OpenSUSE Wireless :: Sumvision SVW322U (rt3072 Chipset) Ifup Will Not Connect Howerer KDE NM Does
Sep 14, 2011
I have the above mentioned USB Wifi Dongle Bus 002 Device 003: ID 148f:3072 Ralink Technology, Corp. RT3072 Wireless Adapter It works extremely well using the KDE network manager but just will not connect using ifup traditional method through yast.
Initially it was using the RT2870 driver but this only gave wirelessg speeds (and still no ifup) but after blacklisting RT2780 and using RT5370sta driver draftn speed was achieved using KDE network manager however I still could not connect through ifup. The dongle scans and sees networks using ifup but will just not connect properly (NB security WPA2-AES).
View 9 Replies
ADVERTISEMENT
Sep 29, 2010
After spending quite some time on this, I have narrowed it down to:
Adapter works OK with NetworkManager
Adapter works OK with ifup if I run iwconfig after ifup has finished
It eppears to be linked to another thread Probl me de r seau wifi / Network manager in that dhcp needs to be running. (So it may be a 'feature' of RTL819 adaptors) So I've finally worked out that I need to start dhcp first.
[Code]...
View 2 Replies
View Related
Apr 28, 2011
I am running my wifi using YAST and IFUP. The card is a zd1211, and works just fine. However lately I have have to "start" it manually after booting. The only way I have found to do this is to open YAST >network settings> and "edit" the card, but NOT change anything, just click through the next buttons and it connects. I have tried using the settings "on boot" and "on hotpug" but always when I reboot, I have to go through the YAST rigmarole. This is a PITA. I am trying to avoid NM as I want to sort this out, not cover it up with more software.
View 4 Replies
View Related
Nov 29, 2010
NetworkManager? I have OpenSUSE 11.3 and broadcom wifi module. By default network are managed by NetworkManager. Wifi works great on opened access points. But when i tried to connect to WEP access point my hexadecimal key rejected. When i used ifup instead of NetworkManager the same key has been accepted. But i won't use ifup.
View 9 Replies
View Related
Mar 13, 2011
I have just installed 11.4 KDE (having used 11.3 for a while). I was able to use YAST in 11.3 to switch from network manager, to using 'traditional', to connect to wireless network without problems. Since installing (fresh install) 11.4, only network manager seems to work without issue;
using traditional never sets up the wireless connection - or should i say appears not to as no apps will connect (as they do fine using the network manager connection). using 'ifstatus wlan0', seems to suggest there is no configuration file when using the 'traditional' gui. Has any one had similar problems
View 9 Replies
View Related
Feb 19, 2011
I just installed OpenSuSE 11.3 on an old IBM T20 I had kicking around and I'm using a Proxim Wireless PCMCIA Card (Atheros AR5001X). Since this laptop does not have a DVD drive I installed the system using the Netboot CD and have the SuSE 11.3 ISO on an NFS/SAMBA file server. The issues appeared after the first reboot, the adapter no longer worked. I resorted to using the wired interface to finish the install.
Once the system was up followed the trouble shooting steps outlined in various places and found the ESSID is not being picked up by the ifup scripts. Not sure if it matters but I have ESSID broadcasts turned off on all my WAPs.
The ESSID is in ifcfg-wlan0. To get wireless working I have to manually issue iwconfig wlan0 essid "xxxx"..
Both networkmanager and ifup fail..
View 9 Replies
View Related
Aug 18, 2010
this is my first attempt to get into Linux (10.04 Lucid Lynx), and I'm eager to learn. The problem is however that i can't connect to the internet using my USB wifi dongle (Jensen 25150). I've tried what this link says:I've tried to blacklist rt2800usb, rt2x00lib, rt2x00usb and rt2870sta and to load "/etc/modules/rt3070sta", but no luck in that, so I simply do not know what to do next. Perhaps I haven't blacklisted them the right way? I've typed in the commands and saved Gedit and closed it. Is that the right way?
View 2 Replies
View Related
Feb 7, 2009
I have an intel 5300 wireless chipset which is not supported in kernel 2.6.25. I am currently using opensuse 11.0, I downgraded from 11.1 since I faced so many other problems. can I setup my wireless driver under kernel 2.6.25? if so, how could i do this?
