Fedora Installation :: Triple Boot Vista 11 - 64 Bit And 11 - 32 Bit
Oct 2, 2009I have a windows vista and fedora 11 64 bit dual boot. my diskstructure is as follows:
I have a swap of 6 gb.
I dont want to loose any of my existing OS's.
I have a windows vista and fedora 11 64 bit dual boot. my diskstructure is as follows:
I have a swap of 6 gb.
I dont want to loose any of my existing OS's.
I recently installed ubuntu onto a pc running MS vista. Then I somehow managed to install a second instance of ubuntu. Both of these were on the (drive e Then because of HDD problems, I had to reformat my original drive with MS Vista (drive C). Because of installation problems with ms vista - I ended up installing it onto the drive e: also. But now I can no longer load ubuntu because the "GRUB" loader is missing. So my questions are:
1: How can I restore the "GRUB" loader? So I can access ubuntu again
2: How can I remove/uninstall the second ubuntu installation?
3: Is it possible to have a triple boot system with ms vista / ubuntu 32-bit / ubuntu 64-bit?
i'm trying to make my imac capable of triple boot.the software i use are:
mac os x 10.5.8
win vista sp1
linux opensuse 11.2
[code]....
How would I install OSX on my PC so it would still boot to GRUB? And how would I add OSX to GRUB? Or should I use some other bootloader?
View 4 Replies View RelatedOn installing a dual boot XP/OS 11.2 on a 40GB HDD, I had no problems with the partitioning, but now I have installed XP (15GB) and Vista (20GB), the OS 11.2 setup insists on shrinking the Vista partition to 15GB and does not allow me to change this.Have tried going into 'Create Partition Setup' and 'Custom Partition Setup' but can't seem to get Vista back to its original size
View 1 Replies View RelatedI have a dual boot with vista on disk 0 and ubuntu on disk1. I just installed a disk 2 that I would like to use to try out other distros. Ubuntu is the only linux experience I have had. I'm really not very good at all of this, so my questions before I start loading another distro are:
1. Does Fedora use GRUB as its installer?
2. When I installed ubuntu on disk 1 (sdb1), the install was very simple. I chose sdb1 for the install, it loaded it, and when it was done I simply had the choice of which drive to boot into. Will installing Fedora on disk 2 (sdc1) be just as simple, or will I encounter steps I must take to make it so that I have a choice of which disk/OS to boot into?
I am a linux newbie, I have messed with it some (backtrack) but I don't know a whole lot. I am going to networking security and I am in a linux class now. We are using fedora. On my laptop, I want to triple boot. Right now I have just 1 partition, with windows 7 ultimate x64 installed. I want to triple boot windows 7, windows xp x64, and fedora 12 x64. I am getting ready to format my laptop now with xp installing first. Then I will do windows 7, and then lastly fedora. Do I need to do anything special while installing fedora last? I have a 300gb hard drive, and I plan on having 100 for xp, 150 for 7, and the remainder for fedora.
View 2 Replies View Relatedi am using windows7 and ubuntu 10.04 in my system and dual booting... now i wanna install fedora 13 along with it ans make it triple boot... so can one pls help me in this process as i havent installed fedora before and i wanna be safe and dont want to loose my Grub or windows bootloader in this process
View 10 Replies View RelatedI have triple boot pc (xp, ubuntu, and fedora), installed in that order. xp and ubuntu seem to be stable. i have had to pull the power cord 3 or 4 times while booted in fedora. i noticed the last 2 times i can still move the mouse around, but can't get it to open anything. the keyboard is locked up, can't alt-f1 or f2 or anything to get console. can't get it to do anything, other than watch the mouse tail move around (weird).
i installed a new power supply (and at least i now have a power switch - the old one never had one), but that didn't fix the lock up problem. i haven't ran yum update since the fc10 live cd gnome install. was planning on doing that later.. not sure how long it will stay up to download all the 300 or so updates. right now the only thing open is a terminal (can't type in it).. what should i look at to fix this lock up problem?
I now have a triple boot on triple drives with Vista on sda, Ubuntu on sdb, and PCLinuxOS on sdc.When I installed PCLinuxOS on sdc, I installed the bootloader in the first sector of partition 1 of sdc so that I could keep using the Grub bootloader that installed with Ubuntu.Everything is working fine at the moment.I now want install Fedora 10 on sdc for experimentation. I have used gparted to create another partition on sdc to install Fedora 10, so my question is 'What and where exactly should I put in the /boot/grub/menu.lst of my original bootloader to get to Fedora?'
View 14 Replies View RelatedI am triple booting
Windows xp
UBUNTU 10.04
Fedora 13
Everything works fine, the setup went very well. But I got to thinking (A dangerous thing for me). In Ubuntu I am using separate partitions for / (root) and /home. I was wondering, during install of Fedora, could I use the separate partition I am using now for both root and /home for just / (root) and use the Ubuntu /home partition for Fedora (set the mount point for /home to the same partition as I did for Ubuntu and not format the drive)? This would allow me to seamlessly use the /home partition and not require duplication of files. I can mount the Ubuntu /home dir while in Fedora.I can share the /home partition with two different installs of Ubuntu (been there).
