Ubuntu :: ATI Graphics Card Controller Not Working Properly
Mar 31, 2011
I'm having a problem here with my graphics card. Until not very long ago I was using the controller Ubuntu downloaded for me. However I recently downloaded another one from the ATI page, called ati-driver-installer-11-3-x86.x86_64.run and installed it.
So far, I've encountered two new problems:
1. The ATI Catalyst Control Center would not open after I setup the Tear Free Desktop.
2. The computer is running slow. Files take longer to open, minimizing and maximizing windows takes longer. Wi-fi connection takes longer to connect, etcetera. Overall, everything is going slow.
Are these problems related? I would like to uninstall the driver as the computer was working just fine before. In addition to this, I have firefox 4.0 and the colors on most of the images are darker than they should. The images look fine on other browsers except firefox. I read I had to do type "about:config" in the address bar, find "gfx.color_management.mode" and change the value from 2 to 0. What did I exactly do there? I took the advice from this thread: [URL]
View 2 Replies
ADVERTISEMENT
Jan 28, 2010
I have a problem with a new GeForce 8600GT graphics card. I just installed the card into my Dell Optiplex 745. When I boot the PC I have no image until the Ubuntu logon box comes up. No bios info, no boot menu, no grub menu, nothing until the Ubuntu login. Once I get to the logon prompt everything seems fine except when I use CTRL+ALT+F1 to get to a console. Then I get nothing but a blank screen. When I press CTRL+ALT+F7 my desktop loads fine and all is OK again. I had a problem trying to get the nVidia drivers installed because I didn't have a usable console. I had to use SSH to install the drivers. I'm using this card with an HP 1755 flat panel that's about 5 years old and a Dell Optiplex 745 with Intel Dual-Core CPU.
View 8 Replies
View Related
Jun 21, 2010
I'm just starting out with ubuntu (10.04), and installed it using a live cd on my alienware m5500. I had the update manager update everything, and then went looking on how to properly use my nvidia graphics card (geforce go 7600) because the graphics weren't looking very good, and I couldn't use any desktop effects.
I followed the directions found here in order to blacklist nouveou and enable the current nvidia driver. However after rebooting, and every time I time I turn on the computer, it never makes it to the desktop, i usually end up seeing the ubuntu startup and/or the nvidia logo before it proceeds to one of several screens (none of which allow me to click or type, although sometimes i can move the mouse).
-black screen
-black screen with light gray bars top and bottom
-black screen with vertical green line
-orange and purple horizontal stripes
-purple and light purple horizontal stripes
Thinking that it could be one of the listed bugs from the directions, I followed the work around for "Screen Blanks/Monitor Turns Off", but the problem persists. I have used the live disc to do a fresh install and attempt it about 3 times.Anyone know what this could be, or have advice for troubleshooting? Let me know if I can provide any other information that may prove useful - I'm fairly new to linux in general, but I can probably get some information from recovery mode if I've got a little guidance.
View 9 Replies
View Related
Dec 12, 2008
I'm using RedHat 9. I've already installed java and azureus/vuze too but when i run azureus there is a problem.
View 1 Replies
View Related
Jun 3, 2011
After upgrading (from 10.10), i get a line command prompting for login. I cannot get past this line/prompt. How do I bypass this prompt? So that I can access a prior version, if possible.
View 5 Replies
View Related
Jan 30, 2010
I read through the sticky of wireless card not working, and I followed through with the steps, with the exception of looking for firmware, because I'm certain it has it, being that the card works when I'm running Windows, and overall the system recognizes the device.
The only difference is, I notice that the activity light on the card itself does not turn on when running openSUSE. It recognizes the card, it even detects the network, but when I enter the WEP key and finish, it does nothing afterwards. Still no internet.
Card: Linksys WMP54G v4.1
View 5 Replies
View Related
Aug 24, 2010
I activated my graphics card on Linux Mint which is Nvidia GEFORCE GT 130M. Now when I boot up, after bios the loading screen looks like in the picture (sorry its crappy quality). When it gets to the login screen and afterwards it is just blank, but i can tell its running underneath because i can shut down by doing ctrl alt backspace and then tab and enter. I tried entering recovery mode but it was the same. Atm im using a live cd.
