Hardware :: HP 1050 J410 Deskjet All In One Support
Mar 7, 2011
Is there any Linux distribution which supports the mentioned printer out of the box. Tried with Mint 10, I downloaded hplip 3.11.1 and followed instructions on hplipopensource, but OMG it is so complicated..I ran the bash script upon downloading the file. I am unable to install all the needed dependencies. For some it says not installed, When I try to install, it says it is in conflict with some other package and cannot install! I have never struggled so much in installing a printer. I was thinking Ubuntu and Mint are probably the most popular around. I am willing to shift to any distro which supports my printer. Also, scan should work. It is also not getting recognized by Xsane and other scanning apps!
I'm trying to get HP DeskJet 1050 working on Slackware 13.1. When I plug it in to USB I can see it in lsusb. I've installed CUPS started it and went to add printer - but printer is not found. Ok, so I wanted to choose the series I have but 1050 is not listed in HP (is this driver missing?). So I went on to google on it and I got to HP website telling me to install HPLIP. Ok downloaded extracted and ./configure should run but it is not there (automatic script run has no Slackware listed).
I can't get the scanner to work. I get this: [pedroski@fangshan ~]$ scanimage -L device `v4l:/dev/video0' is a Noname USB2.0 1.3M UVC WebCam virtual device device `hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW' is a Hewlett-Packard Deskjet_1050_J410_series all-in-one
and this [pedroski@fangshan ~]$ scanimage -d hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW -T scanimage: open of device hpaio:/usb/Deskjet_1050_J410_series?serial=CN0CN3H3CZ05HW failed: Device busy.
Fedora came with 'Simple Scan' That also returns 'device busy'. Can this scanner work under Fedora? I have tried turning it off, then on. I have rebooted. I have hpijs and hplip installed also hplip-gui. I have put myself in the group lp.
I have just started using puppy linux 5.2 ( lucid) which has transformed my old PC . The only real problem encountered is that I cant get my HP 1050C to print or scan . Running the cups wizard gives me the option of the printer and I found a driver in the list. The table below shows the printer settings being used . Sending jobs or maintenance to the printer has no effect although the cups system says they are complete . Xsane does not see the scanner . The printer functions fine under windows . I am obviously missing something very basic
I installed Fedora 12 on a new MacBook with a high def screen resolution (1680 * 1050) using Parallels. When Fedora runs, it run in a small window in the center of the screen - usable but far from desirable. Fedora 12 screen settings do not go as high as 1680 * 1050.
I seem to be having on going issues with my printer. I was able to print a garbled test page but I get a result from terminal of printer HP-Deskjet-f2400 now printing HP-Deskjet-f2400-0. enabled since Mon May 31 15:45:04 2010 Connecting to printer... and it just sits there. Nothing is in error with the printer itself though.
I recently installed Ubuntu 10.04 on my computer. Everything works except for my HP Deskjet D2660 printer. The printer is recognized, but it will not print. HP-check shows no errors or warnings. The printer works fine on another computer with Ubuntu 9.10
I tried setting up my printer, HP Deskkjet D2660, using CUPS. I enabled the CUPS service and configure the printer through it. But when I try to test print, my printer wont print. Now, i tried to look at the net for possible answer and somewhere, I read that my printer needs the newer version of hplip than the one included with the default slackware 13.0 install.
1. Do i really need to update hplip just to make my printer work? Do anyone uses the same printer model and make it work without updating the said package?
2. If i really have to update it, is there any Slackbuild script I can use to make the hplip-3.10.6.tar.gz into slackware package? I prefer creating package than installing using make.
We recent got this printer as the three others are old, hard to maintain, and don't work. However, there's been no end of trouble. We've had to initially install it under Windows, which is no trouble. Intending to put it to wireless use, I've hit a problem. The HP printer tool in Slackware 13.0 claims that CUPS either isn't installed (which it is) or isn't running (which it is)
So I kept it on USB and shared it, providing yet more trouble. Slackware again seems to have trouble with CUPS (using the Printing tool from GSB). Now, Ubuntu Jaunty, the other Linux on the network, can see this printer, but doesn't have a driver for it, meaning it can't use it.
What I'd like to do is switch it to wireless. I can do that, but I don't know what to install on the two Ubuntu PCs to get the HP printer tool, or if on Jaunty, it still needs to be given the drivers for it, and on Slackware, CUPS is the problem (Though may be solved with an install of something else before long)
I updated to the recent 9.10 version of Ubuntu and found that my printer no longer works. When trying to print, the printer just blinks and *occasionally* makes a noise and prints out a partial line of text or whatever. It's a USB connecting HP Deskjet D1420 that is not a network printer and does not need to be networked.
