I installed ubuntu on my dual boot system which had XP and Windows 7 installed, and after installing ubuntu I was able to boot windows 7 and ubuntu, but unable to boot XP it says some dll file is missing, now I think if try to repair xp with installation disk it might ruin my ubuntu.
View 1 RepliesI have been running dual boot Windows XP and Slackware for years but I recently changed things up a bit a "broke" something.
Windows XP is on it's own 250GB HDD. I installed Windows 7 on a seperate 74GB HDD but it appears that it installed the bootloader over top of the Windows XP bootloader on the 250GB HDD. Both OS's booted fine and that point. Then I partitioned the 250GB HDD into 150GB and 100GB leaving me 100GB to install Ubuntu. I told Ubuntu to stick it's bootloader on the 250GB HDD thinking everything would work like magic although there appears to have been a little bit too much magic. Normally Slackware will allow you to manually edit your Lilo config file during installation and add all your OS's but this didn't happen with the Ubuntu install.
After the install there were 5 options in the bootloader menu (at this point I am not even sure what bootloader it was using). Ubuntu, Ubuntu ("safe mode?"), memtest, more memtest, and Windows 7 (bootloader? it wasn't just called windows 7 but something like Windows 7 bootloader, I have only booted once and I am writing this from Ubuntu right now). I tried selecting Windows 7 at that point hoping that it would bring me to the Windows bootloader which would allow me to select from Windows 7 and Windows XP but the screen just went blank for a second or two and then sent me back to the same screen I was just at.
So a quick Google of Ubuntu bootloader led me to believe I was using Grub and I needed to look for the /boot/grub/menu.lst file and edit that but the file wasn't there. Then I tried running grub but I was informed it wasn't even installed. I thought maybe I would have better luck with Lilo but that wasn't installed either. So I installed Lilo and ran liloconfig but I was told that fstab gave a UUID that led Lilo to belive I wasn't using an ordinary block device and I should go fix that and come back afterwards. In fact the only thing in fstab was the ext4 partition with Ubuntu and the swap partition even though I have 4 sata drives installed with 6 separate partitions.
At this point I am pretty lost. Most of my Linux work is done in Parallels now on a Macbook so I haven't had to mess with the bootloader in years and when I did it was all on Slackware which to me is set up quite a bit differently than Ubuntu. I would be pretty sick if I screwed up and took out 3 OS's with it.
How Grub will handle booting both Windows OS's when Windows appears to be doing it with one bootloader.
I pretty much know nothing at all about partitioning hard-drives and unspeakably less about linux as a whole. but i really want to get into it. (The HP Mini 311 is what i am using)
Okay so a couple of days ago (before i had ever heard of Ubuntu, or even thought i could ever use Linux based software). I had been Dual-Booting OSX Snow Leopard and Windows 7, while using Chameleon boot-loader, on my HP Mini 311. Even though my sound-card and network adapter do not work while running Snow Leopard.
I followed this guide for dualboot: [url]
So i heard about the new Linux Os Ubuntu, and after trying it for about 3min on a USB i was sold. So i began to make my HP a triple-boot now with OSX Snow Leo, Windows 7, and Ubuntu.
I did this by recreating the same dual-boot system as before, but this time saving room for Ubuntu to be installed to my hard drive, after SnowLeo and Win7.
I got this to work perfectly by creating a 4th partition for Ubuntu and a 5th for swap area.
Here is where my problem lies... I saw this tutorial for dual-booting Win7 and Ubuntu, while making another partition so that windows and ubuntu can share the same files.
Here:[url]
Once i tried doing this on my triple-boot(adding ubuntu partition, swap partition, and a "storage" partition, on top of the 3 partitions i created during dual-boot setup) My Windows 7 stopped booting. I read somewhere that hdds can only have like 3 primary partitions, which is the only kind of partition i know how to use. so i was thinking maybe i could put this storage partition in another mount location, such as /home or /usr, because i think the added partitions is what messed up my Windows 7 boot. My only problem is i have no idea what different mount positions are used for, nor how to use them properly.
I have a desire to boot Tripel windows7 arch and Slackware but unsure how to partison my hard drive??
