Does anybody know what to do? Internet works fine except for that problem.
I can attach files of 33kb in web-based email service (Gmail) but no big ones.
I'm using ZyXEL 660HW T2 router for my internet connection. The router is already set up.., my connection is working on winXP(just plug the cable and that's it). How to connect my suse 11.2 to internet? I tried to setup in YaST --> Network Settings
********************************** Code: OUTPUT OF "lspci":
linux-1c1l:~ # lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
[Code].....
i have just installed a Fritz Wlan USB stick on a practically fresh Maverick 32 Bit install with ndiswrapper.(i used this guide [in german] [URL]...so far so well, problem is, i cant enable the wireless. As far as i can see, this is no "on-button" issue. The build in wireless is either dead or never been there. It shows in the output below, but the "wifi-on/off" button doesnt do anything to the LED thats supposed to turn on and in an case... no connection. I think basically what my problem is that i can't figure out how to enable the wireless (its greyed out in the network-manager) i also installed the 32Bit version of the driver on a 32Bit Notebook. below is some output of what i found on other threads to try:
[Code]...
I have a Broadcom B4312(I believe) wireless card and installed the drivers for it, but under the Wireless tab in Network Connections, it doesn't show "wlan0" or anything similar to "eth0"(which it shows under "Wired"). I ran iwconfig and this is what I got:
[Code]....
I'm having some trouble getting my Zyxel NWD271N usb wireless adapter to connect.I'm using Ubuntu Desktop 64bit 10.10 What happens is that i'm always asked to enter the wpa key, and i've double and tripple checked that it's entered correctly. The wierd thing is that it has connected once or twice, but lost connection quickly, but i saw that i got an ip. I'm not sure about the maximum range on the adapter but i would estimate the distance to be no more than 4-5 meters from the wireless point. Also the signal indicator on the list of wireless networks shows strong, if not full. when i run lsusb i get:
Code:
Bus 001 Device 007: ID 0586:3417 ZyXEL Communications Corp. NWD271N 802.11n Wireless Adapter [Atheros AR9001U-(2)NG] when i run lsmod |grep ar9170 (saw the command on a german forum so i didn't understand what was talked about, but i got that it was about the same adapter) i get:
Code:
ar9170usb 54294 0
mac80211 267163 1 ar9170usb
ath 10413 1 ar9170usb
[code]....
I hooked up router to tower and ever since I have not been able to get PeoplePC WebMail. I unplugged router and I still can't get the web mail. The customer support have stated web mail is down other reps say it is not. I get the internet. I have Ubuntu installed.
View 3 Replies View RelatedI picked up the computer for free (Dell P4 with no HD), stuck in a hard drive I had laying around and installed Ubuntu Studio 10.04 yesterday. I am completely clueless about how to do anything with Linux. I put in a Zyxel g-360 wireless pci card, and found the ACX111 driver online. I found the wiki here: [URL] Are those installation instructions? I can't understand what it says. I have the Zyxel installation disk for Windows XP if that helps.
View 9 Replies View RelatedI have managed to compile and install the driver for my linksys AE1000 adapter. I can scan and see my network (and several others) but can't seem to connect. I have read a few threads looking for clues but I can't seem to figure it out. My kernel is 2.6.35-24-generic and I am using the latest rt3572 driver (v2.5.0.0). Here are a couple of steps that I have taken:
1) The usb driver does work properly and connect on a Windows machine.
2) Temporarily removed security from my router (uses WPA2). Still can't connect.
3) Tried compiling and installing the previous version of the driver (2.4.0.2)
I would like to access my NSA-220 Plus through the Internet without having computer turned on. I tried to set it up as a FTP server but I was not successful. I tried few tutorials but all allow me to access NSA-220 Plus only within my home network which is not what I want. Also I tried user manual which does not really tell you how to do this.
View 2 Replies View Relatedi need to build an ipsec vpn between a linux debian server and a zyxel prestige, The debian server got 2 ethernets connection one for the internal network and the other one is public with a public ip adress.I need to know what i need for the build the tunnel, could you please let me know what i need? Let me explain i have only to configure openswan or i have to configure the iptables or somethings else too? I found this one do you think this would be work for me? [URL]..Is debian a right distro or should i try someone else?
View 2 Replies View RelatedI am trying to attach shared files to a Thunderbird mail.The files are stored into a remote machine inside my LAN. The path is something like smb//:<something>But when trying to attach the file I get a permission error:"controllare i permessi di accesso al file"(trad: "check the access permissions to the file")
View 1 Replies View RelatedI have been a predominant Windows user for a long time but shifted to Ubuntu recently. I was just trying out a few basic C functions when i realized that the "conio.h" header file isn't included in the libraries and therefore i was unable to use the "clrscr()" function.
I downloaded a tarball which contained the necessary library and header files including conio.h. Once extracted, i specified the location and included in the program as " #include "path to the header file" ".
I still didn't call the "clrscr()" function, and it compiled successfully. Next i edited the program to call that function and it gave the following error...
How i can add new libraries in the future?
Just recently built and setup a new PC for my Dad running Kubuntu 11.04 64bit. As always, I installed and configured the latest Firefox (v5) as the default browser and appropriate plugins such as Flash (64bit using flashaid), adblock plus, video download helper and download status bar.
Everything is running fine, except for we are unable to attach files in Gmail. Further testing returned the same results in Hotmail also.
