Fedora :: Inject Monitor Mode In Broadcom 4313 Wifi Card?
Mar 28, 2011
i am using fedora 14 in my lenovo z560 laptop. It contains broadcom wifi card. The configuration is.Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g LP-PHY [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] I want to inject monitor mode in my laptop to run kismet . But i can't. I installed broadcom-wl driver in my laptop but i think its not compatible to run monitor mode..
when i run kismet it show me error that :------ try some other open source kernel driver And the other is :- kismet find only binary value eth1 port. It isn't detecting wlan0 port
View 10 Replies
ADVERTISEMENT
Dec 24, 2010
ok basically i have a new dell inspiron n5010 with a broadcom 4313 wifi card. it doesnt work with ubuntu studio 10.10. I have the drivers all installed and it works on ethernet with the broadcom STA proprietry driver. if i disable this driver the eth doesnt work. but the driver shows its working (screenshot-1).
There is no pop up or anything in the task bar for detected wifi. i open the network settings and it shows up with a wifi option but i have to go into properties and manually type in what i have "the_den_meribel". which didn't work. (screenshot-2).
i have tried the other driver broadcom-sta-common and that doesnt make it work either. screenshot-3. i did try to install the "lp-pphhy" or whatever it is (seacrh for firmware-b43 in synaptic).
i have a list of results from what i have typed into the terminal: dell inspiron n5010
Code:
sam@drytopubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18)
[Code]....
View 8 Replies
View Related
Jul 20, 2010
I am running Lucid Lynx, kernel 2.6.32.23 generic, I have a card with the Broadcom BCM4311, with the STA Linux Wireless driver. I have no idea how to get monitor mode to work with the Aircrack-ng suite's Airmon-ng command. I use the command: sudo airmon-ng start eth1
And I get this output: Found 5 processes that could cause trouble. If airodump-ng, aireplay-ng or airtun-ng stops working after a short period of time, you may want to kill (some of) them!
PID Name
883 NetworkManager
893 avahi-daemon
896 avahi-daemon
931 wpa_supplicant
[Code].....
View 4 Replies
View Related
May 28, 2011
my wireless is not working on my lenovo. The problem is when i got to network manager and try to select enable wireless once i select it, it unselect it self after a second. i tried everythink i fond on the net already and also tried with support in irc channel but still nothing.
uname -r 2.6.38.6-27.fc15.x86_64
ifconfig
Code:
[code]....
View 14 Replies
View Related
May 12, 2011
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]...
View 5 Replies
View Related
Nov 27, 2010
05:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g LP-PHY (rev 01)
Methods Tried
First Attempt
[URL]
Nothing happens when I try either of these commands:
# modprobe -r b44 b43 b43legacy ssb brcm80211
# modprobe wl
and This one fails:
# iwconfig
Then Tried:
[URL]
When I got to:
# modprobe -r brcm80211 ; modprobe brcm80211
(nothing happens just sits blank again)
and
# iwconfig (fails)
View 4 Replies
View Related
Jun 9, 2011
I just installed latest stable Debian (KDE) on my laptop, Dell Vostro 3400, which uses Broadcom 4313 (I think) wireless controller. I did install the proprietary driver package from Debian called breadcom-sta-common<version no>.deb. I remember it's the same driver I used for my previous Ubuntu installation. I also installed the KDE Network ManagerFront-End and the wireless tab on the manager is disabled (greyed out). I finally tried the steps from Debian Wiki Wireless section and at the end, when I run "modprobe wl", it says "FATAL: Module wl not found". Is there some more steps I need to do?
View 2 Replies
View Related
Jul 19, 2010
From my lspci output I get Broadcom 4313 and 0x14e4:0x4727It appears that Broadcom supports this card with their Linux STA driverBroadcom.com - 802.11 Linux STA driver guess on that page mine is 4313 2.4 Ghz 0x14e40x4727 Dell 1501even though my notebook is Toshiba.Then they say that the driver is included with Fedora and Ubuntu but nothing about OpenSuse. Then they go on about compiling the driver myself. I'm pretty sure the modules required for compiling drivers are not available on a fresh install and without Internet connection.Is there an easier way to get the driver? Could someone knowledgeable make some .rpm that I can download on another machine and put on a USB stick? Or do I have to wait until Suse developers get to it?
