The time the server smbd and nmbd functioned normally but when I restart the service he returned smbd nmbd not normal but when I try to start it the following error occurs:
Code:
service nmbd start
start: Job failed to start
service nmbd status
nmbd stop/waiting
[Code]....
After running Bastille to harden my server, Samba stopped working. It had asked me if I would like to disable Samba during the configuration and I selected 'no' so it should not have done this.
When I tried:
Code:
sudo /etc/init.d/samba restart
Nothing happened. I found in the script, if it does not detect smbd and nmbd running, it just exits -- no error message, just simply does nothing.
I found that /usr/sbin/smbd and /usr/sbin/nmbd both had all permissions removed. I set them back to 755 and restarted samba normally.
I It does not start when the system boots. The smbd daemon is present and there are no suspicious messages in the system log, dmesg or the samba logs. The nmb service *is* enabled at all of the relevant run levels and does start if I issue the command "service nmb start" as root after I log in. This particular box's networking is 802.11n via a usb port and is under the control of the network manager. I have another fedora 12 box with an internal intel 5100 802.11n card and it does not have this problem.
View 10 Replies View RelatedI have an Ubuntu 9.10 server and I recently noticed that when it starts up I see the following displayed
* Starting init crypto disks..
* Could not access PID file for nmbd
I don't know where the message "Could not access PID file for nmbd" it doesn't appear to be coming from samba because samba is starting later in the startup. I've had no issues with samba and I can restart samba with no issues. Is this something to be concerned about? I noticed it started after I upgraded my samba server.
I am having this problem, that says in the boot up ~Could not access PID file for nmbd~/ I have been told to delete splash file. But i don`t know how to do so.
View 3 Replies View RelatedI cannot, for the life of me, get nmbd to run at boot on Ubuntu Server 10.10. On all other variations I've run, it's just automatically running. How does one go about this?
View 2 Replies View RelatedI have a new install of Ubuntu 10.04.1 LTS server. But I get errormessages trying to start samba.
caesar@klem:/etc/samba$ restart smbd
restart: Unable to connect to system bus: Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory
I have tride to remove an install samba. And deleted smb.conf. And startet with the original.
smb.conf:
workgroup = Easyways
server string = %h server (Samba, Ubuntu)
log file = /var/log/samba/log.%m
max log size = 1000
[Code]....
Here's the background info -- I recently installed Ubuntu server 8.04 on TWO machines that are exactly identical.On one machine, all seems perfect.On the other, when I execute "/etc/init.d/samba status" it always shows that smbd is NOT running.But it would seem that it IS running, since I can access the shares I've set up without difficulty either from smbclient on the server or from the windows boxes on the network.ps ax lists smbd as a process as well.The log tells me nothing -- it just reports that samba started. No errors. Not much of anything in there. And if I execute smbstatus, that works just like you'd expect.since the two machines are identical (and I mean exactly the same), and only one is doing this.
I guess I should be happy since they both work (seemingly perfectly).But it still bothers me that I'm getting the message that smbd isn't running on one of them. I tried uninstalling samba and reinstalling it on the machine giving me the erroneous (?) status message. But that changed nothing.Right now there's no data on the machine, and it's not in production, so just doing a bare metal reinstall of the OS is an option. But I'd like to understand what's happening.
Just like the title states, as soon as my server comes up, I see the samba share that I made and can browse it just fine.
I don't see the printer share nor can I print to the shared printer until I execute service smbd restart from an ssh login. Then I see the printer and then I can network print.
Before restarting smbd, I do check to see if it's already running and it is (two instances are running in fact). When I restart smbd, there are still two smbd services running but they have higher PID numbers (and I can then print).
I'm running 10.04. how to make it all start up happily the first time without any intervention from me?
I'm trying to get mySQL Daemon to start when the machine starts up (and it requires root privileges to run). The command to startup would be
Code:
sudo /etc/init.d/mysql start however that would prompt for a password, and that would not be very well possible now would it? Now, if i try to start it up without being root, it will not start. So this is my problem, maybe someone out there would know a bit more about this than me.
I've installed tucan on my HP Pavilion dv2800t with ubuntu 10.10.Megaupload download didn't starts or start later. If I try cut and paste link on Firefox I recives a message from Megaupload sites for more request by my ip adress and wait for download more minutes.The other downloads from rapidshare, hotfile ecc with tucan works fine.
View 1 Replies View RelatedI want to start a program which starts from terminal window and needs sudo permission. How can I start it from Application menu without need of any permission?
View 2 Replies View RelatedHow can I make slackware startx whenever it starts instead of having to go login as root and type startx each time?
View 6 Replies View RelatedHow do I log all start-up text from when Grub starts to when my desktop appears?
View 2 Replies View RelatedI use NetworkManager to handle my net connections and it's applet that allows me to control everything from the gui is called nm-applet. I was able to edit /etc/X11/xinit/xinitrc.fluxbox so that nm-applet starts when fluxbox does and away I go. From runlevel 3 that is.
On my laptop I like to boot into runlevel 4 for various reasons. When I start a fluxbox session from runlevel 4 this doesn't happen. What file do I have to edit to get this to start from runlevel 4?
installed corectly the program, but when I start it, it starts to integrate to the kernel, I got error and this is the log.
Code:
May 12 16:04:07.612: app-139838623995648| Log for VMware Workstation pid=25181 version=7.0.0 build=build-203739 option=Release
[code]....
dear, in centos / fedora, I can config to start a permanent vnc session by setting the /etc/sysconfig/vncserver file when the system starts. Is there any similar configuration in opensuse which give me a permanent session?
