Ubuntu Networking :: Sharing Internet & Connecting Ethernet And Wireless?
Jan 13, 2010
I tried to setup sharing to connect Ethernet and wireless. I want Ethernet connected to desktop A, and wireless connected to another laptop(B), with my laptop acting as an AP. I set the network settings in Firestarter: Internet for wireless, local network for Ethernet. I want to share Internet from laptop B over the network. Internet won't work from my laptop since it seems to use the wrong interface.(Since the desktop is sharing Internet, although not on Internet usually when connected via Ethernet. And of course DNS/Gateway IPs aren't set for wlan0 since it's acting as an AP.) SMB wouldn't work for desktop A and laptop B: laptop B could detect desktop, but reports error "Path not found".
View 2 Replies
ADVERTISEMENT
Jun 21, 2011
I am running Ubuntu 11.04 and i am curious to if there is a way to share my established wireless connection through my Ethernet port.. I know it was possible in Windows by going to adapters and bridging the wireless, and Ethernet adapters. how to make this work in Ubuntu?
View 1 Replies
View Related
Dec 26, 2010
just recently I made the move back to Ubuntu from Windows. Upon re-installing I noticed a problem with me connecting to the internet. Previously on Windows I had updated my Ethernet Adapter driver, upon installing I would have to disable and re-enable the device to let my computer have access to the internet. My problem here is how would I go about fixing this on Ubuntu so I can have internet access on Ubuntu
View 1 Replies
View Related
Jan 16, 2011
I just want to use Internet Connection Sharing (ICS) to connect to the internet. I have done a massive amount of troubleshooting, but some of it seems to contradict itself, and the only two things that I know for sure are that it used to work, and that my Ethernet cable is not the problem. When I use Terminal utilities like ifup and dhclient it seems that it can not determine IP information, but when I try to put it in manually, the "Apply" button grays out right after I finish typing it in. When I try to connect normally, in KDE or GNOME, the icon acts like it's connecting, then instead of having the connected icon, I receive a notification that "the network has been disconnected", and it goes back to the disconnected icon.
Oh, and by the way, I know that I could probably find a workaround, but I have limited resources, and this used to work. The Linux is a Dell desktop with Fedora 12 and the Windows is a Windows 7 HP laptop.EDIT: I hope that I didn't mess something up, but I accidentally used system-network-config to try putting in the IP address there, and ended up changing it back to the original settings, but the computer is now calling it Auto Ethernet in the taskbar icon, although sudo iwconfig in the terminal still calls it eth0.
View 7 Replies
View Related
Jun 25, 2010
I would like to have all traffic from the ethernet connection out through the wireless (basically using the box as a router) however I am having some trouble doing this.
I have done this before on Windows however I am having some trouble doing this on linux, I have tried using Squid Proxy however I am having some trouble using configuring/using it.
I am using Yellow Dog Linux however I am willing to change to any other distro as long as it is compatable with PS3 (as this is what im using linux on)
View 14 Replies
View Related
Dec 10, 2010
Using ubuntu 10.10 (pinguy OS) i connected an ethernet cable from my girl's macbook pro to her lenovo ideapad s10-3t to transfer some DS9 episodes onto it. new enough to linux to have not been able to figure out how to access the files on the mac, so i disconnected the ethernet, and the wireless hasn't worked since. tried everything i know, and googling for a while (as well as searching again on this forum) to no avail.
Just before linking the 2 computers via ethernet, the wireless worked fine on the ideapad, always had; but not so after the ethernet connection that did nothing other than apparently kill the wireless. an "lshw -C network" command tells me i have a BCM4313 wireless card, and *-network UNCLAIMED. also, if i launch "install additional drivers", i see that the proprietary driver is not active.
How could merely plugging in an ethernet cable that happened to be conncected to a MBP running OSX.6 do that? and will that happen again? i thought linux was supposed to play real nice with other OS's, so why did a simple file transfer kill my wireless connectivity? i have no access to internet via ethernet cable, so i cannot just download the driver i need now. shouldn't it still be in the computer still? somewhere? is there a simple solution to this, or has the wireless driver been wiped out by plugging in the ethernet? is this a bug that should be reported?
View 3 Replies
View Related
Feb 16, 2011
i have a Levano S10e intel atom preccessor and the net-book is not connecting wirelessly to the network. i have tried at two locations and even plugged in a exterlal wifi adapter. it wouldnt connect then either, the only way to get connected is to use a cat5 cable. here is the ifconfig output with no cat5 inserted and it not connecting to the internet.:
[Code]....
