so im trying to install iw so i can get my 3945 abg card to inject properly
im coming up with this error
HTML Code:
cody@WARMACHINE:~$ cd iw-0.9.1*
cody@WARMACHINE:~/iw-0.9.1$ make
CC mpath.o
[Code].....
I want to inject my card (Intel pro 3945 ABG) by using ipwraw-ng-2.3.4-04022008.tar.But I got a problem during the installation that driver.I want to use the driver in BackTrack4. But I can't connect to internet with BackTrack4, so I download it from Window 7 and copy to my thumb drive, and past to the desktop of BackTrack4.
Then I open terminal, decompress the tar file.
Another folder(ipwraw-ng) is appear on the desktop.
Then I change to the "ipwraw-ng" directory (cd /ipwraw-ng)
Then I compile with command (make) and the error start.
It shows error like below
[Code]...
i am using fedora 14 in my lenovo z560 laptop. It contains broadcom wifi card. The configuration is.Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g LP-PHY [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] I want to inject monitor mode in my laptop to run kismet . But i can't. I installed broadcom-wl driver in my laptop but i think its not compatible to run monitor mode..
when i run kismet it show me error that :------ try some other open source kernel driver And the other is :- kismet find only binary value eth1 port. It isn't detecting wlan0 port
i have an Acer aspire 4920 laptop with opensuse11.3 installed and wifi card has identified home wifi, but for some reason when i enter the wpa-psk key it doesnt connect.i have been at this problem for several days and scanning the net for answers, without joy.i dont know about the command or terminal line, i have tried to type in commands but i get no joy.
View 4 Replies View RelatedI had to send my laptop back for repairs, so I have an older Dell 1720 laptop that I threw the Hard Drive into, similar specs, just the wireless card is different. So what i need to do is somehow activate the driver for the Intel 3945 wireless card in this dell laptop.
View 2 Replies View RelatedWindows crashed yet again so I thought I'd switch to Ubuntu. Install of 9.10 went flawlessly, everything looked great and worked perfectly. Next day after restart the wireless wouldn't connect. I looked around for solutions and used a wired connection to install wicd and suddenly wireless worked again. But next day after restart wireless wouldn't connect again -
I keep getting a popup asking for my WPA key despite the fact that I know the key is entered correctly. I decided to install 10.04, thinking maybe that would help. It didn't look like wireless was working but after a restart it worked and it worked again after another restart! Fantastic! But today, I'm back to square one. Using Windows again.
TL;DR - Wireless won't connect to the network which it can definitely see - repeatedly presents "Enter WPA key" prompt despite key being correct and wireless working flawlessly under Windows.
1. Machine Brand and Model
Dell M65
2. Wireless Brand, Model and Wireless Chipset
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
[Code]...
Wireless worked fine on live cd, but for some reason not after install. I think maybe the driver is not loading, but I am a pretty much still a noob, so my opinion isn't worth much. If it is the driver not loading, I don't know what to do to fix it. Here is my wireless output information.
Code:
linux:/home/linux # lspci -nnk
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Toshiba America Info Systems Device [1179:ff10]
Kernel driver in use: agpgart-intel
[Code]....
I'm just starting out with ubuntu (10.04), and installed it using a live cd on my alienware m5500. I had the update manager update everything, and then went looking on how to properly use my nvidia graphics card (geforce go 7600) because the graphics weren't looking very good, and I couldn't use any desktop effects.
I followed the directions found here in order to blacklist nouveou and enable the current nvidia driver. However after rebooting, and every time I time I turn on the computer, it never makes it to the desktop, i usually end up seeing the ubuntu startup and/or the nvidia logo before it proceeds to one of several screens (none of which allow me to click or type, although sometimes i can move the mouse).
-black screen
-black screen with light gray bars top and bottom
-black screen with vertical green line
-orange and purple horizontal stripes
-purple and light purple horizontal stripes
Thinking that it could be one of the listed bugs from the directions, I followed the work around for "Screen Blanks/Monitor Turns Off", but the problem persists. I have used the live disc to do a fresh install and attempt it about 3 times.Anyone know what this could be, or have advice for troubleshooting? Let me know if I can provide any other information that may prove useful - I'm fairly new to linux in general, but I can probably get some information from recovery mode if I've got a little guidance.
I'm having a problem here with my graphics card. Until not very long ago I was using the controller Ubuntu downloaded for me. However I recently downloaded another one from the ATI page, called ati-driver-installer-11-3-x86.x86_64.run and installed it.
