Ubuntu Networking :: Unable To Connect To Sitecom Wl-181, Chipset Ralink Rt2800 802.11n Pci
Aug 20, 2010
Unable to connect to wireless network at home. The wireless network is visible. Password is requested. But no connection established.
hardware:
desktop, ubuntu 10.04
PCI card: sitecom wireless nework cardbus card 300N
chipset: ralink RT2800 802.11n PCI
iwconfig wlan0: RT2860 wireless, nickname: rt2860sta
I tried using ndiswrapper. Conclusion: 'driver already installed'.
The wireless network does connect on my laptop with ubuntu 10.04 installed. Distance to modem: 3 feet.
View 2 Replies
ADVERTISEMENT
Aug 18, 2010
this is my first attempt to get into Linux (10.04 Lucid Lynx), and I'm eager to learn. The problem is however that i can't connect to the internet using my USB wifi dongle (Jensen 25150). I've tried what this link says:I've tried to blacklist rt2800usb, rt2x00lib, rt2x00usb and rt2870sta and to load "/etc/modules/rt3070sta", but no luck in that, so I simply do not know what to do next. Perhaps I haven't blacklisted them the right way? I've typed in the commands and saved Gedit and closed it. Is that the right way?
View 2 Replies
View Related
Aug 23, 2010
I have Debian 5.0.3 and I've had a lot of trouble installing Linsys WMP600N PCI card - Ralink chipset - 2860. I had it installed in the board, before I installed/compiled Debian. What I'm thinking I should have done was chosen Desktop and Laptop during the guided install. I tried expert install, but I was over-whelmed with options. Anyways, I tried NDISwrapper in many different ways. My last tries showed that the driver and device was working. No matter what I did, I would never get an interface with a wireless extension. I couldn't find any useful information anywhere, including Ubuntu forums - I'm sure you think I'm stupid or evil.
I eventually figured I would get the drivers directly from Ralink website. [URL] The one that looked like it would work (RT2860PCI/mPCI/CB/PCIe(RT2760/RT2790/RT2860/RT2890) would error out when I would try to extract anything. I used 2nd one (RT2860WebUI) which worked. If anyone does use it, be sure to read all documentation that is included, including the README. After I was done installing/compiling it, I got ra0 interface and could see my router.
I couldn't connect to it because I use WPA2 and that wasn't an option for encryption. I will work on that later. I wanted to share this information with anyone who might need this.
View 1 Replies
View Related
Oct 29, 2010
other forums to get my Zonet ZEW1642D to work on my new install of Ubuntu Studio 10.10. None of the how-tos I've found APPEAR to have worked although I guess I'm not entirely sure how I would know. There is a pair of computers at the top right of my screen by the date/time. When I right click there the following are all checked:
Enable Networking
Enable Wireless
Enable Notifications
but when I click Connection Information Auto eth0 is the only connection that comes up (which must be the wired connection I'm using to submit this) Here are the things I've tried:
1) README_STA included in the driver files downloaded from the Ralink website although I must admit this was a bit over my head
2) http://ubuntuforums.org/showthread.php?t=1045703
3) http://www.hyperborea.org/journal/20...i-ralink-3062/
[Code]....
View 9 Replies
View Related
Sep 5, 2010
Just installed Ubuntu Studio 10.04 and everything seems to be working nicely except I have no networking.
The card does not appear in the Network Settings GUI. The only 3 tabs I have are General, DNS, and Hosts.
A screen grab is attached.
I'm a long time Windows user trying out some of the best Linux creative apps I can find. So, Ubuntu Studio was a no brainer. I checked the manufacturer's site for linux drivers and they are available, but I don't know how current. (Edimax site, not RaLink's site.) I opened the file and it looks like it needs to be compiled and installed to work. Something I know almost nothing about. The card is listed as supported in this forum for Ubuntu 9x but I can't find information about it for 10.04
PS. I have no networking on the system but I can transfer files via USB flash drives if needed.
Some System info:
Code:
1 ) Machine Brand and Model (PC/Laptop): Dell Precision 650
2 ) Wireless Brand, Model and Wireless Chipset: 03:0c.0 Network controller: RaLink RT2561/RT61 802.11g PCI
3 ) check interface: robert@ubuntu:~$ ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
[Code].....
View 1 Replies
View Related
Aug 4, 2011
I have new emachine 1401 and I can't get it to connect to wireless. It does detect networks but when connecting keeps asking for password over and over and never connects. I don't have wired connection at all and the wifi router is not managed by me, so I'm retyping output through my windows xp samsung netbook which works over the same wireless network...
I have tries some other solutions I found around here (install bcmwl-kernel-source, rt3090-dkms_2.4.0.4, blacklist rt2800pci...) so it's not original configuration but behaves exactly the same.