View 8 Replies
View Related
Aug 29, 2010
For the last 3 or so hours I have been trying in vain to simply give my mobile phone wifi internet access from my netbook. I have tried to google and follow some howto's and guides, but they're either too old or don't explain it very well. I'm fairly new to use of Linux and of wireless networks, but can handle setting them up in Windows. So basically, having said that, I believe I mostly understand how this whole thing is supposed to work theoretically but I just feel as though I lack the experience to jump the wireless hurdle AND the Linux hurdle at the same time. I have provided some information below.
- Setup is based on Lucid netbook remix install with a Maverick kernel update due to lack of driver support for wireless NIC - I can confirm wireless does work properly for connection purposes
- I followed [URL] and kind of followed [URL however I couldn't even tell how to run Network Manager, even though Synaptic tells me it is installed
- When I ran into problems trying to install ipmasq I found [URL] and followed what the response told me to which allowed me to restart the dnsmasq and the dhcp3-server at least
- I have restarted the entire netbook several times throughout the process.
View 8 Replies
View Related
Nov 3, 2010
I am trying to establish an adhoc connection in my ubuntu 10.10 and share my cable internet throughout this connection with my Android phone. I have read some guides but I couldn't be successful. (I have another windows mobile, and it couldn't connect too). I have installed Firestarter in order to enable internet sharing. My main Problem is that, no one can obtain IP adress from the adhoc connection, whether Firestarter is active or not. What should I do in order to make the other devices gain IP address from this connection. If I have to set static IP what should I do exactly?
View 9 Replies
View Related
Jul 22, 2010
I have a wireless Internet modem (USB) and a LAN Ethernet connection. I can only pick 1 of them to connect to (by disconnecting the other). How can I connect to both at the same time?
View 6 Replies
View Related
Jan 22, 2010
I'm connecting to my wireless, but I can't connect to the Internet, not even via an IP address.
(*) Can not open web pages via IP address.
(*) Can ping internal hardware no problem.
(*) I can connect to the Internet via Ethernet no problem.
(*) I used to be able to connect via wireless on this computer. No settings changed in the interim.
(*) Several other computers currently connected & accessing Internet via the same wireless - no problem.
(*) Based on other posts, I disabled the avahi daemon, but this had no effect.
Outputs of some commands:
[Code]...
View 8 Replies
View Related
Jun 8, 2010
I have never seen this before but to connect to the internet either wired or wireless I have to connect to a broadband connection as well. I am currently using wireless; I connect to ISP with wireless but in order to access the internet I have connect to the wireless connection through my broadband connection(This is where I enter a user name and password.). I'm not sure why this is, I have always just plugged an Ethernet cable in and the computer just knew I guess.
I am using ubuntu-10.04-netbook-i386.iso that I had put onto a USB drive. It booted fine, but when I tried accessing the internet I couldn't. I was able to connect to the ISP, but I couldn't find any settings for a broadband connection. My computer is a Acer Aspire One Netbook 250
Intel Atom
CPU N270 @ 1.60GHz
1.60 GHz 1.99 GB of RAM
Network Adapters
Atheros AR 5B95 Wireless Network Adapter
Atheros AR8132 PCI-E Fast Ethernet Controller
View 3 Replies
View Related
Jul 9, 2011
I have a wireless router, but my desktop computer is connecting to it, or maybe to the modem, by an Ethernet cable. It has a built-in wireless card, so just as an experiment, I tried to connect to my network wirelessly. It didn't work. And not only did I not get any internet connection, I can't get any internet through the wired connection either. The internet works fine with Windows Vista (I'm dual-booting), as well as when I boot up Backtrack off of a Live DVD. I can still access my router's config page by going to 192.168.2.1 on a web browser, but I can't access anything else.
View 1 Replies
View Related
Jan 1, 2011
I have internet access through 3G/4G USB dongle direct into my Ubuntu 10.04 box. Works great! Now I would like to share this connection out through my Netgear WGR614 wireless (and wired) router. Any clues? I've tried the simple (GUI) instructions using Network Manager, but just can't seem to get it right. Previously, I had DSL and this plugged nicely into the WGR614 and internet and ethernet access was had by all. Now, I'm a bit confused on how to get the sharing (ethernet and wireless) between my Ubuntu box and the wired/wireless network while at the same time getting Internet access to all through the Ubuntu box.
