Ubuntu Networking :: AE1000 Installed But Can't Connect To Router?
Jan 5, 2011
I have managed to compile and install the driver for my linksys AE1000 adapter. I can scan and see my network (and several others) but can't seem to connect. I have read a few threads looking for clues but I can't seem to figure it out. My kernel is 2.6.35-24-generic and I am using the latest rt3572 driver (v2.5.0.0). Here are a couple of steps that I have taken:
1) The usb driver does work properly and connect on a Windows machine.
2) Temporarily removed security from my router (uses WPA2). Still can't connect.
3) Tried compiling and installing the previous version of the driver (2.4.0.2)
View 5 Replies
ADVERTISEMENT
Nov 6, 2009
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
View 12 Replies
View Related
Mar 14, 2011
I'm new to fedora and also new to Linux too. I'm using lenovo SL410 which is not provisioned for serial port. Now I want to configure cisco router via serial-usb (Z-TEK) converter, for that I have installed minicom and still I'm not able to connect to router. Do I need to install driver for converter that I'm using?
View 2 Replies
View Related
Apr 6, 2011
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....
View 5 Replies
View Related
Aug 1, 2010
My son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
View 2 Replies
View Related
Jun 19, 2010
I hooked up router to tower and ever since I have not been able to get PeoplePC WebMail. I unplugged router and I still can't get the web mail. The customer support have stated web mail is down other reps say it is not. I get the internet. I have Ubuntu installed.
View 3 Replies
View Related
Feb 18, 2011
Here is the situation: I am currently running Ubuntu 10.10 64 bit. I'm trying to get my Linksys AE1000 to run correctly. I have followed many tutorials but most notably was:[URL].. lsmod shows that rt3572sta is loaded. network manager in gnome is able to find my router. my problem occurs when it tries to connect to the router using wpa2 security. It continually asks for the wireless password then will freeze the system after a number of attempts. After digging in for a bit, I was able to dig out a dmesg trapping the error:
BUG: unable to handle kernel paging request at ffffcfb0138af1ec
IP: [<ffffffffa021c7e8>] Cntl0idRTBssidProc+0x78/0x570 [rt3572sta]
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/cpu7/cache/index2/shared_cpu_map
CPU 2
I really don't see the need to continue on with those error messages lsmod still shows rt3572sta after the failure. In case anyone wants to see the changes I have made to the files before the make, I have included them. but changed the extension to "txt" to accommodate the up-loader and my rt_linux is too big to fit here, just not that it was 2 lines that were changed to work with the kernel. If anyone wants to know what I mean by the system freezes, I do mean just that. The mouse will continue to work, but I am then unable to open any programs, unable to reboot the computer. it requires a hard reset.
I have uninstalled the drivers, installed them, make them, make install them, make clean, start from scratch a few times, and am getting no give here.
View 7 Replies
View Related
Mar 6, 2011
Alright yall, I just got my wireless usb device to work on ubuntu 10.10. I did alot of searching and I finally figured it out. this is what I did.
1.Download the linux drivers from this post, its called Ralink_RT3572USB_drv2400.zip
2.Extract them to a directory.
3.Make sure you have build-essential installed on your computer. you can do this by opening a terminal
and typing
Code:
sudo apt-get install build-essential
4.Now install linux headers so that you can compile the drivers.
Code:
sudo apt-get install linux-headers-$(uname -r)
5.Now in your terminal goto where you extracted the Ralink_RT3572USB_drv2400 files.
once in that directory type
[Code]...
View 9 Replies
View Related
Jul 29, 2011
I recently purchased the Linksys AE1000 wireless USB network adapter. After some struggles, I found and installed the Ralink_RT3572USB_drv2400 driver for it and it now works, however it won't turn on when I boot up the computer. I have to manually unplug and then plug the adapter back in for it to work again. I followed the instructions on this how to for installing the driver.
[URL]
View 2 Replies
View Related
Feb 5, 2010
My problem is little different then what I've seen here. I get the same message after inputting network name and password. I click connect and it just pops up again I don't get it. I'm running Ubuntu 8.10 for Ppc (PS3) I get no internet connection what so ever just the same message. The message I get is " authentication required by wireless network " What do I need to do to connect wireless to my router with my PS3 using Ubuntu 8.10? It does connect with a Ethernet Wire. I am new with Linux.