Or could someone make wl.ko file they are talking about on Broadcome Readme? It looks fairly easy to install the driver, if I knew exactly what to disable/blacklist and what security module to load.Another thing I got from dmesg, not sure if it's of any help, was that for this card pci entry that goes like 07:00.0 there's "support D1 D2", then "#PME supported from D0 D3hot D3cold" then the next line "#PME disabled". I've searched this forum but the only time 4313 was mentioned when someone made a mistake with the model number
View 9 Replies
View Related
Aug 16, 2010
I'm trying to install the drivers for my Wlan card, I've downloaded the drivers in the tar.gz-file from Broadcom and untar-ed it in my /home/<username>/hybrid_wl-folder and cd'ed to it and I try to run "make" but I get an error: KBUILD_NOPEDANTIC=1 make -C /lib/modules/'uname -r' /build M='pwd' make: *** /lib/modules*2.6.31.5-0.1-default/build: No such file or directory. Stop make: *** [all] Error 2
I'm getting really desperate, I need my Wlan on Wednesday. I'm following the README but this is what I get.
View 7 Replies
View Related
Oct 18, 2010
My HP Pavilion dm4 notebook has the Broadcom bcm4313 and worked with the proprietary Broadcom driver provided with Ubuntu 10.04 but did not work with the corresponding driver provided with Ubuntu 10.10. The solution that worked for me (for a while) was to install "broadcom-sta-common" and its dependencies using Synaptic. After enabling the proprietary driver (System > Administration > Additional Drivers) and rebooting, wireless worked. I even shared this on this post. chargersfan420 get his Broadcom card functional again.
What changed to break it? Well, wireless had worked for several days, so I felt that I had solved the wireless problem. Now it was time to find a solution to unlock my BIOS settings. I successfully used PCCMOSCleaner to clear the password. After that, no more wireless. (Note to dm4 users: Apparently HP puts a password on the BIOS settings and makes it available only if you boot into the factory-installed Windows 7 and retrieve it. Of course I never booted into Windows 7 before upgrading the machine to Linux, deleting both the Windows partition and HP's hidden recovery partition.)
I uninstalled all the Broadcom stuff and reinstalled it all. Now I appear to have wl working, and b43 and ssb blacklisted, but network manager is not seeing any wireless connections available.
My Hardware: HP Pavilion dm4-1063cl My OS: Ubuntu 10.10 32-bit (clean install)
lspci reports this:
Code:
$ lspci -vvnn | grep 14e4
03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g LP-PHY [14e4:4727] (rev 01)
dmesg reports this: (MAC address edited out with hash marks.)
[Code]......
View 6 Replies
View Related
Jul 13, 2010
I'm sure you've seen this question before -- I tried searching but I can't find a clear answer. All I need is to get my wifi up and running in Ubuntu 10.04. I'm currently double-booted with XP on a Dell Latitude E5400 laptop. I'm in Windows right now. I can't post my lpsci readout because I can't access the internet from Ubuntu -- no access to wired connection.
I worked on this problem for a long time last night and fixed it somehow by installing a driver program -- it had "cutter" in the name. Today, however, I try to log in and Ubuntu won't connect to an open wifi point. Boot #1 it recognized it but wouldn't connect. Boot #2 it wouldn't recognize it at all (said "wireless is disabled" even though it wasn't. Boot #3 it would recognize the wifi point but wouldn't connect.) I can mantain a constant connection to this wifi in Windows XP and also on my Android phone.
I just want someone to please tell me how to get my wifi working reliably. I'm excited to switch over to Ubuntu, all I need is for the wifi to work. My wifi card is a Broadcom 43xx (4312?). Something like that.
View 10 Replies
View Related
Feb 8, 2009
A friend of mine has a Dell XPS1530 lappy that has a broadcom bcm4328 wireless adapter. I tried installing kismet on it so I can scan for wireless network in range. I configured it with the source driver as bcm43xx in kismet.conf and complained that the driver didn't support monitor mode. It uses the proprietary 'wl' kernel module to operate but kismet can't use the 'wl' module and it says the same error. I tried unloding the wl and b44 modules and loding the b43 driver but then the adapter stoped working. I searched on the net a bit and found out that kisment doesn't work with the prorpietary drivers for that card.
View 14 Replies
View Related
Mar 9, 2011
I have an emachines D620 laptop running Ubuntu 10.10 with a Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01). I havent done anything with it and cant seem to get it to work. I know this because when I had visto on it the card worked, but know it says that its firmware is not enabled and ive tried installing the drivers using the Additional Drivers under Administration. I would like it to be working so I can use my laptop's internet.
