I'm looking for a low cost mono laser printer that just works under Ubuntu. I know that a general 'rule of thumb' is go with HP, but that doesn't seem to be the case with their low-end mono printers, as they use the XQX Stream Protocol instead of Postscript. The more expensive HP printers appear to work because they use Postscript.
View 3 RepliesI notice sometimes if the page has graphics it either is very slow to print or wont print.Will adding memory help? I was thinking of a 64mb module.
View 5 Replies View RelatedI would like to know how to network a HP P1005 Laser Printer that is connect to my desktop with Windows XP SP3 Home, & as well network files & folders to watch it on Ubuntu on my laptop?
View 4 Replies View RelatedI am using Lucid 10.04 and don't plan to change until support is dropped. I am looking to buy a multifunction monochromatic laser printer.
I was considering Samsung SCX-4828FN or HP LaserJet M1522NF. Both have network cards and support for Linux, but I am a little leery of the Samsung's support in Lucid. Does anyone have this printer? It seems to me a better choice if it works, because the toner is quite a bit more economical and I print quite a a lot.
My only requirements are all-in-one scanner/printer, economical, network card, proven to work.
Using ubuntu 10.04 a dell 1320 colour laser printer. I have been using a xerox driver for this but it will only printer from the single sheet feeder and no the paper tray. It works fine with XP and windows driver. I know that there is not a dedicated driver for linux but is there one which will work correctly and how do I install it?
View 1 Replies View RelatedI am using slackware 13 and cups is working OK. i installed the printer HP laser jet 1018 USB printer through localhost:631. it seems installed correctly but when i send test print there is no output.2nd thing i want to share that printer to some other windows machine on network so they can also use that printer
View 2 Replies View RelatedLaserJet Pro CP1525NW. HP website mentions that it is compatible with Linux. However, this particular model cannot be found at Linux Foundation's OpenPrinting Database. As you can see here, there is no mention of HP LaserJet Pro CP1525N which makes me worried. Also, the printer is not listed in HP Linux imaging and printing.
What are your thoughts and do you have experience with this printer? What other Color Laser printer do you recommend? The fact that the that printer's specification on HP website says that it is compatible with Linux, yet it is not listed on HPLIP nor in Openprinting makes me nervious.
Just purchased new del 1320cn printer and unfortunatly ubuntu doesn't see it. I tried the Foomatic system as well, which does see the printer and identifies it but does not show the model number in the list.
Any help would be really good. My other Del 1110 mono laser worked first time!
If any terminal commands reqd, please could you be kind enough to list them as I get confused using terminal.
distro: ubuntu 9.10
Printer: Del 1320cn Colour Laser Printer
I am having a Canon 3108B printer But no driver/rpms for my fedora 9. I can going to install fedora 12. Can i download driver for this printer also? if so from Where?
View 1 Replies View Relatedi am getting problems in order to install my HP laser jet p1006 printer for FC14.
View 15 Replies View RelatedCan anyone recommend a reliable network laser printer for a small office (it will be used quite often)Actually, it doesn't have to be laser - what's more efficient?Obviously it has to work well with linux.
View 2 Replies View RelatedI have Fedora 11 and am trying to install Brother HL-2170W Wireless laser printer. I installed it and used CPUS but cannot print. SELinux is enabled. On Brothers site there is an FAQ about SELinux and CUPS. [URL] I followed these instructions but still cannot print. Jobs get queued. Under Printer properties -> Policies, there is an Enabled checked. For some reason when I check this Enabled box and click Apply, the changes do not take effect. Then Enabled checkbox gets uncheck again.
I cannot even print a test page as its status shows Pending.
Has anyone installed successfully a Canon LBP3000 laser printer?I would like to make it work under F14 and F15.
View 5 Replies View RelatedI have a recently purchased Brother HL-3040CN printer that I had been using under Windows XP. I'm hoping to use it on openSUSE 11.2 64-bit. Having consulted SDB:Installing a Printer - openSUSE I ran lpinfo -l -m | grep HL-3040CN as su... evidently this model is not supported.The Brother site Brother Solutions Center : Brother Driver for Linux Distributions seems to suggest maybe there is hope. I am relatively new to Linux.
View 3 Replies View RelatedI have been printing with this laser printer (connected via LAN) for months without a single glitch, when suddenly today I had to quickly print a document. I could not print it. At first I thought the printer was off, then I double checked it was on. I restarted the CUPS server, reinstalled the printer in CUPS, nothing will work. When I send a print job, (I am using XFCE btw), I see the printer icon in the tasktray and it has a small warning sign.
Opening the print queue, I see "Processing - Printer Warning". In cups, I see nothing unusual. It says (in the printer queue): processing since Sat 25 Jun 2011 10:13:30 AM EDT. I can print a test page FROM the Printer web interface, confirming the printer works. I can print with the other printers. CUPS detects the printer and does not report anything unusual. What is going on with CUPS?
Hp P3005 Laser printer gives 49FF04 error message and 50.2 fuser unit problems. I open my printer, It doesn't receive tray paper. If you give this issue information about my broken piece, on fuser film is torn inside,deformed lower sleeved roller Worn bushing. I will buy a company this spare part on I want to fix my own printer.(Please understand my english is not very good show ) Bilberk Printer-Service-Spare parts [Moderator edited to remove advertising link.]
View 1 Replies View RelatedI have tried to mount an HP laser printer on my home network through a VPN IPSES connection from my laptop, but I cannot manage to see the printer or make it accept commands.