View 1 Replies
View Related
Feb 16, 2011
I have a AE1000 wireless adapter and Ive been using it or about 4 months on windows xp. Yesterday I installed ubuntu 10.10 and it won't work It won't connect to the internet and won't even show signs that it is turned on.
View 5 Replies
View Related
Feb 6, 2010
I have a router with 2 IBM Thinkpads connected. One Thinkpad is running Ubuntu, and the other is running XP.
They connect to the router with no problems.
I installed Ubuntu on a Sharp Moebius laptop and plugged in the network cable.
NOTHING.
I have tried pinging the laptop; nothing.
I am not sure where the problem is, because my Thinkpads have no problems connecting to the router, with both Ubuntu and XP
View 9 Replies
View Related
Apr 22, 2010
my LAN just suddenly stopped working. we had a power outage, and it just stopped. it will still recognize the network, but it wont connect. i was experimenting with setting up a web server (trying to set it up on the standard distro). i know its not the network card (on board) because i can put in my pci card and it still wont connect. it will connect when in the live environment. i thought that maybe it had updated, so i tried to boot from a different (older) kernel. that still didn't help.
i stopped apache. i was experimenting with portforwarding at the time (i had everything else working on my server), but i could not get it to work. after this happened, i restored the original settings on my router. i had applied the settings only a day before the power outage. everything still works on another computer on the network (also running linux). (all computers run 9.10) its almost like my router won't assign me an ip address.
View 9 Replies
View Related
Jun 23, 2010
I have a new belkin N1 router which I tested in somebody else's flat. It worked fine. When I got home I reset it by pushing a paperclip in the hole for 10+ seconds to erase this flat's internet connection settings (username and password and stuff). After this I plugged it the computer and tried to connect to it (wired connection) using 192.168.2.1 (this is correct for that router, it is not 192.168.0.1). But the browser says it is offline and cannot connect. The lights of the router cycle, the "modem router" light blinks continuously and the others briefly come on and go off again, every few seconds. I tried resetting it again, several times, leaving it off for a few hours, leaving it on for a few hours, etc.
View 2 Replies
View Related
Sep 5, 2010
I recently just upgraded my operating system to Ubuntu 10.04 LTS and I can't seem to get my wireless card to connect to our new Verizon Actiontec router. I am using an Encore Electronics 802.11n Wireless USB Adapter (model: ENUWI-N), which had worked with an earlier version of Ubuntu and our old router. The adapter recognizes the SSID of the new router but will not connect with the correct WEP key or even with the encryption turned off. I have tried deleting the wireless profiles and manually re-creating them and still no dice. I have also gone to the website of the chipset manufacturer and found the latest drivers (RT2870USB(RT2870/RT2770)) for the adapter, which, according to the Synaptic Package Manager, I do not currently have installed.
Where do I go from here? Do I need to install the new drivers, and if so how do I do that?
View 6 Replies
View Related
Oct 23, 2010
I wanted to try Ubuntu again but have gone wayback to an old 8.10 disk because I couldn't get 10.10 to work. The install with 8.10 went fine but the internet will not connect. The network manager shows eth0 grayed out and when going in to manage the connection it says 'never'. I'm using Vista with a broadband modem connected to a netgear router.
View 3 Replies
View Related
Nov 1, 2010
Im trying to setup Ubuntu for my buddy. After talking it up for ages of course i get a problem ive never seen be for . He is running 10.10 (or whatever the newest is lol) and when running windows it hooks up to the internet just fine through the router. however in ubuntu it will only connect when i plug it directly into the modem. Route gives no output. Kinda weird. router is Linksys Wireless G Broadband Router. WRT54G.I dont want him running back to windows before he even gets into it.
View 4 Replies
View Related
Nov 20, 2010
new to ubuntu and having difficultly connecting to my wireless router.It can see the router but will not connect keeps asking for password.usb adapter is working 100% as i can connect with it using xp 64bit.
View 4 Replies
View Related
Feb 3, 2011
It says my routor's name and signal strength but when I try to connect it tries for a while and then fails.
View 1 Replies
View Related
Mar 15, 2011
I think I have unique problem. I have a d-link DWL G510 rev c.(Austrailian) WiFi card in my pc which is detected as
Quote:
Network controller [0280]: RaLink RT2561/RT61 rev B 802.11g [1814:0302] in lspci -nn.
iwconfig shows:
Quote:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=6 dBm
Retry long limit:7 RTS thrff Fragment thrff
Power Managementff
ppp0 no wireless extensions.
