Ubuntu/Linux operating systems. It installs just fine but after it reboots I get a "disk boot failure, insert system disk". I have searched around but I can't seem to find anything that works. There is only one hard drive in my computer and no other operating systems on it.
View 1 Replies
After buying a new PC, I decided to "reorganize" my former PC as follows:Initially it has been a dual (SATA) disk dual boot PC- one disk for each OS, while XP was fully installed on a single NTFS partition. Using Gparted I shrunk the XP partition, and created some Linux partitions. I've verified that the XP partition (sda1) is bootable. Afterwards, I removed the other (former Linux) disk from the computer. While doing so, I had to temporarily disconnect cables from both drives. Finally, I fresh installed Mint 9 (Ubuntu 10.04 derivative), on my pre-prepared Linux partitions. Installation completed flawlessly, and during the install, I've noticed that GRUB2 has been installed on sda. Rebooted and got "Disk boot failure" error.
I've checked the BIOS and noticed that the (single) drive was not recognized.
I manually tested from the BIOS and located the drive as IDE3. Saving the new configuration (F10) and rebooting- the HD gain is not identified (the CMOS battery is fine- keeps time).
Booting a live CD I can see and access all above partitions.
I just bought a brand new hardrive (40gb western digital) IDE, 10 pin.I have gone through the installation and partioned the hardrive, when it gets to 100% it asks me to reboot.So i take the disk out, and then it says DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER:So i press enter and i get the same message> How can i get Ubuntu to boot up?The computer is a 2003 Medion pc with 512mb of RAM And an AMD Athlon processor. The computer has a sticker on that says: Designed for windows xp.
View 9 Replies View Relatedafter my upgrades i noticed one hard drive was acting funny i was gonna reformat the drive anyway to totally remove winblows from my system grub was installed on the boot sector of the drive that failed how can i get the next drive in line to boot if some one can get me to a howto or tell me what i need to do short there of reinstalling the operating system.
View 5 Replies View RelatedI just upgraded via preupgrade-cli (from FC10), rebooted, the upgrade process completed, then the system rebooted and I just see a blinking white cursor now.I was able to boot up from a live cd of FC11, but I'm not sure how I can repair the system.
View 14 Replies View RelatedI've run the install to hard drive program three times over and each time I get "disk boot failure". I believe I've got Grub to install to the mbr but I am not sure.
System:
Barton 3200+ with 1GB of DDR1
Asus A7V333
High Point hard disk controller
other items
All the hard drives are hooked to the High Point controller. It recognizes all of them that have power hooked up and read/writes to them. Two have 98SE installs, the third is where I'm trying to install Fedora 12 to get away from some problems I'm having with 98SE.
The BIOS is set up to boot from the "SCSI device" which means it's booting from the High Point controller. The High Point lets me set a boot mark, which, when set to the Fedora drive, yields the disk boot failure no matter what I do to it.
I bought a t770.uk HP desktop PC, which came without a Hard drive as the pervious owner had removed it for security reasons. A week later I got a hold of a brand new - out of an anti-static sealed bag - compatible Western Digital Caviar SE 80GB SATA150 7200 HDD, and installed it as directed by my t770.uk manual. Up until now, things looked to be on a roll. As I don't have any windows OS, I figured Ubunutu would be the way to go (and it certainly is from what I've heard and read about it. I can't wait!).
So I sent off for a CD and it popped through my mail a few weeks back. The problem that I am having is after booting past a very brief view of the HP POST screen, the screen goes black with the error "Disc boot failure-insert system disk and press enter". I've tried placing the Ubuntu disc in (assuming it is asking for that? An OS disc) and restarting, and changing the boot order around, but no matter what I do the error persists and I can't install Ubuntu. I really want to get this PC running with Ubuntu.
my Fedora 11 system is not starting anylonger. It stops with the message:
Code:
VFS: Can't find ext4 filesystem on dev dm-0
The system told me since a while, that a lot of the sectors of one disk of the (software) RAID compound are failed already. So tried to disconnect each of the disks and start them separately. Unfortunaltly this is not working (for one its is not working at all, the other wents the same far as with both), when I tried to recover the system with the Fedora DVD, it said no distribution found. I am quite new and do not know so much about linux system, so i do not know what further information you could need. Maybe it can be important, that both disks are encryped (the system wents so far, that I can type in the password).
when i try to boot from the disk i burned, the screen show to lines of code, then pauses and never continues with any process.