I have spent a few hours on this, trying various combinations of instructions. The nearest I got was when I followed the instructions from the HPLIP site, but it ended up with telling me some dependencies were not installed. I installed them using the Mintinstall tool, but still no go.
Before I spend any more time on this, I would like to know if there is a user out there who has got this particular printer to run on the Mint 7 distribution? If somebody has, then I know it is at least possible, and I will persevere!
The printing has been running without problem ever since the installation of this box at least >1 year. Today I found it stop working with following warning: Code: Filter /usr/lib/cups/filter/hpcups for printer Deskjet-5700 not available
I have installed HPLIP and cups found the driver for the printer and all seemed to be setup fine. However when I tried to send a test print, cups showed the job status as stopped. If I try to send anything from Open Office, the page never prints. Not sure where to go from here.
I am attempting to install my hp Deskjet D1660 printer and I am getting a dependency error that states I am in need of the GNU gcc C+ or C++ compiler. I know I have the latest gcc compiler installed on my system already. I am running SUSE 11.3.
Code: warning: Missing REQUIRED dependency: gcc (gcc - GNU Project C and C++ Compiler) warning: This installer cannot install 'gcc' for your distro/OS and/or version. error: Installation cannot continue without this dependency. Please manually install this dependency and re-run this installer.
Code: # zypper install gcc Loading repository data... Reading installed packages... 'gcc' is already installed. No update candidate for 'gcc-4.5-4.2.i586'. The highest available version is already installed. Resolving package dependencies...
I'm using a HP Deskjet F380 multifunction printer on a ubuntu 9.1 machine. It recognises it as an F300 series printer and so far it prints and scans very well. The problem is that I usually print 2 pages per sheet and double side on windows but I cannot do it on linux (in this case the option of printing odd pages first and even pages second is useless). I see there is an option in your printer preferences to print double side but it doesn't work.
OS: Ubuntu 10.10 I've been trying to get my HP DeskJet D2660 printer to work for a while now, but I am having several problems that I can't seem to get around. For the driver I have 2 options. The hpijs (hplip) or the hpcups driver. Neither of them work properly.
The HPLIP driver and control software keeps telling me that the stuff I print has printed correctly, but my printer does nothing. It just sits there laughing at me whilst I get popups on my monitor telling me that the print job start and completes. I have successfully printed the print head calibration paper and aligned them as told by the HP software, but after I have done so, it just goes back to sleep. Nothing prints, not even the test page. I can't understand why it prints the calibration sheet just fine and then, afterwards, it won't print anything else but tells me everything prints fine.
The HPCUPS driver works just fine, but it has these really bad shadows on everything I print caused by incorrect alignment of the print heads. There seems to be no option of correcting this using the HPCUPS driver. So, what I have is a HPLIP driver which allows me to calibrate but won't print, and a HPCUPS driver which prints just fine, but won't allow me to calibrate. My HPLIP driver version: 3.10.6 (official from Ubuntu) I've also tried downloading and installing the latest (3.10.9), but with no luck. Prints calibration just fine, then nothing else.
I'm running a standard 13.1 32 bit install with an HP deskjet 990C, run off of USB. Until today everything has printed properly. Now nothing prints. Nothing has been installed unless it came through slackpkg, and yes it is still on the correct setting for arch and revision. CUPS shows printer as installed, accepting jobs an idle. No error messages are appearing but nothing is reaching the printer. The info I can glean is from the error logs in CUPS:
I installed the Printer, but Xsane does not recognize the scanner, how can i acivate the scanner. my system is Debian Lenny 507 Kde i386. I have looked through the posts in the forum, but found nothing that can help me. can somebody point me in the right
It's been awhile since I last used my printer in F12. There have been a lot of updates via yum done since whenever that last time was so I don't know precisely which update and when broke things. Attempting to use it today was a no go. It would appear to be a 'udev' issue according to last message logged into /var/log/messages.
My wife's Windows computer is connected to same printer via a parallel cable and it works fine for her so it's not a hardware failure.Consider this solved. Reason for printer failure: Major OP error. The solution was actually rather simple: sudo service cups start
I have an old, but still usable, HP Deskjet Plus inkjet printer that I have connected to the parallel port of my Fedora 13 box. I can (apparently) configure the printer using the usual print configuration tools, and have selected the recommend foomatic driver (HP DeskJet Plus Foomatic/pcl3 (recommended)) - but when I try to print the test page the job gets queued and nothing else happens. The jobs simply show as pending in the printer queue.