[Code]..
View 2 Replies
View Related
May 8, 2010
After installing Lucid, I noticed that my Ralink RT2860 card would not connect to my home network using WPA2 despite the network being visible and of good strength. So I followed the guide at [url] in order to install the newest Ralink drivers.
After installation, same issue. That is, the card will connect to my a/b/g/n network if I leave it unprotected, but it will not connect to the same network if switch it to WPA2. After being given the passphrase, the wireless icon on the indicator applet shows that it is trying to connect, but after awhile it fails. Does anyone know why the built-in driver and also the official Ralink driver are no good for WPA2 in Ubuntu 10.4 for my RT2860 card?
View 9 Replies
View Related
Oct 19, 2010
I have an HP DV6 3143se which has a Ralink 3090 wifi card in it.the only thing that doesn't work at the moment is the Wifi. I tried installing the Linux backports module, but the trouble is that sometimes, my home wifi network is shown on the list of available networks and most often, it's not. when the network does show up, and i click on it and enter my WPA2 password, it takes ages to handshake and then it tells me that my password is wrong. the same password works in windows 7 so something's not working.
when i try to disable and re enable wireless network on the network manager applet, i get a Wireless device not ready or Network manager not running message.
[Code]....
View 9 Replies
View Related
Aug 6, 2010
I just installed Fedora 13, and now I figured, maybe I don't know so much about pc anyway. Before I tell you my problem, I would like to say that I know a lot about windows, but about linux, I don't know anything. A plain beginner. And about my problem, it's more like a "how to" question than a problem.
You see, I don't know how to set up the wifi? The pc has installed wifi, and all I need to know is how I can connect to the internet. In windows you would usually just press the connection icon and then choose witch network you would like to access, and then eventually type in the password, and there you go. But it seems it's a little more advanced at Fedora. But I will give it a shot.
View 11 Replies
View Related
Apr 23, 2010
My wireless card disconnects frequently and sometimes it won't even connect at all. I've googled the card and the driver and it looks like others are having similar issues as well. [url]-[url]
My lspci | grep -i network is as follows
Code:
Under iwconfig, it's identified as wlan0, and I'm running kernel x86_64 2.6.32.9
View 5 Replies
View Related
Jan 8, 2011
Just posting this so others can find the solution more easily than I did.My HP ProBook 4520s had a blinking/flashing wireless indicator LED and the connection was unstable. The solution was to blacklist the rt2800pci drivers. This leaves the rt2860sta drivers, which work fine for me (so far). The device is actually a RaLink RT3090 and apparently they release drivers on their web site, but I did not want to go through the trouble of building it and did not find it packaged for 10.10.To try this fix, open up the blacklist file.
Code:
gksudo gedit /etc/modprobe.d/blacklist.conf
And add this line at the end...
[code]....
View 3 Replies
View Related
Jan 1, 2010
I am trying to get the above wireless adapter o work with Ubuntu. I have installed ndiswrapper but I am unsure what windows driver I need that will work with it.
When I type lsusb I get the following: Bus 001 Device 002: ID 0df6:0042 Sitecom Europe B.V.
I tried searching the ndiswraper site but all I could find was Sitecom WL-344 300N X2 Wireless USB Adapter that pointed me to Driver: rt2870.inf and rt2870.sys (on Windows XP).
I am not sure if this will work or where to download these files, so I was wondering if anyone else has this adapter that could shed some light onto how to get it working.
Edit: I just tried the rt2870 driver and it didnt work
View 1 Replies
View Related
Jun 20, 2010
I'm running ubuntu 10.04 with the sitecom wl-344 USB wireless networking dongle. I read that the device should work with the rt2800usb driver however I get this error in the terminal:
Code:
michael@michael-desktop:~$ lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 004: ID 046d:c71c Logitech, Inc.
[Code]...
View 6 Replies
View Related
Apr 4, 2010
I've just installed Ubuntu (Koala) on an old (but worthy) Toshiba laptop. It's got a Sitecom WL-140 wireless card. (BTW I'm new to Ubuntu, but an old hand at Solaris). Can't get the card to work, although I think It's nearly there. nm-tool shows driver is p54pci. The activity light shows an orange light occasionally. State is disconnected. I'm not really sure whether I should be using the supplied driver (p54pci) or the Windows driver for this card and ndiswrapper. I've installed the Windows driver with ndiswrapper thinking this may fix it but no.
ndiswrapper -l says wlancig: driver installed and device (1260:3886) present.
View 1 Replies
View Related
Mar 15, 2011
I am new to ubuntu, installed 10.10 on dell 250n. I am trying to use a Sitecom WL-011v2 wireless PC card.
View 3 Replies
View Related
Jul 16, 2011
I bought myself a Sitecom Wireless Network USB Micro Adapter 300N X3 (Sitecom WL-364) today. When I place the adapter in my PC, it is not recognised as a wireless adapter.
