Ubuntu Installation :: Disk Boot Failure After Fresh Install
Oct 16, 2010
After buying a new PC, I decided to "reorganize" my former PC as follows:Initially it has been a dual (SATA) disk dual boot PC- one disk for each OS, while XP was fully installed on a single NTFS partition. Using Gparted I shrunk the XP partition, and created some Linux partitions. I've verified that the XP partition (sda1) is bootable. Afterwards, I removed the other (former Linux) disk from the computer. While doing so, I had to temporarily disconnect cables from both drives. Finally, I fresh installed Mint 9 (Ubuntu 10.04 derivative), on my pre-prepared Linux partitions. Installation completed flawlessly, and during the install, I've noticed that GRUB2 has been installed on sda. Rebooted and got "Disk boot failure" error.
I've checked the BIOS and noticed that the (single) drive was not recognized.
I manually tested from the BIOS and located the drive as IDE3. Saving the new configuration (F10) and rebooting- the HD gain is not identified (the CMOS battery is fine- keeps time).
Booting a live CD I can see and access all above partitions.
View 2 Replies
ADVERTISEMENT
Feb 15, 2010
I've run the install to hard drive program three times over and each time I get "disk boot failure". I believe I've got Grub to install to the mbr but I am not sure.
System:
Barton 3200+ with 1GB of DDR1
Asus A7V333
High Point hard disk controller
other items
All the hard drives are hooked to the High Point controller. It recognizes all of them that have power hooked up and read/writes to them. Two have 98SE installs, the third is where I'm trying to install Fedora 12 to get away from some problems I'm having with 98SE.
The BIOS is set up to boot from the "SCSI device" which means it's booting from the High Point controller. The High Point lets me set a boot mark, which, when set to the Fedora drive, yields the disk boot failure no matter what I do to it.
View 2 Replies
View Related
Nov 17, 2010
I have experienced a failure in one disk in my 4 disk software RAID10setup, but a straightforward rebuild is thwarted by the fact that twoof the other disks are considered non-fresh and hence get kicked outof the array. This of course prevents the array from starting up.Here's more detail about my setup:I have 4 2TB SATA disks in RAID10.
Device Boot Start End Blocks Id System
/dev/sda1 1 243201 1953512001 fd Linux raid autodetect
/dev/sdc1 1 243201 1953512001 fd Linux raid autodetect
[code]....
View 1 Replies
View Related
Mar 18, 2010
Ubuntu/Linux operating systems. It installs just fine but after it reboots I get a "disk boot failure, insert system disk". I have searched around but I can't seem to find anything that works. There is only one hard drive in my computer and no other operating systems on it.
View 1 Replies
View Related
Feb 27, 2010
I just bought a brand new hardrive (40gb western digital) IDE, 10 pin.I have gone through the installation and partioned the hardrive, when it gets to 100% it asks me to reboot.So i take the disk out, and then it says DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER:So i press enter and i get the same message> How can i get Ubuntu to boot up?The computer is a 2003 Medion pc with 512mb of RAM And an AMD Athlon processor. The computer has a sticker on that says: Designed for windows xp.
View 9 Replies
View Related
Feb 15, 2011
after my upgrades i noticed one hard drive was acting funny i was gonna reformat the drive anyway to totally remove winblows from my system grub was installed on the boot sector of the drive that failed how can i get the next drive in line to boot if some one can get me to a howto or tell me what i need to do short there of reinstalling the operating system.
View 5 Replies
View Related
Jan 27, 2010
I have a dual boot machine (Win XP + Ubuntu 9.10 on separate physical drives) which was working fine. I now want to replace the Ubuntu 9.10 with LinuxMCE which is based on Ubuntu 8.10. Using the LinuxMCE install disk, I did a fresh install of Ubuntu 8.10 over the top of Ubuntu 9.10 (repartitioning the whole drive). On reboot, I now get a Grub "no such disk" error. I have run the boot info script which produced the following RESULT.txt:
Code:
Boot Info Summary:
=> Grub 2 is installed in the MBR of /dev/sda and looks for
(UUID=6a59ab9e-041f-41e2-b27c-02b8ada4c1af)/boot/grub.