I need some help creating a triple boot system, I have already installed XP and W7, now I am installing Fedora 12 (this is for work so unfortunately it has to be like that). Now the problem is that I want it to show all the partitions in GRUB. Right now it works by going to GRUB first, when selecting Windows it jumps to the Win7 boot manager.
I tried to have them all in one but it seems like the addresses I used in GRUB did not work cause it keeps directing me to the Win7 BM. BTW I am using a single drive with 3 different logical partitions.
I had Win7 installed on my Laptop and wanted to set up a triple boot with Fedora 12 and Mint 8.So I installed Fedora 12 and it worked loading grub and offering Win7 and Fedora as choices.Then I installed Mint hoping for the Grub2 to recognise Fedora and set up the triple boot but it didn't and I can now only boot into Win7 or Mint.sudo update-grub doesn't help.How can I configure grub2 to offer me all three OSs?
View 1 Replies View RelatedI have an Intel DG33TL MB, Intel Core 2 Quad Q9650, 8GB SuperTalent DDR2-800, and 4 Seagate 500GB hard disks. The disks are connected to a 3Ware 9650SE-4LPML and set for RAID0. I partitioned the drive in the following manner: 900GB for XP-Pro x64 (first install), 100 GB XP-Pro (installed second), and the remaining for FC10. After installing FC10 x64 using downloaded DVD .iso I am getting the following error on reboot:
Code:
Reading all physical volumes. This may take a while...
Volume group "VolGroup00" not found.
[code]....
I had a dual boot working fine with XP and F12 on two physical drives, all was well. Last night my friend helped upgrade my system, I now have 3 drives (20gig F12) (60gig XP) and (320gig Win7) now the PC only loads Win7 as I think my friend told bios to boot from 320gig. Has anybody here got experience with triple boot from 3 drives? Here is my guess, tell bios to boot from other drive and add Win7 to grub. Not sure how but that's my guess. Also what worries me is that win7 does not "see" the other two drives.
View 5 Replies View RelatedI installed fedora 12 as second os along with ulimtate vista on 64 bit machine.
I was able finish the install and boot to fedora first time. but after updating the software , i am unable to boot into fedora but am able to boot in to vista.
I am using a HP Pavilion HDX9000 notebook series. it has 2 100gb hdd. vista is on c and fedora is on d. boot info was written to MBR on C drive.
Having a major issue with my laptop. I am unable to boot into my Vista installation.I am currently posting this through my Fedora 11 installation which I had already. If anyone is interested, the BSOD error is:
0x0000007B (0x80399BB0, 0xC0000034, 0x00000000, 0x00000000)
As far as I know, a '7B' BSOD is usually a hard disk error but I am 100% sure the HDD is fine as I can read and write from both Fedora and Knoppix without issue. Steps taken so far: Obviously, I have tried the usual steps of trying to start windows in safe mode, last good config, and all of the F8 options. When they failed, I used fedora to check for some solutions online (Mostly useless answers from MS) and I found one successful case when a person flashed his BIOS back to an earlier time. Unfortunately, I cant get the BIOS update I got from the Dell website to boot from a USB drive (Says invalid boot disc - the BIOS on it is in the .exe format which I can't use in linux) and I do not have a floppy drive on the laptop.
So, I put in my Dell drivers and utilities CD hoping that it would give me some option to update (Or roll back) the BIOS but there was no such option. However, it did give me a load of diagnostic options including repair options by symptom so went with the "Unable to boot from BIOS". Unfortunately, that didnt help me at all. So, I got my Vista installation disc (OEM supplied) and managed to get to the repair menu (Which I had among my F8 options anyway) but this also has the option to reinstall. Unfortunately, it states that "Upgrade is unavailable" and that a clean install is the only thing I can select (At the expense of my files and settings).
As for the repair options, the automatic recovery doesn't seem to find any errors, asks to reset and see if all is well (It isn't). For some reason, system restore doesn't detect any restore points. There are no windows memory errors detected and I have no backups. So, i'm left with a command prompt that, by default, is asking for a file in this folder: X:/WINDOWS/System32/ I have no idea where it is getting the X: drive from - I have C and D drives for windows only. As per another online guide, I tried:
[Code]....
I have a single hard-drive on a spare computer and I decided to try out Ubuntu on recommendation from a friend. I really like it now but at first I just dual-booted it, and now I want Vista gone. I know it's unnecessary to have just one OS but my hard-drive isn't particularly big and I'd prefer to have Ubuntu by itself. Can anyone tell me how to eliminate vista and leave Ubuntu as my sole operating system (I've all my files from computer on another computer so I don't have to worry about losing anything).
View 2 Replies View RelatedI installed Ubuntu 10.10 on my PC running Vista Home Basic. I installed to run as a dual boot but now I can only boot into Ubuntu. I have tried to run the recovery disk for Vista and it errors out also..