View 5 Replies View RelatedI am trying to install ubuntu 10.04 on windows7.windows 7 was already installed.I ollowed these steps to install ubuntu 10.04.1)First i made some freespace in hard disk to install ubuntu using windows7 default options(By shrinking).2)I used USB drive to install ubuntu.I made it bootable using unetbootin.3)I followed normal steps install(language,area,keyboard,using manual partition i installed ubuntu in free space,etc).4)I got boot menu when it restarted.PROBLEM isAs long i use only ubuntu (boot into ubuntu --shutdown--boot into ubuntu --shutdown) it works well.
If once i boot into windows 7 and restart the system i am loosing boot menu options.The following error i am getting"no module name found Aborted.Press any key to exit".If i press any key,I guess its trying boot using internet and lastly it says Operating system not found and hangs.
I built this computer with a Gigabyte motherboard, i3 processor, 8Gb ram, 64Gb SSD, and 1.5Tb HDD. Loaded Windows 7 to the SSD... repartitioned the drives and loaded Ubuntu 11.04.The start menu comes up to select Windows 7 or Ubuntu... when I select Ubuntu I get a screen which reads:Windows failed to start. A recent hardware or software change might be the cause. To Fix the problem:1. Insert your windows installation disc and restart your computer.2. Choose your language settings, and the click "Next"3. Click "Repair your computer."if you do not have this disc, contact your sys admin or manufacturer for assistance. File: ubuntuwinbootwubildr.mbrStatus: 0xc0000098Info: The selected entry could not be loaded because the application is missing or corrupt.
This screen continues to come up. I tried to load Ubuntu with Wubi but it would not install... I have now installed it from a DVD but the load screen keeps putting me back to the screen above. I can't load from the Windows CD it won't recognize it even if I change the bios setting.Windows 7 seems to be running fine... and Ubuntu seems to have loaded fine... so how can I get my Windows boot screen to go and load Ubuntu as my OS?
I have done some commands in ubuntu 11.04 and got problems, thinking of reinstall it. (laptop acer 5738zg)
Previously when i have dual booted win7 and ubuntu10 and linux mint i always get "grub rescue" when i try reinstall my linux partition, and it ends with i have to do clean reinstall of both windows and linux, which is a major pain in the rectum area
Is there a way to make my linux go back to original state without reinstall, and if i reinstall, how can I do this without loosing win7 partition and get this awful grub rescue message.
I have a laptop that has a dual boot of Windows7/Ubuntu10.04. Ubuntu loads fine, but Windows 7 does not. It shows up in the Grub, but it will not load. I assume that the boot loader was messed up somehow, but I am not experienced at deciphering the boot info file. I was hoping someone might be able to take a look at the file and tell me what the issue might be, and also which part of the text indicates the problemBoot File:
Code:
Boot Info Script 0.60 from 17 May 2011
============================= Boot Info Summary: ===============================
[code]...
I have a Computer, It came with Windows 7 64bit on it. I installed Ubuntu through WUBI. I used the Windows Disk Management program to resize my HDD. I shrunk the main drive and created a 20 gig free space. I installed WindowsXP on this 20g space. I had to change from AHCI to ATA. I started my new XP installation. As I should have expected my the screen that let me pick between Windows 7 and Ubuntu was gone, and it just said XP. Well thats cool. I get in XP use bcdeasy and use the install Win7 to mbr. So I restarted. Great I now I have Ubuntu and Win7... but no XP. So i think, okay, ill boot into Ubuntu, use the update grub command and XP will be there, so i do it and restart. No XP, So i try to boot into Win7 and see if i can do something in there.. No luck it says it can't boot and takes me to a startup recovery thing. Which, as Windows recovery things tend to do, doesn't find anything wrong. So I have Ubuntu now, which is great, but I do need Windows.
View 4 Replies View RelatedI have a laptop that has multiple partitions and was running Windows 7. I installed Fedora in a area of free space in the extended area, thus in a logical partition. Fedora is now running on the laptop. But, at boot time, there is NO BOOT MANAGER. The laptop just boots straight away to Fedora.
I know this has probably been covered, but is there an "official" procedure or document available to us newbies that I can use to recover my system such that it boots all of my installed bootable partitions (including Windows7)?
Windows 7 is first boot disk. Installed Fedora 13 on second disk from DVD. During installation it did not ask if I wanted dual boot. Fedora installed fine on second disk. Rebooted and only Windows will lood. How to setup to dual boot? Can I modify Windows Boot file? or do I have to install Grub on to sda. How do I do that?