Now sometimes it detects my wifi router and shows its ssid in nm-applet. but when I try to connect, it tries for 3 or 4 minutes and then fails. for most of time it even does not finds my router.
View 1 Replies
View Related
Mar 17, 2011
I have installed ubuntu 10.10 and am really happy. I want to sort the wireless conection out now. I have been through this forum for hours today and can't get it working. I have a Broadcom wireless card, which seems to be working fine, but I am not 100% convinced.I have attached the output of some of the commands that I have seen referred to on here.
I am using the wired connection on the same router, so the router connects fine.I click on the network icon and I see the skyNNNN router in the list. I have tried connecting to it and it asks me for my password, which I provide then nothing happens until it asks me again.I have removed the security from the router and I then see the same skyNNNN router without a
lock icon. I try to connect and it still fails.I am not using an access list on the router, so there is no issue with the mac address.
View 7 Replies
View Related
Apr 14, 2011
I have been using pppoe connect to Internet,now I want my notebook get on line,I bought a wireless router but Ubuntu(64-bite) can't connect to Internet through the wireless router.pppoeconf said that found eth0 and vboxnet0,but search concentrator failed and pppoeconf exited.How can I fix it.
View 1 Replies
View Related
May 19, 2011
I'm running Ubuntu 10.04LTS 64bit. The desktop running it does not connect to my router or the internet. My mac laptop does. When I installed windows on this desktop, it too could connect. But after reinstalling ubuntu, I cannot. I tried upgrading to the latest ubuntu, but that just bricks my computer. Here is my ifconfig:
Code:
~$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1d:09:95:39:76
inet6 addr: fe80::21d:9ff:fe95:3976/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1492 Metric:1
[Code]....
View 9 Replies
View Related
Jun 20, 2011
I have just installed 11.04 alongside windows vista. I have been trying to connect my router but it keeps saying disconnected from network. I have ran all of the troubleshooting tips in ubuntu its self and everthing seems in order. is there any settings i need to change on my router or in ubuntu's edit connections programe? I managed to connect to the router once to upgrade from 10.10 to the 11.04 but even before upgrading to 11.04 i had problems connecting to the router.
View 6 Replies
View Related
Jul 4, 2011
I'm having a problem with my RTL8187 wireless card using NDISwrapper The problem is that I can't connect to my home router I tried everything and it won't let me Suggesting changing my security settings to WPA is not valid because my retarded brother won't let me do it, so is there anyway I can connect to this router??
View 1 Replies
View Related
Jul 6, 2011
Just installed ubunto 1104 and I cannot connect wirelesly to my router. When I go through the trouble shooting the recommendation is to got to the device drivers page but the link does not take me anywhere. Here is the info from the terminal.
*-network DISABLED
description: Wireless interface
product: AR9287 Wireless Network Adapter (PCI-Express)
vendor: Atheros Communications Inc.
[Code]....
View 7 Replies
View Related
Jul 8, 2011
I have two Ubuntu 11.04 machines connected via cable to the same D link ADSL router. how do i connect one to the other so i can see from the other computer files and transfer them using nautilus?
View 9 Replies
View Related
Sep 18, 2009
I'm trying to connect to a new Belkin wireless router, but wicd refuses to connect. I've been reading some of the other threads but they haven't made much sense as the hardware is different.
The output from the iwconfig command is as follows:
When I ran lspci it told me I had a RaLink RT2800 802.11n PCI Network Controller. On the box it says it "Supports the most popular systems" and mentions Linux. I'm using a 63 character WPA2 password, which has been copied from a USB key, so I know that is correct.
View 2 Replies
View Related
Apr 9, 2009
I am net to this whole Linux thing. I cant seem to connect to my Linksys router. Not sure if I have to call Linksys or what.Mine is a WRT54GS
View 1 Replies
View Related
Jul 8, 2011
Ok so I tried to follow the directions here: [URL] However, I couldn't find 2010_0915_RT3572_Linux_STA_v2.4.0.2.tar.bz2. Instead, the closest I could find was 2011_0407_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2 .5.0.2_DPO.bz2, so I tried it. I edited config.mk and rtusb_dev_id.c as chili555 advised. I tried to edit linux_rt.h, however, the only file I saw was rt_linux.h. I edited it according to chili555's post, message #7. I went back to the root directory of the extracted .bz2 file and did
[Code]...
View 5 Replies
View Related
