OpenSUSE Wireless :: Broadcom 4328 Wifi Card Missing From System - Lspci
Mar 27, 2011
I recently installed suse 11.4 x64 onto my hp tx2000 tablet. everything has been working great including the wifi card. It's a broadcom 4328 a/b/g/n/bluetooth card and it was using the broadcom-wl driver. Earlier today i plugged in an usb wifi adapter to test whether it worked on suse plug and play. Well after plugging in and using this wireless adapter, my internal wifi card is no longer visible to the system. I've tried lspci and its not displayed. I booted into a different suse install and it wont work there. My bios does not seem to have a disable feature and the killswitch is in the correct position. The bluetooth is working but the wifi is not. In lspci i used to see "hp integrated (wireless+bluetooth)" and "broadcom 4328..." but now only the former.
I am succesfully installed a Dell wireless card with Broadcom 4328 shipset using ndiswrapper and rpm sources on Fedora 12 2.6.32.14-127.fc12.i686.PAE. Now I am using original Win drivers but the wifi conection is very slow and unstable.
I recently installed Suse 11.4 on my Dell Latitude 2110 netbook using the KDE live distribution, and, after that, the Broadcom wireless ceased to work. To enable the wireless connection, I have to press Fn + F6. If I do it now, the wireless led indicator turns on for a couple of seconds, then turns off again. Moreover, the option to enable the wireless connection in the network manager is greyed out
Code: wlan0 IEEE 802.11abgn ESSID:off/any Mode: Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit: 7 RTS thr: off Fragment thr:off Encryption key: off Power Management: off dmesg output:
Code: [8.330963] brcm80211: module is from the staging directory, the quality is unknown, you have been warned. [8.362403] brcm80211 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [8.362422] brcm80211 0000:0c:00.0: setting latency timer to 64 output of rpm -qa | grep broadcom:
Ubuntu 10.04 fresh install 64bit. Wireless was working in 9.10, now does not even show up in restricted drivers. Installed bcwl-kernel-source, and b43-fwcutter. ifconfig, iwconfig only show eth0 and lo - no wlan
Other restricted drivers show up - using NVIDIA driver with Compiz running better than ever on 2 screens
Here is the output from the collectNWData script found at [url]
I do notice that in the firmware section that both b43 and b43legacy are listed. Somewhere I reads that I should be using b43 - not the legacy version. Should it be blacklisted?
I just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
wifi card:atheros ar5007egOS: openSUSE11.4My laptop can't connect on network after system hibernate. It has been asking me for enter the wifi password. But when I input the wifi password it still can't connect on network. I have to reboot it.
I have installed Fedora 15 on a Mac mini 2.4. Everything works fine except the audio and wireless devices.
lspci shows this:
In the gnome, the network option only shows the wired connection. I tried to do yum install kmod-wl which downgraded the graphic display and didnt help in wireless issue. I reinstalled nvidia driver. the lspci is after doing all this stuff.
I've been reading up on how to get the Broadcom BCM4312 802.11b/g on my Dell Inspiron 1525 to work with OpenSUSE and I've tried everything, I've even re-installed the OS 3 times as I seemed to keep screwing something up. I've tried doing what it says in this thread Install Broadcom Drivers from Packman I thought I'd installed the write drivers with this code: Code: zypper in broadcom-wl broadcom-wl-kmp-default
I've installed new drivers and when I go to connect the MAC address shows up on the router but only for a few seconds and then disappears and I can't access wifi. I've even attempted opening up the router and still can't connect.
I am having a problem while connecting to a D-Link Access Point with Multiple ESSID. It keeps saying activating but in the end nothing. I am using KnetworkManager & there is no Encryption on the Access Point.I am able to get connected with another machine using windows.Here is my hardware info:
0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card [1028:000c] Kernel driver in use: b43-pci-bridge & the logs: Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.188245] wlan0: authenticate with f0:7d:68:17:e5:a4 (try 1) Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191262] wlan0: authenticated Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191501] wlan0: associate with f0:7d:68:17:e5:a4 (try 1) Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.194008] wlan0: RX AssocResp from f0:7d:68:17:e5:a4 (capab=0x421 status=0 aid=1)
when it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0
dell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
My laptop is supposed to have a 802.11 a/b/g/n wireless network card, but I can't find it. I've run lspci -nn without seeing anything containing. 802.11 in the output. Moreover, when I look into hardinfo->network->interfaces I only find the wired connection. Could anyone please tell me if these programs find all devices or if there could still be a wireless card here?
I have just completed the installation of 11.2 on a older HP Pavillon dv5115nr. Finally got everything working except for the Broadcom wireless. I have updated the firmware and I can see the AP. I have been using yast to configure the wlan device but one of the last steps it trys to perform is install smpppd. Even when hooked up via eth0 it can't find this program.
