I would like to know how to network a HP P1005 Laser Printer that is connect to my desktop with Windows XP SP3 Home, & as well network files & folders to watch it on Ubuntu on my laptop?
View 4 RepliesCan anyone recommend a reliable network laser printer for a small office (it will be used quite often)Actually, it doesn't have to be laser - what's more efficient?Obviously it has to work well with linux.
View 2 Replies View RelatedI have tried to mount an HP laser printer on my home network through a VPN IPSES connection from my laptop, but I cannot manage to see the printer or make it accept commands.
View 1 Replies View RelatedI notice sometimes if the page has graphics it either is very slow to print or wont print.Will adding memory help? I was thinking of a 64mb module.
View 5 Replies View RelatedI'm looking for a low cost mono laser printer that just works under Ubuntu. I know that a general 'rule of thumb' is go with HP, but that doesn't seem to be the case with their low-end mono printers, as they use the XQX Stream Protocol instead of Postscript. The more expensive HP printers appear to work because they use Postscript.
View 3 Replies View RelatedI am using Lucid 10.04 and don't plan to change until support is dropped. I am looking to buy a multifunction monochromatic laser printer.
I was considering Samsung SCX-4828FN or HP LaserJet M1522NF. Both have network cards and support for Linux, but I am a little leery of the Samsung's support in Lucid. Does anyone have this printer? It seems to me a better choice if it works, because the toner is quite a bit more economical and I print quite a a lot.
My only requirements are all-in-one scanner/printer, economical, network card, proven to work.
Using ubuntu 10.04 a dell 1320 colour laser printer. I have been using a xerox driver for this but it will only printer from the single sheet feeder and no the paper tray. It works fine with XP and windows driver. I know that there is not a dedicated driver for linux but is there one which will work correctly and how do I install it?
View 1 Replies View RelatedI am using slackware 13 and cups is working OK. i installed the printer HP laser jet 1018 USB printer through localhost:631. it seems installed correctly but when i send test print there is no output.2nd thing i want to share that printer to some other windows machine on network so they can also use that printer
View 2 Replies View RelatedLaserJet Pro CP1525NW. HP website mentions that it is compatible with Linux. However, this particular model cannot be found at Linux Foundation's OpenPrinting Database. As you can see here, there is no mention of HP LaserJet Pro CP1525N which makes me worried. Also, the printer is not listed in HP Linux imaging and printing.
What are your thoughts and do you have experience with this printer? What other Color Laser printer do you recommend? The fact that the that printer's specification on HP website says that it is compatible with Linux, yet it is not listed on HPLIP nor in Openprinting makes me nervious.
Just purchased new del 1320cn printer and unfortunatly ubuntu doesn't see it. I tried the Foomatic system as well, which does see the printer and identifies it but does not show the model number in the list.
Any help would be really good. My other Del 1110 mono laser worked first time!
If any terminal commands reqd, please could you be kind enough to list them as I get confused using terminal.
distro: ubuntu 9.10
Printer: Del 1320cn Colour Laser Printer
I am having a Canon 3108B printer But no driver/rpms for my fedora 9. I can going to install fedora 12. Can i download driver for this printer also? if so from Where?
View 1 Replies View Relatedi am getting problems in order to install my HP laser jet p1006 printer for FC14.
View 15 Replies View RelatedI have Fedora 11 and am trying to install Brother HL-2170W Wireless laser printer. I installed it and used CPUS but cannot print. SELinux is enabled. On Brothers site there is an FAQ about SELinux and CUPS. [URL] I followed these instructions but still cannot print. Jobs get queued. Under Printer properties -> Policies, there is an Enabled checked. For some reason when I check this Enabled box and click Apply, the changes do not take effect. Then Enabled checkbox gets uncheck again.
I cannot even print a test page as its status shows Pending.
Has anyone installed successfully a Canon LBP3000 laser printer?I would like to make it work under F14 and F15.
View 5 Replies View RelatedI have a recently purchased Brother HL-3040CN printer that I had been using under Windows XP. I'm hoping to use it on openSUSE 11.2 64-bit. Having consulted SDB:Installing a Printer - openSUSE I ran lpinfo -l -m | grep HL-3040CN as su... evidently this model is not supported.The Brother site Brother Solutions Center : Brother Driver for Linux Distributions seems to suggest maybe there is hope. I am relatively new to Linux.
