I bought this tv card because it was listed as working 'out-of-the-box'. Well, it didn't for me. I've googled and forummed for 3 days, tried all the fixes and nothing works.
View 1 RepliesI can not get my usb dvb-t sick working. It is a hauppauge WinTV-HVR 900 hybrid TV stick.
The number on the backside is: M/R: 65018/BC20 Some time ago I read somewhere that this model was supposed to work with ubuntu 9.10. [URL] it is possible to make it work since the poster appears to be using the same model as I do.But I still have trouble setting it up.
I just put Hauppauge WinTV-HVR2200 device to my system, however I can't get it working
Code:
$ lspci -s 03:00 -vvv
03:00.0 Multimedia controller: Philips Semiconductors Device 7164 (rev 81)
Subsystem: Hauppauge computer works Inc. Device 8900
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
[code]...
Upgraded system so I could store more recorded video. Now system identifies the Hauppauge WinTV PVR-150 card as a scanner. I have the original setup disk from Hauppauge but it is not Linux compatable. Running: Ubuntu 9.04 on: AMD Athlon64 X2 Dual Core Processor 5200+
View 11 Replies View RelatedI am having problems with Natty AMD64 (Ubuntu 11.04) and LIRC/IR-Keytables.
I have a Hauppauge WinTV card (Bt87 (TV card and IR receiver/transmitter) that worked (for the first time) automatically with 10.10 and LIRC. I recently moved over to 11.04, copied my LIRC config files over (hardware.conf, lircd.conf, lircmd.conf, etc), and received the error couldn't find any node at /sys/class/rc/rc*
The modules I had previously been successful with were: lirc_dev & lirc_i2c, as is apropriate for my speific card.
I then learned that Natty incorporated a lot of RC elements in to the kernel, and tried following:[url]
Which suggested removing lirc. At this point, ir-keytable also gives the same error about no node at /sys/class/rc/rc*
I think that I am having a problem with the correct driver being loaded for my card. When I look at a dmesg, the relevant section is: (note: I'm not sure if this dmesg was from before or after I uninstalled LIRC and just tried keytables)
Code:
The 3rd last line makes it seem that the IR capabilities have been recognized further confusing me as to why no /sys/class/rc/rc* has been registered. I've attached an unedited copy of my proc/bus/pci/devices, and below is my lsmod.
Code:
I am trying to install a Hauppauge 1850 video card into Linux Home automation system (LinuxMCE) which is based on Ubuntu Intrepid (I can't upgrade the kernel since this is what the LinuxMCE distribution supports)I am feeding analog signal to the video card, either through a coax analog connection or an RCA analog connection. I cannot see any picture from the card (I verified that the video card is working properly under a Windows Vista OS)I am trying to use the video card using a lightweight application such as tvtime, xawtv. In all applications I am failing to see an image. (For example, tvtime shows the message "No inputs avialble Cannot open capture device /dev/video0". Right clicking on Input configuration / Change video source doesn't give any options)
View 9 Replies View RelatedI've followed instructions here upto the point for the Startup Script for Analog Tuner the script provided does not run (v4l2-ctl seems to be depriciated?) In any case the scan for digital channels is not finding anything, I wasn't able to scan for analog channels. When I do something like cat dev/video0 | mplayer All I see is static. I've followed the instructions and I didn't get any obvious error messages. I'm completely lost. I know the tuner works, I've tested in in Windows 7. I've tried connecting the coaxial cable directly to the tuner's TV outlet, to the ATSC outlet, I've tried connecting the set-top box out coax to the TV, and ATSC outlets to no avail.
View 1 Replies View RelatedI've been trying to get my Hauppauge USB Live 2 video grabber to work under Ubuntu 10.04. I have installed the drivers, and using TVTime I get a perfect picture - but no sound, and also I can't record with it. I have found a guide on how to get it with sound using MythTV, but it seems I fail at setting it up. It tells me it couldn't find the backend server, but it's running in my terminal.
View 1 Replies View RelatedI have configured Kaffeine to work with my Hauppauge WinTV HVR 950Q USB device, and am able to get channels scanned, and can get sound, video from channels, etc. However, its use overheats my laptop to the degree it literally shuts down- turns off! Any suggestions? It took some effort to get this to work in Ubuntu 10.10; however, if it heats up the laptop to this degree what good is it?!
View 3 Replies View RelatedI have Ubuntu Karmic 9.10 with this card, its just works without any configuration but I have a big problem.
I start Kaffeine 1.0-svn3 and I can see the last dvb-T channel but when I want to change to other channel I can't see it, I have to restart Kaffeine, or wait to get the "Read error from:" error press Ok and select the channel.
