just upgrade from F13 to F14 and i got this error messager is startup
Quote:
ImportError: /usr/lib/python2.7/site-packages/ixf86configmodule.so: undefined
symbol: xstrtokenize
and from /var/log/Xorg.0.log
Quote:
(II) LoadModule: "fglrx"
dlopen: /usr/lib/xorg/module/drivers/fglrx_drv.so: undefined symbol: savedScreenInfo
(EE) Faild to load /usr/lib/xorg/module/drivers/fglrx_drv.so
[Code].....
I have Fedora 10 installed. I've just made an update of my system. Things that were updated were a new kernel version with devel and also something with NVIDIA (which is my video card).
After restart of my system, compiz fusion no longer works.
I have a NVIDIA-Linux-x86-177.82-pkg1.run -file to manually install the NVIDIA-driver so the advanced features of Compiz can be utilized.
After install, the bootup screen tells me that loading the NVIDIA driver has failed. I also receive a WARNING-message.
I have set this up before (ie installed the drivers and had them working perfectly) but had to do a system wide re-install of fedora. Since this clean install, I've had non-stop grief with nVidia drivers. They have been downloaded and installed via yum, and on start-up nvidia.ko loads. But from with gnome I cant gain access to any 'special effects' (ie desktop effects wont enable).
View 4 Replies View RelatedI had to have the Nvidia Driver build a module to my kernel. It goes through, says it was successful, but I an unable to start X and get this log:
Quote:
X.Org X Server 1.6.1.901 (1.6.2 RC 1)
Release Date: 2009-5-8
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.18-128.1.6.el5 i686
[code]....
Its an Nvidia 8200 integrated graphics card... Not sure if there is a wrong driver or the driver is in a different location then where Fedora is looking.
I used leighs post to install the nvidia driver for Fedora 12 and now plymouth does not work it uses the text theme. Right before it goes into the text theme I get this message:
"Unknown boot option `nouveau.modeset=0' : ignoring"
To use games and other intensive applications, but with the switch I completely lost control of the brightness for the monitor. Is their a way to configure that, through the terminal or external application. If not, is there an experimental 3d version of nouveau I could try. Help would be appreciated, everything else works great so far.
View 2 Replies View Relatedi upgraded my System from Fedora 11 to Fedora 13. My graphics driver crashed (graphics-card: radeon hd-4-series) and i couldn't even start. I managed to reset the driver and now Fedora ist booting again, but it isn't working properly:
Code:
And every time is boot, i get this boot-message:
Code:
I installed CentOS 5.5 64-bit version. After (and during) the installation my graphic card couldn't be recognized. The resolution was way below the native (1920*1080), windows moved pretty slowly and scrolling was even slower.I updated the system - didn't solve the problem. After the update I tried to select the 'radeon' driver from Administration->Display, but after the restart the X server crashed and recovered to the previous configuration (vesa). I tried to install the official AMD Catalyst driver, and after the restart the native resolution was detected, but the interface begun to work even slower (very difficult to move windows and scroll text). The Catalyst control panel couldn't be opened as well.
View 4 Replies View Relatedget multiple screens working in Xorg with the Intel driver? I can manage to get Dual Head working (one big screen), but I'm interested in having two seperate X sessions (two screens) instead.
View 1 Replies View RelatedThe Fedora 14 (and 13) pwc Philips Webcam Driver.is only supporting 160x120 resolution (and nothing higher such as 640x480). Also not supporting some other things correctly, I suspect.I say so having tested multiple web camera software and either they don't work (because they have no setting for low res) or they do work if settable to low res., but not for any higher res.I also have a working setpwc tool which shows the driver does not support framerate resetting.I have a Toucam and Toucam Pro - same for both.Also these units worked fine under Fedora 11, and under earlier versions even Red Hat 4.But I usually got the latest pwc from Saillaird.org and compiled it to get full support but there are no more current sources there anymore, and the older ones don't compile.But as I am saying under F11 it was fully correct, now under F13 and 14 it is broken.
View 14 Replies View RelatedI am using the akmod nvidia driver and I have the option for "sync to vblank" checked, however when running minecraft my computer is still pulling 200+ fps and it's causing tearing like a beast.Is anyone else having this problem? I don't know if my drivers are corrupted, set up improperly, or if the driver is just broken.