=> Grub 0.97 is installed in the MBR of /dev/sdb and looks on the same drive
in partition #1 for /boot/grub/stage2 and /boot/grub/menu.lst.
=> Windows is installed in the MBR of /dev/sdc
[Code]....
View 5 Replies
View Related
Jun 11, 2009
I just upgraded via preupgrade-cli (from FC10), rebooted, the upgrade process completed, then the system rebooted and I just see a blinking white cursor now.I was able to boot up from a live cd of FC11, but I'm not sure how I can repair the system.
View 14 Replies
View Related
Jan 7, 2010
I bought a t770.uk HP desktop PC, which came without a Hard drive as the pervious owner had removed it for security reasons. A week later I got a hold of a brand new - out of an anti-static sealed bag - compatible Western Digital Caviar SE 80GB SATA150 7200 HDD, and installed it as directed by my t770.uk manual. Up until now, things looked to be on a roll. As I don't have any windows OS, I figured Ubunutu would be the way to go (and it certainly is from what I've heard and read about it. I can't wait!).
So I sent off for a CD and it popped through my mail a few weeks back. The problem that I am having is after booting past a very brief view of the HP POST screen, the screen goes black with the error "Disc boot failure-insert system disk and press enter". I've tried placing the Ubuntu disc in (assuming it is asking for that? An OS disc) and restarting, and changing the boot order around, but no matter what I do the error persists and I can't install Ubuntu. I really want to get this PC running with Ubuntu.
View 9 Replies
View Related
Oct 16, 2009
my Fedora 11 system is not starting anylonger. It stops with the message:
Code:
VFS: Can't find ext4 filesystem on dev dm-0
The system told me since a while, that a lot of the sectors of one disk of the (software) RAID compound are failed already. So tried to disconnect each of the disks and start them separately. Unfortunaltly this is not working (for one its is not working at all, the other wents the same far as with both), when I tried to recover the system with the Fedora DVD, it said no distribution found. I am quite new and do not know so much about linux system, so i do not know what further information you could need. Maybe it can be important, that both disks are encryped (the system wents so far, that I can type in the password).
View 2 Replies
View Related
May 10, 2011
I've just installed 'Testing' on a VMware server and after I completed the install with no problems, the system booted into the kernel and I noticed the following start up process error:
Code:
startpar: service(s) returned failure: udev...failure!!!
I have not seen this before and am not sure if it's related to the fact that this is a virtual machine and not a physical server or something else. Here is a Screenshot.
View 1 Replies
View Related
Jan 24, 2010
Code:
allen@heavy:/etc$ uname -a
Linux heavy 2.6.31-17-generic #54-Ubuntu SMP Thu Dec 10 16:20:31 UTC 2009 i686 GNU/Linux
FAT: IO charset ISO-8859-1 not found
I just recently installed Xubuntu 9.10 on my old acer Aspire 3000. Previously I was running Debian 5. Something it was great and all but I wanted to try out the "New Hotness" that is Xubuntu. The install went flawless and as far as Linux distro's go this is by far the most impressive. However, I have this problem with my USB storage devices not mounting. When I plug them in they show up and everything looks like its about to work when I get this: [URL]
A quick jaunt over to dmesg:
Code:
#
[ 2950.184072] usb 1-3: new high speed USB device using ehci_hcd and address 6
#
[ 2950.320178] usb 1-3: configuration #1 chosen from 1 choice
#
[ 2950.326192] scsi5 : SCSI emulation for USB Mass Storage devices
#
[ 2950.326513] usb-storage: device found at 6
#
[ 2950.326519] usb-storage: waiting for device to settle before scanning
#
[ 2955.324403] usb-storage: device scan complete .....
I've been all over google, in multiple irc rooms asking questions, and I cant seem to get anywhere. I can mount the devices manually with mount -t auto /dev/sdb1 /mountpoint. They mount themselves when I plug them in.
View 4 Replies
View Related
May 10, 2011
I've just installed 'Testing' on a VMware server and after I completed the install with no problems, the system booted into the kernel and I noticed the following start up process error:
startpar: service(s) returned failure: udev...failure!
I have not seen this before and am not sure if it's related to the fact that this is a virtual machine and not a physical server or something else.
