar to the ubuntu minimal install iso that is only 12mb.
View 14 Replies
View Related
Nov 9, 2009
What happens is that the sound will disappear, either without any apparent reason, otherwise when I move the mouse, or pause vlc, or open up another application, in most cases FF. I have also seen the mouse flash while vlc is in fullscreen, and immediately afterward the sound is gone. When the sound disappears, the gnome-volume-control will disappear and reappear on the top taskbar. Also there will be no device under the hardware and input tab of the sound preferences when the sound disappears.
Killing and restarting the pulseaudio daemon from the cli will return the appropriate choices under sound preferences hardware/input tabs, as well as the audio. This could happen a couple of times in the period of an hour. Usually restarting vlc will solve the problem, or restarting the pulseaudio daemon. Another thing I have noticed is that I will occassionally have to kill the vlc process through the system monitor or cli, as closing vlc will not remove it from the taskbar. I have tried the fix shown here, to no avail. Using kernel 2.6.30.9-96.fc11.x86_64 on a hp dv3-2154ca.
[code]...
View 1 Replies
View Related
Aug 21, 2011
When I try to enable any options in the Debian software, Software Sources immediately crashes. I'd like to enable official supported software downloadable from the internet.
View 3 Replies
View Related
Mar 18, 2010
I'm Dual-booting XP with Ubuntu Karmic Koala, heres my other specs:
CPU: Intel Pentium D 3.0Ghz family(15) model(4) stepping(4)
GFX: Geforce 7800 GT (had problems with GFX when I first installed Ubuntu, I had to update my drivers)
2 GB RAM
This is a nearly fresh install of Karmic Koala, I've only installed whatever updates I needed, graphics card drivers, KPlayer, and Google Chrome. Because I prefer Chrome over Firefox I immediately went to download Chrome, and Firefox would get to the Chrome page and then crash. I then got the Chrome install file from another computer and installed it. Chrome will not even launch, so I go to search the problem in Firefox and it crashes on ANY link I click in Google Search. I also tried to directly type websites into the URL box: it loads the pages title (Ex. "Yahoo! Mail"), and crashes before displaying the page at all.
This is a very odd problem to me as I used the same disc to install dual-boot with Win7 and Ubuntu on my laptop which works perfectly, and now this happens to my desktop.
View 6 Replies
View Related
Feb 28, 2009
I was able to install Fedora 10 from the Live KDE CD, however I can't boot it.
I placed it on /dev/hda4 of an IDE disk, while on /dev/hda1 I have a RedHat 9 Linux, /home is on /dev/hda2 and the swap is on /dev/hda3. I'm not sure if RedHat 9 and Fedora 10 can coexist on the same HD.
There's an option in the Live KDE CD boot install, which allows one to select:
boot from hard disk:
Do you know what to type in in order to direct Fedora to boot from /dev/hda4 (who may be /dev/sda4 as seen by Fedora)?
P.S. For the time being, I want to forget about Grub or LILO and see if I can boot it this way first. I have LILO working, it boots Windows from a separate disk and RedHat 9 from /dev/hda1.
View 3 Replies
View Related
Jan 12, 2009
Installing new Intel server S5000VSA (Sapello) motherboard with RAID 1. Downloaded F10 32 bit DVD and run install. Everything works fine and select Samba and all that. Install completes but on reboot get a blank screen.
I know with Windows one has to load the RAID driver off the Intel driver CD, so guess that is the problem. But how do I do this in Fedora? Question: How do I get to select the Intel RAID driver in the install process? There does not seem to be any place to stop and make this selection. I tried selecting the Red Hat and Suze installs on the Intel configuration assistant but it then reboots and that is it. In Windows it would ask to insert the Intel driver CD but that does not happen. So I am stuck. I loaded Fedora some 3 year ago and like it but then it was not on a RAID setup. I created a VMWare install on my desktop and did the same install options and it works. So the DVD seems fine.
View 3 Replies
View Related
Mar 23, 2010
i can not install contemporary english IDM 2005 on ubuntu there are installation.sh file in linux folder...
i run it on terminal but i can't install.
View 3 Replies
View Related
May 9, 2010
I just installed 10.04 and for some reason once the grub screen loads and I can pick what I want to launch (regular kernel, or rescue mode), it attempts to load and then I just get a blinking cursor. I've found that I can't load the live CD either unless I use the nomodeset flag. I read in another post that this problem should be fixed by editing the /etc/default/grub file to add the nomodeset flag, which I did via nano. However, the file also says you must run update-grub after you edit the file. I tried this and it said something like it can't find / (is /dev mounted?) The hard drive itself is mounted, so I don't know why /dev wouldn't be mounted. How can I get this problem solved so I can boot to 10.04 successfully from the hard drive? (I'm typing this from the live CD right now).