View 2 Replies
View Related
Oct 21, 2010
Just spent about 4 hours upgrading from 9.10 to 10.04 thinking it would fix my graphics problems. Basically I have no 3d acceleration of any kind, is there any way i can load the intel drivers? Because what I'm using now is really crappy.
[code]...
Can i just change something in my xorg to intel and it will load that driver ? I've tried the "hardware drivers" thing but it does not show anything.
View 1 Replies
View Related
Jun 11, 2011
I was curious if anyone has dual booted Ubuntu on this model iMac, (Mid 2011 with 4gb ram, 2.5GHz Intel Core i5 processor, the current model in the apple store).
When I dual booted on my MacBook I came across a plethora of problems, such as the sound not working properly or the wireless card not being supported.
Does anyone know if these same problems exist for the iMac or is everything business as usual?
View 1 Replies
View Related
Jul 30, 2010
I have a z9 volari Graphics card that opensuse 1.2 is recognising but the xgi driver is not present. I get the following when I startx:
auth: creating new authority file /root/.serverauth.4650
X.Org X Server 1.6.5
Release Date: 2009-10-11
X Protocol Version 11, Revision 0
Build Operating System: openSUSE SUSE LINUX
[Code]....
Perhaps my last post about this was too long and hence why nobody responded. So i will try and keep it simple and let the experts advise me.
I have tried installing an rpm that I got from rpm search. Namely xorg-x11-driver-video-xgi-1.5.0-6.1.i586 which seemed to install but when I did a query it said it was not installed, but when I tried to do an install again it said it was already installed ??
There is also a file called xserver-xorg-video-sis_0.9.3.orig.tar.gz which i got from this site. I have not managed to extract it properly yet but will look into that myself. It appears to have in it a makefile, so I presume it is source files and I could really do with some help in that.
View 2 Replies
View Related
Jan 12, 2011
A wifi card with the ath5k driver used to work properly until a couple of weeks ago. Now, if I ping the router the response times sometimes are okay but often fluctuate into the range of many hundreds or thousands of milliseconds. Occasionally the connection breaks down entirely.My laptop, which uses a different card, works fine (typical ping response times of 2 ms), so its probably not the router which is faulty.I use opensuse 11.3 x86_64, currently with the 2.6.34.7-0.7 desktop kernel and knetworkmanager
View 1 Replies
View Related
Oct 12, 2010
Just fitted an Inno3D (I-7300LE-G4E3) graphics card and I get a distorted boot up screen, a virtually unreadble boot menu (lots of extra white bits all over the screen) and when the system is booting the black screen with "booting from .." and the underscore at the end, is covered with white commas (?!), then the login screen pops up for a fraction of a second, then get a blank screen and no signal-cant get anything after this (or from the vga port on the pc)-I ve tried logging in even though I cant see anything, but no music , nothing.
Thought I might have to download drievers AFTER I d installed it, but as I had this problem, I removed it and tried to download driers before installation. Not sure which of the 4 to try, but tried 2 and neither works-GDebi is offered as an app to open them but nothing happens, nothing happens if I just click on them and when I try and install them from a terminal with the script from the nVidia site, it says unable to open them.
View 3 Replies
View Related
Mar 16, 2011
I am unable to get the hdmi audio for from my graphics card to work. I do not have any speakers to test the other two, and redundant, sound cards .My graphics card is the Nvidia gtx 285, I auto installed the drivers via ubuntu. It does not show up in the hardware tab of "sound preferences". It's not muted, I can't find anything relating to sound in nvidia-settings.but here is my aplay -l:Quote:
card 0: XFi [Creative X-Fi], device 0: ctxfi [Front/WaveIn]
Subdevices: 8/8
Subdevice #0: subdevice #0
[code]...