Here is a Screenshot.
View 1 Replies
View Related
Mar 27, 2010
I need to re-install ubuntu but I also have windows on the same computer(GRUB). Can I just boot from cd? Is there and option in the live cd for reinstalls or do I have to destroy the partition?
View 3 Replies
View Related
Sep 13, 2010
Recently freshly reinstalled ubuntu 10.04 on a new / blank hard drive and it now crashes on startup. Quick version: I have a nvidia Quadro NVS 295, it gets to the point just after the bios with the flashing dash, seemingly tries to init xserver / gdm then crashes. Keyboard lights go off but the pc stays on, and just sits there with the monitor in power saving mode. Tried in recovery mode, the blue / grey ascii terminal thing pops up for less then a second then the display crashes in the same way.
Swapping with an ATI card borrowed from elsewhere, the new install will boot quite happily. Anyone know how I can get 10.04 to boot with a nvidia quadro NVS 295? Its a bog standard card and my version of 10.04 I upgraded to on my old hard drive works fine. ts a reasonably new dell XPS 64bit pc.
Longer version:
I run 3 monitors using a PCI-e x16 NVS 295 and a PCI NVS 295. This worked great under 9.10 and 10.04. Boss gave me a solid state HD so trying to install 10.04 on that. However on my first install attempt the live CD failed to load (same problem as above, gets to init'ing the display and crashes with no output). I removed the second PCI card to run with just the 1 PCI-e x16 nvidia card, this time the live CD worked fine and I could install, but I am stuck on the boot problem. Booted into the system using the ATI card and did an update just incase something may have changes / been fixed but the issue persists.
View 2 Replies
View Related
May 10, 2010
I admit that I am a noob - knows a little which makes it more dangerous than not knowing at all. in brief, I am unable to boot one of the OS out of 3 I have installed. Everything is fresh install on newly formatted partitions.
Here are the details:Two HDs - one is Sata and second is IDE. Win7 installed on IDE (sdb2) then Ubuntu 9.10 on Sata (sda2) and lastly Linux Mint on Sata (sda3). Everyone was on its place - that is - Ubuntu 9.10 on sda2, Linux-Mint on sda3 and Win7 on sdb2.
Future of the day was bright and promising until I upgraded online to 10.04. After that, I was only able to boot to Win7 (IDE drive - sdb2 - not sure if it changed at that point or not) but no nix OS on Sata sda2 & sda3. I downloaded 10.04 and installed from CD again on sda2. Well, now I am able to boot into Win7 and Ubuntu 10.04 but no Linux-Mint. Another interesting thing is that sda and sdb have interchanged/swapped. So now if I chcek it thru gparted or run boot script, Sata drive shows up as sdb and IDE is now sda. In another post, I read that grub2 does that and make IDE drive as the first drive and Sata drive as second. Well, I buy that but why I am unable to boot to second OS on the same Sata drive? Evidently, I am missing something and I take that it is mostly user error but please
[Code]...
View 8 Replies
View Related
May 22, 2010
I have a Sony Vaio PCG-k195hp laptop, in which i've installed Ubuntu 10.04. Before installation i tried the Livedisk environment to make sure that everything would work out okay.
The results were fine, ubuntu even got the onboard Wireless card working which was causing problems in windows. But after the install ubuntu has become erratic. It sometimes boots and does a lot of work but other times it'll boot and freeze as soon as i move the mouse, or even earlier. I am pretty certain the CD was not the cause as i've already used it to install 10.04 in another system and i'm writing from it right now. I got the 10.04 iso on the day it came out and thought that maybe it wasn't complete so tried updating my install, but it had an error during the update installation.
Now even the live CD won't work as it hangs in the loading screen.
View 9 Replies
View Related
Oct 23, 2010
I have some proprietory softwares installed on WinXP so it is very important for my work that it is up and running.
I performed a FULL INSTALL from the Live-CD (10.10) and installed grub on the windows partition.
Now whenever I try to select the Windows option in the Grub menu, the screen goes blank and it gets me back to the Grub menu.
View 9 Replies
View Related
Jan 16, 2010
when i try to boot from the disk i burned, the screen show to lines of code, then pauses and never continues with any process.
