Fedora Hardware :: HP 1050 Deskjet All In One - Scanner Not Working
Apr 17, 2011
I can't get the scanner to work. I get this:
[pedroski@fangshan ~]$ scanimage -L
device `v4l:/dev/video0' is a Noname USB2.0 1.3M UVC WebCam virtual device
device `hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW' is a Hewlett-Packard Deskjet_1050_J410_series all-in-one
and this
[pedroski@fangshan ~]$ scanimage -d hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW -T
scanimage: open of device hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW failed: Device busy.
Fedora came with 'Simple Scan' That also returns 'device busy'. Can this scanner work under Fedora? I have tried turning it off, then on. I have rebooted. I have hpijs and hplip installed also hplip-gui. I have put myself in the group lp.
Is there any Linux distribution which supports the mentioned printer out of the box. Tried with Mint 10, I downloaded hplip 3.11.1 and followed instructions on hplipopensource, but OMG it is so complicated..I ran the bash script upon downloading the file. I am unable to install all the needed dependencies. For some it says not installed, When I try to install, it says it is in conflict with some other package and cannot install! I have never struggled so much in installing a printer. I was thinking Ubuntu and Mint are probably the most popular around. I am willing to shift to any distro which supports my printer. Also, scan should work. It is also not getting recognized by Xsane and other scanning apps!
I'm trying to get HP DeskJet 1050 working on Slackware 13.1. When I plug it in to USB I can see it in lsusb. I've installed CUPS started it and went to add printer - but printer is not found. Ok, so I wanted to choose the series I have but 1050 is not listed in HP (is this driver missing?). So I went on to google on it and I got to HP website telling me to install HPLIP. Ok downloaded extracted and ./configure should run but it is not there (automatic script run has no Slackware listed).
I have an old, but still usable, HP Deskjet Plus inkjet printer that I have connected to the parallel port of my Fedora 13 box. I can (apparently) configure the printer using the usual print configuration tools, and have selected the recommend foomatic driver (HP DeskJet Plus Foomatic/pcl3 (recommended)) - but when I try to print the test page the job gets queued and nothing else happens. The jobs simply show as pending in the printer queue.
Current uri is parallel:/dev/lp0.
As a side note, my Epson printer on the USB port works fine, but it's using CUPS + Gutenprint v5.2.6 Simplified. Should I be trying something with a different (e.g. CUPS) driver, or a different way of specifying the foomatic driver, or what?
It's been awhile since I last used my printer in F12. There have been a lot of updates via yum done since whenever that last time was so I don't know precisely which update and when broke things. Attempting to use it today was a no go. It would appear to be a 'udev' issue according to last message logged into /var/log/messages.
My wife's Windows computer is connected to same printer via a parallel cable and it works fine for her so it's not a hardware failure.Consider this solved. Reason for printer failure: Major OP error. The solution was actually rather simple: sudo service cups start
I installed Fedora 12 on a new MacBook with a high def screen resolution (1680 * 1050) using Parallels. When Fedora runs, it run in a small window in the center of the screen - usable but far from desirable. Fedora 12 screen settings do not go as high as 1680 * 1050.
Just acquired a slide/negative scanner (Traveller TV6500) which is reputed only to work under Winderz. Anyone know of a way to get it to run under Fedora 12?
I'm running Linux Fedora-Blue 2.6.32.21-168.fc12.i686 #1 SMP Wed Sep 15 16:25:04 UTC 2010 i686 athlon i386 GNU/Linux lsusb shows Bus 001 Device 019: ID 05a9:1550 OmniVision Technologies, Inc. VEHO Filmscanner
I've tried running it in a VirtualBox Windows XP, but it doesn't appear to work - goes off & churns but doesn't appear to get a picture back.