View 1 Replies
View Related
Nov 18, 2009
After a fresh install of F12 on pc with Riva TNT2 Model 64 graphics card, Login hangs once booted.
Worked fine on f11.
View 13 Replies
View Related
May 2, 2010
I have a Gigabyte GA-MA74GM-S2 motherboard with integrated graphics that shows up on lspci as an ATI Radeon 2100. I also bought a PCI-Express Nvidia graphics card so I could use the VDPAU feature on Linux (plays H.264 in hardware). The BIOS has three settings about which display to initialize first:
Integrated graphics
PCI graphics
PCI-Express graphics (PEG)
I set the BIOS on PEG, but
I cannot get anything, not even a splash screen or POST messages, to emerge from the PCI-Express graphics card. (I'm using a DVI connector; the card also has an HDMI output.)I cannot get the kernel lspci to see the graphics card; the only VGA controller it acknowledges is the integrated one.Running dmidecode acknowledges the existence of an x16 PCI Express slot, and it says
Current usage: Unknown
There is an additional BIOS setting called "Internal Graphics Mode" which is normally set to "Auto" which means it is supposed to prefer a PCI Express VGA card. I set it to "Disabled" which now means I'm getting no output at all. I will soon be learning how to do a BIOS reset!
Other information: The PCI-E card is a MSI N210-MD512H GeForce 210. This is a fanless card. Although there are no fans to see turning, the heat sink on the PCI-E card is definitely getting hot, so the card is getting some sort of power.It gets all its power from the PCI-E slot; there is no external power connector.The BIOS is an AMI Award BIOS.how can I make the PCI Express graphics card visible to Ubuntu?
View 1 Replies
View Related
Jan 27, 2011
I have been trying to enable compiz on my fedora 14, but when i enable the desktop effects the graphics just crashes and fedora freezes. When i type lspci -nnk | grep VGA for the graphics card i get:
I made alot of research on how to get Intel graphics work on Fedora, but couldnt find any solution
Same problem I had with Fedora Core 12 and 13.
View 5 Replies
View Related
Feb 4, 2011
I am running Ubuntu 10.10 on my old Acer Travelmate 661 LCi. Device manager tells me: info.linux.driver i915. Is there a better driver, and if yes, where can I get it and how can I install it.
View 1 Replies
View Related
Jan 14, 2010
I have installed the latest debian on a dell optiplex gx260 which has a 82845G chipset and there are some strange problems.The system is configured with autologon as a standard user. Sometimes, after logging on, the screen goes black but if I connect to it with vnc, I get a working desktop. Yesterday I booted it without a display attached to it and now I cannot set it to the right screen resolution anymore (1440 x 900) which was working fine before.
I have googled and searh the forum but cannot find the right information. According to Intel, the latest driver should be in the distro but I cannot find any details about that (version/date). grep Driver /etc/X11/xorg.conf returns
[Code]....
View 15 Replies
View Related
Nov 5, 2010
I have recently upgraded to Ubuntu 10.10. However the bottom of the screen is cut off with only a trace of it visible. I had similar problems with version 10.04 where both and top and bottom of the screen were not displayed.
I have noticed that version 10.10 does not use the proprietry driver the previous versions used.
In desparation I have tried Kubuntu but the results are still much the same.
Does anyone have any idea how I can display a full screen with an Nvidia integrated graphics controller.
View 9 Replies
View Related
Jul 9, 2011
I really wanna use the OS. I wiped my laptop and installed it but I can't change my screen resolution (it's stuck at 1024 X 768 and my refresh rate is at 0 HZ) I tried installing a driver that was for both the i9xx and i8xx chipset family but it doesn't look like it helped anything. I want to be able to play World of Warcraft Wrath of The Lich King but when I try it the way the computer is now the the frame rate is really really slow. I also need to fix my audio because there's crackling that comes from the speakers often. I attached a screen shot of what I get when I enter the command: sudo lshw -c video Changing the resolution isn't the problem so much as the fact that I can't change the refresh rate from "0 HZ" to anything higher so that my game will play smoothly. I would also like to put compiz fushion on my laptop as well but I don't believe it will work unless I resolve this problem.