View 1 Replies View RelatedI have bought a BrotherHL-1110 laser printer. But there is no driver on my system. I have downloaded source code but don't understand how to compile it. (
It does only exist driver-packages for 32 bits: hl1110cupswrapper-3.0.1-1.i386.deb and hl1110lpr-3.0.1-1.i386.deb)
My system is:
Release 7.8 (wheezy) 64-bit
Kernel Linux 3.2.0-4-amd64
GNOME 3.4.2
AMD Athlon(tm) II X2 245 Processor × 2
The source code contain the following files:
-> pwd
/home/joe/Desktop/BrotherHL-1110/hl1110cupswrapper-GPL_src-3.0.1-1
-> ls -R
.:
brcupsconfig Copying filter PPD
[Code] ....
How do I compile and install it on my computer ? ( Or get the printer working ? )
i have custom programs written in Basis pro5. Standard output to a pdf virtual printer works fine. Using pdftk to overlay on to a form is hit or miss.... There are products out there like Unform that are just too expensive for my company. i have purchased another product from a company that prints the forms to the laser perfectly but i am incapable of capturing them and saving them as pdf's for archiving/emailing/faxing and i don't much care for this company.
View 2 Replies View RelatedI have recently installed linux 'uberstudent'and find it doesnt recognise my floppy drive but more importantly I cant install my printer a samsung ML4500 laser. There are readme files (reproduced below) but I just dont know enough about the system to know what to do with them " does it mean anything to anyone ? I am a bit reluctant to experiment with terminal incase I mess up the entire system ! also could their be a connection between this and the floppy not working ?
1.AUTORUN will not run
2.clicking cdsetup.exe and selecting 'open with archive manager' results in : 'an error occured while loading the archive'
3.clicking cdsetup.exe and selecting 'open with wine windows programe loader' results in 'samsung printer setup window'etc, and it appears to load normally until 'PROGRAM ERROR 'DAC1.EXE encountered problems and has to be closed.
4. Inside the linux folder are three file's, copied and shown below
The first file is entitled :
I am on Ubuntu 10.10 on Thinkpad T61p
Recently installed my office printer with the drivers provided by them(office people)
The problem is that it works fine but only with few selected applications
Adobe Reader works fine Foxit reader fails Document viewer and image viewer prints the page but doesn't fit them inside the margins and they are either cut on the edges or look ugly
Printing from browsers doesn't work either. I always have to do 'print to file' in pdf format
Then pray rigorously that the pdf print is nice and then print using Adobe reader
where to start debugging from ?
Have recently updated 10.04 with latest updates which included a new kernel and the printer no longer works. In-fact I can't even define the printer and I don't have a printer installed, the install script can't locate the printer on the USB. I have a cannon MP640.
I can print OK through windowsXP on virtualbox, printer is found OK.
Everything was fine until latest update.
Also my USB TV card doesn't work anymore, it also was OK before the update.
anybody out there with an idea for a command to make the WLAN-Printer (HP-Officejet)work again when it stops after 30 Min - 2 h.Simple stopping the print job and print again does not help. The only way for me is to stop the print job and RESTART. Then it works again 30 Min- 2 h. I use updatet lucid lynx 32.
And I need a command like "killall pulseaudio" that I need when I return from logged-on as the second user to get sound again.
I am looking for a HP Multifunction Printer that works well out of the box with Linux. I have been to the printer tables and seen the host of HP printers that work, but I would like to hear from someone who has recent experience.
View 2 Replies View RelatedThis may sound dumb but if I upgrade from 8.10 to 9.04 will I lose all of my emails addresses, bookmarks, etc?
View 1 Replies View RelatedTonight I bought an HP LaserJet 1020 on Craigslist. Installed it and printed a test page without any trouble. But when I try printing a multi-page document, it only prints the first page, and then I get a message saying it may be disconnected. It's not, but I waited a loooooong time and the successive pages didn't spit out.
View 9 Replies View RelatedI have Linux Xandros Debian software on my Asus Eee PC, and for 3 years now I have been trying to buy a Colour Scanner that works. It does not have to be a stand alone Scanner, it can also be an All-in-One. I have been told the HP has the most chance. However I bought a HP Deskjet F2280, that the salesman guaranteed would scan with Linux, but it did not. And never has. Is there anybody who also has Linux Xandros Debian and HAS found a scanner that works?
View 1 Replies View RelatedSome context: I'm calling some functions from within a C program and want to measure how long they take to execute. I've done this successfully, calling printf to print the results to the screen. This is reasonably fast. Ideally I'd like these to be dumped to a file, but fprintf presumably has some overhead since it writes to disk? Unless the data is buffered by the kernel and flushed later? What kind of delay can I expect before fprintf returns?
If I redirect the stdout to a file when I instantiate the binary as a process, will calls to printf also experience any overhead from redirection to a file? My aim here is to capture all data in a file, with the minimal amount of coding and effort, but with minimal impact in terms of time overheads for printf calls.
Fedora15 32bit. I write a test program, it creates new thread continually, the thread does nothing but sleep. I find virtual memory increases up almost 10Mb when a new thread is created. and when there's more than 200 threads, the virtual memory used by the program is 3Gb, and now cann't create new thread. but on windows, it costs little memory. What can I do to config the operation system to take less memory on threads?
View 11 Replies View Relatedi have a hp 6500 e709a printer. have configured for network printing and would like to use the scan facility.i have tried to scan from the printer but it does not find the computer. the hp documents mention advanced firewall information on incoming udp ports and tcp ports etci believe it is with my machine as my son has a windows box with the hp software and i have managed to scan from that machine.
View 4 Replies View Related