So far, I've encountered two new problems:
1. The ATI Catalyst Control Center would not open after I setup the Tear Free Desktop.
2. The computer is running slow. Files take longer to open, minimizing and maximizing windows takes longer. Wi-fi connection takes longer to connect, etcetera. Overall, everything is going slow.
Are these problems related? I would like to uninstall the driver as the computer was working just fine before. In addition to this, I have firefox 4.0 and the colors on most of the images are darker than they should. The images look fine on other browsers except firefox. I read I had to do type "about:config" in the address bar, find "gfx.color_management.mode" and change the value from 2 to 0. What did I exactly do there? I took the advice from this thread: [URL]
I want to inject a packet with specified TCP options: Maximum Segment Size, Window Scale Option, Timestamp Option... The man page mention very little about that:Quote:-o TCP-options-fileThis will cause nemesis-dns to use the specified TCP-options-file as the options when building the TCP header for the injected packet. TCP options can be up to 40 bytes in length. The TCP options file must be created manually based upon the desired options. TCP options can also be read from stdin by specifying '-o -' instead of a TCP-options-file.I don't understand what TCP options file structure is? ASCII, hex or raw? One way to try: in Wireshark, select the Follow TCP stream option of a packet, save as with some types: ASCII, hex... and use it for input:
Code:
sudo nemesis tcp -v -fS -D localhost -o /path/to/<TCP_options_file>
the output displays:
[code]....
I was curious if anyone has dual booted Ubuntu on this model iMac, (Mid 2011 with 4gb ram, 2.5GHz Intel Core i5 processor, the current model in the apple store).
When I dual booted on my MacBook I came across a plethora of problems, such as the sound not working properly or the wireless card not being supported.
Does anyone know if these same problems exist for the iMac or is everything business as usual?
I read through the sticky of wireless card not working, and I followed through with the steps, with the exception of looking for firmware, because I'm certain it has it, being that the card works when I'm running Windows, and overall the system recognizes the device.
The only difference is, I notice that the activity light on the card itself does not turn on when running openSUSE. It recognizes the card, it even detects the network, but when I enter the WEP key and finish, it does nothing afterwards. Still no internet.
Card: Linksys WMP54G v4.1
In Fedora 12, I am trying to use a program that uses uinput to inject mouse events to control X applications. This worked with Fedora 9, but doesn't with Fedora 12. I see the following in my Xorg.0.log:
(II) config/hal: Adding input device Prototype IRPointer Device
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 1.7.1, module version = 1.2.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
[Code]...
The device is not a synaptics touchpad, and so the X load of the driver is incorrect. But I don't know how to get X to ignore it's own driver and use evdev. (Or even if that's the right thing.) A general explanation of how hal and evdev are related, for the current X server,
Quote:
NOTICE: Some very old nVidia Video Cards from more than 9 years ago might not work with this way, but just try this method because you'll see if there's a driver available for your video card in Fedora or not.
I have been noticing that it was hard to set up my own NVidia video card, and alot of other people shared the same problem as I had. I have been experimenting with some things, and here's what I did to solve it.
It's fairly easy, anyone can do this. Read and follow these instructions:
Install all updates. Although it seems unimportant, it really is.
Go to [url] and follow the instructions to install the free and nonfree repositories
Go to System > Administration > Add/Remove Software
Search the following: nv
Click everything which has to do with NVidia. Do not check the checkboxes yet, but read the descriptions. If you've found your video card in the description, check the checkbox at the left of the title.
Install the drivers by clicking "Apply" at the bottom of your screen.
After installing, go to Applications > System Tools > nVidia Display Settings
Set the properties of your video card, such as TwinView or higher screen resolutions.
After you've set it up, click Apply to preview your settings. Change some settings if you like, and then click Apply when you're done. DO NOT EXIT YET!
Click "Save to X Confguration File, but do NOT save the file. Click "Show preview..." and copy the text in the preview.
Go to Applications > System Tools > Terminal and type "su". Press Enter and enter the root password.
Now type:
Code:
Select all of the text in the document and delete it. Then, paste the text of the "Save X Configuration" window into the text editor.
Exit out of the terminal.
Exit out of the nVidia Display Settings application. Do not save anything from this application.
Log out and log back in to see the changes.
If you want to change some settings, repeat steps 7 - 16.
A few days ago I setup a pc. It contains an "Intel ICH5" sound card. Before I begin posting all the configuration stuff I've tried so far what the standard procedures are to set it all up for recording the sound card output (with Audacity)?