View 3 Replies View RelatedI have been printing with this laser printer (connected via LAN) for months without a single glitch, when suddenly today I had to quickly print a document. I could not print it. At first I thought the printer was off, then I double checked it was on. I restarted the CUPS server, reinstalled the printer in CUPS, nothing will work. When I send a print job, (I am using XFCE btw), I see the printer icon in the tasktray and it has a small warning sign.
Opening the print queue, I see "Processing - Printer Warning". In cups, I see nothing unusual. It says (in the printer queue): processing since Sat 25 Jun 2011 10:13:30 AM EDT. I can print a test page FROM the Printer web interface, confirming the printer works. I can print with the other printers. CUPS detects the printer and does not report anything unusual. What is going on with CUPS?
Hp P3005 Laser printer gives 49FF04 error message and 50.2 fuser unit problems. I open my printer, It doesn't receive tray paper. If you give this issue information about my broken piece, on fuser film is torn inside,deformed lower sleeved roller Worn bushing. I will buy a company this spare part on I want to fix my own printer.(Please understand my english is not very good show ) Bilberk Printer-Service-Spare parts [Moderator edited to remove advertising link.]
View 1 Replies View RelatedI have bought a BrotherHL-1110 laser printer. But there is no driver on my system. I have downloaded source code but don't understand how to compile it. (
It does only exist driver-packages for 32 bits: hl1110cupswrapper-3.0.1-1.i386.deb and hl1110lpr-3.0.1-1.i386.deb)
My system is:
Release 7.8 (wheezy) 64-bit
Kernel Linux 3.2.0-4-amd64
GNOME 3.4.2
AMD Athlon(tm) II X2 245 Processor × 2
The source code contain the following files:
-> pwd
/home/joe/Desktop/BrotherHL-1110/hl1110cupswrapper-GPL_src-3.0.1-1
-> ls -R
.:
brcupsconfig Copying filter PPD
[Code] ....
How do I compile and install it on my computer ? ( Or get the printer working ? )
i have custom programs written in Basis pro5. Standard output to a pdf virtual printer works fine. Using pdftk to overlay on to a form is hit or miss.... There are products out there like Unform that are just too expensive for my company. i have purchased another product from a company that prints the forms to the laser perfectly but i am incapable of capturing them and saving them as pdf's for archiving/emailing/faxing and i don't much care for this company.
View 2 Replies View RelatedI have recently installed linux 'uberstudent'and find it doesnt recognise my floppy drive but more importantly I cant install my printer a samsung ML4500 laser. There are readme files (reproduced below) but I just dont know enough about the system to know what to do with them " does it mean anything to anyone ? I am a bit reluctant to experiment with terminal incase I mess up the entire system ! also could their be a connection between this and the floppy not working ?
1.AUTORUN will not run
2.clicking cdsetup.exe and selecting 'open with archive manager' results in : 'an error occured while loading the archive'
3.clicking cdsetup.exe and selecting 'open with wine windows programe loader' results in 'samsung printer setup window'etc, and it appears to load normally until 'PROGRAM ERROR 'DAC1.EXE encountered problems and has to be closed.
4. Inside the linux folder are three file's, copied and shown below
The first file is entitled :
I just upgrade to Fedora 11.
I have problem in installing the printer, no matter add printer in local network or Windows Printer via Samba.
The summary is as follow:
I have download a printer driver and had installed but got error when I tried to printer a test page.
I'm trying to add my Samsung SCX4500W printer to my opensuse 11.2 machine running KDE.From Yast->Printer->Add printerI am able to set the printer up, however there is no driver for my specific network printer. Samsung does provide a linux driver but I have no idea what I'm doing when installing peripherals on linux basically
View 3 Replies View RelatedHaving made the transition from a certain widely used operating system to linux, suse 11.2, x64, successfully and pleasantly we are still left with a few problems.One of these is a few applications i have to use which run only in that old OS. ?To that end I have installed VirtualBox and got them to run with one glitch. I cannot print from VBox to my HP LaserJet 4000, lpt1 printer, which works fine in suse. Searching and posting on the Vbox forums turned up that lpt1 is not supported in the current vbox and that I need to set up a virtual network, set up the printer as a network printer and set it up as an lpd/lpr printer in Vbox WinXP. Have tried many different ways to do this without success, I think the problem is I do not know how to set up a network printer in Linux.