View 6 Replies View RelatedThis is on Fedora 11. How do I start up a shell script when the system starts?
View 6 Replies View RelatedI want to start recording when someone starts talking, and stop recording when it becomes silent. I guess if there is stream audio processing tool like ImageMagick, so I can strip away blank sections like this:
$ rec -t wav - | wavefilter -strip-blank=3sec | lame - >record1.mp3
EDIT This question is resolved by using:
$ rec -t wav - silence 1 0.1 3% -1 1.0 3% | lame - >record1.mp3
I've gotten everything working on my laptop except the webcam. I'm trying to use webkam (from kde repo) but the launcher starts up but the program doesn't start. The driver is "uvcvideo" which loads with no error messages.
Code:
62: USB 00.0: 0000 Unclassified device
[Created at usb.122]
UDI:
/org/freedesktop/Hal/devices/usb_device_c45_6406_noserial_if0_logicaldev_input
Unique ID: MtLc.1biges91ot8
Parent ID: k4bc.cO89g+iefn1
[Code]...
Iam tring to install 11.4 on my new computer, when i start the computer the green screen pops up and syslinux starts. However when it finishes loading a dialog box pops up saying "Make sure that cd number 1 is in your drive" . Obviously it it is,
because i am booting from the dvd. I dropped to the shell where i saw this message "Inappropriate ioct1 for device". What does all this mean.
Is there a quick and easy way to make sure apache always starts with a certain nice value?
View 1 Replies View RelatedI have a small network of an Ubuntu server 10.4 , Debian server, Win XP, and an ubuntu desktop 10.4. I have configured a DNS server and DHCP server successfully on my ubuntu server, also a slave DNS server on Debian. I recently configured apache2 as part of LAMP on ubuntu server, but when I type my ServerName in the URL of my Win XP browser, I get this response: The webpage "mansour.net" cannot be found DNS error occurred. Server cannot be found. The link may be broken.
I have an A Record in my DNS zone file for mansour.net and have that as my ServerName in apache2 Definition file, but I don't know why it is not working. I am trying to learn to install and configure various servers on ubuntu.
I want to run a web server.
I've done
When i do [url] i get a blank page.
I have posted this somewhere here before and solved it but can't seem to find it. Just waisted 50 minutes googling and checking man pages for upstart. By the way; are man pages written by someone using their tows to type and getting beaten by a stick for every character they type? It seems missing a lot of info. Anyway, I know smbd is started with /etc/init/smbd.conf and there is a line like:
Code: start on local-filesystems Now it needs to be started on? (manually) I can't seem to find any useful information but did seem to find the upstart man pages a hundred times or so (same info same missing parts). I would love to get involved writing documentation for these things if only I know what I was doing.
I am running a recently built Debian 'Lenny' system 5.0.4.I used the gui install and asked for desktop/file server/ I created a raid 1 systemsing two similar drives.Finally I set up some samba shares to use from my (wife's) windows PC. I wanted to use PC names rather than IP adresses to access the shares so activated wins.My Debian system, called arcturus, did not appear in windows network places. After much trial and error and googling found that the nmbd service had stopped.'/etc/init.d/samba restart' reported nmbd not present, stopped smbd and then restarted both. My networking then all came to life.There is a Ubuntu forum discussion around this subject and the consensus seems that the samba daemons are starting before the network is properly established. I have installed a work-around by putting the restart line in /etc/rc.local.But I'm concerned that I have some kind of configuration error.The following is a section of my log.nmbd after setting logging to level 3:-
Initialising global parameters
[2010/03/07 14:22:56, 3] param/params.c:pm_process(569)
params.c:pm_process() - Processing configuration file "/etc/samba/smb.conf"
[code]....
I'm running a fedora 14 file server with samba for a windows network. When I reboot my file server my samba share is no longer available. After a long search I found that if i run nmbd as root, the share is accessible again. I guess I can run nmbd everytime I reboot but I think something is wrong with my setup and it's one of those things that if I just ignore it will come back and bite me from behind
View 6 Replies View Relatedsamba quit working after win7 I'm new-ish to linux(not using ubuntu tho, but servers)i don't know what PID is.. i just installed a new ubuntu server of an old computer, for file sharing in workgroup with samba, and a little apache server running webmin is also running, giving me an error when restarting samba all worked very well untill i used win7 to access the \server this blog post have a fix for vista7? connecting to samba, but wont fix my problem after i connected to the share with win7 nothing seems to work
Quote:
# service samba status
* nmbd is running
* could not access PID file for smbd
and this:
# service samba start
* starting samba deamons [fail]
restart wont work, neither do reboot the server. I am clueless some of my research is pointing me to /var/run/ and there is no smbd.pid there, not in any folder (nmbd.pid exist) i found something
# service samba reload
* Reloading /etc/samba/smb.conf smbd only
No process in pidfile `/var/run/samba/smbd.pid' found running; none killed.
[ OK ]
i dont have any smbd.pid in the samba dir, should i create a new one.. and where do i get the PID -id that should be inside?
I'm having a problem with Samba. In log.smbd Im getting this message periodically:
View 8 Replies View RelatedI have just installed Debian 6.0.1 base install, for the use of a file server. I installed samba using apt-get and am using: smbd version 3.5.6
Here is my smb.conf file. Very basic, which by the way, seems OK according to the output of testparm.
Code:
[global]
log level = 3
workgroup = INERT
wins support = yes
[test]
[Code]....
I don't understand why smbd is not reportedly binding to IPv4 ports.