OpenSUSE Wireless :: Network Detected But Will Not Connect?
Feb 16, 2010
I have a D-link dir-635 firmware v. 2.30eu (latest) and a USB WLAN adapter D-link DWA-140 802.11n. The driver seems to be installed correctly since lsusb lists it correctly and all the wireless networks in the vicinity are detected including mine. When I try to connect however NetworkManager says it is activating but after awhile the windows with the newtork password appers. dmesg output:
[ 5509.487262] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 1
[ 5509.684014] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 2
[ 5509.884020] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 3
[ 5510.084014] wlan0: direct probe to AP 00:1c:f0:71:03:88 timed out
So it is able to determine the AP:s mac address but each time it times out.
I have tried disabling the security on the router but no luck.
Not sure what to try next. I have checked some of the tips supplied in these forums but none seem to handle the issue I am having.
View 7 Replies
ADVERTISEMENT
Jul 17, 2010
an issue with my broadcom wireless that is using the bcm4312 driver. I installed the b43(?) cutter firmware from the command line and now my network is detected but it just won't actually connect to it. My router has wpa security enabled but i think it worked with it before.
View 9 Replies
View Related
Mar 14, 2009
Wireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
View 4 Replies
View Related
Oct 27, 2010
1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
View 9 Replies
View Related
Mar 23, 2010
When i click the button to connect to a wireless network this message apears:Network management disabled
View 1 Replies
View Related
Apr 17, 2010
at start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
[Code]...
View 2 Replies
View Related
Apr 13, 2010
On Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
View 5 Replies
View Related
Sep 30, 2010
I've got openSUSE 11.3 running via liveUSB on a netbook and no matter how many times I try, I cannot get wireless to connect to my network.
My network is:
- non-broadcast
- WPA2 Personal
- G
The netbook is fairly recent from Asus and wireless works perfectly with Fedora 11 and Windows XP.
View 5 Replies
View Related
Apr 8, 2010
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies
View Related
Nov 5, 2010
I'm moving from other distros. and I'm currently loving openSUSE and I'm probably going to stick with it for a long time.I have already googled for this, but I found no solution, but I figured this should be a common problem... Does google searches inside this forum?Now... for my problem, whenever I hibernate (suspend to disk) or sleep (suspend to ram) I can't resume my wireless connection nor connect to another.I don't know if this is an issue if I use cables, because I simply don't with my netbook:The hardware in question is an ASUS 1005HA eee pc, running openSUSE version is 11.3 fully updated. Didn't mess with wireless connections, nor kernel or hibernate settings
View 9 Replies
View Related
Mar 10, 2011
After installing 11.4, I need to type in the command to update the firmware for a broadcom wifi adapter. Then I needed to reboot, twice, before the system knew to use the adapter (where the adapter wifi light goes from orange to blue).
Then I needed to add my wireless network and type in my key. But the key does not take. If I click on my wireless network icon, it just re-asks for the key and does not connect nor give any other message. Network icon continues to display no connection.
So I need to reboot again.
When the system starts again, the adapter is blue, I click on the icon for my wifi network and it connects without asking for my key and I can then set to start my wifi by default.
Now my wifi works fine.
View 1 Replies
View Related
Apr 15, 2010
All settings are correct as far as i can tell. The wep key works on all my windows boxes. When i have connect automatically enabled it never tries to connect. if I go to edit it it pops kde wallet up i put in credentials. wallet goes away then nothing happens. if i double click connection to my router also nothing happens. I have the wep key in there and i even made it visible to make sure.
View 5 Replies
View Related
Aug 9, 2010
I am using OpenSuse 11.3 and Network Manager is giving me a headache by not connecting to WEP based wi-fi network.It works in a wi-fi at my office while at my home, it shows / detects the network but keeps asking me over and over.
View 3 Replies
View Related
Apr 11, 2010
One of the biggest issues i have at the moment is that my network based plasmoids on my KDE desktop load before my wireless network connection is established, so i'm thinking it would be best to start up the wireless connection at boot time. On previous distro's, I did this with netcfg but I can't seem to figure out how to do so in OpenSUSE 11.2. Is this the best way to manage this issue or is it possible to set a delay before the plasmoids load up?
View 5 Replies
View Related
May 24, 2011
I just installed opensuse 11.4 and i'm not being able to connect to my wireless lan. It recognizes my network, but when I click "ok" after typing the password it is like I had done nothing, no connection is set at all.I guess it is probably some configuration stuff since my notebook recognizes all available wireless networks. Sorry about the lack of details, but that is all I got.
View 6 Replies
View Related
Jan 12, 2010
i've installed openSuse 11.2 on my laptop (dell studio 15).Today at work i tried to connect to the wireless network, but i couldn't. First, the network card wasn't being recognized, but after a long time trying i was able to set it up, for this i used this command:
Code:
zypper in broadcom-wl broadcom-wl-kmp-desktop
So now, the networkmanager detects all the networks around, but i cannot (or i don't know
[code]...
View 8 Replies
View Related
Mar 27, 2009
I just installed OpenSuse 11.1 on a netbook via network install. It's a dual boot with windows XP. In XP, the wireless card works perfectly, but in openSuse, it never connects. It cann see the wireless networks available but it won't connect to my network!
I even tried this to no avail: Wireless will not work when dual-boot with Windows XP&Vista | SUSE & openSUSE
I'm using:
Asus EEE 1002 HA
Wireless Card: Atheros AR928X Wireless Network Adapter
WPA2 (although when I switched the router to WPA, it still didn't work)
The weird thing is during install I told it to test the wireless card and it worked, but now it doesn't.
View 9 Replies
View Related
Feb 20, 2011
i have a hp g62-b31ee laptop that wont connect to any ad-hoc network all the steps is absolutely right-as the book says -
the strange is it connects any non ad-hoc wireless connection and also the wired connections works fine.