The virtual network is vboxnet0, which does show up in ifconfig, along with my eth0 net, and I can ping the windows guest, gateway and the host from either side host:suse/guest:winXP) respectively. Have tried numerous ways of setting up printer in YaST which works in suse but still does not work from WinXP guest. Have read the suse manual and several sources and searched forums with no results.Finally I am thinking I just don't know how to set up a network printer in linux. Using cups, kde, suse 11.2, don't know what else to tell. Samba is installed, although I am not using it to the best of my knowledge.
I am trying to set uamsung clx2160N as a standalone network printer on my home network. It is a printer with standalone network capability and is connected directly to my router and has a static IP number. We have a few Windows computers at home and they had no problem detecting the printer, installing the drivers and working. Unfortunately my Ubuntu computer recognises the printer and I can even access it's setup and diagnositcs through its IP number. However when I try to add it as a printer, drivers for it cannot be located. #ve tried setting it up three ways:1. Using Samsung's own setup package - finds printer and all the details it needs to work but offers no drivers2. Using Ubuntu's printer setup - recognises printer but stalls at Searching for Drivers dialog3. Trying to *** printer using CUPS - no problem finding and recognising printer, but when I come to search for the driver I get Internal Server Error.
I have of course been trying to do all of these as root. That's the limit of my knowledge reached and searches on the net aren't helping me either. The printer works fine directly connected via USB, so the drivers are on the computer somewhere. How do I get them set up to use the printer on the network?
I have four PCs in my house that are running opensuse 11.2 and I want to create a home network to share files, scanner and printer.
View 4 Replies View Relatedis it possible to install a netwerk printer, while not connected to the netwerk where the printer is?I installed opensuse on my sisters desktop and I want to install the printer that she and my parents are using at home. Is this possible?De printer is in a windows workgroup and shared. De name of the workgroup is DEROON and the name f the computer the printer is connected to is Nico
View 4 Replies View RelatedTotal Newb here, sorry. I am pseudo-IT at work and have set up a desktop with Debian 5 (accidentally overwrote Windows in the process, but there you go). We are set up with network printers here (all Windows), and I was wondering how to go about being able to print to one of the network printers from my Linux desktop. Can I even connect to the Windows network with this desktop (it is hooked up)? Understand, I do NOT want to screw up anything on the network - they won't let me play anymore if I do. If I download the Linux driver, what do I do next?
View 2 Replies View Relatedi have 3 comps(running suse 11.3) and a laptop(running vista sp2). i have installed samba on all suse comps. i have a printer attached to one of the comps and it has been shared also the internet connection on that comp has been shared. all the computers are connected using lan cables through an ethernet switch. i also have a wireless router which is connected to the ethernet switch.
I am able to view all the comps on the network except the laptop running vista. all the desktops are visible on the network and are able to print and share files on the network and also connect to the internet. the laptop running vista can connect to the internet but its not visible on the network and nor can it share files across the network or access the printer.
I successfully added/shared a network printer in SUSE 11.3 32 bit, but when I try on the 64 Bit box it didn't work out very well.What ports need to be open ? Is it necessary to open port 631 in YAST->Firewall->Advance- >UDP and IPP ?(TCP 631 already open) What services need to be running? Here is the error log :
[16/Dec/2010:19:25:43 -0500] [cups-polld xxx.xxx.xxx.xxx:631] CUPS-Get-Printers failed: Forbidden
XXX is my server IP
I have two Suse un-firewalled computers connected via NFS. About a year ago I found instructions for a very SIMPLE way to share a CUPS connected printer using Yast. When I installed 11.4 I lost the instructions. It required no config file editing and took about two minutes. Google searches focus on complicated SMB-Linux connections like those suggested by swerdna.
View 6 Replies View Related