View 5 Replies
View Related
Apr 5, 2011
I recently installed Suse 11.4 on my Dell Latitude 2110 netbook using the KDE live distribution, and, after that, the Broadcom wireless ceased to work. To enable the wireless connection, I have to press Fn + F6. If I do it now, the wireless led indicator turns on for a couple of seconds, then turns off again. Moreover, the option to enable the wireless connection in the network manager is greyed out
lspci output:
Code:
0c:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)
iwconfig output:
Code:
wlan0 IEEE 802.11abgn ESSID:off/any
Mode: Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit: 7 RTS thr: off Fragment thr:off
Encryption key: off
Power Management: off
dmesg output:
Code:
[8.330963] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.
[8.362403] brcm80211 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[8.362422] brcm80211 0000:0c:00.0: setting latency timer to 64
output of rpm -qa | grep broadcom:
Code:
broadcom-wl-kmp-desktop-5.100.82.38_k2.6.37.1_1.2-7.pm.8.1.x86_64
broadcom-wl-5.100.82.38-7.pm.8.1.x86_64
View 9 Replies
View Related
Jun 16, 2011
I just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies
View Related
Nov 29, 2010
Here are the specs for the computer in question:
Distro: Mint 10 Julia Gnome
Dell Inspiron 1100
2.40 ghz Intel Pentium 4
8 kilobytes primary memory cache
512 kilobytes secondary memory cache
20 GB HDD
1 Gig MB RAM (2 512mb sticks)
Linksys Wireless-G Notebook Adapter WPC54G V3
CDRW/DVD Optical Drive
From the title of this post, you can see that I am having some trouble getting the Linksys Wireless-G broadcom card working. I have been doing some research and have heard that getting a broadcom card to work in Linux can be a real pain.
I have verified that Mint 10 recognized PCMCIA so I am good there. I installed Wifi-Radar to see if maybe it would recognize it but it did not.
When I type iwconfig, it does not show any wireless signals available. When I originally set up the partitions for this laptop, I used PartedMagic and was able to quickly set up the network on that with vertually no problem what so ever.
View 6 Replies
View Related
Mar 27, 2011
I recently installed suse 11.4 x64 onto my hp tx2000 tablet. everything has been working great including the wifi card. It's a broadcom 4328 a/b/g/n/bluetooth card and it was using the broadcom-wl driver. Earlier today i plugged in an usb wifi adapter to test whether it worked on suse plug and play. Well after plugging in and using this wireless adapter, my internal wifi card is no longer visible to the system. I've tried lspci and its not displayed. I booted into a different suse install and it wont work there. My bios does not seem to have a disable feature and the killswitch is in the correct position. The bluetooth is working but the wifi is not. In lspci i used to see "hp integrated (wireless+bluetooth)" and "broadcom 4328..." but now only the former.
View 9 Replies
View Related
Dec 13, 2010
I installed Ubuntu 10.10 amd64 online today. I was using 10.04 32-bit before, and the network drivers were easy to find and install. Ubuntu did the job for me and they worked flawlessly. It was a relief I didn't need to search around.
Even though 10.10 (64bit) found the drivers for me, both ethernet and wireless, they do not seem to be working alright. I installed both, made a restart. I found that the WiFi light on my laptop stays on, even if the wireless network is turned off using either the key combination (Fn+F2), or manually turning it off.
Issues with the ethernet? I am right now using ethernet but it does not care to detect the connection. Empathy won't connect automatically as a result- says no network connection. But here I am, posting this. Evidently, there is a connection, right?
Issues with the wireless? The WiFi light stays on all the time, and it isn't able to get hang of the connection I have at home. It just won't show any wireless connections available. When I tried to connect by giving it the SSID and the encryption type and password, it didn't work. Just kept asking for the password again and again (I have checked with the router- the password is correct).
View 2 Replies
View Related
Nov 20, 2010
so im trying to install iw so i can get my 3945 abg card to inject properly
im coming up with this error
HTML Code:
cody@WARMACHINE:~$ cd iw-0.9.1*
cody@WARMACHINE:~/iw-0.9.1$ make
CC mpath.o
[Code].....
View 2 Replies
View Related
Apr 3, 2010
First of all, this tutorial will use NDISWRAPPER, not b43, not wl (Broadcom STA). So, hooray for new method (actually, the only method ). Now, I don't want anyone to get scared because of bad experiences with Ndiswrapper or whatever, it's actually quite easy. I did not come up with any of this info. I'm just putting this guide together from Kacper Szczesniak's info (who came up with this method), WifiDocsDriverbcm43xxFeisty_No-Fluff from the Ubuntu Wiki, and my experience. The Broadcom STA (wl) driver has references to monitor mode in it's code, but does not have that functionality in reality. The Broadcom Windows driver on the other hand does have this capability. So, for monitor mode to work, you will need a patched version of ndiswrapper.