I got a Visioneer One Touch 9020 USB scanner at a local thrift store and I can't get it working. At the store they said it works. Not tested with Linux. It was only $3 so I figured I'd take the plunge -- proceeds go to local charities. Running sane-find-scanner outputs this:
# sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter.
[Code]...
says no sane devices found, as does the Xsane program when I try to start that. Should I take apart the scanner and see what chip it uses? On a side note, the same thrift store has a Mustek scanner that has only a USB connection, apparently drawing power from the USB bus. But I'm skeptical about this because all the scanners I've seen require 1.25 amps of current and USB provides only 0.5 amps. Has anyone any experience with this scanner and would it be worthwhile to purchase it and try to get it going? I have two scanners that work well with Linux but they are both the multifunction type that copy, scan and print. I'm hoping I can find a regular flatbed scanner. And I should also mention I have Python-imaging-sane installed for flatbed scanners.
I have recently installed Fedora11 and have managed to get the printer side of the above multifunction machine working but not the scanner . The computer recognises the scanner and sane, xsane, sanelib's etc are all installed . When I try to open it it gives the following:
Failed to open device 'brother3:bus5;dev1': Error during device I/O
I was able to get the printer up and running by downloading the printer driver for debian linux (3.1) from the Canon site without any problems.
Unfortunately I am not having the same luck with the scanner.
I tried downloading ScanGear MP for Linux (deb) (1.3) from the same Canon site but have not yet been able to get the XSane Image Scanner to recognize this scanner driver for my Canon.
After clicking on the print option on ms -word, printer does not respond! In the print dialogue box it shows that ink cartridge empty, but even after refilling it, it shows the same status!
I have installed HPLIP and cups found the driver for the printer and all seemed to be setup fine. However when I tried to send a test print, cups showed the job status as stopped. If I try to send anything from Open Office, the page never prints. Not sure where to go from here.
I have just started using puppy linux 5.2 ( lucid) which has transformed my old PC . The only real problem encountered is that I cant get my HP 1050C to print or scan . Running the cups wizard gives me the option of the printer and I found a driver in the list. The table below shows the printer settings being used . Sending jobs or maintenance to the printer has no effect although the cups system says they are complete . Xsane does not see the scanner . The printer functions fine under windows . I am obviously missing something very basic
1. All Cups rpm's 2. Gutenprint-cups 3. All the hplip rpms 4. hpijs
And I still can't get the HP Deskjet F4140 to show up in Selection Window. I have even run HP-Setup and it can't install the F4140 . HP-Setup can see the F4140 is on USB port but can't install it.
I went to the HP website and it says the printer is Supported in the hplip drivers
I have recently acquired me a HP all-in-one printer model HP Deskjet F2483. The printer works fine but am having issues getting the scanner to work. Following instructions I found to Google, this is what my shell looks like:
Code: sh-4.0$ sane-find-scanner # sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter.
I've installed F14 [32 bit] and trying to configure a HP DeskJet 812C on my local netowrk[lpd://192.168.1.35/PASSTHRU] However, the "New Printer" wizard calls KPackageKit that fails and reports, "Could not find printer driver in any configured software source". It is just a dead end!
I have a HP Deskjet 3050 printer. In the past (when i used windows) i installed this printer as a networkprinter. However now in Fedora 15 i cant get it to run.
I had set up a newly purchased HP F4488 using HPLIP, I installed it on my Fedora 10 desktop and it worked fine for the past 2 days. Suddenly, it is failing to print. The scanner works and the photocopier works. When a print job is initialized there is an error and the printer gets disabled.
I have a HP Office-Jet 6110 All-In-One for about 5 years now and I havve been using it on Suse and openSuse without a problem all these years. This morning I wanted to scan something and suddenly realised that the scanner is not working. I can print but not scan. i tried to set up the scanner using YaST like I have done for the past 5 years but it#s not working. Hpaio shows that no scanner is available for this driver. I can#t install the scanner. What has changed in 11.2 that devices that worked before are not working anymore?
Running openSUSE 11.2 with HP All-in-one 3055 printer/fax/scanner attached through network. Using hplip package.
Printer works just fine. Scanner did work for quite some time, however it stopped working after some update about a month ago (using only opensuse update repo).
