Ubuntu Networking :: Running 9.10 (i386) With Latest Patches From Update Manager
Jan 21, 2010
I'm having problems installing Cowpatty
running make produces
cc -pipe -Wall -DOPENSSL -O2 -g3 -ggdb -c -o md5.o md5.c
md5.c:20:25: error: openssl/md5.h: No such file or directory
md5.c: In function md5_mac:
md5.c:28: error: MD5_CTX undeclared (first use in this function)
md5.c:28: error: (Each undeclared identifier is reported only once
md5.c:28: error: for each function it appears in.)
[Code].....
Running Ubuntu 9.10 (i386) with latest patches from update manager. If I try using the 4.2 archive I get the same result.
I have similar problems with aircrack-ng suite, but I'll leave that until later!
View 5 Replies
ADVERTISEMENT
Sep 30, 2010
As the title says i updated my system which then needed a reboot. I also installed Mixxx djing software to try it out. So i thought id just restart the system. Usually when i boot into my desktop wireless automatically can connect to my router but not this time, wired only for now... i know theres tons of wireless issue threads but some more experienced users will be able to get straight to the point and run through some diagnostics with me.
View 1 Replies
View Related
Sep 25, 2010
When I try to update the latest from Update Manager I get this message:
Please insert the disk labeled: Ubuntu 10.04.1 LTS _Lucid Lynx_ - Release i386 (20100816.1) in drive /cdrom/
I'm running 9.10. I don't know why I'm getting this message, does anyone here know why this is happening?
View 3 Replies
View Related
Jun 25, 2011
The latest update totally screwed up my system on KDE.The KDE network manager says "activating network", "networking system disabled", "connection failed".The icon shows 3/4 progress completed and is stuck there. Any attempt to change connection manually leads to plasma-desktop crash. I know this is only update related because I have messed with system earlier and thought that the network failure could be my fault, so I reinstalled the system and ran only update command, after the reboot the system was again in the fubar state. This is really frustrating. Just feels like really poor update testing. I have Fedora installed on three different systems however, I won't update them until the problem is fixed.
View 10 Replies
View Related
Mar 13, 2011
after initating the update and i enter my pass word, update stops and an error box comes up stating that it is unable to update because there is more than one synaptic manager running, i have restarted and get the same results, and to my knowledge there is nothing else running in the background.
View 3 Replies
View Related
Apr 7, 2010
Installed from the 9.1 iso got everything set up all tickety boo. using it as a local development server. have been ignoring the update manager, but today for some reason I thought ok, do your thing fatal on restarting it gets as far as the splash screen then dies " * could not access PID file for nmbd" hit esc to get the grub thing up and tried recovery mode same deal so stuck really.
I can hit 'e' and get a basic emacs thing wit a few lines of commands, but not sure what to do there!
I'm not a big terminal user. I can do stuff I need to and leave it at that. Do I have to flatten this machine and re-install anything. Loathe to do that as I spent quite a while getting all the webby bits installed and working as I want to, adn don't really want to have to set all that up again.
View 2 Replies
View Related
Apr 12, 2010
I got the following error window (screenshot attached) while running Update Manager. What does it mean?
View 1 Replies
View Related
Feb 5, 2010
I can't tell if its my computer or just the internet? I'm just running the GUI Update Manager.
View 7 Replies
View Related
Mar 26, 2010
While running the update manager my system froze and all that I knew to do was power down and power up again. When I first started the update said 18.5 MB and on restart it said 17.x MB. I restarted the update manager and it failed with errors.
The last message says "E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover:" but no progress in 1/2 hour. If I try to copy the messages to the clipboard it says that cntl-c will abort the operation so I haven't done that. From the top of the "Details" there are about eight "Invalid archive signature" messages. I don't know how to proceed.
View 7 Replies
View Related
Mar 27, 2010
I'm re-posting here since I've gotten no response in the Installation & Upgrades Forum.
While running the Update Manager my system froze and all that I knew to do was power down and power up again. I restarted the Update Manager and still have errors.
The original thread is at: [url]
This is not a crisis. I can re-boot and run without apparent errors. I thought about apt-get -f install but I don't understand enough. Is this a broken dependency problem? If this is a dependency problem will this (apt-get -f install) just clean-up the loose ends and then will the Update Manager pick up the pieces the next time I go through "check"? Is there possible harm doing this?
This system is at 9.10 and was up-to-date until I had this problem yesterday.
View 1 Replies
View Related
Jan 7, 2010
I was running the Update Manager when my system froze due to the failure of Karmic to support motherboards using the Intel 845 chipset.