On my older computer it all worked fine but now I only get silent recordings. However sometimes (when I played on the controls the right way...) I get recordings where you can (amoung some noise) recognize the stuff I actually wanted to record very low... Apart from Audacity I've also tried
Code:
arecord -vv -fdat audio.wav
which didn't work either. That's why I think the problem is not related to Audacity but to the system.
Is the combination of OpenSuse 11.2 + ALSA + Intel ICH5 commonly known to cause such trouble?
A wifi card with the ath5k driver used to work properly until a couple of weeks ago. Now, if I ping the router the response times sometimes are okay but often fluctuate into the range of many hundreds or thousands of milliseconds. Occasionally the connection breaks down entirely.My laptop, which uses a different card, works fine (typical ping response times of 2 ms), so its probably not the router which is faulty.I use opensuse 11.3 x86_64, currently with the 2.6.34.7-0.7 desktop kernel and knetworkmanager
View 1 Replies View RelatedI have a problem with a new GeForce 8600GT graphics card. I just installed the card into my Dell Optiplex 745. When I boot the PC I have no image until the Ubuntu logon box comes up. No bios info, no boot menu, no grub menu, nothing until the Ubuntu login. Once I get to the logon prompt everything seems fine except when I use CTRL+ALT+F1 to get to a console. Then I get nothing but a blank screen. When I press CTRL+ALT+F7 my desktop loads fine and all is OK again. I had a problem trying to get the nVidia drivers installed because I didn't have a usable console. I had to use SSH to install the drivers. I'm using this card with an HP 1755 flat panel that's about 5 years old and a Dell Optiplex 745 with Intel Dual-Core CPU.
View 8 Replies View RelatedA couple of weeks ago, I installed kubuntu 10.10 on my laptop and my wireless card has not worked ever since. It was fine under 10.04.lspci:
Code:
06:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
[code]....
Anyway, I've a decent understanding of the various Linux console commands and know how to work my way around a text editor or file system. But I can't seem to fix what's wrong with my computer. I'll list my info here and then discuss the most pressing issues that I need help with.
It's a 17" PowerBook G4, with Airport Extreme (which I understand is a headache all on its own: I'll likely get to that later)
Results of ~$ lspci:
I downloaded the most recent .iso for the PowerPC from [url], specifically the 4.4 GB DVD copy.
During installation, I told it to install only the Desktop Environment and Base System. Installation went through without a hitch, though it failed to connect properly to my Wireless card.
The first issue I encounter after booting is during the login. When logging in as a non-root user, I'm told to change my password immediately (root enforced). I've done this every time I've logged in. Immediately after when I log in I'm told that the system clock is wrong: It's currently set to Jan. 1, 1970. If I try to change it, I get a message saying that I can't, and my desktop won't load properly. If I ignore the system clock issue and try to change it in System > Administration > Time and Date later, after entering my admin password I get a message that says
Failed to run time-admin as user root.
Failed to communicate with gksu-helper.
Received:
Changing password for root.
While expecting:
Apparently the password issue is related to the Time and Date settings (according to Google), but I can't fix those because it wants me to change my password.
I recently installed the XFCE spin of Debian (amd64) on my Lenovo L440. I tried installing it before, but apparently the 3.2 kernel that ships with Wheezy doesn't properly support the proprietary firmware for the wireless card, blah blah. So I wound up using Windows 8.1 for a bit, and then Fedora (boo). Anyway, with the wheezy-backports kernel (3.16.7-ckt4-3~bpo70+1) everything works like a charm. Everything, that is, apart from the sound card — the entire system is completely mute. Well, apart from the system beeper. I searched the forum and found another thread, but that guy was (for some reason) just running dwm — I figured XFCE might feature a more complete sound system. But maybe the output he gave will be useful in my case as well:
Code: Select alleirik@gerhardsen:~$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDA Intel HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: HDMI [HDA Intel HDMI], device 7: HDMI 1 [HDMI 1]
[code]...
I also tried running alsactl init (as root), which doesn't appear to have made any difference.
i can't connect to my wireless network (wpa psk) with ubuntu 11.04 and my wifi card Intel 3945 ABG. i've done some search on the forums here and none of the workaround i've found works.
Code:
root@razor:~# cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=11.04
DISTRIB_CODENAME=natty
DISTRIB_DESCRIPTION="Ubuntu 11.04"
[code].....
have read [URL] lspci | grep Wireless 10:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02
[Code]...
have read [URL] but still could not issue the problem how should I resolve my wireless isusues?
fresh install of 10.1 on an older sony laptop wireless icon is on the toolbar, and my router is listed icon has a red exclamation mark my wireless button on the laptop is set to "on" dmesg | ndis reports "wlan0: link is not ready"
View 4 Replies View RelatedI have an Intel 3945ABG WiFi card in my Laptop (Dell Inspiron 6400). The problem is that I'm not able to get my card detect the Wireless Network. I'll list the prolem more specifially below. O.S. Fedora 12 x86-64
1. The Network Icon on the Taskbar (is it what it is called here in Linux??) shows Wireless is Disabled under the Wireless Networks. Wired Net works fine.