View 7 Replies
View Related
Jan 18, 2010
I have a HP Pavilion dv2000 and can not figure out what chipset I have.
/sbin/lspci brings up the following
bunnyman@linux-bqo4:~> /sbin/lspci
00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile Integrated Graphics Controller (rev 0c)
[Code]....
where I can get the .inf file from? I took windows completely off of the computer and dont want to reinstall it just to get the driver.
View 9 Replies
View Related
Jun 16, 2011
Perhaps this is sheer ignorance, but i just cant figure out which wireless chipset i´ve got. Its irrelevant to say that my wireless conection doesn´t authenticate (repeating the process without end). So this is the output of lspci:
linux-wghx:~ # lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port (virtual PCI-to-PCI bridge)
[Code].....
View 2 Replies
View Related
Apr 19, 2010
is there any difference between ifup and ifplug?or they just do the thing.
View 4 Replies
View Related
Apr 22, 2010
In Network Settings in OpenSuse 11.1 while using "Traditional Method with ifup" I am able to set up a box as a server and connect via http over the net BUT Firefox cannot browse. If I switch to "User Controlled with NetworkManager" I can run Firefox but my server is not contactable. How do I do both?
View 4 Replies
View Related
Apr 17, 2010
at start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
[Code]...
View 2 Replies
View Related
Apr 13, 2010
On Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
View 5 Replies
View Related
Sep 30, 2010
I've got openSUSE 11.3 running via liveUSB on a netbook and no matter how many times I try, I cannot get wireless to connect to my network.
My network is:
- non-broadcast
- WPA2 Personal
- G
The netbook is fairly recent from Asus and wireless works perfectly with Fedora 11 and Windows XP.
View 5 Replies
View Related
Apr 8, 2010
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies
View Related
Mar 24, 2011
I had to uninstall a proprietary ATI driver because it wrecked my X server. Apparently I removed the wrong package, because now the X server won't even start, even with the "nomodeset" flag.
QUESTION 1.How can I configure WiFi on the command line with NetworkManager or ifup, whichever is easier?
QUESTION 2.Which packages do I need to download to restore the X server?
View 9 Replies
View Related
Mar 29, 2010
I have searched around a bit for a knetwork manager issue I am having on my opensuse 11.2 32 bit install. My wireless card is an 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) I am currently using the Broadcom wl driver
I am on the Internet with this machine as I am typing using the older "ifup" method. I am having great difficulty connecting to the Internet when I use knetwork manger though. The strange part is when I am connected to my router with knetwork manager, I can log into my Router, but I can not get to any web-page/ping any outside address.
so far the best (I was able to locate) advice I was able to get is located in this post. < Broadcom wireless, partchy internet - openSUSE Forums > following a posted how to to disable IPV6 (I suspect this may be the issue??), I was unable to locate modprobe.conf, or modprobe.conf.local, even after I updated via updatdb. I gave a shot at entering in "disable_ipv6=1" into "menu.lst". However, this did not solve my issue with knetwork manager. If my network information is needed when I am "connected" utilizing knetwork manager
View 9 Replies
View Related
Jan 15, 2010
I just upgraded and then re-downgraded kde and wireless has stopped connecting (it still seems to be working, just not the way it should). Here's some info:
Code:
/sbin/lspci -v
06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
Subsystem: Intel Corporation Device
[Code]....
View 8 Replies
View Related
Jun 6, 2010
I can connect to my wireless router while logged in as root, but not under my user account. I went into YAST and the user maintenance area and gave myself every permission (Add, Edit, Delete Users or Accounts), but kde network maanger will not allow me to connect to my router.