View 1 Replies View RelatedI recently installed realtek sound driver software in my system,
but after installing it,the speakers are not working....
I'm using fedora 13(x86_64).
i just want to make my system speak,like before....
how to make my speakers work ?
I installed it on a Dell Inspiron 531 with the GeForce 6150SE nForce 430 built in video card. From the recommend driver list I installed �NVIDIA accelerated graphics driver (version current) [Recommended
Well, turns out it should not have been recommended. I had restarted and all I got was a low res ubuntu logo and a boot right into a full screen terminal. Tried startx and got a no screens found, I look online for about an hour last night and decided to just reinstall, which takes a couple hours when installing all the packages.
I have done more research today and found to install the latest linux x64 driver from nVidias website, which I did, but it does not run. I followed some more instructions and it said to do a �sudo chmod +x <file>� which I did, and it starts to open and I get �You appear to be running an X server; please exit X before installing.�
I�m starting to get a little frustrated here, guess I�m just used to a lot of the ease of windows and assumed that something like installing a graphics card driver would be easy.
In lmms there is no sound and it says:
No audio-driver working - falling back to dummy-audio-driver
in the command prompt. Sound works everywhere else just not lmms.
This is my first attempt with Yum and Fedora for that matter. I need to load a print driver and network driver for an MX860 printer. I downloaded the drivers and they are in the download folder. When I try to install I get what is below. How do I resolve? Do I need to identify where the driver is? If so, how?
[compaq@compaq ~]$ su -c'yum install cnijfilter-mx860series-3.10-1-i386-rpm.tar.gz'
Password:
Loaded plugins: refresh-packagekit
updates/metalink | 15 kB 00:00
Setting up Install Process
No package cnijfilter-mx860series-3.10-1-i386-rpm.tar.gz available.
Nothing to do
[compaq@compaq ~]$
recently switched from Ubuntu. But I'm finding it difficult to get my wireless card working. It's a Dell Wireless 1395 Wlan Mini card, but works with a broadcom driver(Ethernet card is a broadcom).
View 2 Replies View RelatedIn my laptop on Linux(Ubuntu) platform the Wifi driver is not working so.. What should I do ?
View 2 Replies View RelatedI am using my ATI Radeon 9550 display card but just can't adjust it to 1920x1080 resolution in ubuntu 9.10. I can't even start ATI Catalyst Control Center and i believe there is something wrong with the driver. When i try to start ATI Catalyst this message pop up "There was a problem initilizing Catalyst Control Center Linux edition. It could be caused by the following. No ATI graphics driver is installed, or the ATI driver is not functioning properly. install the ATI driver appropriate for you ATI hardware, or configure using aticonfig."
Everything works fine in Ubuntu 8.10.
I just deleted my windows XP and installed Ubuntu 9.10 earlier this morning. I used wired connection to get drivers for my wireless network card.
When I did lspci, the very last line states:
Network Controller: Broadcom Coporation BCM4311 902.11b/g WLAN(rev 01)
I used the System -> Administration -> Hardware Driver and found 2 drivers. I have tried them both to connect to my D-Link Router. Neither of which worked.
For Broadcom B43 Driver, the wireless is able to detect wireless networks. However, it fails to establish connection.
For Broadcom STA Driver, the wireless cannot even detect wireless networks available.
What is the issue here and how do I resolve it so that I am able to connect onto the internet wirelessly?
i have just installed Ubuntu 10.04 LTS on my Dell XPS M1530. Previously, i got the bcmwl proprietary driver to work when i was trying the live cd. for some reason, when i installed it however, it did not work the same. when ubuntu booted when i installed it, it did not sense the proprietary driver. so i went in to the ubuntu disc itself and got the bcmwl driver and the dkms packages. so i try to install both of them with dpkg -i as root. dkms installed successfully, however, the bcmwl driver gave me this:
root@Ryan-PC:/home/ryan/Desktop# dpkg -i bcmwl-kernel-source_5.60.48.36+bdcom-0ubuntu3_i386.deb
(Reading database ... 122807 files and directories currently installed.)
