I tried install Debian 5.04 on Alix 3d2 board (no VGA) but after boot i see only one line (Probbing EDD (edd=off to disable)... ok) and everythig stops. I'm doing this from this instrucion [URL] I'm looking working solution (Under Win or Linux) to install Stable Debian on Alix3d2 and 2d2 via network (PXE). I have microdrive drives for this boards
View 1 RepliesI'm having trouble setting up new Alix URL... system with a wireless card. I got the card from an old working Buffalo AirStation router. The card is a WLI-MPCI-G54 and is using Broadcom BCM4306 chip. I've installed Debian on the system.My goal is to make a wireless access point by using hostapd authentication service. I thought it might be a good idea to verify that the wlan-card is working properly first, but it can't seem to detect my local wlan.
View 1 Replies View RelatedI have a strange problem regarding networking on the Alix 2d13 running Ubuntu 10.04. The Alix has 3 physical network interfaces, lspci says:
Code:
00:09.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Kernel driver in use: via-rhine
Kernel modules: via-rhine
00:0a.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Kernel driver in use: via-rhine
Kernel modules: via-rhine
[Code]...
It seems, if more than one cable is connected, a random hardware port is chosen as eth0-eth2. If only one cable is connected the port that is connected is chosen as eth0-eth2. Any idea what's going wrong here?
Doing a fresh F12 install on a Dell Vostro 430. Machine needs to have 2 Network adapters for our setup.The install seems to go just fine but the on board network adapter doesn't appear to get detected/configured. If I look in /etc/sysconfig/network-scripts all I find is ifcfg-eth0 and ifcfg-lo. Looking carefully at ifcfg-eth0 I see it's the second card that I've put in the machine.As a test I removed the second network card and did another fresh install of F12. This time in /etc/sysconfig/network-scripts all I have is ifcfg-lo. When I go to system>Administration>Network Device Control I see no network devices displayed.
Is this an issue others have seen with F12 or is it possible my on board network adapter has an issue?BTW I did check the BIOS to be sure that Onboard Lan was enabled and it is.output from "lspci -k " with both cards installed on machine (I only listed Ethernet controllers)
I have recently built a HTPC with a GA-G41m Combo and it has worked well with Ubuntu 10.04, however last week some time the on board network stopped working. I have tried different routers and different cables, but the network light wont come on. What Can I doo?
View 5 Replies View RelatedI've just set up a PC with CentOS 5.3 runing on near identical hardware to an existing 5.2 machine. Motherboard is Asus M2A-VM which I discover by chance generally works very well with CentOS. Ethernet is on board Nvidia.The older machine just did run gigabit speed without any intervention at all, rather to my surprise. The newer machine insists on running at 100 Mbit which is annoying as it is connected to a NAS through a gigabit dumb switch.
The obvious difference between the two is that ethtool on the older machine says that supported ports are TP, and so the port is TP. Whereas the newer machine says that supported ports are TP or MII and insists on running MII. I cannot change this with ethtool -s eth0 port tp. Perhaps not too surprisingly, mii-tool says that the supported speeds range up to 100 Mbit.
I have installed slacware 13 on an intel server, but the IP add that i have assigned does not work. I used ifconfig to check the ip but it shows me 127.0.0.1. I have run netconfig with the ip address i need and restart the machine, but it goes back to 127.0.0.1
View 2 Replies View RelatedI have installed CentOS. I have two ethernet card (one onboard and one PCI). I am able to set ip for realtek ethernet card and my atheros(on board) is not shown in network ifconfig shows only one ethernet card (PCI) hen i gave the command lspci i got the following output
01:00.0 Ethernet controller: Atheros Communications AR8132 Fast Ethernet (rev c0)
03:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
I want to install slackware on an Alix alix6e1 computer [URL]. i might be looking after, especially since it does not have a vga port?
View 3 Replies View Relatedi am doing my academic project on Alix 3d3 system boards can u me the OS and also i am writing some program using C which i have to load it into the system boards, so which compiler is best suited?
View 4 Replies View RelatedI've been through 4 Soundblaster and ESS sound cards now with no luck on the MSI P7N Diamond m/b machine. By design, its supposed to use the x-fi xtreme PCI express x1 riser board, but that doesn't want to work with any linux I have found, even though it does recognize via lspci and is supposed to be supported by the newest ALSA versions, which I tried according to the wiki. The machine won't even boot with the ESS AudioPCI 9752 board in it. It has an ES1370 chip on it.