View 5 Replies
View Related
Nov 5, 2010
I'm moving from other distros. and I'm currently loving openSUSE and I'm probably going to stick with it for a long time.I have already googled for this, but I found no solution, but I figured this should be a common problem... Does google searches inside this forum?Now... for my problem, whenever I hibernate (suspend to disk) or sleep (suspend to ram) I can't resume my wireless connection nor connect to another.I don't know if this is an issue if I use cables, because I simply don't with my netbook:The hardware in question is an ASUS 1005HA eee pc, running openSUSE version is 11.3 fully updated. Didn't mess with wireless connections, nor kernel or hibernate settings
View 9 Replies
View Related
Feb 18, 2011
I have loaded the latest version of opensuse and I have everything working but I cannot connect to my wireless WPA2 network. I have downloaded the bcm43xx firmware using the method /usr/sbin/install_bcm43xx_firmware I then restarted the network. The computer will now read the network card and will find networks but I cannot get it to connect at all. At first it would connect using ifup in yast but would disconnect after a few seconds. It would never connect through NM. I have a usb network card that works just fine. I am lost as to how to fix this problem.
View 6 Replies
View Related
Jan 16, 2010
I recently bought Dell Studio 15 laptop, installed OpenSUSE11.2/64 in addition to Win7 64 bit. I am trying to connect it to my wireless network at home and at work, but without much luck.
1)Found out that Dell 1520 WLAN adapter has Broadcom 4353 chipset.
2)saw that b43-fwcutter installed
3)installed broadcom-wl and broadcom-wl-kmp-desktop
After that can see many wireless Access Points at home,selected one via NetworkManager (eth1), configured it (incl. security same as in Win7), it goes from Activating to Active, but I still can not connect - I mean, in the FireFox - "page not found"
iwlist scan (for my desired AP):
Cell 03 - Address: 00:E0:98:FA:5D:1A
ESSID:"Blackhawk"
Mode:Managed
[code]....
I can easily connect to WLAN at home and at work in Win7.
View 8 Replies
View Related
Apr 11, 2010
One of the biggest issues i have at the moment is that my network based plasmoids on my KDE desktop load before my wireless network connection is established, so i'm thinking it would be best to start up the wireless connection at boot time. On previous distro's, I did this with netcfg but I can't seem to figure out how to do so in OpenSUSE 11.2. Is this the best way to manage this issue or is it possible to set a delay before the plasmoids load up?
View 5 Replies
View Related
Feb 12, 2011
I read the thread about the b43-tools but the git command on there fails.
git clone [URL] Initialized empty Git repository in /sbin/b43-tools/.git/ fatal: [URL] not found: did you run git update-server-info on the server? I am assuming the server is them not me? I have installed the firmware per my dmeg request. And the firmware is installed correctly.
[Code]....
The card works it just will not connect. I think I have that rev 3 issue where I need to edit the SPROM but I can not seem to get the b43-tools installed.
View 9 Replies
View Related
Jun 28, 2011
I need help configuring to set my wireless to connect automatically on boot up. Right now I do have wallet on with a password.
View 1 Replies
View Related
Jul 27, 2011
My wireless is a libertas 88w8335. Suse 11.4 just installed. For this one, I need a windows driver with ndiswrapper. ndiswrapper is installed, and the driver as well.
I can see my networks with iwlist scan my network is set up in yast with ifup (I can scan the networks and find mine), but I cannot connect to my Acces point : there is no SSID with iwconfig.
View 8 Replies
View Related
May 13, 2010
I can't use my wireless card in slack 13.1 (slack64-current). Looking at the dmesg output I saw that the firmware was missing, so I download it from ralink website.After this I was able to up it with ifconfig. I also was able to see my network with wicd, but after connection I can only transfer very few packets and network becomes unresponsive, no traffic.In slack64 13.0 this same card works fine. I don't even need to install a firmware. how I can make this work in slackware64-current?
View 6 Replies
View Related
Mar 25, 2010
Does the rt61 dlink wifi adapter work with slackware 13?
Code:
View 4 Replies
View Related
Aug 20, 2010
Unable to connect to wireless network at home. The wireless network is visible. Password is requested. But no connection established.
hardware:
desktop, ubuntu 10.04
PCI card: sitecom wireless nework cardbus card 300N
chipset: ralink RT2800 802.11n PCI
iwconfig wlan0: RT2860 wireless, nickname: rt2860sta
I tried using ndiswrapper. Conclusion: 'driver already installed'.
The wireless network does connect on my laptop with ubuntu 10.04 installed. Distance to modem: 3 feet.
View 2 Replies
View Related