There are similar posts like this one, most of them are about conflicting drivers. According to this post I shouldn't be worried about that (as I'm working in 11.04 32-bit).
The output of lsusb is this:
Code:
Bus 001 Device 003: ID 0df6:0051 Sitecom Europe B.V.
Also, I was having a hard time getting to know the chipset of the adapter. Is RT2870 the right driver for the adapter?
View 1 Replies
View Related
Nov 21, 2010
how to use the Sitecom WL-324 usb stick with ubuntu (10.10)? (It works with windows.)
lsusb | grep Ralink
Code:
Bus 002 Device 004: ID 148f:2878 Ralink Technology, Corp.Im using Ubuntu 10.10 x64 with a Phenom(tm) II X6 System My results so far:
sudo modprobe rt2870sta (or rt2800usb)
result (rt2870sta) :
lsmod | grep rt28
Code:
rt2870sta 445182 0
crc_ccitt 1699 1 rt2870sta
dmesg
[code]....
View 9 Replies
View Related
Nov 2, 2010
I am unable to connect to wireless network in ubuntu 10.10.i have noticed that the iwlagn driver isnt been used by anything.
View 9 Replies
View Related
Apr 6, 2011
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....
View 5 Replies
View Related
Mar 6, 2010
I have installed opensuse 11.2 on a second partition, with the ultimate aim of leaving windows altogether. Unfortunately, I seem to be having terrible trouble (as do many others) getting my wireless internet connection working. I have viewed lots of posts in these forums and done everything I can think of, but since I am a linux novice, am unable to identify the problem. The card is working, since it can identify local SSIDs, it has been set up (to the best of my knowledge) correctly in YAST, but nothing seems to work.
I'll include some information I have recorded from my system.. I typed the commands below with the accompanying output listed:
[Code]....
View 2 Replies
View Related
Nov 7, 2010
Im a Linux newbie and am running OpenSuse 11.3 (Gnome, 2.6.34.7-0.5-desktop Kernel) and Ive an Asus N13 wifi dongle (linux compatible). I currently connect using my laptopś internal wifi but I bought the dongle due to trouble with weak signal. It came with some sort of code that can be "compiled" but I havent got a clue how to do that (and I have been researching this matter for quite some time now). I then came across a post where someone with the same USB stick created and added only two small files to his filesystem and it worked...for him (maybe becasuse he was on a different Distro )
Ralink RT2870 USB Stick and created the two files mentioned in the post (network_drivers.rules and network_drivers.conf) and placed them in ETC... etc, etc! I rebooted the system but NetworkManager only lists it as "device not ready" ... So now back to square one.
[Code]...
View 9 Replies
View Related
Jul 27, 2010
I just switched from Ubuntu to Fedora 13 because I was unable to get Ubuntu to connect to wireless networks. I tried everything suggested in help and forums, and kept getting "Bad Password" with WICD and Network Manager. Now, with Fedora...I still can't connect.
Problem #1: The guide says to "...make sure that the relevant wireless interface (usually eth0 or eth1) is controlled by NetworkManager," and that I do this via: System>Administration>Network
However, there is no Network option under System>Administration.
Problem #2: I open Network Manager, which displays a list of networks. I click on mine, configure it with WPA and the right password, and it fails to connect: "The network connection has been disconnected."
View 12 Replies
View Related
May 8, 2010
1. Sometimes when I try to shutdown my computer the display becomes filled with pixels of different colors as shown in the image (The problem is very random so I was not able to take a photo, I tried to recreate the effect using GIMP). Then the display turns off (Analog power saving mode) But my system never turns off.
2. While working on my computer the display sometimes goes kaput and blinks as in the second image. It stops responding completely I am not even able to go to terminal (Ctrl + Alt + F1). Leaving me with no option but to use the reset button. Causing me to loose all the work in progress.
3. Firefox responds very slowly upon closing it takes 5-6 seconds for the window to close.
PS:- KMS is also disabled in my system. Enabling it didn't improve stability. and here is the output of my videocard (lshw)
*-display UNCLAIMED
description: VGA compatible controller
product: 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device
vendor: Intel Corporation
[code]....
View 9 Replies
View Related
Sep 14, 2011
I have the above mentioned USB Wifi Dongle Bus 002 Device 003: ID 148f:3072 Ralink Technology, Corp. RT3072 Wireless Adapter It works extremely well using the KDE network manager but just will not connect using ifup traditional method through yast.
Initially it was using the RT2870 driver but this only gave wirelessg speeds (and still no ifup) but after blacklisting RT2780 and using RT5370sta driver draftn speed was achieved using KDE network manager however I still could not connect through ifup. The dongle scans and sees networks using ifup but will just not connect properly (NB security WPA2-AES).