View 1 Replies View RelatedI have 2 USB drives. I have had 9.04 running on one for some time. I used Disk Creator in 9.04 to 'create' the drive. I use it as a reference to verify how things went in 9.04 if I hit a problem with 9.10.
However, after some months, when I tried this USB drive it produced this 'Boot Failure'. I followed up by checking the other USB drive which had Lubuntu installed via USB Disk Creator and it produced the same result ie 'Boot Failure'.
The Machine bios is set in the correct order.
I have tried to 're-do' things via 'Disk Creator' in 9.10 and 9.04 with the same result. It is not likely that both USB drives have failed at the same time.
Is Grub2 at fault in some way?
I'm trying to do exactly this: [URL] the first time i did it, I made it and everything was fine, except I didn't know what "installation size" meant in wubi, so as I selected 3GB, the rest of the partition was left empty and I didn't have enough space for ubuntu. Then I formatted the partition again and reinstalled ubuntu. Since then while it's booting, I get the message Disk boot failure insert system disk and press enter. I tried reinstalling many times, but I still get this message..
View 6 Replies View RelatedI'm getting a HDD Lock screen or Disk Controller Failure at boot up. (Compaq Armada) The HDD stops the system dead. The controller failure will allow me to boot Fedora or Puppy from the CD drive.
View 1 Replies View RelatedLast night when I turned on my lap top (5 year old Acer TravelMate 4650), it was not able to boot up (10.04 LTS). No system files could be read and a lot of error messages was displayed. In fact, it has done a few checks for disk error lately during boot up, but no further warnings given. I gave up recovering, and simply re-installed Ubntu 10.04. I was wondering if this could be related to a virus attack?
View 9 Replies View RelatedHere are my specs to start off...
OS: Corrupted Windows XP, Home Edition
CPU: Pentium 4 2.8GHz
RAM: 1gb
Graphic Card: nVidia GeForce 8600 GS
So I corrupted my Windows OS by doing something stupid so I decided to install Unbuntu. I tried installing it over my windows OS, but as it's scanning the disk it fails and says "Apt configuration failure" and then "installation failure". I can't upload my partitions because I can't run my OS to find them.
I know the information is limited I've considered trying to install a different linux OS or even format my entire harddrive (I would really prefer NOT to do that since I'd have to install all the drivers off the internet).
Keyboard and mouse failure when trying to run a live Ubuntu disk on an Acer Aspire M1641 desktop. I was trying to show off the Ubuntu system to a colleague when to my surprise as it booted up both keyboard and mouse died. There was no response at all, the only option was to use the power button, rebooting into Vista all back to normal. I tried several other versions of Ubuntu going back 8.04 even Knoppix failed to get the keyboard and mouse working. Even after re installing the windows drivers and several more attempts even changing keyboard and mouse, I could not get any linux live disk to work.
View 6 Replies View RelatedWinXp sp3 is on disk sdb, then installed Ubuntu 10.04 on sda, can go into diff OS without any problem. I am going to move sda to another machine, when I unplug sda, WinXp can't start to boot on sdb. How to fix it?below is my case output$ sudo fdisk -l
Disk /dev/sda: 160.0 GB
...
Device Boot Start End Blocks Id System
[code].....
After having tested Ubuttu 9.10 on a VM with Win XP Pro as host and running both Ubuntu 9.10 and 8.04 from a CD/CDR drive I decided to do an installation of 8.04 on a separate HD and import files.Installation seemed to work OK, but on reboot: no menu was shown to choose OS and the machine booted directly into Windows.Tried to boot directly from the "Ubuntu" HD in the BIOS boot menu and get the message "MBR error" full stop literally.The Ubuntu hard drive is no longer recognised in Windows , can't be acessed from the DOS prompt and obviously cannot be reformatted from there.Just for the record, I'm not totally excluding operator error from the cause
View 9 Replies View RelatedI have tried doing the edit as described but all that happens is a new page opens up with a document titled menu.lst.