View 9 Replies
View Related
Sep 23, 2010
I am learning japanese and I would like to be able to switch between english and japanese input while keeping an english interface. How would I achieve that? I am using KDE, by the way.
In the Kiten documentation I read that pressing Shift+Space would enable japanese input (built-in in Kiten, according to the documentation). But that does not seem to work in my system.
View 4 Replies
View Related
Mar 7, 2010
I am fairly new to the Linux community however I have done my research on this issue and tried every fix I could think of (registry edits, wine config changes, config.wtf alterations).
All of these things got me where I am today. WoW will run in OpenGL mode for a couple seconds after loading my character and then wine crashes with this error from the Terminal code...
View 2 Replies
View Related
Mar 26, 2009
I'm installing FC-686 onto a Dell 6300 server with several drives, one 300+gig and about 5 9gig drives. The install disk loads fine but when I select install to HD it tells me that there is no device to install to. Obviously doesn't see the HDs. I have used the internal program to format the HDs, I think I selected RAID 3. I wanted to use all the HD space as my data is not critical requiring RAID 5. Unless someone convinces me otherwise. I did this also because I wanted to maximize disk space. What else to do with 9 gig drives?
View 4 Replies
View Related
Apr 3, 2010
Looking for Offline English-English Dictionary for ubuntu.
View 9 Replies
View Related
Feb 3, 2010
I'm trying to make Japanese input work with Scim, but when I modify Locale to make it work, all the menu(pulldown menu, title etc.)also becomes Japanese too. Is there anyway to keep English menus/titles while Japanese(or any other language) input method with SCIM is enabled ?
View 1 Replies
View Related
Dec 23, 2015
I downloaded and mounted debian-8.2.0-amd64-netinst.iso on my work machine's VirtualBox v5.0.12 to check out Debian stable/Jessie's installer and clean installation in case I need to do it soon. I like the new installer compared to 11/24/2011 on my old desktop machine. It is much nicer, fancier with its advanced options, etc.
However, I ran into issues with its "Select and Install" part when I selected desktop managers (e.g., KDE and Gnome) and continued. It failed as shown in [URL] .... images. Why? I tried again from scratch and same thing. If I don't select any and just select non-GUI stuff (e.g, SSH and standard system utilities), then it works but I want the pretty GUI stuff.
View 14 Replies
View Related
Jan 7, 2011
I'm an OpenSuse user wanting to try something different.Ubuntu Studios caught my attention. I had a brief play with an older version a while ago and liked whatI saw.Im having problems installing though.I've downloaded the 32bit version from the studio website link, and burnt the DVD.However the install always fails at the same stage: Select and install software.The error message is not specific, and no more information is given other than the step has failed.Any ideas what could be causing this? Ive tried to burn the DVD several times, on 2 different machines, but no luck so far.
View 8 Replies
View Related
May 6, 2010
I'm running an Acer 1810Tz, dual boot with win7.Under 9.10 and Grub I had no boot issues, however I have just completed the upgrade to 10.04 and upgraded GRUB to GRUB2.Everything boots just fine into Ubuntu, and my GRUB menu looks right, but when I select the Windows 7 option, the machine just hangs with a black screen, white cursor top left. I'm sure this is a trivial problem, something overwritten that shouldn't have been perhaps, but I have no clue where to start.
View 6 Replies
View Related
Mar 29, 2010
I have a older computer that i am trying to load ubuntu on it. I can put in the CD and restart the computer and the boot menu will pop up, I can click any of the options like install ubuntu or anything else but once i click it, it will take me the another screen where it will say loading... please wait then it goes away and i sit there looking at a black screen for 20 minutes while nothing happens. What is wrong why cant i install ubuntu, or anything else except for windows.
View 2 Replies
View Related
Feb 7, 2010
I am having problems with hibernation. When I choose to hibernate, the computer starts to do so, and powers off, and almost immediately it wakes up and comes back to the locked screen. I am using 32 bit version. Hibernate used to work properly on Hardy. I checked that my swap space is more than twice my RAM size.
View 2 Replies
View Related
Sep 28, 2010
I run into a new kind of problem with Ubuntu 10.4 LTS. The unlock screen dialog that asks for your password when resuming from the screensaver does not show up immediately. Moving the mouse, typing stuff. It does not seem to be a pure display problem, since typing the password does not seem to do the trick. After a while (about 15 seconds), it shows up, though.
View 1 Replies
View Related