When doing hp-scan I get following error:
Checking all the logs I can think of I can't figure this one out. Tried newer hplip package fom HP site same issue (I have two systems, on one I've tried the new driver, on one only using opensuse update repo ...both same issue)
I've been trying to get my Epson NX420 printer to scan for about three months now, and I finally got it working. Here's how: 1. Go to [URL] and search for your printer. Select distribution and version and answer a couple of other questions. 2. Download pipslite_1.5.0-2_i386.deb, (or the 64-bit version), and all the iscan*.deb files (again, appropriate to your system). 3. [CRITICAL] Go to [URL] and download this 8.04 package which worked just fine for me on 10.10. 4. Use the Software Center or GDebi or sudo dpkg -i the .debs in this order:
1) libtdl3, which is a dependency for Step 2. 2) pipslite 3) iscan-data 4) iscan-network 5) iscan (If you use a USB connection, you don't need the iscan-network file.) This got my NX420 scanner up and running just fine. Installing libtdl3 was the key; in fact, I used the Debian Lenny package.
I have an Epson CX4300 on Ubuntu 10.10 and I can't get it to scan. I loaded the driver for CX4200 since CX4300 isn't listed in [URL]
sane-find-scanner finds the scanner but scanimage doesn't: ilan@ilan-main:~$ sane-find-scanner -q found USB scanner (vendor=0x04b8, product=0x083f) at libusb:003:002 ilan@ilan-main:~$ scanimage -L
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages).
XSane also reports No Devices available and number 4 in their possible reasons is The backend is not loaded by SANE (man sane-dll). I get: ilan@ilan-main:~$ man sane-dll No manual entry for sane-dll
I do get a man for sane-epson so that hints that the epson driver exists. The fact that sane-dll doesn't seem to exist is probably the problem. I'm using libsane in the Synaptic Package Manager and that is supposed to supply the backends. Should it include sane-dll?
I just installed an all-in-one Brother MFC-8670DN in Ubuntu 9.04. The printing works great but I cannot get the scanner recognized. I tried brscan, brscan2 and brscan3 from the Linux section of the Brother website to no avail. Previously had a lower model Brother MFC working fine. I called Brother and they said that "I need to call Linux for help with the scanner." Anyone who can help with the Brother MFC-8670DN? It would be very much appreciated. This printer may go back to the store if I cannot get the scanner working in Ubuntu 9.04.
I have been given an Epson CX5000 3-in-1 that I only want to use the scanner part of (I have a laser and hate buying ink). The scanner works, tested under windoze, but xsane and scanimage -L fail to find it. But, lsusb does: $ /sbin/lsusb Bus 001 Device 003: ID 04b8:082b Seiko Epson Corp. Stylus DX5050
I saw a post about it under ubuntu that you had to modify /etc/udev/rules.d/45-libsane.rules Which doesn't exist on my Slackware 13 install. I hope this Epson runs faster than my Canon FB630U, which takes almost a four minutes to scan a 5x6 photo and forget scanning an 8.5x11 page (go take a nap).
I was able to get my Epson Stylus NX510 printer up and running (after much issue), but I can't get the scanner working. I'm on a laptop, and the printer/scanner is wifi enabled and broadcasts with its own IP address. I can print with no problem, but xsane and simple scan don't recognize the scanner. I'm running Ubuntu 10.04 Lucid Lynx.
After downloading and installing iscan and run it i see this message:
Could not send command to scanner. Check scanner's status.
After command sane-find-scanner:
And this message is result of scanimage command:
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages).
We recently got an Epson Stylus TX550W Printer/Scanner unit, shared over Wi-Fi with both Windows/Ubuntu PC's, while I have the printing working flawlessly, I don't know where to start to get the scanner working. I've Googled, but haven't come up with much, checked the Ubuntu documentation, apparently Ubuntu (9.10 & earlier, nothing about 10.04) don't automatically detect networked printers, is there a way to get it to recognize without editing config files, which I hate doing? I'm using Ubuntu 10.04 64-bit.