View 9 Replies View RelatedI have a triple boot system running Ubuntu, WinXP, and Win7.I had Ubuntu running fine on its own partition (sda1) but an upgrade from Karmic to Lucid turned it into a dog.So I tar-ed my /home filesystem, split sda1 into 2 new extended partitions, then did a clean install of Lucid with / on sda5, and /home on sda6.I should also mention that I have already tried re-installing Grub from a live USB to no avail.
View 7 Replies View RelatedI was happily running 10.04--- really worked fantastically! Then, I updated all, and upgraded to 10.10 using the upgrade manager in Ubuntu Desktop. Now, when I choose Ubuntu from the boot page, the computer shuts down--- no errors, it just reboots and I get right back to the boot page. I cannot boot into Ubuntu at all, and I am now stuck with Windows 7 once again.
View 5 Replies View RelatedI'm having a few problems getting my system to boot after upgrading to 11.04.This problem actually first arose when I upgraded from 9.10 to 10.04 a couple of weeks ago, however I found I was able to boot by loading a selecting a previous kernel version (2.6.31.22 was the latest version I could successful boot from) and as I was a bit busy with exams at the time I decided to leave it be temporarily as I at least had a functioning system.I upgraded from 10.04 to 10.10 and then finally to 11.04 today. The original problem persisted on the upgrade to 10.10 however I was at that point still able to boot using the older kernel version. On the restart after the upgrade to 11.04 however, the system now freezes when trying to boot from 2.6.31.22 or previous versions (the splash screen shows and then the system gets stuck on a blank screen with just a cursor visible, but remains responsive to mouse (cursor moves) and keyboard (goes into restart process on Ctrl-Alt-Del)).
I'm at a bit of a loss of what to do and would be massively grateful if anyone had any advice of where to start for a solution. I can access the system using a LiveCD - the output of the boot info script is attached.
I installed Debian on my PC with a Acer Stock motherboard (xc600) with amd64 and after the installation finished it told me to remove my installation media and reboot. After reboot I was returned this message ' ERROR: No boot disk has been detected or the disk has failed.'. I have verified with gparted using mint live OS that I have Debian installed on my system.
I got believes that this may have be caused by a broken grub or I need to configure something I don't know how in BIOS.
I will update the topic later..
My installation media was a USB 2.0 flashdrive with a Debian 8.2 Jessie Installer and 9 different Linux distros. I have installed Debian multiple times before on my laptop and never had this problem so I know how to go through the installation process and set the partitions.
When I install either desktop version of Ubuntu 9.10 or Xubantu 9.10 it boots ok when ask to reboot at the end of the install, but will not reboot after that (2nd attempt and all after fail)On 2nd and later attempts the grub menu comes up and I choose default Ubantu and the Ubuntu circle logo displays for about 30 seconds, and most of time I see it try to access my floppy drive (sometimes the floppy drive light stays on, sometimes it does not) a cursor then blinks in the upper left hand corner for about 10 seconds and then the screen goes blank and freezes there until I power down.
My System
Dell Dimension 2350
Celeron 1.80 G Hz
768 Meg RAM
30 Gig hard drive
Note: Xubantu installs OK to HD on another system I have, but not on this Dell. To test the Dell I did install Puppy Linux with default grub loader to HD ant it works OK (boots OK to HD each time).Side note: At first I tried this Dell to set up dual boot with XP and Ubantu and same symptoms Ubantu only booting OK once and then never again so I thought it was dual boot issue so I deleted all partions (XP is now gone) with latest GParted version and attempted installing Ubuntu 9.10 and then Xubanto 9.10 on the whole harddrive but still no boot past the first time I though this might not be a grub issue since it seems to get past grub and the Ubantu circle shows for about 30 seconds before the system freezes. only a guess on my part as I don't know enough about Grub or Ubuntu to troubleshoot without help. I see I can hit "e" to get to the grub editor and I looked at the grub boot code but don't enough about it to edit for a fix. I thought about Lilo but did not see an option on the normal Xbuntu ,or even when I used the alternate install CD,for a Lilo option. Also note I can run the live CDs for Ubuntu and Xubuntu OK on this Dell. Only HD install gives me problems.