View 2 Replies View Relatediam new to linux i installed fedora 10 on windows7 ultimate 64bit after intallation the fedora system doesent boot, but windows7 work properly. i instlled fedora 10 in seperate fee partiotion
View 2 Replies View RelatedI have XP on sda1, Fedora 11 encrypted on sdb 1 (boot) and sdb 2 (root), I would like Ubuntu on sdc 1 (boot) sdc 2 (root). However when I tried to install from the cd the partition manager does not see my Fedora as an OS (I assume because it is encrypted). So my question is how can I achieve my triple boot without having to have my Fedora unencrypted. I want it encrypted for a reason.
Also I cancelled the installation for Ubuntu and it reverted to a Live cd and I tried to mount my Fedora encrypted drive. Ubuntu asked for the pass and when I entered it I get an error saying it cannot be mounted because it is not a mountable file system. This is not good for me because I would like to be able to access all my hdd's from both distro's.
For completeness here's the history that got me to this point:
Stage 1
/dev/sda - disk with XP OS, set to be first boot disk in BIOS
/dev/sdb - a small data disk to supplement sda
[code]....
I have (only bc i have to) windows vista, also Ubuntu 10.04 on the same drive, and dual-booting is no issue at all. But after I installed Mandriva 2010 to try to triple boot, i couldn't find Ubuntu anymore so I got rid of mandriva, and grub was messed up bc I deleted all mandriva partitions. So then I installed Xubuntu 9.10 (because it is a quick install) to recover grub, and with Xubuntu, Ubuntu, and vista, Grub sees all three OSes no problem. So what would I have to do to make Grub work this way when I install Mandriva?
View 5 Replies View RelatedI want to install a triple boot load consisting of Windows 7, Ubuntu 10.04, and Fedora.My question is, if I install Windows 7, followed by another distro, like Fedora, and then install Ubuntu 10.04, will the Ubuntu GRUB 2 menu display all three options?I know if I install Ubuntu and then install Fedora, I have to go through some heavy gyrations to get everything to show in the load menu, so it seems easier to install Ubuntu last.
View 2 Replies View RelatedI had Win7 installed on my Laptop and wanted to set up a triple boot with Fedora 12 and Mint 8.So I installed Fedora 12 and it worked loading grub and offering Win7 and Fedora as choices.Then I installed Mint hoping for the Grub2 to recognise Fedora and set up the triple boot but it didn't and I can now only boot into Win7 or Mint.sudo update-grub doesn't help.How can I configure grub2 to offer me all three OSs?
View 1 Replies View RelatedI recently installed ubuntu onto a pc running MS vista. Then I somehow managed to install a second instance of ubuntu. Both of these were on the (drive e Then because of HDD problems, I had to reformat my original drive with MS Vista (drive C). Because of installation problems with ms vista - I ended up installing it onto the drive e: also. But now I can no longer load ubuntu because the "GRUB" loader is missing. So my questions are:
1: How can I restore the "GRUB" loader? So I can access ubuntu again
2: How can I remove/uninstall the second ubuntu installation?
3: Is it possible to have a triple boot system with ms vista / ubuntu 32-bit / ubuntu 64-bit?
I have a Core 2 Duo iMac that I had set up for triple boot using Fedora Core (probably FC8 )and GRUB, Windows XP Pro, and Mac OS X v10.5. Some time ago, I had to blow out and reinstall my Windows installation because it had developed errors, but this also blew out my GRUB, leaving the Fedora install non-bootable. Since I never really used FC on this machine much, I didn't worry.
Lately, I've acquired an hp Mini 110, on which I'm running Linux Mint 8 (Helena), and I'd like to upgrade my FC partition on the iMac to Karmic, but when I run the installer, it won't let me use all of the existing Linux partition, instead wanting to resize it to accommodate both FC and Ubuntu.
How do I make the installer simply replace FC with Karmic, using the entire existing partition? I'm sure earlier versions of Linux that I've used had a simple "erase all Linux partitions and install" option, and the "Manual" option doesn't appear to read the existing partition information (I was too afraid to go any further).
I ended up quitting the installer, which put me into the Live CD environment, where I used the File Browser to "Format..." the Linux partition, but when I went back to the installer, I ran into the same problem, and it didn't seem to matter if I unmounted the existing partitions or not.
