I have a few computers on my home network and I want to get them running at 1000Mbs Both my Ubuntu Machine and my Mac already have the hardware to run at that speed but my switch is 100Mbs so I am going to buy a new 1000Mbs switch. Do I need to change any settings in Ubuntu 9.10 to allow for 1000Mbs networking?
View 1 RepliesI have two onboard gigabit connections and a PCI-E gigabit card, none of which seem to want to run beyond 100M. Everytime I issue the command to change speed to 1000M, it does nothing. I have tried modifying the interfaces file to make sure the command line for ethtool gets done automatically, but still no luck.
Below is the output from the use of ethtool to change speed. Since I am having performance issues with my local area networking (e.g. Samba transferring slower than the internet), I have been trying to figure out how to debug my network performance, and this was an obvious thing that stood out. The router and card are gigabit, yet don't use their full transfer rates.
[Code]...
I got this Acer Revo 3610 nettop about a week ago. I got it to use as an htpc, and decide to do an install of xbmc live on it. I have everything set up the way I want it at this point, but I'm stuck on trying to configure the wireless.
I'm not sure where I should start troubleshooting this thing, but something about this seems off to me.
Code:
xbmc@XBMCLive:~$ sudo -s
root@XBMCLive:~# iwconfig ra0 mode Managed
root@XBMCLive:~# iwconfig
lo no wireless extensions.
[Code]....
I have 1000 jpg files in which all have a white background. Is is possible to change the white background color to red (for example) of all the files in order not to have to do it one by one ?
I would prefer to use Linux but I can handle Windows.
For example, change this Logo with white background to red background.
i have a computer with 3 users on it, and a folder using samba that everyone on the network has access to. Lets say that, the folder is stored in /etc/sharedfolder. What happens is, when user1 puts a folder in it, then logs off, user 2 attempts to modify it and fails, because permission is set to 755, and they are not in the same group. (even if they were, it should still need to be 775) Anyway, my current solution is, every 5 minutes a crontab changes permission like so: chmod 777 -R /etc/sharedfiles && chown useradmin:superadmin -R /etc/sharedfiles Which works, but seeing as there is getting close to a gig in there, this is a bad solution, as it eats up the computers resources. Solutions that i think might work:
1) create a script that only changes permissions that need be changed.
2) change file permission settings to force all documents to inherit parent document settings
My college providers shifted to a different setting.. I'm not sure what needs to be done. On windows, under the connections tab you need to change the proxy settings and put in the IP address and enter the port to 3000. Questions:
1. where lies the linux (ubuntu 10.04) variant to execute the operation.
2. What can be the major obligations of such a change?
I am sure its siimple enough, but I can't get my net to work properly. The connection provided to the internet is through wireless routers.
I have a router that is 1000 Base T and two computers each with ethernet cards that support 1000 Base T. All are equipped with Cat 5e cable. Before I had a router that only went up to 100 Base T and I would setup one box with linux running proftpd. On the other box,I would use win xp pro and use firefox to ftp into the other box and download a file. Download speeds went up to 11.2 MB/sec. Now when I switched routers, I expected something like 120 MB/sec but I'm only getting 5.3 MB/sec. What do I need to change?
View 12 Replies View RelatedI currently have a Windows XP OS which i want to dual-boot with Ubuntu Linux 10.10 . I put the disk in the drive and chose the option to install Linux through Windows. But it hangs in the middle. I am also unable to change my BIOS settings due to which i can"t change my boot preference. My first Boot is the HDD. I want to change it to CD-ROM. Any suggestion? I also have another PC where i can boot through the CD...I tried installing there by booting from the CD but i get this error message after seeing the purple Linux screen with the loading dots. "(Process:286):Glib warning**:getpwuid:failed due to unknown user id (0)
P.S.- I am not able to see any options while the boot is going on
I am having trouble establishing a connection with my WPA wireless network at home. Other laptops at home can connect to this network and even the Eee PC can join free wifi networks. The problem seems to be only with WPA networks. When I enter the password for the WPA network, it tries to connect for a while and then shows me the password dialog box again. I don't get any IP during this time, its always 0.0.0.0 I reinstalled my Ubuntu netbook remix but that didn't help. This problem was occurring in the standard Ubuntu 10.04 too.
View 2 Replies View RelatedI am trying to get the RT2860 card in an Eee PC 1000 to work. I have tried Ubuntu 8.04 and 9.10, all the "fixes" below I can find on the web but nothing seems to work.