I'm sure you've seen this question before -- I tried searching but I can't find a clear answer. All I need is to get my wifi up and running in Ubuntu 10.04. I'm currently double-booted with XP on a Dell Latitude E5400 laptop. I'm in Windows right now. I can't post my lpsci readout because I can't access the internet from Ubuntu -- no access to wired connection.
I worked on this problem for a long time last night and fixed it somehow by installing a driver program -- it had "cutter" in the name. Today, however, I try to log in and Ubuntu won't connect to an open wifi point. Boot #1 it recognized it but wouldn't connect. Boot #2 it wouldn't recognize it at all (said "wireless is disabled" even though it wasn't. Boot #3 it would recognize the wifi point but wouldn't connect.) I can mantain a constant connection to this wifi in Windows XP and also on my Android phone.
I just want someone to please tell me how to get my wifi working reliably. I'm excited to switch over to Ubuntu, all I need is for the wifi to work. My wifi card is a Broadcom 43xx (4312?). Something like that.
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
I have an emachines D620 laptop running Ubuntu 10.10 with a Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01). I havent done anything with it and cant seem to get it to work. I know this because when I had visto on it the card worked, but know it says that its firmware is not enabled and ive tried installing the drivers using the Additional Drivers under Administration. I would like it to be working so I can use my laptop's internet.
I have just installed openSuse 11.4 and have been trying to get my Edimax EW-7711In wireless card to work. I have downloaded and installed NDISWRAPPER but when I type ndiswrapper -i /path/to/rt2860.inf I get a message saying that this is the incorrect driver. However this driver drives the card for both Fedora 14 and Ubuntu 10.10, both using ndiswrapper, so what may be the problem with openSuse 11.4?
i am using fedora 14 in my lenovo z560 laptop. It contains broadcom wifi card. The configuration is.Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g LP-PHY [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] I want to inject monitor mode in my laptop to run kismet . But i can't. I installed broadcom-wl driver in my laptop but i think its not compatible to run monitor mode.. when i run kismet it show me error that :------ try some other open source kernel driver And the other is :- kismet find only binary value eth1 port. It isn't detecting wlan0 port
From the title of this post, you can see that I am having some trouble getting the Linksys Wireless-G broadcom card working. I have been doing some research and have heard that getting a broadcom card to work in Linux can be a real pain.
I have verified that Mint 10 recognized PCMCIA so I am good there. I installed Wifi-Radar to see if maybe it would recognize it but it did not.
When I type iwconfig, it does not show any wireless signals available. When I originally set up the partitions for this laptop, I used PartedMagic and was able to quickly set up the network on that with vertually no problem what so ever.
I have a Laptop PC Acer Aspire 1710 and OpenSuse 11.2 installed on it I tried to setup my wifi card but it doesn't workI checked the log system log file.Apparently the driver cannot be loaded :
<6>[ 8.556483] b43-pci-bridge 0000:03:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 <6>[ 8.560204] ssb: Sonics Silicon Backplane found on PCI device 0000:03:03.0 <6>[ 8.581966] cfg80211: Calling CRDA to update world regulatory domain
i have an Acer aspire 4920 laptop with opensuse11.3 installed and wifi card has identified home wifi, but for some reason when i enter the wpa-psk key it doesnt connect.i have been at this problem for several days and scanning the net for answers, without joy.i dont know about the command or terminal line, i have tried to type in commands but i get no joy.
I installed Ubuntu 10.10 amd64 online today. I was using 10.04 32-bit before, and the network drivers were easy to find and install. Ubuntu did the job for me and they worked flawlessly. It was a relief I didn't need to search around.
Even though 10.10 (64bit) found the drivers for me, both ethernet and wireless, they do not seem to be working alright. I installed both, made a restart. I found that the WiFi light on my laptop stays on, even if the wireless network is turned off using either the key combination (Fn+F2), or manually turning it off.
Issues with the ethernet? I am right now using ethernet but it does not care to detect the connection. Empathy won't connect automatically as a result- says no network connection. But here I am, posting this. Evidently, there is a connection, right?
Issues with the wireless? The WiFi light stays on all the time, and it isn't able to get hang of the connection I have at home. It just won't show any wireless connections available. When I tried to connect by giving it the SSID and the encryption type and password, it didn't work. Just kept asking for the password again and again (I have checked with the router- the password is correct).
The funny thing is that it works fine in a Fedora installation, which has an older kernel and older drivers, on the same laptop. The fact that the indicator light doesn't come in when the physical switch is turned on suggests it's something to do with that switch.
I decided to start of with Debian. I'm having trouble getting my wireless connection to work. I think i need drivers or something, i can't make a wireless connection. And it is a bit difficult for me, as i am new to Linux, and I'm not sure what I'm doing when i am writing these commands.
My wireless card is a Broadcom Corporation BCM43142 802.11b/g/n
I have been using Raspberry PI a little, so i am familiar with the terminal.