View 1 Replies
View Related
Jan 9, 2010
So I currently have an install of Karmic running that has been upgraded over the years but I am repartitioning my drives so I did a fresh install on a new drive.
My first problem was the live cd would not boot and I had to use the alternate cd to do the install. It would boot into a blank screen and the i915.modeset=0 kernel parameter did not help.
After the installation finished I went to try and boot and found that right when it went to initialize the graphics, my computer locked up hard. Keyboard unresponsive and all. I read the forums and I tried using the kernel parameter i915.modeset=0 and removed quiet and splash from the kernel line to see if I could spot any errors but nothing appeared.
I am able to boot into recovery mode, and I tried even running an apt-get upgrade to get all my packages up to date and installed the latest nvidia driver but still have this issue.
I'm at a loss as to what I should attempt next.
Here is boot info, just to clarify sda and sdb are a fakeraid on my old setup, sdc is my new install
Boot Info Summary:
View 1 Replies
View Related
Mar 12, 2010
I was able to boot up the live CD and install the OS to the hard disk. *Single boot.After I rebooted, the system loads up to the Ubuntu splash screen and will "eventually" move along. The problem is that once it moves past the splash screen, it starts blacking out the screen. It looks like the screen turns on for about 10 seconds and then off for another 10 seconds repeatedly. The screen blinks like this indefinitely.This is my first attempt at installing and or using Linux so I am an uber n00b.
** Also, I am able to ctrl + alt + f1 and get to the terminal so i should be able to run any commands without any trouble.
View 1 Replies
View Related
Jul 8, 2010
I boot up after a fresh install and I don't get a boot splash screen. I really cant find a way to fix and some times it does not go to the login screen.
View 1 Replies
View Related
Mar 21, 2010
When I install either desktop version of Ubuntu 9.10 or Xubantu 9.10 it boots ok when ask to reboot at the end of the install, but will not reboot after that (2nd attempt and all after fail)On 2nd and later attempts the grub menu comes up and I choose default Ubantu and the Ubuntu circle logo displays for about 30 seconds, and most of time I see it try to access my floppy drive (sometimes the floppy drive light stays on, sometimes it does not) a cursor then blinks in the upper left hand corner for about 10 seconds and then the screen goes blank and freezes there until I power down.
My System
Dell Dimension 2350
Celeron 1.80 G Hz
768 Meg RAM
30 Gig hard drive
Note: Xubantu installs OK to HD on another system I have, but not on this Dell. To test the Dell I did install Puppy Linux with default grub loader to HD ant it works OK (boots OK to HD each time).Side note: At first I tried this Dell to set up dual boot with XP and Ubantu and same symptoms Ubantu only booting OK once and then never again so I thought it was dual boot issue so I deleted all partions (XP is now gone) with latest GParted version and attempted installing Ubuntu 9.10 and then Xubanto 9.10 on the whole harddrive but still no boot past the first time I though this might not be a grub issue since it seems to get past grub and the Ubantu circle shows for about 30 seconds before the system freezes. only a guess on my part as I don't know enough about Grub or Ubuntu to troubleshoot without help. I see I can hit "e" to get to the grub editor and I looked at the grub boot code but don't enough about it to edit for a fix. I thought about Lilo but did not see an option on the normal Xbuntu ,or even when I used the alternate install CD,for a Lilo option. Also note I can run the live CDs for Ubuntu and Xubuntu OK on this Dell. Only HD install gives me problems.
View 2 Replies
View Related
May 8, 2011
I have spent ages looking at similar problems but not not quite the same. I have installed 11.4/Gnome (x86) and wanted to use my GT430 card. I went here: 'http://en.opensuse.org/SDB:NVIDIA_drivers' and used the 'one click' install for current cards. All went ok until I rebooted and I got a 'gdm[1239]: WARNING: GdmDisplay: display lasted 0.846578 seconds' message. I got five of these in succession until the 'gdm[1239]: WARNING: GdmLocalDisplayFactory: maximum number of X display failures reached: check X server log for errors' appeared and it popped me down to an init 3 login.