View 2 Replies
View Related
Mar 4, 2011
I am wanting a computer with an external dialup modem (ppp0 modem through a com port /dev/ttys1) to act as a gateway to the internet, forwarding internet traffic through ethernet (eth0 is set to static 192.168.2.2) to a router (the router is 192.168.2.1) where it will be broadcast to other wireless computers like my laptop (192.168.2.3). I've had this setup until recently when the gateway computer (the one with the modem) died. Now I'm replacing that machine with another box and an install of Ubuntu 10.10 but so far things aren't working for me.
Success so far:I have dialup access working on the new box. Took me a while to work out the configuration for getting dialup working, though the IP address is Dynamic (or it won't stay connected), "Check carrier line" is off, and "Ignore Terminal Strings (stupid mode)" is on in order to successfully connect and stay connected to my ISP. I also had to make my normal (non-root) user "lancer" a member of the "pid" group (the reboot) in order to use gnome-ppp as non-root. The laptop (192.168.2.3) is successfully connecting to the router (192.168.2.1) as I can see the router configuration page when I type http://192.168.2.1 into the laptop's web browser. This setup is unchanged from how I had it before when this was previously working and I don't want to change how the router itself is set up. What I want is to know what to fix in the new box in order to get it connected to the router (through ethernet) and bridging the internet through.
My problem is that whenever I plug in the eth0 from the gateway (192.168.2.2) to the router (192.168.2.1), Ubuntu's automatic plug-me-in network detection kicks in and I find my dialup no longer working through some kind of IP conflict (at least that's what I think it is). Maybe I don't have the "gateway" correctly assigned? (in the gateway computer for the ethernet connection, I had it pointing to itself as I don't know what to put for "gateway IP" as that is automatic So, just to check my connection, here I am pinging google (from the gateway computer which has the dialup modem) once a dialup connection has been made.
Code:
lancer@lancer-desktop:~$ ping www.google.com
PING www.l.google.com (74.125.237.17) 56(84) bytes of data.
64 bytes from 74.125.237.17: icmp_req=1 ttl=55 time=179 ms
64 bytes from 74.125.237.17: icmp_req=2 ttl=55 time=176 ms
64 bytes from 74.125.237.17: icmp_req=3 ttl=55 time=158 ms
[Code]...
What do I need to do in order to make Ubuntu of my gateway computer stay connected to my dialup but also simultaneously share an ethernet LAN to my wireless router and feed traffic to the other computers from there? I have googled this but some of the most promising instruction (e.g. http://www.ubuntugeek.com/sharing-in...in-ubuntu.html) call for packages like dnsmasq or ipmasq which seem defunct now in Ubuntu 10.10. Other pages seem to suggest dual-networks "can't be done" in Ubuntu [URL].. (what!?! I had it before my other gateway died)
View 1 Replies
View Related
Aug 6, 2010
i'm having problems connecting to the internet unless i manually enter the IP info.
automatic DHCP does not work. I'm on a dual boot machine vista/ubuntu 10.04 LTS connecting to the internet through a lynksys wireless g router and a cable modem.
View 2 Replies
View Related
Oct 11, 2010
I just installed Fedora Core on my Dell Inpsiron B130 laptop and I am having trouble connecting to the internet both wirelessly and with an ethernet cord into the router. When trying to configure my network, I dont recognize any of the ethernet adapters in the drop down list. I have been told that my wireless card is Linux compatible (dell y8029 dell wireless 1370 802.11/a/b/g mini pci). My ethernet card is a B130 Broadcom Ethernet Driver which isnt in the drop down menu either.
I read that I need to download an ndiswrapper but I dont know where to find this download AND even if I could download it to a zipdribe, I have trouble opening a USB flash in Linux becuase its not a "valid block device". This is after the command "mount /dev/sda1 /mnt/usbflash"
View 4 Replies
View Related
Jul 18, 2010
My PC is connected directly to the cable modem. I would like to use my PC's WiFi card to share my internet connection with my Android phone and laptop so I can avoid buying a wireless router.
View 4 Replies
View Related
Mar 6, 2011
I have Ubuntu-laptop with wireless card wlan0 and wired ethernet card eth0 and windows7-desktop with wired ethernet card.I want my desktop PC to connect to the internet via ubuntu wireless card. Meaning that, I'm connected to a wireless internet network in my ubuntu pc and I want to share this connection to the desktop.