Current uri is parallel:/dev/lp0.
As a side note, my Epson printer on the USB port works fine, but it's using CUPS + Gutenprint v5.2.6 Simplified. Should I be trying something with a different (e.g. CUPS) driver, or a different way of specifying the foomatic driver, or what?
I'm an happy user of 11.2 but I've a weird and very annoying problem with my old but still good for me hp 710c Printer.
I should say that I have this problem on with 11.2 because printer runs well either on windows or with other linux distro.
the problem is that when I try to print anything I get: /usr/lib/cups/filter/foomatic-rip failed
I've found an other thread (11.2 - Cups ends /usr/lib/cups/filter/foomatic-rip failed - openSUSE Forums) regarding the same problem but with 11.2 milestone 1 and the solutions seemed to be to downgrade to an older cups and ghostscript version.
I can't print via our network printer (HP DeskJet 3650) which is connected to a WinXP PC on the network. My laptop is wireless connected to the network. My distribution is openSUSE 11.2 and I tried setting up the network printer via CUPS:
Went to http://localhost:631 Add Printer Device: Windows Printing via SAMBA Device URI: smb://UMBRELLA/SMOKE/HP3600 Make: HP Model: HP DeskJet 3650, hpcups 3.9.8 (en) Printer State: idle, accepting jobs, published.
Then clicked the "Print Test Page" button. At this point the printer actually starts making sounds.. the same sounds it makes when it's preparing to print something. But then, it stops. The printing job is still present in the printer queue at the WinXP PC, but it won't print.
So I looked at this documentation: [URL]
Step 2 from this documentation tells me to install a PPD file.. which I can't find anywhere. It's not on the original HP driver CD, neither can it be downloaded from this page: http://www.openprinting.org/show_pri...P-DeskJet_3650.
My HP Deskjet D-2660 will not print. I can print to file but not the printer. I am running Ubuntu 10.04 and have no other problems. I have installed hpip and hpijs form HP and cups was made available via and upgrade. I have a lot of data from var/log/cups/error_log but don't know what it is supposed to say.
I can print to file and everything else I check seems to say that all is right. Is there any glaring faults that I should look for?? As I stated on the other post I get a message that the print job has been sent to the printer and then another message stating that the print job has completed. In system/administration/printing, the printer shows up properly and has a green check mark on it. Connected to localhost shows at the bottom of the little window. Under /printer it shows shared and enabled Then under printer/properties, it shows as the HP Deskjet D2600 series the location is given as john-desktop It defines the Device URI: hp:/usb/Deskjet_D2600_series?serial=CN9ANDF0ZT05C9 shows the Make and Model HP Deskjet d2600 Series hpijs,.. printer state: idle
Across the bottom it theoretically allows you to print a test page or clean the print heads. (won't print) On the printing-local host small page that opens under system/administration/printing there is no group under that heading only new group or new group from selection. I never named a group since I am the only user.
I have shut the printer down and disconnected the USB and rebooted. Then connect the power and plug in the USB cable I get all the same answers nothing appears to change. Here is some of the var/log/cups/error_log file. It does this over and over every minute same thing. The print que is empty from both administration and applications.
I have recently acquired me a HP all-in-one printer model HP Deskjet F2483. The printer works fine but am having issues getting the scanner to work. Following instructions I found to Google, this is what my shell looks like:
Code: sh-4.0$ sane-find-scanner # sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter.
I was trying to print my resume and a job application with my printer and it was coming out red (I now know how to fix that) but I decided to install the hp linux printer driver and it picked up my printer installed everything for it (its a hp deskjet f2100 series) and now it wont print ! I've got a troubleshoot.txt file for any technical info if you need it. (I had to compress it but its a 80 kb text file).
I recently installed 10.04 and the printer was working for a while. Now when I print something the print que icon shows up and goes out like it has printed but nothing prints. I ran the troubleshooter and got this.
I had set up a newly purchased HP F4488 using HPLIP, I installed it on my Fedora 10 desktop and it worked fine for the past 2 days. Suddenly, it is failing to print. The scanner works and the photocopier works. When a print job is initialized there is an error and the printer gets disabled.
I've installed F14 [32 bit] and trying to configure a HP DeskJet 812C on my local netowrk[lpd://192.168.1.35/PASSTHRU] However, the "New Printer" wizard calls KPackageKit that fails and reports, "Could not find printer driver in any configured software source". It is just a dead end!