After performing the periodic update on 2010-05-26 including libc, libc6 and libgtk2.0 my system fails on boot with the following error message:
Code:
run-init: /sbin/init: no such file or directory
Kernel panic - not syncing: Attempted to kill init! If I boot from the 10.04 live CD, all partitions on the hard drive are visible, mountable, and pass all file system checks.
I have 3 separate hard drives, I IDE and 2 SATA. The IDE has side by side installation of Windows XP and Ubuntu. The 2 sata drives each have Ubuntu only. I upgraded the 2 separate drives to 10.04. with no problems I then upgraded the dual boot Ubuntu to 10.04 and it would no longer boot I formatted the partition and did a clean install of 10.04 Thereafter the Ubuntu on the dual boot drive will boot but windows will not nor will either of the 2 separate drives. Results text from boot info search is attached. I can access the 2 Ubuntu drives through the funcitonal Ubuntu on the dual boot drive, but cannot boot them.
View 1 Replies View RelatedThis morning my update manager came up so I clicked to update. About halfway through the update an error message popped up & said to restart my system. I restarted my system and now have a black screen with the following message:
mountall: symbol lookup error: mountall: undefined symbol: udev_monitor_filter_a
dd_match_subsystem_devtype
init: mountall main process (344) terminated with status 127
I read around earlier & tried to use a Ubuntu disk and reboot but I have the same error.
I'm using a Dell Inspiron computer, it's just over a year old. I keep up with all the updates but unfortunately cannot say for sure which updates were taking place because I just hit the update box.
After I upgraded to 10.04 using the prompt for an upgrade. Ubuntu failed to boot. PC starts but during boot hangs after ubuntu symbol and screen goes black and PC overheats. Same problem when booting off CD. I removed HDD and rigged it up as a USB) but can't read the the disk in windows. The PC works fine using old windows HD. What do I do?
PC:IBM Thinkpad G40 (laptop)
Ram: 1Gb
After a kernel update ubuntu would not boot. So found this procedure using the live update cd. Update grub.cfg & delete everything down to but not including the first line that starts with 'menuentry' . Then boot works ok. A couple of weeks ago it started on my notebook. Is anyone @ hq listening & able to fix this problem permanently?
View 9 Replies View RelatedI have a (slightly complicated) dual/multi boot system.
I keep getting boot errors (when choosing ubuntu from the grub2 menu)
Code:
Serious errors were found while checking the disk drive for /boot
If I switch off and restart, ubuntu will then start without issue.
My setup is like this ....3 disks, one with 10.10 clean install - so Grub2, separate partitions for /, /boot and /home, one with windows 7, one with windows XP and 10.04 wubi (this is my old disk which I will trash once I'm happy with my upgrade to 10.10 & 7 on separate disks.
I installed 7 and 10.10 with ONLY their disks installed. After both were working, I added all disks and rejigged the grub2 menu (using update-grub and StartUp-Manager).
This problem only seems to occur if my previous boot was not 10.10 ( I will investigate this further). It's as if something (grub2 ?, the bios ?) is remembering part of the previous boot and not using the grub2 menu completely.
I downloaded the Fedora live dvd iso file, burned it to a dvd. I was wondering if I forgot to do something or did I do something wrong. When I try to install from the dvd I get this error message, isoLinux: Disk error 80 , AX = 42A7 , drive 9F Boot Failed: press key to retry When I press a key to retry I get the same error. I also tried to install virtual pc and get not boot disk found.
View 3 Replies View Related