View 6 Replies View RelatedI'm brand new to Fedora. I ran the live cd and installed Fedora. I then installed OpenSUSE and Mint. When Mint formated the hard drive, Fedora wasn't in the graphic, even though sda1 was ext4 and sda3 was lvm2. When Mint rebotted, Mint and OpenSUSE were on the menu, but Fedora wasn't.
View 14 Replies View RelatedI installed fedora 10 on my laptop as a partition with vista. However i'm now not able to boot into my vista partition as everytime I try it comes with an error saying "bootmgr" is missing. Below is whats in my grub.conf file. However I am able to access my vista partition through fedora.
default=2
timeout=5
splashimage=(hd0,4)/grub/splash.xpm.gz
[code]....
I have a PC with two 40 Gb hard drives. Vista is currently installed on drive 0. Nothing is installed on drive 1. If I switch cables to the drives, Vista will be installed on drive 1. Nothing will be installed on drive 0. If I then install Fedora 10 on drive 0, will it automatically detect Vista on drive 1 and allow me the option of using Grub or something else to boot it? I want to avoid having Vista overwrite my MBR, but I don't want to piss my wife off because she can't access windows for two weeks while I figure out how to customize Grub or install something else. If I need to customize Grub, (or some other boot loader), I would need step by step instructions. Is there a book or online tutorial?
View 4 Replies View RelatedI just installed Fedora 12 on my Windows Vista machine.Now when I boot my computer it shows two optionsFedoraOtherThe `Other` one would be Windows Vista.Its okay if I boot into Fedora, but if I boot into Vista, I get the following error:
Code:
BOOTMGR is missing.
Press CTRL + ALT + DEL to reboot.
[code]...
I have a Computer, It came with Windows 7 64bit on it. I installed Ubuntu through WUBI. I used the Windows Disk Management program to resize my HDD. I shrunk the main drive and created a 20 gig free space. I installed WindowsXP on this 20g space. I had to change from AHCI to ATA. I started my new XP installation. As I should have expected my the screen that let me pick between Windows 7 and Ubuntu was gone, and it just said XP. Well thats cool. I get in XP use bcdeasy and use the install Win7 to mbr. So I restarted. Great I now I have Ubuntu and Win7... but no XP. So i think, okay, ill boot into Ubuntu, use the update grub command and XP will be there, so i do it and restart. No XP, So i try to boot into Win7 and see if i can do something in there.. No luck it says it can't boot and takes me to a startup recovery thing. Which, as Windows recovery things tend to do, doesn't find anything wrong. So I have Ubuntu now, which is great, but I do need Windows.
View 4 Replies View RelatedOne of the screens in the installer( middle of screen) will show what systems are on the grub menu, and one will be marked the default.
If the vista is not there (usually indicated by other), then click the add and select the correct boot partition (sda for vista) and change it's label to Windows Vista.
If other is there, click the edit button and change other to Windows Vista.
Finally, click the check box for the one you want to be the default boot. (you can always change that in the grub.conf later.)
I have Windows Vista Home Premium and I don't want to switch entirely to Fedora because I'm not as familiar with it as I am Windows. I mainly wanted to install Fedora for my Linux class at the Community College I attend. How do I install it with a dual boot so it doesn't take over Windows Vista? I had that happen once and it was a mess to fix and reinstall Windows Vista too.
View 7 Replies View RelatedI have been using Windows Vista since I bought my laptop. Due to the need to use another operating system, I decided to go for Fedora. I read a some installation guides and was told that dual-booting will allow me use both OS without problems.Last night, I created three partitions on the hard disk, one of them is the primary partition for my Vista OS. Then I went ahead to install Fedora on one of the other partitions. The Fedora worked fine. Subsequently, I wanted to check some stuffs using Vista, but the computer showed my some prompt that said that my BOOTMGR is missing. However, Fedora still boots and works perfectly.Please what should do? I didn't back up my documents before installing the Fedora. How do I go back to Vista without formatting my hard disk.
View 14 Replies View RelatedI have been messing around with F13 in VM VirtualBox for awhile now. I have read in some places that it is better to install F13 into its own partition on the hdd creating a dual boot system for, in my case, Vista and F13. Any truth to this? I have been having problems with system settings in F13 while using VB. i.e.: sometimes the system will see 3d support, other times it won't. Sometimes it will see ethernet eth0 and then other times it won't. All my hardware from my MB to Display is supported according to the documentation I have looked at.
View 2 Replies View RelatedI'm new to linux systems and just installed Fedora 14 onto my Windows Vista laptop. I chose the shrink existing system option and then proceeded to install Fedora. The only problem is that when I choose Other in the Grub boot menu my Windows Vista goes straight to the recovery screen and does not boot. I don't want to do a point recovery. Is Vista not running because I shrunk it or because of some configuration that I did not add in the Grub files. How to solve this problem and get Vista running properly from the dual boot menu?
View 2 Replies View RelatedMy laptop had Vista, I installed Lucid so I'm dualbooting with GRUB, and I'm wondering if anybody knows of a way to triple-boot with Mac OSX. Thanks in advance.
View 1 Replies View Related