After clicking on the print option on ms -word, printer does not respond! In the print dialogue box it shows that ink cartridge empty, but even after refilling it, it shows the same status!
View 1 RepliesI have Ubuntu version 10.10 and I'm trying to install the HP DeskJet 1000 J110a printer. I have HPLIP version 3.11 (the latest version I believe). The printer shows up but when I try to print the error message reads: Printer requires the 'foomatic-rip-hplip' program but is not currently installed.
View 2 Replies View RelatedWhen I go to System->Administration->Printing no window pops up. Down on the bottom panel it says "Starting Printing" and then goes away. I'm trying to install my HP Deskjet printer,
View 3 Replies View RelatedMy HP Deskjet D-2660 will not print. I can print to file but not the printer. I am running Ubuntu 10.04 and have no other problems. I have installed hpip and hpijs form HP and cups was made available via and upgrade. I have a lot of data from var/log/cups/error_log but don't know what it is supposed to say.
I can print to file and everything else I check seems to say that all is right. Is there any glaring faults that I should look for?? As I stated on the other post I get a message that the print job has been sent to the printer and then another message stating that the print job has completed. In system/administration/printing, the printer shows up properly and has a green check mark on it. Connected to localhost shows at the bottom of the little window. Under /printer it shows shared and enabled Then under printer/properties, it shows as the HP Deskjet D2600 series the location is given as john-desktop It defines the Device URI: hp:/usb/Deskjet_D2600_series?serial=CN9ANDF0ZT05C9 shows the Make and Model HP Deskjet d2600 Series hpijs,.. printer state: idle
Across the bottom it theoretically allows you to print a test page or clean the print heads. (won't print) On the printing-local host small page that opens under system/administration/printing there is no group under that heading only new group or new group from selection. I never named a group since I am the only user.
I have shut the printer down and disconnected the USB and rebooted. Then connect the power and plug in the USB cable I get all the same answers nothing appears to change. Here is some of the var/log/cups/error_log file. It does this over and over every minute same thing. The print que is empty from both administration and applications.
[Code]....
I installed the Printer, but Xsane does not recognize the scanner, how can i acivate the scanner. my system is Debian Lenny 507 Kde i386. I have looked through the posts in the forum, but found nothing that can help me. can somebody point me in the right
View 14 Replies View RelatedUbuntu 1010 64bit
HP Deskjet 5740 USB interface
The printing has been running without problem ever since the installation of this box at least >1 year. Today I found it stop working with following warning:
Code:
Filter /usr/lib/cups/filter/hpcups for printer Deskjet-5700 not available
I'm running a standard 13.1 32 bit install with an HP deskjet 990C, run off of USB. Until today everything has printed properly. Now nothing prints. Nothing has been installed unless it came through slackpkg, and yes it is still on the correct setting for arch and revision. CUPS shows printer as installed, accepting jobs an idle. No error messages are appearing but nothing is reaching the printer. The info I can glean is from the error logs in CUPS:
[Code]....
I have recently acquired me a HP all-in-one printer model HP Deskjet F2483. The printer works fine but am having issues getting the scanner to work. Following instructions I found to Google, this is what my shell looks like:
Code:
sh-4.0$ sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
[Code]...
I want to install printer HP Deskjet k209 in Debian Lenny but i am unable to install because printer driver is not available in this distribution..
View 2 Replies View RelatedI'm trying to install hp DeskJet 6500 printer on a network.
My Centos version is
Linux xxxxx 2.6.18-194.26.1.el5xen #1 SMP Tue Nov 9 13:35:30 EST 2010 x86_64 x86_64 x86_64 GNU/Linux
Ofcourse My printer model is not showing up on the list of printer list when using ipp based configuration.
so while searching around, I came across article to install hplip at
[URL]
and I tried to install the following hplip version with centos.