How do I install WinTv pvr-250 (Tv-card) on my ubuntu 9.10 Karmic Koala? I am new to linux and not quite sure to begin. I would like to be able to use it to watch TV on my computer, using VLC, mythTV or similar.
View 3 Replies View RelatedI'm running 10.04 64-bit with all stable and pre-release upgrades enabled in a Dell 4-core Inspiron with 8 GB of memory. I just bought a Hauppage WinTV-HVR 1600 and it's detected in the boot process and all firmware is loaded, but then it goes bonkers and spews
[ 24.421795] cx18 0000:02:01.0: firmware: requesting v4l-cx23418-dig.fw
[ 24.612289] cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
[ 24.632510] cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
[code]....
over and over again. All the info on the Hauppage site and LinuxTV is very obsolete. MythTV initializes, but can't find any channels on either the analog or digital streams.
I'm just not getting anywhere here after 12 - 15 hours of googling last 3 days.I'm linked out, and linked back, almost into a do-loop, just like a boomerang, and still no vids...
View 2 Replies View RelatedI tried mythtv and I can't seem to figure it out. The only guides I can seem to find are for 6.06.
View 1 Replies View Relatedwhat can I use to watch TV? Obviously in Windows I used Windows Media Center. What can I use while in linux? I want to run Ubuntu, not Mythbuntu.
View 1 Replies View RelatedAfter some difficulties I succeeded to run this TV card under SUSE 11.1 with kaffeine 0.8.8.Everything works fine except for that the card refuses to tune on a DVB-S2 transponder. (For Example TP 11 on Astra 19.2E)The terminal output looks like this:
Tuning to: Das Erste HD / autocount: 1
Using DVB device 0:0 "Conexant CX24116/CX24118"
tuning DVB-S to 11362000 h 22000000
[code]....
I've got a strange problem with my Hauppauge card; I've just undertaken a clean install of Mythbuntu 10.04, and the built in Hauppauge remote for my Nova S2 HD card is intercepting remote signals from the number and direction keys and sending them as keypresses to the terminal - even when lirc isn't running.I didn't have this issue under 9.04 - but it seems that whatever is intercepting the IR signal is preventing LIRC from getting a look-in as it makes no difference whether lirc is running or not.I found this thread: URL... but the link to the explanation is dead and my attempts to blacklist lirc_i2c and gpio_keys have made no difference.
View 4 Replies View RelatedThis is a writeup to help you enable your Hauppauge 1250 tv tuner card so you can use it with programs such as Mythtv. This will enable multiple cards. I am assuming your card isn't working "out of the box". You can check if it is recognized in the OS by following the instructions in "How to tell if the TV card is recognized" below.
In linux land, the 1250 is not just a 1250 but can be a variety of designations. I own older 1250's which are listed as 1270's. My newer cards are listed as 1255's. These cards usually don't work "out of the box" with linux. You have learn the ropes and enable them yourself. You have to have time on your hands and be a glutton for punishment when it comes to setting up linux but a stable, well running system is worth it. If you need everything done for you and want it "out of the box", you might as well ride back to Bill Gates' Boneless Chicken Ranch.
First off, here is an updated cardlist for the cx23885 driver that is used with the 1250 amongst other tuner cards:
[Code]...
I've looked everywhere for this and I can't find an answer. I've got a hauppauge wintv-1250 card; ubuntu and mythtv recognize it OOTB. The dvb digital tuner portion of this card works great. I had quite a time figuring out how to set it up, but it all works pretty good now. nyway, the only problem is that I need to record 2 sources: 1 is RF, the other is from an analog cable box. So, I figured I should be able to record analog video from the s-video input. Is this possible with mythtv, and if so, how? I could watch it in windows with the software that came with the card, so I know it's possible, but I'd rather avoid windows if I can.
View 1 Replies View RelatedI've been doing alot of reading but i cant seem to get my HVR-1250 card working with mythTV, my system see's it but i cant get myth TV to recognize it? it doesnt come up in the "probed info" in the backend, do i have to just plug in the right info and not worry about that or what?
sudo lshw -C multimedia output:
Code:
*-multimedia
description: Multimedia video controller
product: Hauppauge Inc. HDPVR-1250 model 1196
vendor: Conexant Systems, Inc.
physical id: 0
bus info: pci@0000:02:00.0
version: 04
width: 64 bits
clock: 33MHz
capabilities: pciexpress pm vpd msi bus_master cap_list
configuration: driver=cx23885 latency=0
resources: irq:17 memory:fe800000-fe9fffff
ubuntu 10.04 32 bit
AMD Atholon dual core
I recently upgraded my old Hauppauge TV Card (BT878) with a HVR-1300. Whilst the older card worked OK, I am struggling to get the new card to work, despite it seemingly having installed OK in YaST.