Although the update did not complete when I rebooted and invoked Update Manager it reported that the system was up to date. How do I reset the system so that I can install the updates?
View 1 Replies
View Related
Feb 18, 2010
I'm a little bit stuck and in need of advice from people who know what they're talking about. I've had Ubuntu on my office PC, home PC and laptop for about a year now and never had a problem that I couldn't solve, until now. I'd not turned my laptop (Lenovo N 500 with Ubuntu 9.10 64 Bit using GRUB2) on for about a month so when I did on Monday of this week I noticed that I'd not updated Ubuntu for 27 days, so ran the update manager. After everything was updated I carried on using it as normal but when I tried to turn it on yesterday I get the following issue...
GRUB loads and gives me all the possible boot options. Whatever one I choose, I get the same results. It starts to boot (I see the black screen with the white Ubuntu logo) but this remains on the screen for a very long time, then it goes to a flashing cursor at the top left of the screen and it just sits there indefinitely.
I've tried playing with Super GRUB Disc but admittedly I'm not too sure what I'm doing with it. I've tried using the Ubuntu Installation disc as a Live CD too but with no joy. The main HDD appears fine when in Live CD mode, all my files are there etc.. Is this actually a GRUB issue or something else? It's like GRUB's doing its bit and then it's failing slightly further down the line.
I'm totally out of my depth here and really don't want to have to reinstall everything, I'm sure there's a simply solution.
View 9 Replies
View Related
Jan 28, 2010
Which latest perl is suitable for Redhat AS4 i386 system?where do I get it from?
View 2 Replies
View Related
Jan 10, 2011
Is there a script which will take the patches subdirectory of the latest Slackware distribution tree, and substitute the new patch txz files for the ones in the slackware subdirectory so that during an ISO install, the latest txz will be used, instead, and the ISO will be minimized by not having the older ones?
View 6 Replies
View Related
Jan 9, 2010
Creating a new thread for the specific chipset. Laptop is an Acer 5534 with the Atheros chipset. Normally uses the Ath9k driver. To get it to work originally I had to download, compile and install the latest compat_wireless drivers. See post here: {URL] I did the update that came through today and after the reboot there was no wireless internet. It alternates between reboots between having no wireless networks at all detected to never connection to the [AUTO] network previously defined. To fix the problem, I downloaded the latest compat_wireless, compat-wireless-2009-12-11.tar.bz2, and followed the same procedure. I did not do a make clean. To solve the problem temporarily, I edited the grub config and set default to 2 instead of 0 (1 would be 0 in recovery mode).
View 1 Replies
View Related
Feb 1, 2010
i have a acer aspire one (zg5) with a 2 week old installation of unr. shortly but not immediately following my last update my wifi no longer functions. when i go to the network connections tab in my toolbar it does not list available wifi networks. does not apparently recognize wifi capability at all. but the wifi worked right off the rip on new install.
View 3 Replies
View Related
Jun 1, 2010
I updated this morning to the latest bugfixes for F13. For some reason, networking has become un-available after the required re-start. I am using a fixed IP. Tried to add eth0 DHCP, which initially worked, but became unavailable after a few minutes as well. I suspect there may be an issue with the card's MAC address which may or may not be detected correctly.. Has Networking been updated somehow in this bugfix release?
View 2 Replies
View Related
Sep 1, 2010
how to update patches in fc12.
View 2 Replies
View Related
Apr 18, 2010
I have a Lenovo IdeaPad s10 which worked flawlessly with wired, I could never get it to so much as search for a wireless network, so I gave up on it long ago.
I'm using UNR 9.10 on it and today, after updating Wicd Network Manager stopped working making it impossible for me to go online with the netbook even when using a wired connection.
I restarted the computer after the update and once UNR booted up wicd wanted root access to use my computer's network cards, I entered my password, this never happened before but whatever, unfortunately after I entered my password wicd didn't show up in the tray and sure enough there was no internet connection whatsoever.
I tried running wicd manually, UNR says opening, but nothing comes up, no tray icon no nothing.
View 3 Replies
View Related
Oct 30, 2010
On my ageing laptop with Intel IPW3945 wireless adapter which has always worked extremely well.... Fedora 13 with the latest NetworkManager. Seems that wireless speed has slowed to a crawl.
Code:
[glenn@leonardo ~>$ rpm -qa | grep NetworkManager
NetworkManager-vpnc-0.8.1-1.fc13.i686
NetworkManager-pptp-0.8.1-1.fc13.i686
[code]....
View 6 Replies
View Related
May 15, 2015
Is there any way to get update notifications for security patches on debian jessie. I was using update-manager and update-notifier and wheezy and that worked good, Update-notifier on jessie doesn't seem like its working...