1) Install the Linux kernel headers:
Code:
sudo apt-get install linux-headers-$(uname -r)
2) Install the tools required to compile Ndiswrapper:
Code:
sudo apt-get install checkinstall dh-make fakeroot gcc build-essential
3) Unload current Ndiswrapper module, if running:
Code:
sudo rmmod ndiswrapper
[code]....
View 9 Replies
View Related
Jan 6, 2010
I want to inject my card (Intel pro 3945 ABG) by using ipwraw-ng-2.3.4-04022008.tar.But I got a problem during the installation that driver.I want to use the driver in BackTrack4. But I can't connect to internet with BackTrack4, so I download it from Window 7 and copy to my thumb drive, and past to the desktop of BackTrack4.
Then I open terminal, decompress the tar file.
Another folder(ipwraw-ng) is appear on the desktop.
Then I change to the "ipwraw-ng" directory (cd /ipwraw-ng)
Then I compile with command (make) and the error start.
It shows error like below
[Code]...
View 1 Replies
View Related
May 15, 2011
I had aircrack-ng running on my old version and it worked well in the old version of linux but now when i run the programme and put my card in monitor mode it throws me the following message:
Found 5 processes that could cause trouble. If airodump-ng, aireplay-ng or airtun-ng stops working after a short period of time, you may want to kill (some of) them!
PID Name
677 avahi-daemon
678 avahi-daemon
701 NetworkManager
765 wpa_supplicant
2037 dhclient
Process with PID 2037 (dhclient) is running on interface wlan0
View 4 Replies
View Related
Mar 25, 2009
I like to test my network often. Until recently, I've been doing so on my old Ubuntu 6.06 laptop... the problem is It's too slow (1.06 GHz single Core ), and old, (designed for Win 2000) to really be effective any more. So, recently I bought a new laptop...one with a Dual core Processor, and twice the speed. Anyway, I'm running Fedora Core 10 X86_64 on it. My problem is as follows:
Although I do have MadWifi installed, for some reason, I still can't put my Atheros based Netgear WPN511 into monitor mode. (in the Network configuration window, it says "Atheros Communications Inc. Atheros AR5001X+" I'm not sure what it means but I'll put it in in case it helps) does MadWifi not work with Fedora? if not, is there a Fedora 10 (X86_64) alternative?
View 8 Replies
View Related
Aug 8, 2010
setup the correct mode for my laptop-video card-monitor
Video card - ATI mobility Radeon X1600
External Monitor - Belinea b.display 2 22"
Right now the external monitor is working, but sometimes it goes black for 2-3 seconds and then works again. This happens sometimes 5 times in a row, sometimes once, sometimes none. Other issue, when I install any new kernel it doesn't work. I get weird picture on monitor.
View 2 Replies
View Related
Dec 9, 2010
Running Ubuntu 10.10 on Hp Mini 1030nr My wireless card is a Broadcom BCM4312. I have the b43 driver installed. When I disable networking I can change to monitor mode but then it changes back to manage mode when I enable networking again. I tried using airmonNG but it;s not working.
View 1 Replies
View Related
Dec 4, 2010
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
View 6 Replies
View Related
Jan 18, 2010
just installed it with a duel boot with windows, installed it using a live boot cd that i burned. seems like everything is good except i have no wifi i tried to do an update and possibly get the fix and i get an error when trying to install the updates..looks like i have more issues than i thought.. did i mess up by installing from the live cd?
View 14 Replies
View Related
May 31, 2011
I have an HP 5101 mini notebook. It used to run quite happily under Fedora 14 after running yum kmod-wl-PAE .
Fedora 15 seems to not have any simplistic solutions. I am confused by rebuidling the kernel and would like a simpler solution if possible.
Here is the lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
[Code].....
View 4 Replies
View Related
Jun 15, 2011
i am using broadcom wireless (4312) on my laptop with FC15 and configured it using [URL]. initially it ran great without any problem (for a week). but from yesterday, every 15 minutes or so, my wifi started getting disconnected, showing the wireless login screen . I can reconnect only by rebooting or restarting network manager service.
View 6 Replies
View Related
Jun 20, 2011
I have having trouble getting my broadcom wifi card working, it is a BCM43225 802.11b/g/n. I did mange to get it to work but after reseting Fedora 15 would not boot. How to get the WiFi card working that would be awesome.
View 2 Replies
View Related
