I have a wired connection on the motherboard and a also a card for wireless communication.Wired connection works fine but my plan is now to setup wireless connection too.I was advised to use this in order to find installed network devices: sudo lshw -C network.Not sure, but I think it only reports details about the wired device. Is that correct?How could I get ubuntu to also find my wifi-card?
View 7 Replies
Okay currently I am using a a Belkin F6D4050v1 usb wireless n card on a 32 bit intall of ubuntu 9.10. I have already installed ndiswrapper and installed the the rt2870.inf driver and rebooted. But i still have no wireless. when I use the command "sudo lshw -C network" all i see is my pci wired nic card"lsusb" the ID of the card is "050d:935a Belkin Components""sudo iwconfig" sayslo no wireless extensionsetho no wireless extensions
View 2 Replies View RelatedOS: Ubuntu 9.10 Karmic Koala
Programs: Network Manager, Ndiswrapper, Device Manager, Terminal
USB Adapter: Linksys WUSB11 v2.8 Driver 4.10
Router: Linksys Wireless-G 2.4ghz
SSID: Doss
Security: Unprotected
Mac Address: Disabled
Whenever i use to type in lshw -c network it used to show details about stuff, but now when i do it it shows nothing.
Also i did whatever was in this thread
how to install windows wireless drivers
i restarted my pc and now i cant even see the wireless network! it doesnt even say enable wireless networking in the network manager!
[Ubuntu 9.10]
I was using my usb Alfa AWUS036H-v5 usb wifi card, and then after I rebooted, it randomly stopped working.. did some searching on the site, one idea was to do
Code:
sudo lshw -C network
which I did, and it shows my internal wifi card (iwl3945) working fine, but says my wlan7 (Alfa usb) as:
network* Disabled
Also, in the upper right hand corner, the antenna is greyed out and says "Device Not Ready"
I have got Ubuntu 10.10 on a Dell Inspiron Laptop. Can't get anywhere with wireless network. Tried a few bits of poking it blindly with a stick:
matthew@ubuntu:~$ lshw -C network
Warning: you should run this program as super-user.
*-network
Description: Network controller
Product: BCM4312 802.11b/g LP-PHY
Vendor: Broadcom Corporation
Physical id: 0
Bus info: pci@0000:0c:00.0
Version: 01
Width: 64 bits
Clock: 33MHz
Capabilities: bus_master cap_list
Configuration: driver=b43-pci-bridge latency=0
Resources: irq:17 memory:f69fc000-f69fffff
*-network .....
I reckon *-network DISABLED is a problem, I tried sudo ifconfig wlan0 up but that didn't work. The output of that and lspci are on the ubuntu side of my machine. I have also tried pressing my wireless on/off key (F2) but that doesn't work either.
I need a bash script to run ARPON for the connected network device, eth1 or eth2. (ethernet or wireless)
Arpon has an option (-o) to select the network automatically, but it only works for ethernet, hence i need this script. I've also tried running arpon for ethernet and wireless at the same time, but the arpon process running the inactive device will consume all of my CPU.
So, basically i need a script to find which device is connected, eth1 or eth2 and then to run arpon -d -i <device connected> (or something like that).
Is there an easy way to do this? code...
I've searched everywhere how to find the connected device via bash, but i couldn't find anything.
I have just installed Ubuntu 10.10 on a Dell Laptop. It has a Netgear WG511 (made in China) PCI wireless card but I cannot see any connections other than the wired one. Entering in lspci in the terminal mode and removing/replacing the WG511 shows (I think) that something is being detected in the PCI slot "Network Controller: Intersil Corporation ISL 3890 [Prism GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] rev 01". Is this the WG511 and, if so, how do I get it to be detected as a network device?
View 9 Replies View RelatedI have been working on this for a while now and am absolutely stumped. Basically, what i am attempting to do is make my ubuntu box into a gateway for my network. I have everything working thru hard wire, but I simply cant get the wireless to work. No matter what I do, I cannot get my wireless card to transmit an essid and allow nodes to connect. I have tried assigning it in the interfaces file (shown below), and I have also tried manually modifying it using the iwconfig command. Here is the topology:
eth1: internet WAN
eth2: ethernet out to LAN
ra0: wireless out to LAN
Here is a copy of my /etc/network/interfaces file:
[CODE]
auto lo
[Code]...