The older PCI Soundblaster CT4810 with CT5880 chip on it did recognize via lspci but only works for 1 boot cycle with debian 5.04 or knoppix 6.01. It does work well with knoppix 6.2.1, which is where I might land with this machine if I can't get sound working on debian. The PCI Soundblaster Live! does not recognize via lspci. It doesn't even show up after a full from scratch reinstall.
So, will a USB sound card "just work"?
http://cgi.ebay.com/USB-2-0-3D-Virtual- ... 563813f87a
Or if not, maybe a cheap no name PCI card from ebay? I would rather not use my only PCI slot which would block install of better video cards, but:[URL].. Those are about the only thing I can think of that I haven't tried.
I was trying to get a SMART board to work with my install of Lenny on my iBook G4. By work with, I just need it to display what's on the iBook's screen, I don't need any kind of interactivity. Since it is an iBook, it uses a PowerPC processor, instead of an Intel, and the SMART board driver only works on an x86 processor, I can't use the driver provided. Is there any way to get this to work? I imagine that I need to edit the X.org configuration file!
View 1 Replies View RelatedI already had windows on my box, trying to install suze linux 10.1, but while I boot from CD, my first option is Boot from Hard disk and second is Installation. But for selecting installation option I am not able to access keyboard.
View 5 Replies View RelatedI am trying to run Fedora on a Soekris 5501. To do this I have written F10 to an 8GB compact flash disk using Fedora Live USB Creator, with one 2GB partition for the OS and a 6GB partition for storage. I get the following error when attempting to boot:
--------------------------------------
WARNING: Cannot find root file system!
--------------------------------------
[code]....
Config: Squeeze, 2.6.32-5-amd64I just installed squeeze and the network is up and nm-manager deamon if working but the Gnome applet doesn't seem to work as usual. It indicates no network although the network is available as indicated by ifconfig and route below. When I switch WiFi on, the nm works flawlessly. When I click on the applet icon it says "Wired Network: device not supported" (or similar, msg in french is
eth0 Link encap:Ethernet HWaddr 00:1f:e2:12:ea:d8
inet adr:192.168.0.182 Bcast:192.168.0.255 Masque:255.255.255.0
adr inet6: fe80::21f:e2ff:fe12:ead8/64 Scope:Lien
[code]...
How to enable Desktop Effects with Intel on board Graphics Card on Fedora 10?
View 1 Replies View RelatedI have installed Ubuntu 9.04
uname -r
2.6.28-11-generic
Checked cable/network with 386Box running Ubuntu 8.04 all OK. Could not get Realtek 8168 on mother board to work on Gigabyte H55M-S2H motherboard. I tried to install r8168 driver but no luck ... so I bought another Linux compatible card which turned out to be a RTL8139c (eth1) and the driver I am using on this is card is 8139too.
[Code]....
My preference would be to get the motherboard ethernet working but perhaps the card may be easier to get working. Anyway after searching the net for ideas and trying different things I've just about given up. I have reinstalled Ubuntu today so eth0 is back to using the r8169 driver. I'm no expert so my attempts at following other recipies have so far failed. From what I have read the 8139too driver should have worked with the RTL8139C chip so I have run out of ideas. I must be doing something wrong.
I just installed the Debian testing release(with LXDE) from this week. Everything works great except the network card. I know the network card works because Windows and the Parted Magic Live cd recognize it. Also "lspci" seems to list the card, but when I fire "ifconfig -a" it is not listed there.
View 12 Replies View RelatedCurrently my new server pc (Mobo - ASRock H97M-ITX/AC) is not connecting to the network and it seems to be due to the network card alx drivers. I have downloaded the compat drivers and backports associated with the issue in other posts and on other forums but haven't been able to get it running.
When I install a usb drive of any type to try and transfer the drivers over I get the messages "443.057769 sd 7:0:0:0: [sdb] Assuming drive cache: write though" & "443.057769 sd 7:0:0:0: [sdb] No Caching mode page found".
I have been looking around these forums and google for the past week or so and have tried re-installing and alternative hardware etc. with no luck.
I installed debian 8.1.0 (netinist-i386) in my laptop at work using ethernet (installed mate desktop). At home I do not have such thing, so I should use my phone connection. I can not use wifi due to b43-firmware. I use usb tethering as my only solution. Now I connected to my phone but do jot have internet access in laptop. ping http://www.google.com or 8.8.8.8 or any other address says destination host unreachable,
ifconfig shows usb0 is ok
/etc/resolv.conf:
#generated by networkmanager
nameserver 192.168.42.129
I am trying how to do a network install of debian,by dumping the contents of the entire DVD on my http server,and booting off my other machine using the minimal cd and selecting the local mirror.The Error i get when i proceed to the 'download installer section' are
Code:
Menu item 'download installer selected'
anna wget: server returned error: HTTP/1.1 404 NOT FOUND
[code]....