2. If I goto System->Pref->Network Connection the Network Tab is empty.
3.Under System->Admin->Network Config I can see two Devices; one is eth0 (active) with a checked check box. Second is wlan0 which is Inactive and has a checked Checkbox. The Activate and Deactivate buttons are disabled for both these. If I go and see in the Properties of the wlan0 it says controlled by Network Manager checked but the Network Manager comes up empty.
4. This forces me to remove that "controlled by network manager box" which enables the activate and deactivate buttons. Now I can Activate my wlan0 adapter and the light on the Laptop for WiFi starts up. During startup (activation I get this error in the pop-up box:
Error for wireless request "Set Mode" (8B06):SET failed on device wlan0 ; Invalid argument.). But the popup eventually closes auto. The Network Config box now shows it active but the Taskbar Icon still shows Wireless is disabled. And still the Network Connections has an empty box under Wireless tab. I donno what to do next. The card worked fine with Ubunto 9.04, openSuSE 11.2 (both 32 bit btw) and Fedora 11 again 32 bit.
working to sort out the damn wireless for too long. Mine in cent05 5.2 . network manager is on and I can see the icon on tray. It list all the wireless connections too, but just won't connect. WPA encry is disabled. further details below:
# lspci | grep Wireless 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
# ethtool -i eth1
driver: ipw3945
version: 1.2.1dm
firmware-version: 14.2 1:0 ()
bus-info: 0000:0c:00.0
[Code]...
I have installed xubuntu version 10. My sound card is a Yamaha dS-1S, and seems to be properly configured. Alsa mixer doesn't indicates any error. However, I can't manage to get any sound. I have checked that jacks are correctly plugged.
View 4 Replies View Relatedwhile sending mail form squirrer mail it gives erorqmail-inject: fatal:unalbe to exec qq(#4.3.0)iam not able to send mail.i googled but not got solution.
View 2 Replies View Relatedhow to make intel 3945 to work on RHEL5 ? Apparently that hardware is not officially supported by Red Hat so they do not provide drivers. what happens on my PC is after login I do not have the wireless card led is off and when I try to start the wireless connection I get
SIOCSIFFLAGS: No such file or directory
I'm not a real linux expert but I do use it since long time.
i have a little experience with ubuntu but i have had bugs that are not resolvable at this time in ubuntu. so instead of giving wild bill back my pc i am looking for a new distro. my concerns with ubuntu revolve around acpi. no fan control and high temp. the 2nd problem that is almost overlookable is the ata1 softreset error. it usually is no problem but occasionally have to do manual fsck to fix. so heres my laptop specs. toshiba a305d-s6848. amd turion x2 ati x1250 integrated. 3gb ram. 500gb hd vista and ubuntu 9.04 dual boot grub with 100gb ubuntu and the rest vista. so q1= what suse version would be best?
q2= is suse's acpi better? ubuntu runs all features but fan control
q3= is suse as easy to install? or harder
q4= ati graphics i know for my card went to legacy what version still has the ati drivers for my card
q5= is suse easier or harder to work with and get everything working.
i know no linux is or opsys is perfect. im just looking for one that is stable and works the pc correctly. i know its a big thing to ask. i know no one can tell me that. but just looking for suggestions. im thinking of downloading suse and does all the downloads support live sessions.
I have an EeePC 4g netbook which only has a 4Gb hard drive and I thought I would like to install Fedora 13 on an 8 Gb SDHC card and use it to boot the netbook.
As neither the netbook nor I have an optical drive, I made a bootable USB memory stick using Unetbootin which boots the netbook and could be used like a live CD to install Fedora.
On booting with the live USB stick, with the blank SD card in place, and clicking on the install icon, the installation starts but then there are 2 problems; the first is that the installer appears to want to install to both the SD card and also the USB stick. There is a tick in the box beside the USB stick which I can't remove.
I decided to ignore that and put a tick in the box beside the SD card but when it got to the point where it creates partitions it said "Could not find enough free space for automatic partitioning. Please use another partitioning method"
Surely 8 GB is more than enough space for partitioning, so where am I going wrong and why does it want to install on the USB stick as well?