PS:if any one wants to know here is my laptop:
Network interface
Integrated 10/100BASE-T Ethernet LAN
Wireless technologies
802.11 b/g/n
Bluetooth wireless networking
View 4 Replies
View Related
Apr 22, 2010
victor@linux-debn:~> dmesg | grep firmware
[ 8.769511] prism2_usb: Checking for firmware prism2_ru.hex
[ 8.769520] usb 3-1: firmware: requesting prism2_ru.hex
[code]....
View 6 Replies
View Related
Jul 19, 2010
While my wireless is generally working, there's one problem: I can't connect to my home network through it on my laptop. My desktop (which has an Atheros-based wireless card and is configured through ifup) connects just fine, as does another family member's laptop (also with an Atheros chip, but using NetworkManager) My laptop (With an Intel Centrino wireless chip), however, will not connect to the home router, though it can connect to public (unprotected) access points such as the one at my school. My home network is a private (hidden) network and also requires a WEP key to connect to and, as mentioned, works fine with several other systems running 11.3. I've attempted to use both ifup and NetworkManager and can't connect using either method. With ifup, the connection attempt just seems to time out during the connection attempt, while with NetworkManager, it doesn't even seem to try: I select the connection that I defined and click "Connect" and nothing happens after that. I'm using KDE and installed from the LiveCD
View 2 Replies
View Related
Sep 28, 2010
I am using an HP laptop dv8000 series FYI. I started with a fresh install of OS11.2. The first thing I tried was to connect to a network through the gui net manager. This got me nowhere (nothing detected). I then noted that the card was not getting any signal/not functioning. My card is enabled from on the laptop.
I connected my laptop via ethernet and executed this command:
Code:
sudo /usr/sbin/install_bcm43xx_firmware
which returned no errors and seems to have completed successfully.
Using the dmesg | grep firmware command I now get the following:
Code:
SuSE-Laptop:~ # dmesg | grep firmware
[41.246079] b43 ssb0:0: firmware: requesting b43/ucode5.fw
[41.268643] b43 ssb0:0: firmware: requesting b43/pcm5.fw
[41.320790] b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
[41.369098] b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
[41.591065] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
SuSE-Laptop:~ #
Now the option to enable wireless in my systray (I know wrong name) has become unselectable. Now what do I do?
View 1 Replies
View Related
Oct 5, 2010
I recently installed 11.3, I was able to get my wireless working. However only using the "traditional method with ifup", I could not connect with network manager. I remembered last time I installed 11.2, it was suggested that the wired connection was taking precedence, which was the initial reason I went the traditional route. I changed the wired connection to "on cable connection" and the wireless to "boot time" but still no luck. So are both methods fine and its just a matter of preference, I would prefer to use knetwork manager.
View 2 Replies
View Related
Nov 20, 2010
i have HP Compaq 6710b with Wlan Broadcom 4321AG i can't connect to network and i can't scan
View 6 Replies
View Related
Aug 23, 2011
I have BCM4312 Dell wireless 1397 WLAN mini-card.I run Code:sudo /usr/sbin/install_bcm43xx_firmware to install a firmware and know I managed to see all the networks I have around me, but I can't connect to any of them (using the correct password).
View 8 Replies
View Related
Sep 10, 2011
my problem is that i am only connect mi laptop dell inspiron n4010 to the internet wired or wireless only if reboot pc, doesn recognize any network if i turn on my pc and then connect wired or wireless..
View 3 Replies
View Related
Jul 15, 2010
I did a fresh install,I also enable the networkmanager.after installation,my wireless unable to connect to my router . when I click to connect , it prompt for password then after that nothing happen.
View 8 Replies
View Related
Mar 17, 2011
Desktop that has wireless built into motherboard worked in 11.3 (as best as I can remember, don't really use it normaly). Trying to connect to my wireless router (only one I have rights to).Wireless router is WEP with opensystem authentication, works fine for laptop (Windows)Networkmanager scans and displays local networks
Networkmanager shows:
acivating
setting network address
connection failed
[code]...
View 3 Replies
View Related
Apr 27, 2011
how to connect to internet via ADSL,and wireless. i am writing all these frome windows
View 2 Replies
View Related
Sep 2, 2011
I am unable to connect to a WEP-protected network. the Network manager log shows either a DHCP timeout, or a failure to associate. (attached below).Changing to WPA is not an option, as the network is not controlled by me. This is with the rt61pci driver for a Ralink 2500 series chipset.(Rosewill RNX-G300EX card)Manually forcing an IP does not result in a connection either. This is with the latest OpenSuSE 11.4, all patches applied. Router is a D-Link DIR-613, and I know the passphrase I'm using is correct because it connects both on my Android (what else?) phone, and my lappy when I boot XP.
Sep 2 11:12:02 Core2Duo-2400 NetworkManager[2160]: <info> (wlan0): supplicant connection state: associating -> associated
Sep 2 11:12:02 Core2Duo-2400 NetworkManager[2160]: <info> (wlan0): supplicant connection
[code]....
View 7 Replies
View Related
Apr 14, 2010
I am running openSUSE 11.2 and just recently my network has been down. I'm using Gnome, but using Yast to configure my network (I'm usually forced to use wireless as I travel a lot on my laptop). Usually, when I'm connected to a wireless network, it will show up as so in the Gnome start menu, but recently, it will only say Wired there, even though I have nothing connected to my ethernet jack. I can connect wirelessly to a home router, but cannot use the wireless in any other way. I have tried manually disabling the ethernet connection to no avail. Unfortunately I am limited in my linux knowledge, so I am kinda stuck here.
View 1 Replies
View Related