I have an nc8000 that gives a "104 unsupported wireless network device detected" error when I plug in my Intel wifi card that I acquired recently. Based on reading, this is a common HP problem due to non-native HP hardware. If I insert the Intel Pro card after the HP boot screen, 10.04 loads just fine and Ubuntu detects the card.
1) Machine Brand and Model (PC/Laptop): HP/Compaq nc8000
2) Wireless Brand, Model and Wireless Chipset: 02:04.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
3) Check interface:
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
eth1 unassociated ESSIDff/any
4) Check for modules:
Code:
Module Size Used by
binfmt_misc 6587 1
snd_intel8x0 25588 2
snd_ac97_codec 100646 1 snd_intel8x0
ac97_bus 1002 1 snd_ac97_codec
fbcon 35102 71 .....
5) Network configuration
Code:
$ *-network:0
description: Wireless interface
product: PRO/Wireless 2915ABG [Calexico2] Network Connection
vendor: Intel Corporation
physical id: 4 .....
6) Scan for networks:
Code:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
irda0 Interface doesn't support scanning.
eth1 No scan results
7) Ubuntu Version:
Code:
Ubuntu 10.04 LTS
8 ) Kernel/architecture (including 32 vs. 64 bit):
Code: 2.6.32-21-generic i686
I am trying to configure a Travelmate 2490 to connect to my wirelessr router, a TP-Link TL-WR941ND. It does not show up in the list when I use network manager. However when I look to see if there is a driver for my wireless network in the computer it seems to find one. I am quite a beginner so some basic troubleshooting would be great.
View 1 Replies View RelatedI was using ubuntu 9.04 and everything was working flawlessly with my network. The only problem with 9.04 is that it was unsupported and I couldn't install the packages I wanted to such as Cairo dock so I decided to upgrade to 9.10 which is a lot better. However I ran into a problem that I never had on 9.04. I cant connect to MY wireless network (my Belkin wireless card can detect networks but not mine) I have a netgear router WNDR3700v2 with WPA2 encryption. I thought that the encryption was the problem so I turned it off and ubuntu could still not find the SSID through the network manager. My SSID broadcast is on.
View 9 Replies View RelatedI recently installed the Maverick Meerkat distribution and am having problems getting it to find and connect to my wireless network. Additional info: I am using a Toshiba laptop and used the wubi installer to get Ubuntu.
View 9 Replies View RelatedTo start off I have a Rosewill rnx-n2x wireless adapter and a Dlink 4500 router. The problem is, the wireless network manager detects every wireless router in the neighborhood, except mine. I see this persons, and this persons, but no "My router Not yours". I even tried doing the hidden network setup and still nothing.
I have read that the rnx n2x isnt supported by linux, although I've seen solutions to make it work (which didn't work, mkdir command kept getting denied during make) link to what I'm talking about: [URL]. What I don't get though, is that if the rnx n2x isnt supported by linux, wouldn't I not be getting my neighbors connections to begin with?
I normally connect to a free wireless project, and did have a Windows box until yesterday when I installed Fedora 10. When I was using Windows, I was able to connect to the unsecured wireless network. Now on Fedora 10, the wireless card is working and is able to pick up signals but the signal strengths are markedly decreased and I am unable to see the network which I usually connected to.I really don't want to go back to Windows.
View 12 Replies View RelatedIm just after installing fedora 12 dual boot with windows 7. When I try to find my wireless network the laptop doesn't seem to picking it up. It works perfectly when I connect with a LAN cable.
View 2 Replies View RelatedI am unable to access wireless network from my notebook. My configuration is Dell i5, 4GB RAM and 1397 W-LAN and I have F13. I can still access Internet through Ethernet using a LAN cable but the network monitor doesn't show list of Wireless networks which my room mate's windows 7 machine easily detects.
If anyone needs more info please provide me the steps to perform to find that out
I just added a 2 port network card to a system that is running Fedora 11, but it is INACTIVE. I open the Network Device Control to activate it but there is no network ports in Network Device Control. It is empty.It looks like the system recognize the card and loaded correct driver.
View 4 Replies View RelatedI have installed Ubuntu 11.04 on my laptop. For some reason Wireless Network does not work any more (there was installed 9.04 before).
lspci says:
Code:
00:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
System->Administration->Additional Drivers doesn't list anything.