[URL] I downloaded the source code from Ralink and using module-assistant followed the instructions.
I can see the wireless network, it tries to connect but just keeps asking for the security key. I have tried WEP, WPA and no security at all but still no go. All works fine if wired. The F2 toggle seems to work OK, the WLAN is switched on in the BIOS. The "iwconfig" command shows the RT2860 in Ubuntu 9.10 but not in Ubuntu 8.04.
I'm operating a server running Slackware 12.1 and I need to install a PCI-E 10/100/1000 NIC, im just wondering if anyone has any recommendations for a card that has solid support under linux or is otherwise known working.
View 1 Replies View RelatedI have just installed Ubuntu 10.04 and the wireless connection on my Asus EeePC 1000HE is not working.
Network is seen but connection is always rejected and pops up the dialog requesting my password. Password is entered properly and using proper protocol (WPA2)
Network is working perfectly under Windows 7 and Fedora.
I use ubuntu netbook for an eee pc 1000h because windows is underpowered. I got it working perfectly in 10.04. I upgraded to 10.10 thinking, if they got it right with 10.04 then surely 10.10 should be fine. All function keys except wireless work.
1. After sleep, wireless turns off. Have to restart and re-enable in bios.
2. If I disable and the re-enable wireless networking it tries to connect but never does resulting in a reboot needed. Checking bios wireless is enabled and connects perfectly on reboot.
Just don't close the lid and sleep because you need a restart. Why would 10.04 be easy and the new version fail? I am windows user and linux does not do this kind of thing normally. MS screws things up with upgrades not linux surely.
env: debian kernel 2.6.31/ gcc 4.x/ hp6910p I encounter a problem whilst trying to connect online using Intel PRO/1000 nic, but fail. It seems the problem of nic (Intel PRO/1000 'e1000e').
dmesg | grep e10001 shows
Code:
Intel(R) PRO/1000 Network Driver - 1.0.2-k2
PCI INT A -> GSI 22 (level, low) -> IRQ 22
pci_enable_pcie_error_reporting failed 0xfffffffb
irq 29 for MSI/MSI-X
dmesg | grep eth0 shows
[Code]...
What should I do so that I am able to solve this issue or does any resource/ doc tell how to configure e1000e to enable Intel PRO/1000 nic?
I installed the netbook version of ubuntu 10. Problem is no wireless networks show up. So I have an eternet connecting. Only problem is when I plug that in, still no internet. I need to download drivers to make the wireless work.
View 1 Replies View RelatedI have a Broadcom NetXtreme BCM5754 NIC and I cannot seem to get the NIC to auto link at Gig speeds. It will only link @ 100/full.
View 1 Replies View RelatedI've already got the b43-fwcutter package and a driver called 'b43' appears in System > Administration > Hardware Drivers but it does not seem to enable. Another, Broadcom STA wireless driver, does enable, but I'm not picking up the wireless signal.
Code:
$lspci 05:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01)
08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Code:
$ sudo lshw -C network
SCSI
[Code]...
Have been using Ubuntu Desktop Amd64 for 6months, on a dual boot alongside Vista64. Since first installing the OS, I have switched over to Ubuntu & use Windows only for heavy multimedia edition & the occasional gaming.I just bought a netbook and installed Ubuntu 10.04 LTS NBR. Works great, except for wlan. No propriety drivers available for my Intel Wifi Link 1000BGN.
I've spent hours trying to install iwlwifi, but the process is somewhat complicted for a noob such as myself.After much reading and trying, I've managed to download and install iwlwifi-1000-ucode-128.50.3.1.tgz, (following the http://intellinuxwireless.org/?p=iwl...=howto-iwlwifi instructions)and am now working on installing the mac80211 subsystem (following the http://intellinuxwireless.org/?p=mac...howto-mac80211 instructions)When running
Code:
% wget
intellinuxwireless.org/mac80211/downloads/mac80211-10.0.4.tgz[/url]
[code]....
I recently had my AE 1000 linksys wireless adapter driver installed, the info for which can be found here:
[URL]
But today I was presented with 142 automatic updates already downloaded waiting to be installed on my computer. I installed the updates and restarted my computer for the updates to take effect. Well, since then my wireless adapter no longer registers at all, it doesn't even recognize my router let alone connect to it. It is as inoperable as the day I got it.
I am currently using a different computer in the house to get internet. Should I go about following the same directions I did before and reinstall the driver, or is there a more simple way?