View 9 Replies
View Related
Jan 15, 2009
im having problems finalizing the installation of fedora 10 on a new ASUS P5E-VM that uses Intel G35 chipset.
1. i think fedora did not recognize the video driver since all the installation was in text mode and i cannot use "init 5" to load a UI
2. i tried to find some drivers (if any1 can recommend a rpm that i can download i will apprichiate it very much) but could not transfer them to the fedora since i could not mount any USB disk on key in the linux i tried using: mount -t vfat /mnt/usb (after mkdir /mnt/usb)
3. i tried to burn the driver but then could not access the dvd...
4. no internet connection yet... but thats because i cannot access my network drives that are on the USB key as well...
View 3 Replies
View Related
Dec 29, 2010
I was having no problems (that I knew of) browsing the web since installing Ubuntu 10.10 a week or so ago. I was previously trialling Win7 as my customers will likely be using that in the future. Then I wanted to go to internode.on.net. Got the following: Quote: Firefox can't establish a connection to the server at internode.on.net. or Quote: Oops! Google Chrome could not connect to internode.on.net
As it was just after Christmas I thought it must be down, for upgrades or maintenance etc. I later tried to go to Freebsd.org; same error. I've been having a small number of other websites give the same error. I thought nothing of this until I tried it on my wife's macpro. I could log onto all the websites I wanted to and none gave any indication of having been down. Both boxes are on the same adsl connection. I still can't access internode or freebsd on 10.10 yet have been able to access every website on OSX. Now, I was only looking at them for info but am worried I won't be able to access something important. (so far everything I 'need' is working)
ping just drops out. edit: weirdest thing! I just retried and now can not emulate the problem for internode. freebsd still won't show. that is less than five minutes between problems and resolution! I hadn't even posted! But I still would like to have an idea of what is going on. Here is the ping error for freebsd: Quote:
[Code]...
View 9 Replies
View Related
Jul 14, 2010
I have Karmic Koala and together with my neighbours we have a W-LAN which I was always using without problems. Now, a couple of weeks ago, my neighbour has changed the password to this W-LAN and since then ubuntu is unable to connect. The network is being recognized, but after the request to unlock a key for the network manager (besides, how can I unlock it once for all?) there comes the window with the request for the network-password, after typing it (correctly), nothing happens. The request for the password comes two more times and then ubuntu states that it is unable to connect.
- We have changed the password again - didn't help
- On Windows I and my neighbours get the connection
- My Ubuntu is able to connect to all other W-LANs
View 3 Replies
View Related
Nov 16, 2010
I have an Ubuntu server dedicated to running an openVPN server on my VMware ESX 4 host. On my Windows clients I am able to connect to the VPN; however, on my Ubuntu 10.10 workstation I am unable to connect. Here is what I have done. I have network-manager-openvpn and dependices installed as well as the openvpn package. When I hit the add button in the network manager for VPNs, I fill out all the needed information, but am unable to hi the apply button. I have also tried using the openVPN method for connecting. I download the client.ovpn file from the VPN server, and issue the following command:
Code:
openvpn --config client.ovpn
It asks me for the authentication user and its password and produces this:
Code:
Mon Nov 15 21:37:20 2010 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables
Mon Nov 15 21:37:20 2010 Control Channel Authentication: tls-auth using INLINE static key file
Mon Nov 15 21:37:20 2010 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
[code]....
View 1 Replies
View Related
Jan 22, 2010
I have a rt2500 wireless USB adapter ( WLI-U2-KG54-AI ). I tried to use it on 2 computers loaded with Ubuntu 9.10. It worked well in WEP mode, but I am now trying to connect to a WPA router and the connection fails (the network manager icon keeps rolling forever). WPA works well on those machines when using another wireless adapter (not rt2500 based). This adapter also works well with WPA under windows. Is this device supposed to work with Ubuntu in WPA mode
View 9 Replies
View Related
Jul 17, 2010
I am running Ubuntu 10.04 (32-bit) on a MSI A5000 which appears to have a RaLink RT3090 wireless card. So far everything seems to work except the Wireless card.
The problem is that no option for wireless appears in the network manager, it only shows the options for wired connection. This computer does have a button on the front to enable/disable wireless and I have confirmed that is is on, as there is a green indicator light showing this.
Can anyone tell me the status of the RaLink RT3090 with Ubuntu 10.04? I have looked through various posts here about getting this card working with earlier versions of the OS, where complicated procedures with mixed and apparently intermittent results are described. Do these measures also need to be followed with 10.04?
I have attempted several older solutions found in assorted threads here and I am still unable to get the card to even so much as show up in the network manager. The proceedure which seemed the most promising is here [URL]
View 2 Replies
View Related