[URL]
View 1 Replies
View Related
Feb 9, 2010
I just installed Ubuntu 9.10 and its great. However when I connect to the internet at home it shows that the connection has been established but I still cant connect to the internet. My flatmates are all able to connect. However, I am able to connect from work both wirelessly and through an ethernet cable.
View 2 Replies
View Related
Mar 22, 2011
Heres the set up I have: one eeepc running ubuntu netbook. with a usb wifi dongle, this is connected to a parabolic antenna i made out of pizza boxes and tin foil. One fujitsu laptop running ubuntu 10.10. the eee connects to the internet via the dongle. then the laptop connects to the eee. I set this up by using network manager. I created a new wirless connection and called it "UbuntuAdhoc". The on-board card connected to this without issue and the laptop was able to connect to the new wireless broadcast by the eees on-board card.
This worked perfectly untill I rebooted the eee. Now the eee is unable to conect to the internet if the on-board caard is conected to "ubuntuadhoc". also the dongle now wants to conect to "ubuntuadhock" too.
View 1 Replies
View Related
Sep 1, 2011
My laptop was working fine on wireless till the userinterface changed and it defaulted to ethernet and now it won't let me go back on wireless How do i disable ethernet?
View 4 Replies
View Related
Apr 26, 2010
My computer needs the boot option "noapic". Unfortunately the Ethernet doesn't work. It does work when I use the boot options "noapic acpi=off" but the printer that is connected via a parallel port does not work. Also I have to push the power button the system is shutting down with this option.
Output of lspci:
Quote:
View 1 Replies
View Related
Jan 11, 2011
I have two computers, a laptop and a workstation, both running linux (Ubuntu and Fedora).For some reasons, it's handier for me to work from the laptop, accessing the workstation only from remote.At present, I have to connect to the workstation using a very complicated system that implies VPN + ssh passing through the internet. It works, but it would be far easier and faster if I could set up a direct connection between the two computers. Unfortunately, I can't use the ethernet ports or wi-fi (it's a long story why, but I really can't).I own a usb data transfer cable, but I don't know how to use it.
View 1 Replies
View Related
Apr 27, 2011
I've been doing some reading and I cannot work out why I'm having this problem. My 32-bit Ubuntu Server running 10.10 has a Realtek RTL8111 ethernet card which supports up to 1000mbps. However, when I run sudo ethtool eth0 I get:
Code:
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
[Code]....
After running sudo ethtool -s 1000 to try and change speed to 1000mbps, the output is still the same as before. Why is this :S?
View 9 Replies
View Related
Jan 17, 2011
The Wired Internet adapter isn't working with Ubuntu 10.10, and without this working, I can't get my updates for the Broadcom WLAN adapter. I have a Realtek RTL8101E/8102E PCI-Expredd Fast Ethernet controller. I have looked for solutions, but haven't found any relating to my problem.
To be specific: Ubuntu 10.10 is recognizing the Ethernet adapter as eth0. When I try to manually connect after inserting an Ethernet cable connected to the Internet, it tries for a couple of minutes before telling me the adapter's been disconnected. The connector lights remain the same on the port as they always were.
View 1 Replies
View Related
May 25, 2011
I'm trying to set up a wireless AP with Internet sharing. I currently have the AP setup with hostapd and a dhcp server. The clients can connect but there is not Internet sharing. Now my situation is somewhat uniqe in that my internet connection is my teathered android cell phone. The tether app is azilink and i use openvpn to create a virtual networking interface(tun0).
View 4 Replies
View Related
Aug 19, 2011
I have just installed Ubuntu and I'm having trouble connecting to the Internet. I have a wireless USB adapter that worked while I was using Vista, but now it doesn't.
View 5 Replies
View Related
May 16, 2010
I was trying to configure wireless network on my ubuntu machine but could not do it. I am possibly stuck as I don't know much about configuring things on linux platforms.
View 8 Replies
View Related
Jan 31, 2010
So I've been trying to install OpenSUSE on my laptop. The installation went smoothly and then the trouble comes: connecting to the internet. It seems that every time I run a KDE based distro, I have trouble connecting. I've done everything I can think of (which wasn't much): I've run the YaST and tried setting it up that way. I've tried using the terminal and iwconfig to no avail.
View 1 Replies
View Related