I i'm having trouble setting up my triple boot machine. I have Windows 7 and Mac OSX on two seperatate hard disks and they are dual booting fine with the chameleon bootloader. I just attempted to install ubuntu from liveCD which i downloaded and burned from the ubuntu website. During intallation i the option to "install side by side to windows" and resized the windows partition to make room for Ubuntu(250GB of 1TB), i also selected the option to disable the GRUB bootloader because i want to use chameleon. The installer completed successfully and the computer rebooted but chameleon, Mac OSX or windows (my partition for windows is 250GB smaller) won't recognize the partition.
View 2 Replies View RelatedI just upgraded to lucid lynx from karmic koala 64 bit. During the upgrade it complained about grub not working. It said if i didnt know what drive to mount i had to select all of them, which i did. Did i now damage my triple boot ? i had also win7/ winxp on my hd, but altho it says windows 7 in the grub menu if i select it nothing happens just a cursor blinking. I can get into Ubuntu okay. I looked at the forum here and saw someone being advised to get Bootinfo script.
[Code].....
I have been searching in preparation to install 10.04.1 with 2 installations of Windows,already installed.(Win 7 then Vista) I have left room at the end of the drive for Ubuntu. When I get to the stage to select the boot options and click on advanced, what should I select?
View 4 Replies View RelatedI have an MSI U100 netbook triple booting between Win XP, Ubuntu 9.04 and OSX. Grub is used as boot loader. I want to upgrade my ubuntu install but I am a bit scared that grub will be messed up.
View 1 Replies View RelatedI would like to triple boot vista, opensuse and ubuntu.
I need to set aside 165 gb for Vista (which has been backed up to an external drive).
Would like to make a fresh install of Ububtu and Opensuse with Ubunto being the main OS. I figured 100 GB for Ubuntu and 55 GB for Opensuse would probably be fine (the remainder I need to set aside for Vista).
Ive popped in the Ubuntu DVD and am about to install it but am stuck on the "allocate drive space" part. I do not understand how to partition the hd and what to set each partition to in the "Use as" and "Mount Point"
I am attempting to triple boot Ubuntu, Windows 7, and Backtrack 4. Win7 and Ubuntu are both booting and working properly, but after trying a number of configurations for GRUB I cannot boot Backtrack. Everything I attempt seems to come back to one problem and result in the same error: Error 17.
sda contains both my Windows and Ubuntu partitions...
Code:
Disk /dev/sda: 250.0 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x07dccf10
[Code].....
I have a dual boot with vista on disk 0 and ubuntu on disk1. I just installed a disk 2 that I would like to use to try out other distros. Ubuntu is the only linux experience I have had. I'm really not very good at all of this, so my questions before I start loading another distro are:
1. Does Fedora use GRUB as its installer?
2. When I installed ubuntu on disk 1 (sdb1), the install was very simple. I chose sdb1 for the install, it loaded it, and when it was done I simply had the choice of which drive to boot into. Will installing Fedora on disk 2 (sdc1) be just as simple, or will I encounter steps I must take to make it so that I have a choice of which disk/OS to boot into?
I have a windows vista and fedora 11 64 bit dual boot. my diskstructure is as follows:
I have a swap of 6 gb.
I dont want to loose any of my existing OS's.
I am a linux newbie, I have messed with it some (backtrack) but I don't know a whole lot. I am going to networking security and I am in a linux class now. We are using fedora. On my laptop, I want to triple boot. Right now I have just 1 partition, with windows 7 ultimate x64 installed. I want to triple boot windows 7, windows xp x64, and fedora 12 x64. I am getting ready to format my laptop now with xp installing first. Then I will do windows 7, and then lastly fedora. Do I need to do anything special while installing fedora last? I have a 300gb hard drive, and I plan on having 100 for xp, 150 for 7, and the remainder for fedora.
View 2 Replies View Relatedi am using windows7 and ubuntu 10.04 in my system and dual booting... now i wanna install fedora 13 along with it ans make it triple boot... so can one pls help me in this process as i havent installed fedora before and i wanna be safe and dont want to loose my Grub or windows bootloader in this process
View 10 Replies View RelatedI think I've got myself into a bit of a situation. I've got 3 operating systems across 2 hard drives, and i need to get them loading properly.
I have my primary ubuntu 8.10 install @
/dev/sda1
I have a new Windows XP install @
/dev/sdb2
And I have a new install of Ubuntu 9.10 @
/dev/sdb3
I'd like to be able to selectively boot into all 3 until I can return my current 8.10 install. Can someone show me how to get my /boot/grub/menu.lst file in order?