Preparing to replace bcmwl-kernel-source 5.60.48.36+bdcom-0ubuntu3 (using bcmwl-kernel-source_5.60.48.36+bdcom-0ubuntu3_i386.deb) ...
[Code]....
Since the last driver error I had posted the thread was starting to drift WELL off the original issue so now I am opening a new thread since it IS a whole different problem in general;So, I was having issues with my driver not being enabled. After I installed it manually it appeared to be correct how-ever when I ttried to enable special effects, and compiz, it didn't work.And even after a correct installation of the driver some windows when they pop up look like static then appear.Graphics card is an:nVidia 6150SE onboard card.I know it can handle compiz, and effects, because it did before on the other version of ubuntu I had.
View 5 Replies View RelatedPretty self explanatory, I can't get the NVidia driver to work with my laptop's 310M. And yes I have tried both steps in .64&postcount=9, but to no avail. The two error messges I'm seeing are "(EE) No devices detected." and "Fatal server error: no screens found".
View 3 Replies View RelatedWas having an xorg problem earlier now resolved but now the screen is extremely unstable and bouncing. I checked my ATI Fire GL driver and it is installed and working fine.
Is there a CLI I can enter and see the issue or perhaps 10.10 and my drivers are conflicting?
EDIT: I see in synaptic I have nvidia drivers and something called a nouveau display driver. Can I remove those since I run an ATI card?
I've got a friend who, after experiencing the horrors of Vista and me telling of the wonders of Linux, decided to switch. However, her Wifi is not working. I typed in 'lspci -nn', and it seems that two things came up; a Broadcom BCM4401 and an Atheros AR2413. Does the computer have two Wifi cards? Which do I need the driver for, or both? Which brings me to my second question; where do I find and how do I install a driver?
View 7 Replies View Relatedmy laptop is ASUS U41JF with Intel Core i3-380M and nVIDIA GeForce GT 425M, everything on my Slackware64-current is fine except the video driver.I have tried both ways:1. Packages from Slackbuild(260.19.29)2. Driver from nvidia offical website(260.19.36)Both methods fails because the screen turns black when I set nvidia driver in xorg.conf ans start X. The laptop even stops responding with the second method.The followings are my xorg.conf and log of XorgQuote:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
[code]...
I am trying openSUSE 11.3(KDE desktop) for the first time (also my first time with a linux OS). But i am trying to install the EgalaxTouch driver to get my touchscreen working. I have tried all the things from this topic: openSUSE 11.3 and eGalax TouchScreen but everytime i try to run the install.sh i get these errors no mather if i am directly logged in as root or using sudo in my command line:
I am busy from monday installing all kind of touchscreen drivers but they all won't install propperly (just like the original drivers they need the Xfree86-devel but i can't find it for openSUSE).
Ati 11.2 repo isn't accessable. Ati catalyst 9.3 dont want to install.
View 9 Replies View Relatedi'm using a Lexmark Pro 905 printer , it's a local printer with Ethernet connection to the pc.I installed the driver and this used to work on 11.2, now with openSUSE 11.3 it's not working. THe yast test page comes out but nothing is printed from open office.I opened port 661 UDP in the firewall but still no result comes from open office.I then added the printer in cups but i still have an error and no print : ( cups-1.4.4-2.3.i586 )
Lexmark_Network_Backend_1
Lexmark Pro800-Pro900 Series
Local Printer Lexmark Pro800-Pro900 Series, 1.0
[code]....
I'm trying to get my Highpoint 2680 working on OpenSuse 11.4 I need to make a driver for this because Highpoint doesn't have one for 11.4. I downloaded an open source driver from the website of Highpoint you can find it here. First of all I installed this with Yast: gcc, binutils, make, kernel-source, kernel-syms en linux-glibc-devel After this was done I unpacked the tar file with the open source driver in it and did this:
[Code]....
I have bought a new Dell Studio XPS Desktop with Broadcom BCM57788 network card. The installation of the tg3 driver from Dell was done according to Documentation
But still, the network card is not there. When I call ifconfig, there is only "lo" and no "eth". In Yast it says that the Netlink BCM57788 card cannot be configured because the firmware is missing. I also already did modprobe tg3 and rmmod tg3.
BTW, I have installed OpenSuse 11.2 x32 which is Linux 2.6.31.5.