So, I deleted the blacklisting conf file so that I could get back in to Gnome on Nouveau (which I did ok). I then noticed there was no /etc/X11 Xorg.conf file so I ran /usr/lib/nvidia-xconfig to generate one (which it did) - but it made no difference. I am at a loss know after spending 8 hours on this. Any pointers would be greatly appreciated. My machine is still at fresh install state so even if I have to reinstall 11.4 it does not matter.
[Code]...
View 5 Replies
View Related
Nov 24, 2015
System is hanging during boot after a successful fresh install via netinstall disk. Never makes it to any GUI or prompt. However, it does still respond to CTRL-ALT-DEL (not completely frozen).Default debian installation with one exception - KDE checkbox was checked for installation. Everything else was default, with "use full disk with GRUB" option chosen.The boot process appears to hang during the service starts. It appears that the start job for "Create Static De..." is not actually ever completing. I don't know how to troubleshoot that any further than I have.
This is running on hardware, it is not a virtual machine. 480GB SSD, i7, 16GB of RAM, AMD R9 390 (I dunno if this is the problem, but it seems a likely culprit).There are no other disks attached. I have verified successful memtest completions (0 failures) and hard disk is intact and working fine (I have swapped for another disk, and the same thing happens as well).
My skill level with Linux is relatively low. I have proficiency using it and programming for it, but not much in the way of troubleshooting/ installation/ drivers.
Here is an album of "screenshots" (phone photos) of the boot sequence in debug: URL....I tried booting straight to console by removing "quiet" from boot options and changing to "text", but it does not alter the outcome in any discernible way.
View 6 Replies
View Related
Jan 12, 2009
I'm stuck with installing Fedora Core I have 2 hard drives both 80Gb I want to install a fresh copy on one of the drives to do a dual boot I have vista on the main hard drive this is where I am at Installation requires partitioning of your hard drive by default, a partitioning layout is chosen which is reasonable for most users. You can either choose to use this or create your owe. Select the drive to use for this installation?
View 10 Replies
View Related
Mar 12, 2010
I had ubu 904 and vista installed on an 80gb drive, i had a spare 80gb drive also. I setup a raid0 config in my bios, then installed ubu9.10 onto it. All was fine until the very end, and then it said grub failed to install.
So i rebooted, and im left with a blinking cursor. How do i install grub? Ive installed ubu a few times now and never had an issue so now im lost.
View 1 Replies
View Related
May 23, 2010
I want to properly install Unbuntu on my multi boot pc. I would like to install to E partition which is currently ntfs. I have never installed Linux. What drive should the boot loader go? I can format E partition during install? Does it still need a swap file partition? If so, can that be made from E partition? How big? I'd like to have a boot menu to choose Ubuntu or a choice that takes me to the windows boot loader. Would that boot loader get wiped if I did a fresh install of 7 to the I drive? Also, what would be the proper way to upgrade Ubuntu? I see a lot of post where people are doing it wrong.
Here is my drives layout. Should install Ubuntu to my SSD J drive instead? I tried the live CD. Seems to work well. I have a Asus Max Formula MB, Phenom II 6core, ATI 4870. MB has a built in Via sound card. Not sure if that was working.
View 1 Replies
View Related
May 3, 2011
Followed steps 2-5 and purged/reinstalled grub now it boots as it should, NO idea where it was messed up.[URL].. I had 9.10 running in raid1 and upgraded my hardware (cpu, mb, memory etc) and wanted to do a fresh install of 10.04 to get updated. After following the various guides online such as [URL]...It begins to load grub and drops to a "grub> " shell. Which I have to do the following to get it to boot.
Code:
set root=(md1)
linux /vmlinuz root=/dev/md1 ro
initrd /initrd.img
boot
Then it boots up normally and I can use it like any other desktop. I've been over my grub.cfg and /etc/defaut/grub files and cannot find the issue. At this point I'm wondering if the fact it's a raid1 setup is keeping grub from finding it's files.
[Code]...
View 9 Replies
View Related
Apr 3, 2009
Fc11 installed well, it was related to a particular sata driver perhaps The installation went well up to the reboot, and then displayed the message saying that LogVol00 was not found. 3ware sata raid card, usually it installs without error
View 2 Replies
View Related