Everytime I to turn on my wireless device, and try to connect to a wireless network, i see the phrase " device not ready" greyed out, and not able to access a wireless network. i do not know what to do
View 6 Replies View RelatedI have used ubuntu in the past but had a lot of hardware issues with it and unfortunately moved back to windows (( BUT i have tried Ubuntu again and all seems to work great except wifi My wifi connection is sort of working because when i run SUDO IWLIST SCAN it does pull up all available networks. But in the network manager icon on the panel i left click but i see no networks and can't connect to anything. I WOULD LOVE TO keep Ubuntu and use it permanently but I must get wifi working or else this won't be possible.
View 4 Replies View RelatedHaving a hard time getting NM to detect wireless usb device: Linksys model WUSB600N. Here are a few commands I do know about.
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
[code]....
I'm running OpenSuse 11.4 with kernel (2.6.37.1-1.2-desktop i686) and KDE 4.6.00 "release 6".When I first installed the system the KNetworkManager found my wireless network. After entering my details it suddenly couldn't find it any more and hasn't found it since (even after re-install). My network is definitely working. I did try and set it up with ifup but it still couldn't find any network. Unfortunately I don't know anything about networks even less about wireless ones. Many thanks in advance.
View 9 Replies View RelatedI get the wireless working by executing
Code:
sudo modprobe b43
All good so far, but it's kinda tiring to execute that command every time I restart the computer, just to get internet access. Is there any way to make this command execute by it's own, when starting up the computer, like in the background or something. Or even better, to actually make b43 the default driver for the wireless. I've tried reinstalling both bcmwl, and b43, uninstalling bcmwl etc. But no luck.
I find any wireless networks, except mine. Moreover, my wifi works, because I can surf with the university connection.But the network works, because I can connect to it both with Windows and with Ubuntu.I have a Broadcom 4321 like wireless network card, opensuse 11.4 and the default network manager.
View 8 Replies View RelatedI finally installed openSUSE along side ubuntu and xp in my ThinkPad EDGENow I am facing issue with toggling the wi-fi, I had no such problem in ubuntu.Seems like there is some issue in the thinkpad-acpi module.I use fn+F9 to toggle the wifi, which toggles both bluetooh and wifi, but on openSUSE it only toggles bluetooth.acpi_listen in ubuntu gives me the below result when I press fn+F9ibm/hotkey HKEY 00000080 00001005but in openSUSE its blank but bluetooth gets toggled. dmesg from ubuntu:
Code:
$ dmesg | grep acpi
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[code]...
I am using RHEL6,and using mainbroad ethernet device PXE network install ..kernel using wireless device install automatic. I cant choose ethernet device to install RHEL6.how can I ignore wireless device when I using network installation?
View 2 Replies View RelatedI installed ZTE MF 626 modem in my F10 with kernel 2.6.27.12-170, i run usb_modeswitch and so far things happened normally. Watching through /var/log/messages it says that F10 detects two port device for this modem: ttyUSB1 and ttyUSB2, and in the sequence it disable port ttyUSB1 BUT Network Manager still set this port.I mean, when i connect via wvdial appointing to ttyUSB2 i get connection, but Network Manager fails to do it appointing to ttyUSB1. How to change device port in Network Manager?
View 1 Replies View RelatedI'm running the latest Ubuntu Desktop Edition as a second operating system (over my Windows Vista), and I'm having trouble with my wireless internet. I'm picking up signal for 7 other networks, but not mine. And I can't figure out how to make it search for more. If it's relevant I have a WPA2 Personal network set up, that is received on my PC when I run Vista and on my XP laptop (which I'm on now).
View 3 Replies View RelatedFor some reason, ubuntu cannot find local wireless networks. In fact, the Broadcom wireless card Ralink RT5390 802.11b/g/n seems to be incompatible with ubuntu. I've tried numerous 'solutions' on the Internet, but none of them seem to work on my computer. Tutorials I've visited have recommended downloading the b43 drivers from the Synaptic package manager and also the bcmwl-kernal-source package. Nevertheless, the wireless never turns on and Additional Drivers never shows anything at all. After several exasperating hours of trying to get my wireless running I've decided to turn to the forum for help. I'm sure there's probably more information I should supply, but I'm honestly not sure what that would be.
View 2 Replies View RelatedI have a device (not a pc) connected to my pc via ethernet, it dose not show up in networks, I was hoping there was a way of scanning to detect for it, is there a way of seeing content of it is basically what I'm asking?
View 5 Replies View Related