View 9 Replies
View Related
May 26, 2010
I've got a "little" problem with fedora 13: dual head with nouveau is not working. gnome-display-properties recognizes two displays and i can configure it (left, right, mirroring, ...) but first display is always in standby. Seems it doesn't get a signal from graphics controller. Desktop seems to work fine (can move the mouse pointer on the other screen into "the black hole"). I use Fedora 13 x86_64.
[Code]....
View 3 Replies
View Related
Sep 15, 2010
I am testing Suse 11.3 and have run into a problem with Intel's integrated graphics and resolution. Here is a dump of the hardware information I pulled from yast.
[Code]....
View 1 Replies
View Related
Jul 18, 2011
[code]...
Just got World of Warcraft Installed and when I start the game after I get past the 2 cinema's while I'm trying to click yes on the rules the screen seems to bee flashing over and over and over. I was thinking maybe the 3d accelerator isn't installed or maybe I need to install something because its Intel?
[code]...
View 2 Replies
View Related
Sep 5, 2011
I just bought a new graphics card and installed it. it works perfectly although my sound worked perfectly this morning and I think the graphics card is overriding my built in sound card. I need help fixing the sound. The graphics card I bought is an ATI Radeon Cedar HD 5450 The sound I want to use is HDA VIA VT82xx
when I run alsamixer I get Card:
HD-Audio Generic
Chip: ATI R6xx HDMI
[Code]....
View 3 Replies
View Related
Mar 30, 2009
very much like everybody i am also waiting for centos 5.3, because 5.2 could not sit on my notebook due to obvious driver issues. would anybody tell if centos 5.3 support my x3100 graphics card and bcm 4311 wlan card?
View 5 Replies
View Related
Feb 13, 2010
i using wine windows windows compatibility layer(beta release) , i tried ride(micro controller and micro prosser simulator)open with wine , but it not work properly..
View 2 Replies
View Related
Jun 13, 2010
I have an HP presario CQ61 with a built in graphics card that never needed a driver to work (Intel Mobile 4 series chipset integrated graphics controller), but a lot of the images on the websites i visit appear like this... this is google for example.. [URL]
View 2 Replies
View Related
Jan 11, 2010
9.10 Problem with Graphics/3D and other I have a Thinkpad T42, 1.7GHz, 1Gb Ram and a Radeon 7500 Graphics card. Everything that I am having trouble with works just fine in Ubuntu 9.04(except for the sound). There are two problems that I think are linked or really the same. First off, When I turn off Compiz(Compiz works by default) then gnome-system-monitor does not work properly. At least the graphics side of it; the window appears black with random lines running threw it. The same thing will happen to Gnome-do if Compiz is off.
The second problem is getting 3d support to work. I installed and tried to run blender and I got this from the terminal:
[Code]...
Then it ether does not open or the computer locks up completely and I have to force a shutdown. Which ever one it does I do not get my desired results. When trying to do chess in 3D it tells that I have 'No Python OpenGL support'. So I install the python-opengl package from the repositories; the program now just errors on start and I had to uninstall python-opengl to get Chess to work again. I have tried all this with Compiz on and off with the same results. Anyways thats about it, unless somebody knows how to setup the sound so a program won't lock it from other, then thats all I am having trouble with.
[Code]....
View 3 Replies
View Related
Feb 13, 2010
I recently installed Ubuntu 9.10 on an old family laptop. It is a Compaq Presario V2000. Everything works perfectly except no wireless networks are recognized, even though I know there are available networks. My network controller is detected but is not doing it's job, which is finding available wireless networks! Using "system testing" I found this out about my network controller:
"Detecting your network controller(s):
Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)"
url
View 3 Replies
View Related
Jul 7, 2010
I have an issue with my Sound on OS 11.2.It is correctly recognized under hardware and the driver seems to start properly as well when I do rcalsasound start.But under Control Center / Sound Preference there is no audio hardware listed (and hene no sound playing)
View 3 Replies
View Related