View 2 Replies View RelatedI have a physical storage problem and want to put my VHS tapes onto disk. I have an unused Hauppauge WinTV-PVR350 which I understand should do the job but can I do it using Linux? I seek some pointers on what program to use, how to do it and tag the resulting files and help installing my Hauppauge card and any driver if required. I have openSUSE 11.4 (64bit) installed using KDE desktop.
View 7 Replies View RelatedI run Ubuntu Karmic (9.10) and have a hp psc 1110 connected by usb. The printer works fine (with hplip and cups). And sane-find-scanner answers:
Quote:
found USB scanner (vendor=0x03f0, product=0x3011) at libusb:005:004
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
However, scanimage -L reports "No scanners were identified. The strange thing is that the scanner used to function (with xsane as front-end) a few weeks ago. Somehow I broke this functionality, possibly when I installed drivers from HP to get better options for the printer part (e.g., switch color cartridges off). Any idea where I need to look to get it running again?
Alright I am about to throw this western digital device out the door and drive over it. The back story is that I have done a Debian net install on an older tower PC laying around the office. I am going to use this tower as an FTP server to store and backup several other servers we have have. We also have an older Western Digital (WD) my book 1110 sitting here. I was planning on using the external storage as the repository as it is 1TB raided. Seems like a good plan, plug the device into the tower and instantly two new drives show up "External CD-ROM" drive: "WD Smartware" and then "My Book". When I click on the cd rom drive I get the .pdfs and executables that are stored on the device. However when I click on the "My Book" drive I get the message "Invalid mount option when attempting to mount the volume 'My Book'.".
View 7 Replies View RelatedI performed an install using the 5.0.6 amd64 netinst cd on a dual opteron server with an Areca ARC-1110 4-port SATA hardware RAID card. I have 2 250GB drives set up as RAID 1. The debian install saw it as only one drive, just as it should. Install went smoothly, but on reboot, the system would not load.
I did some research and tried a couple of things with no luck. Like adding a delay in the grub command. It jus sits at loading system for a while then times out and loads busy box. Just to check things out, I booted into an Ubuntu live-cd and mounted the volume. The file system is there and all of the necessary files. How to use one of these cards successfully?
I bought this tv tuner. I cannot get it to work however. here is my dmesg log [URL] I have read this post at TV linux and it says that it should work out the box with karmic, my kernel is 2.6.31-17-generic I scanned channels using this command tvtime-scanner and it found some channels here is the output it shows channels picking up
Code:
xbmc@xbmc-desktop:~$ tvtime-scanner
Reading configuration from /etc/tvtime/tvtime.xml
Reading configuration from /home/xbmc/.tvtime/tvtime.xml
Scanning using TV standard NTSC.
Scanning from 44.00 MHz to 958.00 MHz.
Found a channel at 176.50 MHz (176.25 - 176.50 MHz), adding to channel list.
Found a channel at 184.00 MHz (183.75 - 184.00 MHz), adding to channel list.
[Code]...
how do I configure tv time to work? it just comes up with a no signal [URL] after I get this working I want to get the tvheadend working from this XBMC thread I dont know what to do as I am new to this and thought this would work out the box.
i want to try to get my wintv pvr usb2 running will this article still work to get it going? Set up Hauppauge WinTV-PVR USB2 - openSUSE is there a easier way?
View 9 Replies View Relatedi have a hauppage wintv usb2 tv device, works with windows OS, i want to watch live tv using this.
View 2 Replies View RelatedI have an HD-PVR that I'd like to use to strictly grab programs off my DirecTV HR24 - football/hoops, concerts, etc. The only machine I have that runs windows is my dual-boot laptop (Vista/Ubuntu 10.04). I'm currently using that and a windows program called Arcsoft TME. However, I'd like to be able to do this with my Ubuntu desktop PC which would be permanently connected to the HR24.
Since (stable) Linux drivers don't seem to be currently available to capture from the 1212, is it worth installing WINE and running TME under that? My goal is to make DVDs and delete the programs from the HR22.
I just got a Hauppague HVR-2250 in the hopes of being able to watch and record tv on my computer. I followed this guide to install the drivers: [URL] It seems to have installed alright I cannot tell if it worked. I am not using MythTV, nor am I interested in MythTV. I just want a simple application to watch ATSC channels. Me-TV seems like an application that fits the bill. It says there are no digital tuners detected though. I don't know if the drivers did not install or if the card isn't supported by the application.
View 3 Replies View Related