When composing a message, then clicking 'attach file', the file browser windows as per normal. However, when attempting to navigate to the required folder to select a file, when clicking on the folder to open, the file browser 'attached' a link to the folder.
I was able to replicate this on a 2nd machine with almost identical software setup. I then tried Konquerer (sp?) on the 2nd machine and was able to correctly navigate, and attach the file as needed.
I never noticed this problem before as I use Thunderbird on my all my systems.. but am able to replicate it on 3 different systems.
I have an Apple Airport Extreme dual band router, with a 2T hard drive plugged into the USB port, formatted with FAT32. Both Mac OSX and Windows 7 automatically see the drive and all the files on it, but unfortunately, I can't get Ubuntu to really see that drive. It sort of shows an icon under network, but if I try to open it, I don't see any files in it.
I have a very unaltered off the shelf installation of Ubuntu 10.10 on a Sony Vaio, some sort of AMD dual core vintage. I never thought that it would be Linux that failed to see the router drive, but unfortunately, that is what has happened.
I have a Linksys router configured via Windows 7 and have to other PC's using Ubunto, and would like to share folders on the 2 Linux boxes with the Windows Laptop. I can see the windows network through the Linux machines but not vice-versa. I also have a Konica 1400W printer connected to the Linux box but can't get the W7 laptop to find it.Sharing message box states I haven't installed the correct sharing packages, but cant find them
View 2 Replies View RelatedI have 2 machines both using U 11.04, one of them being Studio. I have tried to connect them together (via a modem/router of course) to browse files but I can't connect. I get error messages. I've installed samba and everything.
View 1 Replies View RelatedAfter been convinced by an exchange student from Nashville I am hosting here in Germany I went into openSuse 11.2. I installed and got openSuse 11.2 to work. I must admit, that I was very impressed. It is more than 10 years that I tried a UNIX system and Linux was quite a cryptic thing. First some additional drivers had to be installed to get MP3 to play. However Internet access was possible with cable but the system failed in recognizing the WLAN.
Here is my system:
HP Compaq nc4000
OpenSuse 11.2 (i586)
KDE 4.3.1 "release 6"
Wireless Network
Atheros AR5212
I have looked through some posts but must admit, that I did not understand much of that. I Am willing to learn, however I do not see myself compiling some drivers. If you could tell me which URL could be used for dloading or installing via Yest, If more sophisticated solutions, than I will have to ask my student to do it for me, but he should learn German and learn more about German lifestile in German Bars.
i dled ubuntu 9.10 and i got it ready on ma pc but after the setup process is done i couldnot get it attached to my LAN or internet connection i use a DHCP router wich need no configuration as it was shown problem is even my acctivity lamp on da router doesnot give any activity light btw i got some records as
[code]...
I'm using wpa_supplicant to get wireless working on my HP nc6320.Following that article how-to-install-intel-pro-wireless-3945-on-centos-linux) I was able to use wirelesssince 5.1 but when I've upgraded from 5.2 to 5.3 there some problem came with wpa_gui:[root@localhost]# service wpa_supplicant startStarting wpa_supplicant: /etc/wpa_supplicant/wpa_supplicant.conf -ieth1 -Dwext Device eth1 kernel driver name: ipw3945 [ OK ]
[root@localhost]# ll /var/run/wpa_supplicant/
total 4
srwxrwx--- 1 root wheel 0 Apr 5 20:50 eth1
[code]....
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies View RelatedWhat's the best desktop search for Meerkat? I need one that indexes Evolution eMails as well as filesUsed to use Tracker, but it seems to have changed in Meerkat.
View 1 Replies View RelatedI installed 14 and no ifcfg- files. (no ifcfg-eth0)can i create them ??
View 6 Replies View RelatedHow to refresh and reload the list of email into MUTT ? Which key?
Additional: how to go to folder SENT of gmail ? and configureation eventually?
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
I am coding some scripts for sending via irda to my PDA with another irda that has a triggering on the remote control. OK. What I would need is as follows. With MUTT, I configured it so that I can read my emails with the IMAP and gmail. It is cool. It is working with the last
Code:
mutt --version
mutt: invalid option -- '-'
Mutt 1.5.20 (2009-06-14)
which is annoying with "--" but ok, it works. I would like that a script export the last 10 emails to 10 x TXT files with in it:
[Code]....
These r IP provided by my ISP that i've put on Fedora 8:
WAN IP:xxx.xxx.xxx.17 (eth0)
Subnet:255.255.255.252
Gateway:xxx.xxx.xxx.18
Valid static(public) IP set of 2:
IP:xxx.xxx.xxx.147 & 148 (eth1, eth2)
Subnet:255.255.255.240
i want to run xxx.xxx.xxx.147 as a web server & xxx.xxx.xxx.148 as a ftp server. but I'm able to ping only xxx.xxx.xxx.17(WAN IP) from outside world. Can any1 tell me that how can i bring my 147 & 148 IP online without router.
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
i need to install an Zyxel G220 V1 which is a wireless adpater.I plug it on the usb and the dmesg i have this:
[ 2025.463349] usb 1-1: firmware: requesting zd1211/zd1211_ub
[ 2025.469375] usb 1-1: firmware: requesting zd1211/zd1211_ur
[ 2025.493491] usb 1-1: firmware: requesting zd1211/zd1211_uphr
[Code]....