[URL]
Running the configure with following arguments
./configure --with-hpppddir=/usr/share/ppd/HP --libdir=/usr/lib64 --prefix=/usr --enable-qt4 --enable-doc-build --enable-cups-ppd-install --disable-foomatic-drv-install --disable-foomatic-ppd-install --disable-hpijs-install --disable-policykit --disable-cups-drv-install --enable-hpcups-install --enable-network-build --enable-dbus-build --enable-scan-build --enable-fax-build
I get following error
configure: error: cannot find net-snmp support (or --disable-network-build)
But net-snmp is installed on my system, so, I tried with disable-network-build and tried to get around the problem, the next error I get is
checking for usb_init in -lusb... no
configure: error: cannot find libusb support
I have problem with my printer HP Deskjet D1460. My printer is configured and works. When I send a file on the print, the printer clings a sheet of paper and starts to print, but a paper as was clean so clean and remains, after printing.
View 2 Replies View RelatedI have installed HPLIP and cups found the driver for the printer and all seemed to be setup fine. However when I tried to send a test print, cups showed the job status as stopped. If I try to send anything from Open Office, the page never prints. Not sure where to go from here.
View 4 Replies View RelatedI have an old, but still usable, HP Deskjet Plus inkjet printer that I have connected to the parallel port of my Fedora 13 box. I can (apparently) configure the printer using the usual print configuration tools, and have selected the recommend foomatic driver (HP DeskJet Plus Foomatic/pcl3 (recommended)) - but when I try to print the test page the job gets queued and nothing else happens. The jobs simply show as pending in the printer queue.
Current uri is parallel:/dev/lp0.
As a side note, my Epson printer on the USB port works fine, but it's using CUPS + Gutenprint v5.2.6 Simplified. Should I be trying something with a different (e.g. CUPS) driver, or a different way of specifying the foomatic driver, or what?
It's been awhile since I last used my printer in F12. There have been a lot of updates via yum done since whenever that last time was so I don't know precisely which update and when broke things. Attempting to use it today was a no go. It would appear to be a 'udev' issue according to last message logged into /var/log/messages.
My wife's Windows computer is connected to same printer via a parallel cable and it works fine for her so it's not a hardware failure.Consider this solved. Reason for printer failure: Major OP error. The solution was actually rather simple: sudo service cups start
I can't get the scanner to work. I get this:
[pedroski@fangshan ~]$ scanimage -L
device `v4l:/dev/video0' is a Noname USB2.0 1.3M UVC WebCam virtual device
device `hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW' is a Hewlett-Packard Deskjet_1050_J410_series all-in-one
and this
[pedroski@fangshan ~]$ scanimage -d hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW -T
scanimage: open of device hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW failed: Device busy.
Fedora came with 'Simple Scan' That also returns 'device busy'. Can this scanner work under Fedora? I have tried turning it off, then on. I have rebooted. I have hpijs and hplip installed also hplip-gui. I have put myself in the group lp.
I've bought a HP Photosmart printer, HP Photosmart wireless e-All-in-One printer - B110a and i've got a problem installing it properly. I'm using Debian 6.0 Squeeze. When i connect the printer, Debian doesn't recognize my printer as the Photosmart B109 printer for unknown reason. When i go to the site of HP and search for a driver, it directs me to this site:I've downloaded that latest hplip file as a .run file and installed it. My printer is recognized proparly, but when i try to print a colored image, it comes out black/white. Something is not crrect. Does anyone recognize this problem with this type HP printer?
View 7 Replies View RelatedI just upgrade to Fedora 11.
I have problem in installing the printer, no matter add printer in local network or Windows Printer via Samba.
The summary is as follow:
I have download a printer driver and had installed but got error when I tried to printer a test page.
I have been using the Lucid since about Xmas time as my main Distro. Up until Sunday when I did a fresh Install of Lucid 10.4 final release my epson printer was working, now it isn't even listed in the printer list, but it is still found with lsusb.
View 3 Replies View RelatedI have an HP Desk Jet F380 printer that no longer seems to work since I upgraded from Hardy to Lucid. I don't even see any options to change printing preferences when I go into System > Administration. I'm not sure what to do at this point?
View 1 Replies View RelatedI have noticed since I have updated to 10.04.3 this has been coming up in my boot log.
udevd[249]: SYSFS{}= will be removed in a future udev version, please use ATTR{}= to match the event device, or ATTRS{}= to match a parent device, in /etc/udev/rules.d/85-brltty.rules:23
Also my printer has quit working also, have tried reinstalling cups, reinstalling the print drivers printer still does not work.