View 12 Replies
View Related
Jan 19, 2010
I am having issues with Update Manager after cancelling an Update.The Update Manager shows a number of required updates, but when I click on Install Updates... Nothing happensWhen I launch sudo dpkg --configure -a in a terminal I receive the following message:dpkg: status database area is locked by another process.On another forum i saw something regarding a gksu.lock file that needed to be deleted... but I can't find any such file....If I try to launch update manager via a terminal: sudo update-manager I get the following error:
requiredDownload could not be calculated: E:Unable to parse package file /var/lib/apt/lists/us.archive.ubuntu.com_ubuntu_dists_karmic-updates_main_binary-amd64_Packages (2), E:Unable to parse package file /var/lib/apt/lists/us.archive.ubuntu.com_ubuntu_dists_karmic-updates_main_binary-amd64_Packages (1), E:Unable to parse package file /var/lib/apt/lists
[Code]....
View 9 Replies
View Related
Apr 22, 2010
I had network manager running on my netbook karma install, but when I installed VNC as another display, logged into that other display and accidentally clicked on not to run network manager on startup cause there is already one running, it screwed up the network manager auto startup on my normal netbook display.I tried adding it back into auto start in settings but that has not worked.As always, thanks for any help you can give me getting this to auto start again on login, without deleting my kde cache(cos it is setup the way I want it).
View 3 Replies
View Related
Mar 22, 2011
I am a bit new to this - Ubuntu is ok with a gui but I am struggling with commands and I think I may have disabled Network Manager. The icon is there in the notification area but when I try to connect it says NetworkManager is not running and when I rightclick the icon the "enable networking" box is greyed out. It is on a desktop which now has no net access so I have not tried to remove and reinstall network-manager.
View 7 Replies
View Related
Jul 13, 2010
Ubuntu 10.04 64 bit I have not been able to update using the update manager or by using the package manager. It seems when the update manager tries to download all the requests fail.Anyone else had this problem??
View 1 Replies
View Related
Jan 4, 2010
I used Ubuntu for the first time yesterday (V.9.04) and imediatly upgrade it to V.9.10. After,the DSL conection failed to conect. After reading many threads here I was able to connect by opening a terminal:
sudo pon dsl-provider
It seems ther's a bug with network-manager, but I'd like to use it again as it easier and NB user-friendly.
View 1 Replies
View Related
Jan 6, 2011
Arg, I just removed the bad update 2. 6.35-24.now update manager wants me to install new ones; is it still the 'bad' update that messed up my wifi or has it been fixed?
View 4 Replies
View Related
Dec 10, 2010
I was having trouble getting update-manager to work behind a proxy (without authentication). I tried everything I could find in my search, including setting http_proxy environment variable, setting the System->Preferences->Network Proxy and setting the Synaptic package manager proxy settings. Nothing seemed to work.
It turns out that the problem was that the System->Preferences->Network Proxy allows "automatic" proxy (pac file), and I had used that. update-manager doesn't do anything with this setting I guess. I changed from the automatic setting to a host/port manual setting and it began working.
I suspect this qualifies as a bug. update-manager should do something more reasonable than quietly fail if the settings are for automatic - it would be really nice if it worked, and if not then an error message.
View 5 Replies
View Related
Mar 9, 2011
Writing this from a 9.10 LiveCD, so I know that my hardware is working fine.My system is running 10.10 normally. Last night, the update manager popped up, as it frequently does, and said I had some packages that could be updated. So I let it update after which it said I needed to reboot. So I did, and now it doesn't recognize my network connection, and even the blinky lights on the port itself stay dark. don't know a lot about networking or stuff under the hood, but I can work a console and/or text editor if someone can tell me where to look and what to type.My hardware is (from "lspci | grep -i eth"):02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)The packages that have a modified date of last night are:
ubuntuone-client-gnome_1.4.6-0ubuntu2_amd64.deb
python-ubuntuone-client_1.4.6-0ubuntu2_all.deb
libsyncdaemon-1.0-1_1.4.6-0ubuntu2_amd64
[code]....
View 9 Replies
View Related
May 27, 2011
Using Ubuntu 10.04 (2.6.32-31)on a Dell studio today.Update manager offered four updates, one about networking. I accepted. After restart the Network-Manager icon had vanished from the tool bar and was replaced by a second loudspeaker control icon. No ability to link to the internet. Starting Network-Manager from the pull-down menus did not help.Muggins Noob thought, un/re-install Network Manager. Duh! Uninstall is fine, but re-installing from the web without Network-Manager, tricky. Sadly no ethernet wire available, either wifi or GSM/3G.
View 4 Replies
View Related