My wireless card is:
Code:
03:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0083]
On Fedora 15, when I boot kernel 2.6.40, my laptop is unable to connect to my wireless-G AP. dmesg shows the following:
Code:
[ 43.866090] wlan0: direct probe to 00:27:19:14:c2:ca (try 1/3)
[Code].....
It works fine, however, when I boot using kernel 2.6.38 (from which I am posting) and in Windows. Also, I found some emails from the linux-wireless mailing list which appear to be talking about the same problem.
The system is fully updated. I've tried the 11n_disable=1 hint I came across on the ThinkPad wiki, but it didn't help. (I'm on an Asus K42Ja, in case it's relevant)
Although I'm fine with staying at 2.6.38 for now, are there workarounds/fixes for this?
I have Ubuntu 10.10 on a thinkpad X201. Wireless was working, but has stopped. It still works in windows, so it is not a hardware problem. iwlist wlan0 scan sees the available networks, but I cannot associate with any of them, including my own.
Last night was my first attempt to connect to a secured network, and nm-applet failed to make the connection even after entering the WEP encryption key and SSID. By turning networking off in nm-applet I was able to manually bring up the connection by editing /etc/network/interfaces and using ifup wlan0. (nm-applet seemed to be interfering as long as networking was turned on there.) Wireless was working perfectly until I rebooted. Now I can't get it to work at all. (There were some partially completed security updates which completed when I rebooted. I hope this wasn't the cause of the breakdown.)I notice that wpa_supplicant is always running. I tried killing it in case it might be interfering with the connection process, but something keeps restarting it.
My Intel Corporation WiFi Link 1000 Series wireless card stopped working yesterday after I did an update via Update Manager.After the upgrade, wireless is disabled and the option to enable it in Network Manager is grayed out. I thought that it might be the new kernel, but changing back to the old kernel I still have the problem.
View 8 Replies View RelatedTried to Google an answer but it seems the 'System' menu options have changed in 10.4 compared to older versions.I want to chnage the auto-run settings so that each time I enter a CD, Rhythembox DOESN'T load but SoundJuicer DOES
View 1 Replies View Relatedwhen I installed 10.10 I chose ask for password on login but I want to now just be on when I turn on the computer without asking for a password. how can I do this?
View 3 Replies View RelatedI received Ubuntu 10.10 (a friend gave me the cd) Well, I installed, but I can't change the display settings: the maximum it gives is 900x600 So, I went online and looked for a fix.. I found this:
Code:
Sudo dpkg-reconfigure x server-xorg
Well, the problem is that according to the steps that the person who posted the code, I should type this code after executing Terminal before computer boots. and the way to execute Terminal is to have the key: escape holded Well, I do hold the key: escape. but I see no terminal! I have typed in normal mode...but, I guess the code only works before boot up. How can I execute terminal? is there any other way to fix the display settings? I currently have Windows Xp and Ubuntu.... and I have no problem with the display settings on Xp Can I do do from recovery mode?
Because I have 2 operating systems I get a screen like this (except mine is ubuntu 10.10) If I do it from the recovery mode.... would the code works?
I am having ubuntu 9.10, but I need to add user that have right to change network settings only. how to do that task ?
View 1 Replies View RelatedI'm trying to move a file to opt folder. But I cant do it because I dont have the permission to do it. In folder preferences it says " you are not the owner"How can I move a file to opt folder? or How can I change the folder permission settings?
View 8 Replies View RelatedEditing the profile in gnome-terminal has absolutely no effect on the appearance. I can change background color, transparency, image, etc. in the profile edit window, save changes,and the _actual_ terminal appearance does not change at all. I did make sure to switch to the edited profile after editing -- to no avail.The default navy-on-light-blue isn't bad, but the light-green default for executables is effectively completely invisible on the light blue background.Is this a bug? Or does someone have a workaround?FWIW, gnome-terminal in 9.10 was completely customizable
View 3 Replies View RelatedI have installed the new Ubuntu 10.04 LTS and do not see where I can change the toolbar icon settings such that I only display icons, not text labels beside the icons. Does anyone know how to fix this?
View 2 Replies View RelatedOn a Dell 14n, 10.04. Mic problem: To use the mic jack/external mic, I need to have MIC 3 selected at SYSTEM/PREFERENCES/SOUND/INPUT To use the built in mic, I need to have MIC 1 selected
How can I get these mic's to work w/o having to change the settings each time I want to switch mic's.. so that if the mic jack is plugged in, then the external mic works. and if the mic jack is unplugged, then the built in mic works.