Does this entry in the the boot log have anything to do with the printer?
After upgrading to 9.10 HP Printer C7200 is recognized but doesn't work. get message ""printer State" Idle-/usr/lib/cups/backend/upfailed Have tried to rectify without success. as a lot of my use of Ubuntu depends on usable printer.
View 3 Replies View RelatedI'm running Ubuntu 10.04, and after installing the recommended updates yesterday, my printer, which was working perfectly, no longer works. I tried reinstalling it by downloading the appropriate driver, but it still won't work. Here is the error log:
D [06/Jul/2010:07:55:26 -0400] cupsdSetBusyState: Dirty files
D [06/Jul/2010:07:55:26 -0400] cupsdReadClient: 12 POST / HTTP/1.1
D [06/Jul/2010:07:55:26 -0400] cupsdSetBusyState: Active clients and dirty files
D [06/Jul/2010:07:55:26 -0400] cupsdAuthorize: No authentication data provided.
[Code].....
I had it printing until the last cups upgrade. Brother support thinks it is something to do with the upgrade. We did a reinstall of the printer driver. The printer works on Virtual Box and the scanner works on Ubuntu, but not the printer. What do I need to have the printer work under 11.04?
View 9 Replies View RelatedI have a Epson stylus T11 printer. It used to work fine with Ubuntu 9.04. After I upgraded my OS to 10.04, it is not working.
Here is my output.
It says its printing but doesnot print anything. I have tried a lot of forums including LQ, but no solutions.
The lsusb command gives me the follwing:
I have been using epson stylus T11 printer on ubuntu 9.10 for about six months, but after I upgraded it to 10.04, the printer is not working properly. It is working fine with other distributions.
View 1 Replies View RelatedI tried to install a lexmark z1300 printer, but ubuntu did not recognize it and it crashed. I got a blank screen with a cursor in the middle of the screen that was not flashing. I tried "ctrl + alt +backspase" and it did not work so i had to turnoff the computer by hand. After i turned it back on, i could no longer use vlc player. When i tried to open an .avi file i got the message shown below and i could only hear the audio. I tried to reboot with the option to repair broken packages and that only messed up my window borders (i.e. i had no option to min max or close the windows). The window border problem was solved by just rebooting the computer but vlc media player still does not work.
MESSAGE FROM VLC PLAYER: No suitable decoder module: VLC does not support the audio or video format. Unfortunately there is no way for you to fix this.
I upgraded from Karmic to Lucid RC a couple of days ago and have been trying to work through a few problems since. One of these problems is printing with my Brother DCP506CN printer which was working in Karmic. However, I just can't seem to get it going in Lucid. I have followed the Brother linux install procedure, which worked for the the last few Ubuntu releases, but not for this one it seems.
View 3 Replies View RelatedI'm a newcomer to Ubuntu. Have struggled with 9.04 and managed to get my Canon MP620 to work in that version. Now I have upgraded to 10.04 and have problems to get my printer to work again.
View 7 Replies View RelatedI've been trying to get my Epson NX420 printer to scan for about three months now, and I finally got it working. Here's how:
1. Go to [URL] and search for your printer. Select distribution and version and answer a couple of other questions.
2. Download pipslite_1.5.0-2_i386.deb, (or the 64-bit version), and all the iscan*.deb files (again, appropriate to your system).
3. [CRITICAL] Go to [URL] and download this 8.04 package which worked just fine for me on 10.10.
4. Use the Software Center or GDebi or sudo dpkg -i the .debs in this order:
1) libtdl3, which is a dependency for Step 2.
2) pipslite
3) iscan-data
4) iscan-network
5) iscan
(If you use a USB connection, you don't need the iscan-network file.) This got my NX420 scanner up and running just fine. Installing libtdl3 was the key; in fact, I used the Debian Lenny package.
after looking around for hours, i finally gave up and decided to write this post. I need to know exactly what to do to get my canon mx860 printer connected to ubuntu wireless. ive tried nearly everything, but nothing really makes sense and it just doesn't work.
View 1 Replies View Related