I have installed i guess everything needed to add a VPN in my network manager, but its greyd out.
Installed on the machine I have installed
i A network-manager - network management framework (daemon and u
i network-manager-gnome - network management framework (GNOME fronte
i network-manager-openvpn - network management framework (OpenVPN plug
i network-manager-pptp - network management framework (PPTP plugin
i network-manager-vpnc - network management framework (VPNC plugin
I have checked the synaptic too and everything seems installed.
debian stable and gnome classic
I'm trying to install using windows 7 on a 2010 macbook pro. Firstly the network configuration won't work and secondly the cd rom can't be detected. I've rewritten the usb drive several times with no joy.
View 3 Replies View RelatedI'm trying to install Debian 5.03 from the netinstall on a usb flash disk. When it gets to the network initialization step, it fails and cannot get an IP from DHCP. Manual configuration does not work either. Out of desperation I installed windows to see if the network device was broken (this is a new motherboard), however it works fine without drivers even. Invoking lspci shows that it is a Realtek RTL8111/8168B PCI Express Gigabit Etherent Controller (revision ff)
View 4 Replies View RelatedI'm new to Debian,I download a Squeeze amd64 installation CD and ready to install it.
My laptop is Compaq Presario CQ40-115AU,AMD 780G board with ATI Radeon HD3200 graphic card integrated,wifi chip is Broadcom 4312 14e4:4315. Now I don't have network connection in home,I have to install the Squeeze,and get my wifi work to do the further update at any cybercafe with wifi hotspot. I found this website,provide all the package,but I don't know which to download to get my wifi work.
I'm trying to install Wheezy on a Thinkpad T23. want to use Fluxbox, so during installation I uncheck the graphics options because I can install X and fluxbox later. After the install, the first time it boots up it can connect to the wired network and it will download things. But, if I reboot then it somehow loses its ability to connect to any wired network (and the T23 doesn't have built in wireless, so it obviously can't connect to wifi). there something that I can do to get ethernet back? Or, is there a way to, while I'm still on the first reboot, permanently install the ethernet drivers?I'm finally trying tmove away from Windows because a friend happened to show me his laptop which was running the free and open alternative to OneNote (Xournal) that I've been needing.
View 2 Replies View RelatedCompletely new to Linux. I have two PC (both with Windows XP SP3) and an HP printer that are networked together with Ethernet cables and a 2Wire gateway. I now would like to install Debian GNU/Linux 5.0.6 on one of the computers and make it a dual-boot machine. The other PC will remain with Windows XP only. During the installation of Debian (5.0.6, 64-bit), I am asked to supply the domain name of the network.
It tells me that I can make up a name but to make sure to use the same domain name on all the computers. I have set up what Windows calls a Workgroup so that the two PCs can have access to each other's files. Would the name that I had assigned to the workgroup in Windows be what Debian is asking me about? The end result is that I want to be able to access Windows files and folders using Debian and vice-versa.
I am using mini.iso to install Jessie from network and I need lose setup command that is required by cryptsetup for mounting the detached header of an encrypted volume. Is there a way to get losetup from network during installation? For example by means of anna-install? Does any package from udeb.list contain losetup?
View 0 Replies View RelatedI've been in a difficult situation since we're having only wifi and there is no way to connect my laptop to the internet via a LAN cable.
Debian's packages don't support my wireless card. However this one works: [URL]
Is there any way to install this driver for the Installer to connect to the internet while installing?
I don't know what exactly to do when the Installer ask for my network driver so that I can use it.
I have a new Thinkpad T520 from work and am trying to put Debian 6 on it. I previously had a Thinkpad T42 and was able to install Debian 6. I recall having to find the driver and install it separately, so I downloaded all of the non-free drivers, but the network detection step doesn't seem to let me select my own driver.
I've been thru this at least 4 times, both the standard 6.01 and the AMD64 bit version, both behave the same. This has the (unfortunately) the Thinkpad b/g/n wireless card, but the wired ethernet is the Intel 82579LM gigabit. Seems there would be a driver with Debian 6 that would support that one.I can't stand running Windows 7.